1. DL manuals
  2. Jeep
  3. Automobile
  4. 2010 Wrangler
  5. Owner's Manual

Jeep 2010 Wrangler Owner's Manual

Summary of 2010 Wrangler

  • Page 1

    Wrangler o w n e r ’ s m a n u a l 2 0 1 0

  • Page 2: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 4: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 8 䡵 vehicle ide...

  • Page 5

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle designed for both on-road and off-roa...

  • Page 6

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a warranty information booklet, located on the dvd, and various customer-oriented documents. Please take the ti...

  • Page 7

    Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. How to use this manual consult the table of contents to determine w...

  • Page 8

    1 introduction 7.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in an accident or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 10: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 12 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . 13 䡵 steering wheel lock . . . . . . . . . . . . . . . . . . . . 1...

  • Page 11

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . 21 ▫ to turn off “flash lights with lock” . . . . . . . 21 ▫ programming additional transmitters . . . . . . 22 ▫ general information . . . . . . . . . . . . . . . . . . . 22 ▫ transmitter battery replacement . . . . . . . . . . 23 䡵 remote s...

  • Page 12

    ▫ rear center lap/shoulder belt retractor lockout (four-door models only) . . . . . . . . . 44 ▫ adjustable upper shoulder belt anchorage . . . 44 ▫ automatic locking retractors (alr) mode — if equipped . . . . . . . . . . . . . . . . . . . . . . . 46 ▫ seat belts in passenger seating positions . . ...

  • Page 13

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 14

    Warning! Leaving unattended children in a vehicle is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal, or the shift lever. Do not leave the key in the ignition. A child could operate power windows, other co...

  • Page 15

    Note: if you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it. Sentry key 姞 the sentry key 威 immobilizer system prevents unautho...

  • Page 16

    Caution! The sentry key 威 immobilizer system is not compat- ible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronic...

  • Page 17

    Customer key programming if you have two valid sentry keys 威, you can program new sentry keys 威 to the system by performing the following procedure: 1. Cut the additional sentry key 威 transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ign...

  • Page 18

    Reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed. General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cau...

  • Page 19

    To set the alarm the vehicle security alarm will set when you use the remote keyless entry (rke) transmitter to lock the doors and swing gate, or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the vehicle security light (located on the inst...

  • Page 20

    Note: • unlocking the doors with the manual door lock plung- ers or the driver’s door lock cylinder will not disarm the vehicle security alarm. • when the vehicle security alarm is armed, the interior power door lock switches will not unlock the doors. Illuminated entry the interior lights will come...

  • Page 21

    To unlock the doors and swing gate press and release the rke transmitter unlock button once to unlock the driver’s door only, or twice to unlock all the doors and swing gate. When the rke transmitter unlock button is pressed, the illuminated entry will initiate and the parking lights will flash twic...

  • Page 22

    1. Press the rke transmitter lock button for 4 to 10 seconds. 2. While the lock button is pressed (after four seconds), press the rke transmitter panic button. Release both buttons. The “sound horn on lock” feature can be reactivated by repeating this procedure. Using the panic alarm to turn the pan...

  • Page 23

    Note: pressing the rke transmitter lock button while you are in the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Press the rke transmitter unlock button to deactivate the ve- hicle security alarm. The “flash...

  • Page 24

    Transmitter battery replacement the recommended replacement battery is cr2032. Note: perchlorate material – special handling may apply; see www.Dtsc.Ca.Gov/hazardouswaste/ perchlorate. 1. If the rke transmitter is equipped with a screw, remove the screw. With the rke transmitter buttons facing down,...

  • Page 25

    Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system...

  • Page 26

    To enter remote start press and release the remote start button on the rke transmitter twice, within five sec- onds. The parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the remote start mode for a 15-minute cycle. No...

  • Page 27

    To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, press and release the unlock button on the rke transmitter to unlock the doors and disarm the vehicle security alarm (if equipped). Then, insert the key into the ignition switch and turn the switch to the on posit...

  • Page 28

    Upper half door window installation — if equipped 1. Grasp the half door window and line up pins into pockets in lower door. 2. Push down to ensure the half door window is fully seated. Front door removal 1. Remove the hinge pin screws from the upper and lower outside hinges (using a #t50 torx 威 hea...

  • Page 29

    Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock the connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected. 3. Unhook the door strap from ...

  • Page 30

    2. Slide the front seat(s) fully forward. 3. Remove the trim access door from the bottom of b-pillar. 4. Unplug the wiring harness connector. Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This ...

  • Page 31

    5. Unhook the door strap from the body hook. 6. With the door open, lift the door to clear hinge pins from their hinges, and remove door. To reinstall the door(s), perform the previous steps in the opposite order. Door locks manual door locks the front (two-door models) and rear doors (four-door mod...

  • Page 32

    Note: the ignition key that is used to start the vehicle is used to lock or unlock the doors, swing gate, and console storage. Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. • never leave chil...

  • Page 33

    Warning! (continued) • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power win- dows, other controls, or move...

  • Page 34

    Note: use the “automatic unlock doors on exit” feature in accordance with local laws. Automatic door locks the doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1. The “automatic door locks” feature is enabled. 2. The transmission is in gear....

  • Page 35

    Windows power windows — if equipped the power window switches are located on the instru- ment panel center stack (below the radio). The top left switch controls the left front window and the top right switch controls the right front window. The lower left switch controls the left rear passenger wind...

  • Page 36

    Auto-down both the driver and front passenger window switches have an “auto-down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the auto-down move- ment, operate the switch in either the up or down direction and release the swit...

  • Page 37

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down in certain open or partially open posi- tions. This is a normal occurrence and can be minimized by adjusting ...

  • Page 38

    Caution! Do not press on rear wiper blade when closing the rear flip-up window, as damage to the blade will result. Warning! Driving with the flip-up window open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flip-up window clos...

  • Page 39

    If you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for children (latch) feature also can be used to hold infant and child restraint systems. For more information on latch, see lower anchors and tether for children (latch). Note: the ...

  • Page 40

    Ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/shoulder belts all seating positions in your vehicle are equipped with lap/shoulder belts. The belt webbing retractor is de- signed to lock during very sudden ...

  • Page 41

    Warning! (continued) • two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. Lap/shoulder belt operating ...

  • Page 42

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your bel...

  • Page 43

    Warning! (continued) • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thigh...

  • Page 44

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt cannot do its job as well. In a collision,...

  • Page 45

    Rear center lap/shoulder belt retractor lockout (four-door models only) this feature is designed to lock the retractor whenever the 60% rear seatback is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seatback is not fully latched. Note: • if the...

  • Page 46

    Warning! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. As a guide, if you are shorter than average, you ...

  • Page 47

    Automatic locking retractors (alr) mode — if equipped in this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is avail- able on all passenger-seating positions with a combina- tion lap/shoulder bel...

  • Page 48

    Left center right first row alr second row alr alr alr third row if the passenger seating position is equipped with an alr and is being used for normal usage: only pull the belt webbing out far enough to comfortably wrap around the occupants mid-section so as to not activate the alr. If the alr is a...

  • Page 49

    (beltalert 威) will alert the driver or front passenger to buckle the seat belt. The driver should also instruct all other occupants to buckle their seat belts. Once the warning is triggered, beltalert 威 will continue to chime and flash the seat belt reminder light for 96 seconds or until the driver’...

  • Page 50

    4. Turn the ignition key to the off position. A single chime will sound to signify that you have successfully completed the programming. Beltalert 威 can be reactivated by repeating this procedure. Note: although beltalert 威 has been deactivated, the seat belt reminder light will continue to illumina...

  • Page 51

    Supplemental restraint system (srs) — airbags this vehicle has advanced front airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s advanced front airbag is mounted in the steering wheel. The front passenger airbag is mounted in the in...

  • Page 52

    The advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation ra...

  • Page 53

    Warning! • no objects should be placed over or near the airbag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the airbag to inflate. • do not put anything on or around the advanced front airbag covers or attempt to manually ...

  • Page 54

    The advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on the severity and type of collision. Along with the seat belts, advanced front airbags work with the instrument panel knee bolsters to provide improved protectio...

  • Page 55

    3. The driver and front passenger seats should be moved back as far as practical to allow the advanced front airbags room to inflate. 4. Do not lean against the door or window. If your vehicle has side airbags, and deployment occurs, the side airbags will inflate forcefully into the space between yo...

  • Page 56

    Airbag system components your vehicle may be equipped with the following airbag system components: • occupant restraint controller (orc) • airbag warning light • steering wheel and column • instrument panel • knee impact bolster • driver advanced front airbag • passenger advanced front airbag • supp...

  • Page 57

    The advanced front airbags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, advanced front airbags...

  • Page 58

    It also includes diagnostics that will illuminate the instrument cluster airbag warning light if a malfunc- tion is noted that could affect the airbag system. The diagnostics also record the nature of the malfunction. Warning! Ignoring the airbag warning light in your instru- ment panel could mean y...

  • Page 59

    The orc determines if a side collision requires the side airbags to inflate based on the severity and type of collision. Based on the severity and type of collision, the side airbag inflator on the crash side of the vehicle is trig- gered, releasing a quantity of non-toxic gas. The inflating side ai...

  • Page 60

    Note: front and/or side airbags will not deploy in all collisions. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: • the nylon airbag material may sometimes cause abra- sions and/or skin redden...

  • Page 61

    Maintaining your airbag system warning! • modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the stee...

  • Page 62

    Vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The edr in this vehicle is designed to record such data as: • how various systems in your vehicle were operating; • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if ...

  • Page 63

    Children 12 years and under should ride properly buck- led up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats, rather than in the front. There are different sizes and types of restraints for children from newborn size to the ...

  • Page 64

    • the infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “convertible” child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children w...

  • Page 65

    Here are some tips for getting the most out of your child restraint: • before buying any restraint system, make sure that it has a label certifying that it meets all applicable safety standards. The manufacturer also recommends that you try a child restraint in the vehicle seats where you will use i...

  • Page 66

    • buckle the child into the restraint exactly as the manufacturer’s instructions tell you. • when your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the oc...

  • Page 67

    • check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • if the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind the back. Note: for additional ...

  • Page 68

    Note: if your child restraint seat is not latch- compatible, install the restraint using the vehicle seat belts. Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a...

  • Page 69

    Note: when using the latch attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked be...

  • Page 70

    Installing the latch-compatible child restraint system we urge you to carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provide...

  • Page 71

    In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch anchorages (four-door models) tether strap mounting (two-door models) 70 things to know before starting your vehicle.

  • Page 72

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means for adjusting the tension of the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also b...

  • Page 73

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 74

    2. Finally, pull on any excess webbing to tighten the lap portion around the child restraint. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. To attach a child restraint tether strap: route the tether strap over the seatback and attach the ...

  • Page 75

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Vehicles with rear web buckles that may need to be twisted • in the rear seat...

  • Page 76

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 77

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), whi...

  • Page 78

    Damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each ...

  • Page 79

    They cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attache...

  • Page 80

    Warning! (continued) failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle. Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread we...

  • Page 82: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 86 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 87 ▫ vanity mirrors . . . . . . . . . . . . . . . . ...

  • Page 83

    ▫ manual seat height adjustment — if equipped . . . . . . . . . . . . . . . . . . . . . . 126 ▫ front seatback recline . . . . . . . . . . . . . . . . . 126 ▫ front easy entry seats — two door models . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 ▫ head restraints . . . . . . . . . . . . ...

  • Page 84

    䡵 windshield wipers and washers . . . . . . . . . . 141 ▫ windshield wiper operation . . . . . . . . . . . . 142 ▫ intermittent wiper system . . . . . . . . . . . . . . 143 ▫ windshield washers . . . . . . . . . . . . . . . . . . 143 ▫ mist feature . . . . . . . . . . . . . . . . . . . . . . . . 144...

  • Page 85

    䡵 freedom top™ three-piece modular hard top — if equipped . . . . . . . . . . . . . . . . . . . . . . . . 160 ▫ front panel(s) removal . . . . . . . . . . . . . . . . 161 ▫ freedom top™ storage bag . . . . . . . . . . . . . 163 ▫ front panel(s) installation . . . . . . . . . . . . . . 167 ▫ front pa...

  • Page 86

    䡵 sunrider威 (two-door models) — if equipped . 231 ▫ opening the sunrider威 . . . . . . . . . . . . . . . . 232 ▫ closing the sunrider威 . . . . . . . . . . . . . . . . 234 䡵 sunrider威 (four-door models) — if equipped . 234 ▫ opening the sunrider威 . . . . . . . . . . . . . . . . 235 ▫ closing the sunri...

  • Page 87

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward...

  • Page 88

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than the...

  • Page 89

    Vanity mirrors vanity mirrors are located on the sun visors. To use the mirrors, rotate the sun visor down and swing the mirror cover upward. Uconnect™ phone — if equipped uconnect™ phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ phone al- lows you to dial a phon...

  • Page 90

    • www.Jeep.Com/uconnect • or call 1–877–855–8400 uconnect™ phone allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The uconnect™ phone is driven through your bluetooth 威 ...

  • Page 91

    Note: the driver side upper windshield trim contains the microphone for the uconnect™ phone. Voice command button actual button location may vary with the ra- dio. The individual buttons are described in the “operation” section. The uconnect™ phone can be used with any hands-free profile certified b...

  • Page 92

    • for each feature explanation in this section, only the compound form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the compound form voice command ⬙phonebook new entry,⬙ or you can brea...

  • Page 93

    The following are general phone to uconnect™ phone pairing instructions: • press the button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙setup phone pairing.⬙ • when prompted, after the beep, say ⬙pair a phone⬙ and follow the audible prompts. • you will be asked to say a four-di...

  • Page 94

    • the system will prompt you to say the number you want to call. • for example, you can say ⬙234-567-8901⬙. • the uconnect™ phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by saying a name • press the button to begin. • after the ⬙read...

  • Page 95

    • when prompted, enter the number designation (e.G., ⬙home,⬙ ⬙work,⬙ ⬙mobile,⬙ or ⬙pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. • when prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry...

  • Page 96

    • depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previous downloaded phonebook is available for use. • only the phonebook of the currently connected cellu- lar phone is accessible. • ...

  • Page 97

    • some phones cannot send phonebook entries if they are already connected to any system via bluetooth 威, and you may see a message on the phone display that the bluetooth 威 link is busy. In this case, the user must first disconnect or drop the bluetooth 威 connection to the uconnect™ phone, and then ...

  • Page 98

    Cellular and a home number, but you can add ”john doe’s” work number later using the ⬙phonebook edit⬙ feature. Delete uconnect™ phonebook entry note: editing phonebook entries is recommended when the vehicle is not in motion. • press the button to begin. • after the ⬙ready⬙ prompt and the following ...

  • Page 99

    • the uconnect™ phone will ask you to verify that you wish to delete all the entries from the phonebook. • after confirmation, the phonebook entries will be deleted. • note that only the phonebook in the current language is deleted. • automatic downloaded phonebook entries cannot be deleted or edite...

  • Page 100

    Answer or reject an incoming call - no call currently in progress when you receive a call on your cellular phone, the uconnect™ phone will interrupt the vehicle audio sys- tem, if on, and will ask if you would like to answer the call. Press the button to accept the call. To reject the call, press an...

  • Page 101

    Toggling between calls if two calls are in progress (one active and one on hold), press the button until you hear a single beep, indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at a time. Conference call when two calls are in progress (o...

  • Page 102

    Call continuation call continuation is the progression of a phone call on the uconnect™ phone after the vehicle ignition key has been switched to off. Call continuation functionality avail- able on the vehicle can be any one of three types: • after the ignition key is switched to off, a call can con...

  • Page 103

    Emergency assistance if you are in an emergency and the cellular phone is reachable: • pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the uconnect™ phone is operational, you may reach the emergency number as follows: • press the button to be...

  • Page 104

    Towing assistance if you need towing assistance: • press the button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙towing assistance.⬙ note: • the towing assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the u.S., 1-877-213-4525 f...

  • Page 105

    When calling a number with your uconnect™ phone that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the button and say the sequence you wish to enter, followed by the word ⬙send.⬙ for example, if required to enter your pin followed with a pound, ...

  • Page 106

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G., the uconnect™ phone will not repeat a phone number before you dial it). • press the button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙setup confirmatio...

  • Page 107

    Mute/un-mute (mute off) when you mute the uconnect™ phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect™ phone: • press the button. • following the beep, say ⬙mute.⬙ in order to un-mute th...

  • Page 108

    • when prompted, say ⬙list phones.⬙ • the uconnect™ phone will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “select” or “delete.” also, see the next two sec- tions...

  • Page 109

    Things you should know about your uconnect™ phone uconnect™ phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect™ tutorial.” voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect™ pho...

  • Page 110

    Voice command • for best performance, adjust the rearview mirror to provide at least 1 ⁄ 2 in (1 cm) gap between the overhead console (if equipped) and the mirror. • always wait for the beep before speaking. • speak normally, without pausing, just as you would speak to a person sitting a few feet/me...

  • Page 111

    • numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • you can say ⬙o⬙ (letter ⬙o⬙) for ⬙0⬙ (zero). • even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • in a ...

  • Page 112

    Sms uconnect™ phone can read or send new messages on your phone. Read messages: if you receive a new text message while your phone is connected to uconnect™ phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • press the button. • ...

  • Page 113

    List of preset messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L o l 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See you in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18....

  • Page 114

    Turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and the following beep, say “setup, incoming message announcement,” you will then be given a choice to chan...

  • Page 115

    114 understanding the features of your vehicle.

  • Page 116

    3 understanding the features of your vehicle 115.

  • Page 117

    116 understanding the features of your vehicle.

  • Page 118

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 3 understa...

  • Page 119

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous record again voice commands primary alternate(s) redial return to main menu return or main menu select phone select send set up...

  • Page 120

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 121

    Note: if you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system i...

  • Page 122

    Commands the voice command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the volume 1. Start a dialogue by pressing the voice command button. 2. Say a command (e.G., “help”). 3. Us...

  • Page 123

    Radio fm to switch to the fm band, say “fm” or “radio fm”. In this mode, you may say the following commands: • “frequency” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “mai...

  • Page 124

    Memo to switch to the voice recorder mode, say “memo”. In this mode, you may say the following commands: • “new memo” (to record a new memo) — during the recording, you may press the voice command button to stop recording. You proceed by saying one of the following commands: − “save” (to save the me...

  • Page 125

    Note: keep in mind that you have to press the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect™ voice “voice training” feature may be u...

  • Page 126

    Front seat adjustment move the seat forward or rearward by lifting the lever. Release the lever when the seat is in the desired position. Using body pressure, move forward and rearward on the seat to make sure that the latch is fully engaged. Warning! Adjusting a seat while the vehicle is moving is ...

  • Page 127

    Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat. Pull upward on the handle to raise the seat; push downward on the handle to lower the seat. Front seatback recline lean forward befo...

  • Page 128

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seatbelt and be seriously or fatally injured. Use the recliner only when the vehicle is parked. Front easy entry seats — two door models push th...

  • Page 129

    1. To return the seat to a sitting position, rotate the seatback upright until it locks. 2. Push the seat rearward until the track locks. Note: • if equipped with combination lever the seatback will return to its first locked position. The recliner handle will have to be actuated to adjust the seatb...

  • Page 130

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint. Note: the rear head restraints are not adjustable. To remove the head restraint, pull upward on the...

  • Page 131

    To install the head restraint, insert the head restraint rods into each guide, apply pressure down on the headrest until the head restraint reaches the first lock position, push the large button in and push down and adjust head restraint to desired position. Note: ensure that the front of the head r...

  • Page 132

    2. Slowly flip the entire seat forward. 3. Return the seat to the normal position. 4. Raise the rear seatback using the assist strap and firmly lock the seat into position. Rear seat release folding rear seat 3 understanding the features of your vehicle 131.

  • Page 133

    Removing the rear seat — two door models warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • do not allow people to ride in any area of your vehicle that is n...

  • Page 134

    3. Fold the rear seat forward following steps 1 through 3 under “fold and tumble rear seat” in this section. 4. Press down on the release bar on each side, and pull the seat out and away from the lower bracket. 5. Remove the seat from the vehicle. Replacing the rear seat — two door models reverse th...

  • Page 135

    Note: • prior to folding the rear seat, it may be necessary to reposition the front seat to its mid-track position. • be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. Warning! • it is extremely dangerous to ride in a cargo area...

  • Page 136

    To raise the rear seat raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Note: if the rear seatback is not fully latched, the center shoulder belt will not be ab...

  • Page 137

    To close the hood, remove the support rod from the hood panel and place it in the retaining clip. Lower the hood slowly. Secure both of the hood latches. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in mot...

  • Page 138

    Note: lens fogging can occur under certain weather conditions. Turning the headlights on will usually accel- erate the clearing process. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear tur...

  • Page 139

    Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. • a tone will chime if the turn signals are left on for ...

  • Page 140

    Instrument panel dimmer rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument panel...

  • Page 141

    Interior lights the overhead light will turn on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the multifunction lever fully upward. The overhead light will automatically turn off in approxi- mately 10 minutes if a door is left open or the dimmer con...

  • Page 142

    When a door is open and the interior lights are on, rotating the dimmer control to the extreme bottom posi- tion will cause all the interior lights to turn off. This is also known as the ⬙party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehicl...

  • Page 143

    Windshield wiper operation rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper opera- tion. Front wiper control 142 understan...

  • Page 144

    Caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. Intermittent wiper ...

  • Page 145

    If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles and then turn off. Warning! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield ...

  • Page 146

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or...

  • Page 147

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this war...

  • Page 148

    System can be reactivated by pushing the electronic speed control on/off button and resetting the desired vehicle set speed. To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To turn the elec- tronic speed control system off, push the on/off bu...

  • Page 149

    To vary the speed setting when the electronic speed control is set, you can in- crease speed by pushing up and holding the resume accel lever. If the lever is continually held in the resume accel position, the set speed will continue to increase until the lever is released, then the new set speed wi...

  • Page 150

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 151

    Electrical power outlet there are two 12 volt (13 amp) auxiliary power outlets that can provide power for accessories designed for use with the standard power outlet adapters. The power outlet, located in the lower portion of the instrument panel, has a snap-on plastic cap so that it can be covered ...

  • Page 152

    The right-side power outlet is powered directly from the battery (power available at all times). Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting. Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet s...

  • Page 153

    Caution! (continued) • power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Cupholders front cupholders the front cupholders are located in the center console. Note: the front cupholder insert is removable for cleaning. Front cu...

  • Page 154

    Rear cupholders the rear cupholders are located on the back of the center console. Storage console storage compartment to lock or unlock the storage compartment, insert the ignition key and turn. To open the storage compartment, press the latch and lift the cover. Rear cupholders center console 3 un...

  • Page 155

    Rear storage compartment the rear storage compartment cover is held by a spring- loaded latch. In order to remove the rear storage com- partment cover, use the following procedure: note: the rear storage compartment latch should not be used as cargo tie-down. 1. Flip up the pull loop so it is perpen...

  • Page 156

    Hard top are to be used independently. Removal is mandatory to prevent any possible wear and tear on the soft top. Your vehicle warranty will not cover damage resulting from both tops remaining on the vehicle at the same time for extended periods of time. Removing the soft top 1. Locate and remove t...

  • Page 157

    4. Disconnect the knuckles from the left and right metal pivot brackets. Remove the soft top from the vehicle and store in a clean, dry location. Note: to aid in disconnecting the knuckles, you may carefully tap on the knuckles using a rubber mallet. 5. Unzip the zipper on the sport bar cover to exp...

  • Page 158

    Installing the soft top note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this section. 1. Locate and remove the following items prior to hard top removal: • right and left door frames • door frame attachment knobs (four for two-doo...

  • Page 159

    A. If the pivot brackets have been removed, unzip the sport bar covers and attach the pivot brackets to the sports bar with the four screws that were removed using a #t30 torx 威 head driver. Re-cover and re-zip the sport bar covers. B. Lay the soft top into the rear of the vehicle with the bows poin...

  • Page 160

    D. Screw the pivot screws back into place using a #t30 torx 威 head driver. Secure them until they are snug, being careful not to cross-thread the screws or over- tighten. Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 5. Remove the swing gate bar (black m...

  • Page 161

    Freedom top™ three-piece modular hard top — if equipped caution! • the hard top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus ca...

  • Page 162

    Front panel(s) removal note: left panel must be removed before removing right panel. 1. Fold down the sun visor, and move it to the side. 2. Turn the rear fasteners (knobs) (located on the over- head speaker bar assembly) counterclockwise until they can be removed. 3. Turn the center l-shaped locks ...

  • Page 163

    4. Turn the rear l-shaped lock (located above the shoul- der belt anchorage). 5. Unlatch the header panel latch located at the top of the windshield. 6. Remove the left-hand panel. To remove the right panel, follow the steps above except for step 3. 162 understanding the features of your vehicle.

  • Page 164

    Freedom top™ storage bag your vehicle comes with a freedom top™ storage bag that allows you to store your freedom top™ panels. The storage bag contains two compartments and fits behind the rear seat. Lay the freedom bag down so the loops and hooks are facing downward. Unzip the bag and fold back the...

  • Page 165

    Unfold the black panel divider (ensure the divider is laying flat). Secure the velcro, located at the center of the divider. Insert the left-side freedom panel into the bag with the latches facing upward. Note: ensure the front freedom panel latch is closed prior to inserting the panel into the bag....

  • Page 166

    Unfold the outer flap and zip the freedom bag closed. Install the seat attachment strap (at the top of the bag) through the loops. 3 understanding the features of your vehicle 165.

  • Page 167

    Lift the freedom bag into the vehicle with the hooks and straps facing the back of the rear seat. Attach the clips at the bottom of the bag to the child restraint anchorages, located at the base of the rear seat. Wrap the upper strap around the rear head restraints and loop the strap through the buc...

  • Page 168

    Front panel(s) installation note: set the panels on the windshield frame so that there is no overhang. Also, make sure that the panels are sitting flush with the body. 1. Install the right panel first, then the left panel. 2. Reinstall the panel(s) using the same steps for removal in reverse order. ...

  • Page 169

    2. Install the right panel first, then the left panel. 3. Reinstall the panel(s) using the same steps for removal in reverse order. Rear hard top removal 1. Remove both front panels. Refer to “front panel(s) removal” in this section. 2. Open both doors. 3. Remove the two torx 威 head screws that secu...

  • Page 170

    6. Locate the wire harness on the left rear inside corner of the vehicle. 7. Release the red locking tab by pushing upward. 3 understanding the features of your vehicle 169.

  • Page 171

    8. To remove the wiring harness press the side tab and pull to disconnect. Note: if necessary, pliers can be used to lightly squeeze grips while disconnecting the washer hose. 9. To remove the washer hose, pinch the grips on hose connector and pull. 10. Close the swing gate. 11. Remove the hard top ...

  • Page 172

    Rear hard top installation note: if the door frames are installed from soft top usage, they must be removed prior to installation of the hard top. 1. Inspect the hard top seals for damage and replace if necessary. 2. Install the hard top using the same steps for removal in reverse order. Make sure t...

  • Page 173

    Caution! (continued) • careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle’s interior. • the door frame(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. D...

  • Page 174

    2. Place one hand on the upper rear and one hand on the front of the door frame. 3. Pull the frame toward you with your rearward hand to remove the frame from the vehicle. 4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Warning! Never store the door fram...

  • Page 175

    Door frame installation — two-door models 1. Unfold door frame and unscrew thumbscrews. 2. Set the door frame pin into the hole on top of the body side, behind the door opening. 3. After the door frame pin has been set into the body side hole, carefully set the front of the door frame into the rubbe...

  • Page 176

    5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. Door frame removal — four-door models 1. Unscrew and remove the two forward most door frame attachment knobs. Warning! Use both hands to remove the door frames. The door frames will fold and could cause injur...

  • Page 177

    2. Place one hand on the upper rear and one hand on the upper front of the front door frame. 3. Pull the frame toward you with your front hand to remove the frame from the vehicle. 4. Unscrew and remove the remaining door frame at- tachment knob on the rear door frame. 176 understanding the features...

  • Page 178

    5. Place one hand on the upper rear and one hand on the upper front of the rear door frame. Pull the frame toward you with your rear hand to remove the frame from the vehicle. 6. Screw the knob back into the door frame and fold for storage. Store in a secure location. Warning! Never store the door f...

  • Page 179

    Door frame installation — four-door models 1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening. 3. Position the top of the door frame against the metal sport bar and press onto the side bar making sure not to pinch ...

  • Page 180

    5. Carefully set the front of the front door frame in the rubber seal at the top of the windshield. Then, clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched by the door frame. Position the rear of the front door frame to lay on top o...

  • Page 181

    Soft top — two door models please visit the owners section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a struct...

  • Page 182

    Caution! (continued) • refer to “appearance care for fabric top models” in “maintaining your vehicle” for further infor- mation. It contains important information on cleaning and caring for your vehicle’s fabric top. • do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clip...

  • Page 183

    Caution! (continued) • careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle’s interior. • the soft top must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. Quick steps to loweri...

  • Page 184

    2. Release header latches from the windshield frame. 3. Release the sunrider 威 latch (both sides). 3 understanding the features of your vehicle 183.

  • Page 185

    4. Open the swing gate and lower the top. Note: ensure fabric does not overhang the sides of the vehicle. Quick steps to raising the soft top refer to “raising the soft top” in this section for further information. 1. Open the swing gate and raise the top, engaging the sunrider 威 latches (another pe...

  • Page 186

    2. Engage header latches. 3 understanding the features of your vehicle 185.

  • Page 187

    3. Install rear corner panels. 4. Install side and back windows. 186 understanding the features of your vehicle.

  • Page 188

    Lowering the soft top 1 — header bow 6 — quarter window 2 — 2–bow 7 — check strap 3 — 3–bow 8 — front retainer — quarter window 4 — sail panel 9 — bottom retainer — quarter window 5 — body side retainer 3 understanding the features of your vehicle 187.

  • Page 189

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 188 understanding the features of your vehicle.

  • Page 190

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 191

    5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across th...

  • Page 192

    6. Undo the velcro 威 that runs along the top and rear edge of the side window. 7. Beginning from the rear lower corner, completely unzip the window. 8. Once unzipped, remove the side window retainers from the door channel and body side channel. Repeat this step on the opposite side. 9. Finish releas...

  • Page 193

    10. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top. 11. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket ba...

  • Page 194

    The sunrider 威 package, proceed to step 15. 13. Make sure the plastic sleeves are slid rearward over the sunrider 威 link (sunrider威 models only). 3 understanding the features of your vehicle 193.

  • Page 195

    14. Unlatch the side bows from both door rails (sun- rider 威 models only). 15. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Move to the front of the vehicle. Grasp the side bow behind the header and lift the top, folding it towa...

  • Page 196

    16. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle. 17. Close the front header latches. 18. Remove the door frames, if desired. Refer to “door frame” in this section for further informati...

  • Page 197

    4. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow (middle bow) up and over the sports bar until the header rests on the top of the windshield frame. 5. Make sure the sunrider 威 bracket on the side bows latches to the door rails (sunrider 威 models only). 196 understan...

  • Page 198

    6. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 7. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel u...

  • Page 199

    8. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow. 9. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to reac...

  • Page 200

    10. To install the side windows, affix the window tem- porarily by attaching to the velcro 威 in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 11. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on...

  • Page 201

    12. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro 威 along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 202

    13. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 3 understanding the features of your vehicle 201.

  • Page 203

    14. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 15. Run the zipper fully around to the right side of the window. 202 understanding the features of ...

  • Page 204

    16. Grasp the swing gate bar and position it into the swing gate brackets. 17. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel. 18. Close the header latches and return the sun visors to their secu...

  • Page 205

    Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any addi- tional loads other than enviro...

  • Page 206

    Caution! (continued) • refer to “appearance care for fabric top models” in “maintaining your vehicle” for further infor- mation. It contains important information on cleaning and caring for your vehicle’s fabric top. • do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clip...

  • Page 207

    Caution! (continued) • careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle’s interior. • the soft top must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. Note: do not remove a...

  • Page 208

    Quick steps for lowering the soft top 1. Remove the side and back windows. 2. Release header latches from the windshield frame. 3 understanding the features of your vehicle 207.

  • Page 209

    3. Fold header rearward, pulling the fabric to the rear. 208 understanding the features of your vehicle.

  • Page 210

    4. Release sunrider 威 latch (both sides). 5. Open the swing gate and lower the top. Note: ensure the fabric does not overhang the sides of the vehicle. 3 understanding the features of your vehicle 209.

  • Page 211

    Quick steps for raising the soft top 1. Open the swing gate and raise the top, engaging the sunrider 威 latches (another person may be needed to help with this operation). 210 understanding the features of your vehicle.

  • Page 212

    2. Install rear corner panels. 3. Rotate the header forward. 3 understanding the features of your vehicle 211.

  • Page 213

    4. Engage the header latches. 5. Install the side and back windows. 212 understanding the features of your vehicle.

  • Page 214

    Folding down the soft top 1 — header bow 6 — body side retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 3 understanding the features of your vehicle 213.

  • Page 215

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 214 understanding the features of your vehicle.

  • Page 216

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 217

    5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across th...

  • Page 218

    6. Undo the velcro 威 that runs along the top and rear edge of the side window. 7. Beginning from the rear lower corner, completely unzip the window. 8. Once unzipped, remove the side window retainers from the door channel and body side channel. Repeat this step on the opposite side. 9. Finish releas...

  • Page 219

    10. Fold the sail panels so that they rest on top of the soft top. 11. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to dis...

  • Page 220

    12. Grasp the front side bow behind the header, and lift the top. 13. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck. 3 understanding the features of your vehicle 219.

  • Page 221

    14. Fold the top so that the material forms a ⬙w⬙ as shown. Enter the vehicle and move the material into two folds. 15. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 220 understanding the ...

  • Page 222

    16. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Grasp the folded side bows and slide the top along the door frame track to the rear door frame. 17. Gently slide the side bows off the door frame track and lower the top down into...

  • Page 223

    Strap around the side bows and through the slot on the body. 20. Close the front header latches. 21. Remove the door frames, if desired. Refer to “door frame” in this section for further information. Putting up the soft top note: be extremely careful when putting up the soft top to prevent the doors...

  • Page 224

    4. Grasp the folded side bows and lift to the top of the rear door frames. Note: help from another person will ease this opera- tion. 5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward. 3 understanding the features of your vehicle 223.

  • Page 225

    6. Ensure that the top locks into the sunrider 威 locking mechanisms that are located above the front of the rear doors. 7. Unclip and move the sun visors to the side. 8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 224 understanding the fe...

  • Page 226

    9. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 10. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel ...

  • Page 227

    11. Ensure that the straps are positioned correctly before pulling the sail panels over the rear roof bow (4–bow). Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (4–...

  • Page 228

    12. To install the side windows, affix the window tem- porarily by attaching it to the velcro 威 in the upper rear corner. Start the zipper but close only about 1 in (2.5 cm). 13. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly posi...

  • Page 229

    14. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro 威 along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 230

    15. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 3 understanding the features of your vehicle 229.

  • Page 231

    16. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 17. Run the first zipper fully around to the right side of the window. 18. Grasp the swing gate bar...

  • Page 232

    19. Complete the installation of the sail panel by insert- ing the rest of the retainer into the body channel. 20. Close the header latches and return the sun visors to their secured position. Sunrider 姞 (two-door models) — if equipped caution! Operating the top, opening a door or lowering a window ...

  • Page 233

    Opening the sunrider 姞 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Slide the plastic sleeve forward. 232 understanding the features of your vehicle.

  • Page 234

    4. Grasp the header and lift the top back. Make sure the material is folded back as shown. Note: the sunrider 威 latch on the door rail should not be activated for sunrider 威 use. If activated, the soft top must be reinstalled starting from the sail panels. 5. Locate the straps to secure the side bow...

  • Page 235

    Closing the sunrider 姞 1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the front of the vehicle. 4. Hook the header latches to the loops on the wind- shield frame, close latches, and return the sun visors to their origi...

  • Page 236

    Opening the sunrider 姞 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Grasp the front side bow behind the header, and lift the top. 3 understanding the features of your vehicle 235.

  • Page 237

    4. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 5. Fold the top so that the material forms a ⬙w⬙ as shown. Enter the vehicle and move the material into two folds. 236 understanding the features of your vehicle.

  • Page 238

    6. Secure the top by using the two provided straps. Each strap will wrap around the side bow and velcro 威 to itself; use one strap on each side of the vehicle. Closing the sunrider 姞 perform the above steps in the opposite order. Note: failure to fold the fabric rearward will allow the material to s...

  • Page 239

    Rear window features — hard top only rear window wiper/washer — if equipped a rotary switch on the center portion of the control lever (located on the right side of the steering column) controls the operation of the rear wiper/washer function. Rotate the switch upward to the first detent posi- tion ...

  • Page 240

    Rear window defroster — if equipped the rear window defroster button is located on the bottom right-side of the blower control knob. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster auto...

  • Page 242: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 244 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 245 䡵 instrument cluster descriptions . . . . . . . . . . . 246 䡵 compass and trip computer — if equipped . . 261 ▫ control buttons ...

  • Page 243

    ▫ operating instructions — voice command system — if equipped . . . . . . . . . . . . . . . . . 283 ▫ operating instructions — uconnect™ phone — if equipped . . . . . . . . . . . . . . . . . . . . . . 283 ▫ clock setting procedure — rbz radio . . . . . 283 ▫ clock setting procedure — rer/ren radio ....

  • Page 244

    ▫ electronic serial number/sirius identification number (esn/sid) . . . . . . . . . 312 ▫ selecting uconnect™ multimedia (satellite) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ satellite antenna . . . . . . . . . . . . . . . . . . . . . 313 ▫ reception quality . . . . . . . ...

  • Page 245

    Instrument panel features 1 — air outlet 6 — climate controls 2 — instrument cluster 7 — power outlet 3 — horn 8 — lower switch bank 4 — radio 9 — auxiliary power outlet / cigar lighter 5 — glove compartment 244 understanding your instrument panel.

  • Page 246

    Instrument cluster 4 understanding your instrument panel 245.

  • Page 247

    Instrument cluster descriptions 1. Fuel gauge the pointer shows the level of fuel in the fuel tank. Note: when the ignition switch is turned to off, the fuel gauge and temperature gauge may not show accu- rate readings. When the engine is not running, turn the ignition switch to on to obtain accurat...

  • Page 248

    7. Seat belt reminder light a warning chime and an indicator light will alert you to buckle the seat belts. When the belt is buckled, the chime will stop, but the light will stay on for about six seconds, until it times out. Refer to “occupant restraints” in “things to know before start- ing your ve...

  • Page 249

    11. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake syste...

  • Page 250

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs), are also equipped with el...

  • Page 251

    13. Airbag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned on. If the light is either not on during starting, stays on, or turns on while driving, then have the system inspected at an authorized dealer as soon as possible. Refe...

  • Page 252

    18. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or ...

  • Page 253

    21. Odometer / trip odometer / eco (fuel saver indicator) button press this button to change the display from odometer to either of the two trip odometer settings or the “eco” display. Trip a or trip b will appear when in the trip odometer mode. Press and hold the button for two seconds to reset the...

  • Page 254

    Maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicato...

  • Page 255

    24. Odometer / trip odometer display area the odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “odometer / trip odometer / eco (fuel saver indicator) button” for additional information. U.S. Federal regulations require that upon...

  • Page 256

    The eco display will toggle between eco and eco-on depending on driving habits and vehicle usage. Press the odometer / trip odometer / eco (fuel saver indicator) button to change the display from odometer to either of the two trip odometer settings or the “eco” display. Low tire when the appropriate...

  • Page 257

    Gascap if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will display in the odometer display area. Tighten the fuel filler cap properly and press the trip odometer button to turn off the message. If the problem contin...

  • Page 258

    1. Turn the ignition switch to the on position (do not start the engine). 2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates when you start the vehicle, the oil change indicator...

  • Page 259

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injur...

  • Page 260

    Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent acci- dents, including those resulting from excessive speed in turns, driving on very s...

  • Page 261

    Warning! If a warning light remains on the system may not be working and you will not have the benefit of esp or bas. Under certain driving conditions, where esp or bas would be beneficial, you - if you have not adjusted your driving speeds and stopping in or to account for the lack of the feature, ...

  • Page 262

    32. Compass / mini-trip computer button—if equipped press this button to switch between the different functions. Compass and trip computer — if equipped the compass/trip computer is located in the instru- ment cluster. It features a driver-interactive display (dis- plays information such as outside ...

  • Page 263

    Displayed temperature, therefore temperature readings are not updated when the vehicle is not moving. Press and release the left button (on the instrument cluster) to access the computer displays. Press and hold the left button (on the instrument cluster) for two to three seconds to switch from engl...

  • Page 264

    Trip odometer (odo) / eco (fuel saver indicator) — if equipped this display shows the distance traveled since the last reset. Press and release the right button (on the instru- ment cluster) to switch from odometer, to trip a or trip b, or to eco. Press and hold the right button while the odometer/t...

  • Page 265

    Warning! Even if the display still reads a few degrees above 32°f ( 0°c), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Compass calibration the compass on your vehicle ...

  • Page 266

    Manual compass calibration note: before attempting a manual compass calibra- tion, the engine must be running and the transmission in the park position (if equipped). If the compass appears erratic or inaccurate and the variance has been properly set, you may wish to manu- ally recalibrate the compa...

  • Page 267

    Setting the compass variance refer to the variance map for the correct compass vari- ance zone. To check the variance zone, the ignition must be on. Press and hold the left button (located on the instrument cluster) for approximately 10 seconds to enter the variance mode and release the button when ...

  • Page 268

    Outside temperature if the outside temperature is more than 131°f (55°c), the display will show 131°f (55°c). When the outside tem- perature is less than ⫺40°f (⫺40°c), the display will show ⫺40°f (⫺40°c). Media center 230 (req) — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) note:...

  • Page 269

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Press the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the ...

  • Page 270

    If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect” message will display on the radio screen. Time button press the time button to alternate locations of the time and frequency display. Clock setting procedure 1. Press and hold the ti...

  • Page 271

    Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control...

  • Page 272

    Program type 16-digit character dis- play no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public pub...

  • Page 273

    If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset station. Setup button pressing the setup button allows you to select between the following items: note: turn the tune/scroll control knob to scroll th...

  • Page 274

    • ves™ power - allows you to turn ves™ on and off (if equipped). • ves™ lock - locks out rear ves™ remote controls (if equipped). • ves™ ch1/ch2 - allows the user to change the mode of either the ir1 or ir2 wireless headphones by pressing the audio/select button (if equipped). • set home clock - pre...

  • Page 275

    Subtitle language — if equipped selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙other.⬙ enter the country code using the tune/scroll control knob to s...

  • Page 276

    And press and release that button. If a button is not selected within five seconds after pressing the set but- ton, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: p...

  • Page 277

    Caution! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “disc hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the dvd player and other radio internal components. Note: the ignition switch m...

  • Page 278

    The disc can be ejected with the radio and ignition off. Seek button (cd mode) press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the fi...

  • Page 279

    Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded using formats other than iso 9660 level 1 and level 2, the radio may fail to read files properly and may be unable to play...

  • Page 280

    When using the mp3/wma encoder to compress audio data to an mp3/wma file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (vbr) are also supported. The majority of mp3/wma files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bi...

  • Page 281

    • number of files and folders - loading times will increase with more files and folders to increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button (disc...

  • Page 282

    Pressing the aux button will change the mode to auxil- iary device if the aux jack is connected. Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the devic...

  • Page 283

    Operating instructions - uconnect™ phone (if equipped) refer to “uconnect™ phone” in “understanding the features of your vehicle”. Operating instructions - uconnect™ multimedia (satellite radio) (if equipped) refer to “uconnect™ multimedia (satellite radio)”. Operating instructions - video entertain...

  • Page 284

    The ren, rer and rbz radios contain a cd/dvd player, usb port, and a 30-gigabyte hard drive (hdd). Sirius satellite radio is optional. The 6.5 in (16.5 cm) touch screen allows for easy menu selection. The rer radio also contains a global positioning system (gps)-based navigation system. Refer to you...

  • Page 285

    5. To save the new time setting, touch the screen where the word “save” is displayed. Changing daylight savings time when selected, this feature will display the time of day in daylight savings time. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where th...

  • Page 286

    Want to select, touch the screen where the word “page” is displayed to view additional time zones in the menu. 5. Touch the screen where the word “save” is displayed. Clock setting procedure — rer/ren radio uconnect 威 gps — rer only the gps receiver used in this system is synchronized to the time da...

  • Page 287

    2. Touch the screen where “user clock” is displayed, the clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “daylight savings.” touch the screen where the words “daylight savings” are dis- played to change the current setti...

  • Page 288

    Media center 130 (res) — am/fm stereo radio with cd player (mp3 aux jack) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volum...

  • Page 289

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 290

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 291

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored i...

  • Page 292

    If you insert a disc with the ignition on/run and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player wil...

  • Page 293

    Time button press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff press and hold the ff (fast forward) button and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (reverse) bu...

  • Page 294

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 295

    Rates (vbr) are also supported. The majority of mp3 files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rate. Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio...

  • Page 296

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the dis...

  • Page 297

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 298

    Phone button uconnect™ phone — if equipped press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in “under- standing the features if your vehicle”. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with...

  • Page 299

    Info button press the info button for an rds station (one with call letters displayed). The radio will return a radio text message broadcast from an fm station (fm mode only). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the directi...

  • Page 300

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program for...

  • Page 301

    Program type 16-digit character dis- play soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected ...

  • Page 302

    Window. Select the button (1–6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the set/ rnd button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to e...

  • Page 303

    Inserting compact disc(s) gently insert one cd into the cd player with the cd label facing up. The cd will automatically be pulled into the cd player and the cd icon will illuminate on the radio display. If a cd does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and mu...

  • Page 304

    Note: ejecting with the ignition off is not allowed on convertible or soft-top models (if equipped). Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous se...

  • Page 305

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 306

    Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal cd audio tracks and computer files (including mp3 files). Discs created with an option such as ⬙keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for c...

  • Page 307

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 308

    Press and hold the info button again for three seconds to return to ⬙elapsed time⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or cassette player and utilize the vehicle’s au...

  • Page 309

    Radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www- .Siriuscanada.Ca for ...

  • Page 310

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 311

    Additional three seconds will make the radio display the song title all of the time (press and hold again to return to normal display). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) tu...

  • Page 312

    Set button – to set the pushbutton memory when you are receiving a channel that you wish to commit to pushbutton memory, press the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a butt...

  • Page 313

    System activation sirius satellite radio service is pre-activated and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, includi...

  • Page 314

    Next, turn the knob surrounding the joystick in the center of the radio to scroll to subscription, and then press and release the joystick. All of the esns that apply to your vehicle will display. Selecting uconnect™ multimedia (satellite) mode press the sat button until ⬙sat⬙ appears in the display...

  • Page 315

    Seek buttons press and release the seek buttons to search for the next channel in satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without st...

  • Page 316

    Toggle the music type button again to select the music type. By pressing the seek button when the music type function is active, the radio will be tuned to the next channel with the same selected music type name. If a preset button is activated while in the music type (program type) mode, the music ...

  • Page 317

    You may add a second channel to each pushbutton by repeating the above procedure with this exception: press the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2. This allows a total of 12 satellite channels to be stored into pushbutton memory. Th...

  • Page 318

    6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Note: if you experience difficulty in playing a particu- lar disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have pr...

  • Page 319

    Mode control the mode control allows you to choose from several pat- terns of air distribution as identified by the symbols. Panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-level air is directed through the panel and floor outlet...

  • Page 320

    Defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum fan and temperature settings for best windshield and side window defrosting. Blower control use this control (center rotary knob) to regulate the amount of air forced through the system in any...

  • Page 321

    The instrument panel features four airflow registers. Two registers are located on the outer ends of the instrument panel and two are located in the center of the instrument panel. These registers can be closed to partially block airflow, and they can be adjusted to direct airflow where the occupant...

  • Page 322

    Mix air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Defrost air is directed through the wi...

  • Page 323

    Note: if your air conditioning performance seems lower than expected, check the front of the a/c con- denser: located in front of the radiator, for an accumula- tion of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors...

  • Page 324

    Air conditioning normal operation press this button to engage the air conditioning. A light will illumi- nate when the air conditioning system is engaged. Once the air conditioning is engaged, use a combination of the mode control, fan speed control, and tempera- ture control to achieve your de- sir...

  • Page 325

    Operating tips window fogging windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases turning on the air-conditioning (pressing the snowflake button) will clear the fog. Adjust the temperature...

  • Page 326

    When using the air conditioner in extremely heavy traffic in hot weather especially when towing a trailer, addi- tional engine cooling may be required. If this situation is encountered, operate the transmission in a lower gear to increase engine rpm, coolant flow and fan speed. When stopped in heavy...

  • Page 328: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 331 ▫ manual transmission – if equipped . . . . . . . 331 ▫ automatic transmission – if equipped . . . . . 331 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 331 ▫ extreme cold weather (below –...

  • Page 329

    ▫ automatic transmission with overdrive . . . . 341 䡵 four–wheel drive operation (command- trac i 威 or rock-trac威) — if equipped . . . . . . . 345 ▫ operating instructions/precautions . . . . . . . 345 ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . 347 ▫ shifting procedure . . . . . ....

  • Page 330

    䡵 anti-lock brake system . . . . . . . . . . . . . . . . . 371 䡵 electronic brake control system . . . . . . . . . . . 373 ▫ anti-lock brake system (abs) . . . . . . . . . . . 373 ▫ traction control system (tcs) . . . . . . . . . . . 374 ▫ brake assist system (bas) . . . . . . . . . . . . . . 374 ▫ ...

  • Page 331

    ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . 408 ▫ general information . . . . . . . . . . . . . . . . . . 411 䡵 fuel requirements . . . . . . . . . . . . . . . . . . . . . 411 ▫ reformulated gasoline . . . . . . . . . . . . . . . . 412 ▫ gasoline/oxygenate blends . . . . . . . . . ...

  • Page 332

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Never leave children in the vehicle alone. Leaving unintended children in a vehicle is dangerous for a number of reasons. The child or others could be seri...

  • Page 333

    Turn the ignition switch to the start position and release when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the lock position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Tip start feature – automatic transmission only turn t...

  • Page 334

    Warning! (continued) • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. If the ve...

  • Page 335

    If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accel- erator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. ...

  • Page 336

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is found under the hood bundled in front o...

  • Page 337

    Note: during cold weather, you may experience in- creased effort in shifting until the transmission fluid warms up. This is normal. Shifting fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. You should always use 1st gear when s...

  • Page 338

    Manual transmission shift speeds in mph (km/h) en- gine speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.8l accel. 15 (24) 24 (39) 34 (55) 47 (76) 56 (90) cruise 10 (16) 19 (31) 27 (43) 37 (60) 41 (66) downshifting moving from a high gear down to a lower gear is recommended to preserve brakes when drivin...

  • Page 339

    Maximum recommended downshift speeds caution! Failure to follow the maximum recommended down- shifting speeds may cause the engine to overspeed and/or damage the clutch disc, even if the clutch pedal is pressed. Manual transmission downshift speeds in mph (km/h) gear selec- tion 6 to 5 5 to 4 4 to 3...

  • Page 340

    Automatic transmission — if equipped caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine i...

  • Page 341

    Brake/transmission interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the shift lever in the park position when the ignition switch is in the lock position. To move the shift lever out of the park position, the ignition switch must be turned ...

  • Page 342

    6. Press the shifter release button and shift into neu- tral. 7. The vehicle may then be started in neutral. Have your vehicle inspected by your local authorized dealer if the shift lock manual override has been used. Automatic transmission with overdrive shifting from drive to park or reverse (or f...

  • Page 343

    Gear ranges note: under extreme cold temperatures (-10°f (-23°c) and when in drive, transmission operation may be briefly limited to only second gear operation. Normal operation will resume once the transmission temperature has risen to a suitable level. Do not race the engine when shifting from par...

  • Page 344

    Neutral this range is used when vehicle is standing for pro- longed periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. Note: towing, coasting, or driving the vehicle for any other reason with the shift lever in neutral can result in...

  • Page 345

    Overdrive can be locked out by pressing the o/d off switch located on the center console. The “o/d off indicator light” (on the switch) will illuminate to show that the switch has been activated. When the indicator light is on, overdrive is locked out. Pressing the switch a second time restores the ...

  • Page 346

    Caution! • before moving the shift lever out of park, you must turn the ignition from lock so the steering wheel and shift lever are released. Otherwise, damage to the steering column or shift lever could result. • never race the engine with the brakes on and the vehicle in gear, and never hold the ...

  • Page 347

    • 4l (four-wheel drive low range) the transfer case is intended to be driven in the 2h position for normal street and highway conditions such as hard-surfaced roads. In the event that additional traction is required, the transfer case 4h and 4l positions can be used to lock the front and rear drives...

  • Page 348

    Note: do not attempt to shift when only the front or rear wheels are spinning. The transfer case is not equipped with a synchronizer, and the front and rear driveshaft speeds must be equal for a shift to take place. Shifting while only the front or rear wheels are spinning can cause damage to the tr...

  • Page 349

    4h position this range locks the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed. This range (4h) provides additional traction for loose, slippery road surfaces and should not be used on wet or dry pavement. The “4wd indicator light” (located in the...

  • Page 350

    4h to 4l or 4l to 4h with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission into neutral (n), or press the clutch pedal on a manual transmission. While the vehicle is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position. Do...

  • Page 351

    Trac-lok 威 is especially helpful during slippery driving conditions. With both rear wheels on a slippery surface, a slight application of the accelerator will supply maxi- mum traction. Warning! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the...

  • Page 352

    To activate the system, press the bottom of the axle lock switch once to lock the rear axle only (the “rear axle lock indicator light” will illuminate), press the bottom of the switch again to lock the front axle (the “front axle lock indicator light” will illuminate). When the rear axle is locked, ...

  • Page 353

    The rear axle lock will disengage if the vehicle is taken out of 4l (low) range, or the ignition switch is turned to the lock position. Electronic sway bar disconnect — if equipped your vehicle may be equipped with an electronic discon- necting stabilizer/sway bar. This system allows greater front s...

  • Page 354

    When activation conditions are not met. The stabilizer/ sway bar should remain in on-road mode during normal driving conditions. Warning! Do not disconnect the stabilizer bar and drive on hard-surfaced roads or at speeds above 18 mph (29 km/h); you may lose control of the vehicle, which could result...

  • Page 355

    Warning! If the stabilizer/sway bar will not return to on-road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury. Contact your loca...

  • Page 356

    1. Remove the two nuts from the bodyside. 2. Remove one bolt from the underside of the vehicle. 3. Remove the side step assembly. 5 starting and operating 355.

  • Page 357

    The basics of off-road driving you will encounter many types of terrain driving off- road. You should be familiar with the terrain and area before proceeding. There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice. Every surface has a different ef...

  • Page 358

    Is needed. Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4l (low) range. Simultaneous brake and throttle operation many off-road driving conditions require the simulta- neous use of the brake and throttle (two-footed driving). When climbing rocks, logs, or other stepped obje...

  • Page 359

    Previous vehicles getting stuck. As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck. Sand soft sand is very difficult to travel through with full tire pressure. When crossing sof...

  • Page 360

    Warning! Crossing obstacles can cause abrupt steering system loading which could cause you to loose control of your vehicle. Using a spotter there are many times where it is hard to see the obstacle or determine the correct path. Determining the correct path can be extremely difficult when you are c...

  • Page 361

    Enough to put the vehicle at risk of a rollover. If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires. Use the removed dirt to fill the rut ahead of the turnout you just created. You should now be able to drive out following the trench you...

  • Page 362

    Caution! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Hill climbing hill climbing requires good judgment and a good under- standing of your abilities and your vehicle’s limitations. Hills can cause serious problems. Some are just too steep to climb and sho...

  • Page 363

    Provide a fresh ⬙bite⬙ into the surface and will usually provide enough traction to complete the climb. If you do not make it to the top, place the vehicle in reverse and back straight down the grade using engine resistance along with the vehicle brakes. Warning! Never attempt to climb a hill at an ...

  • Page 364

    Warning! Driving across an incline increases the risk of a rollover, which may result in severe injury. If you stall or begin to lose headway if you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brake. Restart the engine an...

  • Page 365

    Your vehicle’s abilities and be able to recover it if something goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake. If the engine stalls, do not attempt to restart it. Determine if it has ingested water first. The key...

  • Page 366

    Muddy waters; check for hidden obstacles. Make sure you will not be intruding on any wildlife, and you can recover the vehicle if necessary. The key to a safe crossing is the water depth, current and bottom conditions. On soft bottoms, the vehicle will sink in, effectively increasing the water level...

  • Page 367

    The slowest current can push the heaviest vehicle down- stream and out of control if the water is deep enough to push on the large surface area of the vehicle’s body. Before you proceed, determine the speed of the current, the water’s depth, approach angle, bottom condition and if there are any obst...

  • Page 368

    • after extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. ...

  • Page 369

    System. This noise should be considered normal, and it does not in any way damage the steering system. Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the ...

  • Page 370

    If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Parking brake before leaving the vehicle, make sure that the parking...

  • Page 371

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 372

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic transmission in park, a manual transmission in reverse or first gear. Failure to do so may cause the vehicle to roll and cause dam...

  • Page 373

    The anti-lock brake system pump motor runs during the self-test, and during an abs stop, to provide the regulated hydraulic pressure. The motor pump makes a low humming noise during operation; this is normal. Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead t...

  • Page 374

    Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the anti-lock brake system is functioning. Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes...

  • Page 375

    Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) to provide enhanced acceleration and stability. A feature of the tcs system functions similar to a limited slip diff...

  • Page 376

    Warning! The brake assist system (bas) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The bas cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery s...

  • Page 377

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped • vehicle must be on an 8% or greater incline (3% for manual transmission equipped vehicles) • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward...

  • Page 378

    Letting gravity act on the vehicle, as the hsa will prevent the vehicle from rolling. Instead, use the appropriate gear for moving in the desired direction. Towing with hsa hsa will provide assistance when starting on a grade when pulling a trailer. Warning! • if you use a trailer brake controller w...

  • Page 379

    Warning! (continued) • hsa is not a parking brake. If you stop the vehicle on a hill without putting the transmission in park and using the parking brake, it will roll down the hill and could cause a collision with another vehicle or object. Always remember to use the parking brake while parking on ...

  • Page 380

    Speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicle’s speed are sufficient to potentially cause wheel lift, it applies the appropriate brake and may reduce engine power to lessen the chance that wheel lift will occur. Erm will only intervene duri...

  • Page 381

    Counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path. Esp uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match th...

  • Page 382

    Range. Two-wheel drive vehicles and four-wheel drive vehicles in 2h range have two operating modes. 4h range (4wd models) or 2wd models on this is the normal operating mode for esp in 4h and 2wd vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4l range or ...

  • Page 383

    Gravel, it may be desirable to switch to the “partial off” mode by pressing the esp off switch. Once the situation requiring esp to be switched to the “partial off” mode is overcome, turn esp back on by momentarily pressing the esp off switch. This may be done while the vehicle is in motion. Esp off...

  • Page 384

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” esp mode is intended for off-road use only. 4l range (4wd models) es...

  • Page 385

    Warning! With the esp switched off, the enhanced vehicle stability offered by esp and erm are unavailable. In an emergency evasive maneuver, the esp and erm systems will not engage to assist in maintaining stability. The “full off” mode is intended for off- road use only. Disabling esp for modified ...

  • Page 386

    The following procedure will disable (or re-enable) esp functionality in the vehicle: 1. Shift the transfer case into the 4h range position. 2. Turn the steering wheel until it is centered and the wheels are pointed straight ahead. 3. Cycle the ignition key off to on. 4. Wait approximately five seco...

  • Page 387

    If the “esp/bas warning light” comes on continuously with the engine running, a malfunction has been detected in either the esp or the bas system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles/kilometers at speeds greater than 30 mph (...

  • Page 388

    Warning! If tsc activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Tire safety information tire markings 1 — u.S. Dot safety stan- dards code (tin) 4 — maximum load 2 — size designation 5 — maximum pressure 3 — se...

  • Page 389

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 390

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 391

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 392

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 393

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire pressure cold tire inflation pressure is defined as the tire pressure after ...

  • Page 394

    Tire loading and tire pressure tire placard location tire placard location (two-door models) tire placard location (four-door models) 5 starting and operating 393.

  • Page 395

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loa...

  • Page 396

    Combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx kg or xxx lbs” on your vehicle’...

  • Page 397

    396 starting and operating.

  • Page 398

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 399

    Economy improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under-inflation also increases tire rolling resistance and results in higher fuel consumption. R...

  • Page 400

    Tire pressure should be checked and adjusted as well as inspected for signs of tire wear or visible damage, at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated ev...

  • Page 401

    Tire pressures change by approximately 1 psi (7 kpa) per 12° f (7° c) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter. Example: if garage temperature = 68° f (20° c) and the outside temperature = 32° f (0° c) then the cold tire infla...

  • Page 402

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 403

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 404

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep unmounted tires in a cool, dry place with ...

  • Page 405

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 406

    These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on on/off road type tires. Rotation will increase tread life, help to main- tain mud, snow, and wet traction levels, and contribute to a smooth, qu...

  • Page 407

    Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (6.9 kpa) for every 12°f (6.5°c). This means that when the ou...

  • Page 408

    For example, your vehicle may have a recommended cold (parked for more than three hours) air pressure of 35 psi (241 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressure is 30 psi (207 kpa), a temperature drop to 20°f (-7°c) will decrease the tire pressure to approximately ...

  • Page 409

    Note: • the tpms is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat...

  • Page 410

    • tire pressure monitoring telltale light a tire pressure monitoring sensor is located in the spare wheel if the vehicle is equipped with a matching full size spare wheel and tire assembly. The matching full size spare tire can be used in place of any of the four road tires. A low spare tire will no...

  • Page 411

    5. Using wheels/tires not equipped with tpm sensors. Note: • if your vehicle is equipped with a matching full-size spare wheel and tire assembly, it has a tire pressure monitoring sensor, and can be monitored by the tire pressure monitoring system (tpms). In the event that the matching full-size spa...

  • Page 412

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 413

    Over 40 auto manufacturer’s worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) to define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recom- mends the use of gasoline th...

  • Page 414

    E-85 usage in non-flex fuel vehicles non-ffv vehicles are compatible with gasoline contain- ing 10% ethanol (e10). Gasoline with higher ethanol content may void the vehicle’s warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • ...

  • Page 415

    It is even more important to look for gasoline without mmt in canada, because mmt can be used at levels higher than those allowed in the united states. Mmt is prohibited in federal and california- reformulated gasoline. Materials added to fuel all gasoline sold in the united states is required to co...

  • Page 416

    Caution! (continued) • the use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentra- tions of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsi...

  • Page 417

    Warning! (continued) • guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly. Until repaired, drive with all side windows fully open. • keep the swing gate closed when driving your v...

  • Page 418

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light (mil)” to illuminate, due to f...

  • Page 419

    Loose fuel filler cap message after fuel has been added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improperly installed, or damaged. If the system detects a malfunction, the “gascap” message will display in the odometer display. Tighten the gas cap until a...

  • Page 420

    Payload the payload of a vehicle is defined as the allowable load weight a truck or any given vehicle can carry, including the weight of the driver, all passengers, options and cargo. Gross axle weight rating (gawr) the gawr is the maximum permissible load on the front and rear axles. The load must ...

  • Page 421

    Loading the actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. The entire vehicle should first be weighed on a commer- cial scale to ensure that the gvwr has not been ex- ceeded. The ...

  • Page 422

    To maintain warranty coverage, follow the requirements and recommendations in this owner’s manual concern- ing vehicles used for trailer towing. Common towing definitions the following trailer towing-related definitions will as- sist you in understanding the following information: gross vehicle weig...

  • Page 423

    Warning! It is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Trailer tongue weight (tw) the trailer tongue weight is the downward force exerted on the...

  • Page 424

    Weight-distributing hitch a weight-distributing hitch system works by applying leverage through spring (load) bars. It is typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturers’ dir...

  • Page 425

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the trailer towing weights (maximum ...

  • Page 426

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/manual 3.21 two–door x model (4wd) 5,049 lbs (2 290 kg) 25 sq ft (2.32 sq m) 1,000 lbs (453 kg) 100 lbs (45 kg) 3.8l/manual 3.73 two–door x model (4wd) 6...

  • Page 427

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/ automatic 3.73 four–door x model (2wd) 7,734 lbs (3 508 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/ automatic 3.73 four–door sa...

  • Page 428

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/manual 4.10 four–door rubicon model (4wd) 8,248 lbs (3 741 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/ automatic 4.10 four–door ...

  • Page 429

    Consider the following items when computing the weight on the rear axle of the vehicle: • the trailer tongue weight. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weight of the driver and all passengers. Note: remember that everything put into or on the traile...

  • Page 430

    Caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. Thi...

  • Page 431

    Warning! (continued) • vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in park. With a manual transmis- sion, shift the transmission into first gear. And with four-wheel-drive vehicles, make ...

  • Page 432

    − check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “starting and operating” for the proper inspection procedure. − when replacing tires, refer to “tires – general infor- mation” in “starting and operating” for proper tire replacem...

  • Page 433

    Warning! • do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • towing any trailer will increase your stopping distance. When towing, you should allow ...

  • Page 434

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Automatic transmission the drive range can ...

  • Page 435

    The automatic transmission fluid and filter should be changed if you regularly tow a trailer for more than 45 minutes of continuous operation. Refer to “mainte- nance schedule” for the proper maintenance intervals. Note: check the automatic transmission fluid level before towing. O/d off to reduce t...

  • Page 436

    Recreational towing (behind motorhome, etc.) caution! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Two-wheel drive models recreational towing is allowed only if the rear d...

  • Page 437

    Four-wheel drive models note: the transfer case must be shifted into n (neu- tral), automatic transmission must be shifted into park, and manual transmission must be placed in gear (not in neutral) for recreational towing. Shifting into neutral (n) warning! You or others could be injured if you leav...

  • Page 438

    7. Release the brake pedal and ensure that there is no vehicle movement. 8. Turn the engine off and turn the ignition switch to the acc position. 9. Shift the automatic transmission into park. 10. Apply the parking brake. 11. Attach the vehicle to the tow vehicle with the tow bar. 12. Release the pa...

  • Page 439

    3. Shift the transfer case lever into the desired position. 4. Start the engine. 5. Shift the automatic transmission into drive or release the clutch on manual transmissions. Note: when shifting out of transfer case n (neutral) on automatic transmission-equipped vehicles, turning the engine off may ...

  • Page 440: Contents

    What to do in emergencies contents 䡵 hazard warning flasher . . . . . . . . . . . . . . . . 440 䡵 if your engine overheats . . . . . . . . . . . . . . . . 440 䡵 jacking and tire changing . . . . . . . . . . . . . . . 442 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 442 ▫ spare tire ...

  • Page 441

    Hazard warning flasher the hazard warning flasher switch is located on the instrument panel below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. P...

  • Page 442

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 443

    Jacking and tire changing warning! • getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center wh...

  • Page 444

    Spare tire stowage to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (2...

  • Page 445

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • block the wheel diagonally opposite the wheel to...

  • Page 446

    1. Remove the spare tire, jack and tools from the stored location. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 3. Assemble the jack and jacking tools. Connect the jack handle driver to the extension, then to the lug wr...

  • Page 447

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and inst...

  • Page 448

    Pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. Note: when using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. Caution! Do not use a portable battery booster pack or any other boost...

  • Page 449

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 450

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper c...

  • Page 451

    8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle. 10. Reinstall the air intake duct. If frequent jump-starting is required to ...

  • Page 452

    Caution! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. Tow straps are recommended when towing the vehicle, chains may cause vehicle damage. Towing a disabled vehicle the manufac...

  • Page 454: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.8l . . . . . . . . . . . . . 455 䡵 onboard diagnostic system — obd ii . . . . . . 456 ▫ loose fuel filler cap message . . . . . . . . . . . 456 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 455

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 476 ▫ automatic transmission – if equipped . . . . . 478 ▫ hydraulic clutch fluid – manual transmission . . . . . . . . . . . . . . . . . . . . . . . 480 ▫ manual transmission – if equipped . . . . . . . 480 ▫ transfer case – if equipped ....

  • Page 456

    Engine compartment — 3.8l 1 — integrated power module 7 — washer fluid reservoir 2 — battery 8 — engine coolant reservoir 3 — automatic transmission dipstick 9 — air cleaner filter 4 — engine oil fill 10 — coolant pressure cap 5 — engine oil dipstick 11 — power steering fluid reservoir 6 — brake flu...

  • Page 457

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 458

    The message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil off. Emissions inspection and maintenance programs in some localities, it may be a le...

  • Page 459

    A. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m station. B. The mil will not flash at all and will remain fully i...

  • Page 460

    Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If...

  • Page 461

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 462

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to “maintenance schedule” for further information. Note: under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichev...

  • Page 463

    Engine oil viscosity (sae grade) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil fi...

  • Page 464

    Engine oil filter selection all of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably. Only high quality filters should be used to assure most efficient service. Mopar 威 engine ...

  • Page 465

    Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water. R...

  • Page 466

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 467

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency (epa) and is an ozone-saving product. However, the manufacturer recommends that air condi- tioning service be performed by authorized dealers ...

  • Page 468

    Remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may be present with chattering, mark...

  • Page 469

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 470

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions con- trol device and may seriously reduce engine per- formance and cause serious damage to the engine. • damage to the catalytic converter can r...

  • Page 471

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 472

    Garden hose vertically down the face of the a/c con- denser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leak...

  • Page 473

    Caution! • mixing of engine coolant (antifreeze) other than the specified hoat engine coolant (antifreeze) may result in engine damage and may decrease corrosion protection. If a non-hoat engine cool- ant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with ...

  • Page 474

    Please review these recommendations for using hybrid organic additive technology (hoat) engine coolant (antifreeze). When adding engine coolant (antifreeze): • the manufacturer recommends using mopar威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) or equival...

  • Page 475

    Warning! The warning words do not open hot on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the en- gine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To preve...

  • Page 476

    When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine co...

  • Page 477

    • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Brake system in order to assure brake system performan...

  • Page 478

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid ...

  • Page 479

    Warning! (continued) • do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident. Automatic transmission – if equipped selection of lubricant it is important that the proper...

  • Page 480

    To properly check the automatic transmission fluid level, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3. Fully apply the parking brake. 4. Place the shift lever momentarily into each gear posi- ti...

  • Page 481

    7. Check for leaks. Release the parking brake. Note: to prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as lo...

  • Page 482

    Fluid level check check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16 in (4.76 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency of fluid change under normal ope...

  • Page 483

    Caution! When replacing the plugs, do not overtighten them. You could damage them and cause them to leak. Selection of lubricant use only manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Front/rear axle fluid fo...

  • Page 484

    Road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance bui...

  • Page 485

    • avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8...

  • Page 486

    • use mopar威 touch-up paint or equivalent on scratches or chips as soon as possible. Your authorized dealer has touch-up paint to match the color of your vehicle. Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome-plated wheels, should be cleaned regularly with a mil...

  • Page 487

    Caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Glass surfaces all glass surfaces should be cleaned on a regular basis...

  • Page 488

    Replace the belts if they appear frayed or worn or if the buckles do not work properly. Appearance care for fabric top models caution! To maintain the appearance of your vehicle’s interior trim and top, follow these precautions: • avoid leaving your vehicle unattended with the top down, as exposure ...

  • Page 489

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • avoid high-pressure car washes, as they can dam- age the top material. Also, increased water pres- sure may force past the weather strips. • it is recommended that the top be free of wa...

  • Page 490

    Cleaner or equivalent will safely clean all plastic win- dows without scratching. It removes fine scratches to improve visibility and provides uv protection to help prevent yellowing. 2. When washing, never use hot water or anything stronger than a mild soap. Never use solvents such as alcohol or ha...

  • Page 491

    Fuses totally integrated power module the totally integrated power module (tipm) is located in the engine compartment near the battery. This center contains cartridge fuses, mini fuses and relays. A label that identifies each component is printed on the inside of the cover. Cavity cartridge fuse min...

  • Page 492

    Cavity cartridge fuse mini fuse description j9 40 amp green pzev sec motor feed/flex fuel j10 30 amp pink headlamp wash relay/manifold tun- ing valve j11 30 amp pink sway bar j13 60 amp yellow ignition off draw (iod) – main j14 40 amp green ebl (rear window defogger) j15 30 amp pink rear blower j17 ...

  • Page 493

    Cavity cartridge fuse mini fuse description m3 20 amp yellow frt/rear axle locker relay m4 — — m5 — — m6 20 amp yellow power outlet #1/rain sensor m7 20 amp yellow power outlet #2 (batt/acc select) m8 20 amp yellow front heated seat m9 20 amp yellow rear heated seat – if equipped cavity cartridge fu...

  • Page 494

    Cavity cartridge fuse mini fuse description m13 20 amp yellow ignition off draw – cabin compartment node (iod-ccn), wireless control mod- ule (wcm), siren, multifunction control switch (multifctn sw) m14 20 amp yellow trailer tow (export only) cavity cartridge fuse mini fuse description m15 20 amp y...

  • Page 495

    Cavity cartridge fuse mini fuse description m16 10 amp red occupant restraint controller (orc) m17 15 amp blue left tail/license/park lamp (lt-tail/lic/ prk lmp) m18 15 amp blue right tail/park/run lamp (rt-tail/prk/ run lmp) m19 25 amp natural auto shut down (asd #1 and #2) m20 15 amp blue cabin co...

  • Page 496

    Cavity cartridge fuse mini fuse description m30 15 amp blue wiper motor frt, j1962 diagnostic feed m31 20 amp yellow backup lamps (b/u lamps) m32 10 amp red occupant restraint controller (orc), tt europe m33 10 amp red next generation con- troller (ngc), global powertrain engine controller (gpec) ca...

  • Page 497

    Cavity cartridge fuse mini fuse description m38 25 amp natural lock/unlock motors (lock/unlock mtrs) caution! • when installing the integrated power module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrat...

  • Page 498

    • or, disconnect the negative cable from the battery. • anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubricat...

  • Page 499

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamp 1. Open hood and support u...

  • Page 500

    Front park/turn signal 1. Remove the front grille. Turn the retainers along the top 1/4 turn counterclockwise and remove. 2. Pull the bottom of the grille away starting at one side and working toward the other. 3. Turn the socket assembly 1/4 turn counterclockwise and remove from housing. Pull the b...

  • Page 501

    Rear tail, stop, turn signal, and backup lamp 1. Remove the two inboard screws attaching the tail light housing to the body. Do not remove the outer screws at any time. 2. Separate the housing from the body by pushing the lamp inboard while pulling the lamp away from the body. 3. Rotate the appropri...

  • Page 502

    Fluid capacities u.S. Metric fuel (approximate) — two door models 18.5 gallons 70 liters fuel (approximate) — four door models 22.5 gallons 85 liters engine oil with filter 3.8 liter engine 6 quarts 5.7 liters cooling system * 3.8 liter engine (mopar 威 antifreeze/engine coolant 5 year/100,000 mile f...

  • Page 503

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) or equivalent. Engine oil use api certified sae 5w-20 engine oil, meeting the requirements of chrysl...

  • Page 504

    Chassis component fluid, lubricant, or genuine part automatic transmission – if equipped mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Manual transmission – if equipped mopar 威 manual transmission lubricant or equivalent (meeting the re- quirements of chrysler m...

  • Page 506: Maintenance Schedules

    Maintenance schedules contents 䡵 emissions control system maintenance . . . . . . 506 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 506 ▫ required maintenance intervals . . . . . . . . . . 508 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 507

    Emissions control system maintenance the scheduled maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done t...

  • Page 508

    • change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, which- ever comes first. Your dealer will reset the oil change indicator message after completing ...

  • Page 509

    Once a month • check tire pressure and look for unusual wear or damage. • inspect the battery and clean and tighten the terminals as required. • check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and add as needed. • check all lights and other electri...

  • Page 510

    6,000 miles (10,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 12,000 miles (20,000 km) or 12 months maintenance service schedule ❏ change the engine...

  • Page 511

    18,000 miles (30,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front & rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # dea...

  • Page 512

    30,000 miles (50,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the manual transmission fluid if using your veh...

  • Page 513

    36,000 miles (60,000 km) or 36 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings, ...

  • Page 514

    48,000 miles (80,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings, ...

  • Page 515

    60,000 miles (100,000 km) or 60 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect the brake linings, replace if necessary. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ ch...

  • Page 516

    66,000 miles (110,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 72,000 miles (120,000 km) or 72 months maintenance service schedule ❏ change the en...

  • Page 517

    78,000 miles (130,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 84,000 miles (140,000 km) or 84 months maintenance service schedule ❏ change the en...

  • Page 518

    90,000 miles (150,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect and replace pcv valve if necessary.† ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change...

  • Page 519

    96,000 miles (160,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings,...

  • Page 520

    108,000 miles (180,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake lining...

  • Page 521

    120,000 miles (200,000 km) or 120 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace accessory drive belt(s). ❏ inspect the brake linings, replace if necessary. ❏ inspect exhaust system. ❏ inspect the ...

  • Page 522

    126,000 miles (210,000 km) or 126 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front & rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # ...

  • Page 523

    138,000 miles (230,000 km) or 138 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 144,000 miles (240,000 km) or 144 months maintenance service schedule ❏ change th...

  • Page 524

    150,000 miles (250,000 km) or 150 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the manual transmission fluid if using your ...

  • Page 525

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about...

  • Page 526: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527 ▫ prepare for the appointment . . . . . . . . . . . 527 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 527 ▫ be reasonable with r...

  • Page 527

    䡵 publication order forms . . . . . . . . . . . . . . . . 531 䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 533 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 533 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 5...

  • Page 528

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 529

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 530

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 531

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 532

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 533

    Note: a street address is required when ordering manuals (no p.O. Boxes). • service manuals these comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing chrysler group...

  • Page 534

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 535

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 536: Index

    Index 10

  • Page 537

    Abs (anti-lock brake system) . . . . . . . . . . . . 249,371 adding engine coolant (antifreeze) . . . . . . . . . . 472 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 416 air cleaner, engine (engine air cleaner filter) . . . 463 air conditioner maintenance . . . . . . . . . . . . ...

  • Page 538

    Axle lock . . . . . . . . . . . . . . . . . . . . . . . . . . 350,351 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463 keyless transmitter replacement (rke) . . . . . . . 23 belts, seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39,77 body mechanism lubrication ...

  • Page 539

    Child restraint tether anchors . . . . . . . . . . . . . 67,69 child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 climate control . . . . . . . . . . . . . . . . . . . . . . . . . 317 clock . . . . . . . . . . . . . . . . . . . . . 269,283,285,288,297 compact disc (cd) mainten...

  • Page 540

    Disarming, theft system . . . . . . . . . . . . . . . . . . . 18 disposal engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 462 used coolant (antifreeze) . . . . . . . . . . . . . . . . 474 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 doors . . . . . . . . ....

  • Page 541

    Flooded, starting . . . . . . . . . . . . . . . . . . . . . . 332 fuel requirements . . . . . . . . . . . . . . . . . . 411,501 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . 446 oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460,501 oil disposal . . . . . . . . . ....

  • Page 542

    Fluids, lubricants and genuine parts . . . . . . . . . . 502 fog light service . . . . . . . . . . . . . . . . . . . . . . . . 499 fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . 138,499 fold and tumble rear seat . . . . . . . . . . . . . . . . . 130 folding rear seat . . . . . . . . ...

  • Page 543

    Hands-free phone (uconnect™) . . . . . . . . . . . . . . 88 hard top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 hard top, modular . . . . . . . . . . . . . . . . . . . . . . 160 hard top removal . . . . . . . . . . . . . . . . . . . . . . . 168 hazard warning flasher . . . . . . ....

  • Page 544

    Jack location . . . . . . . . . . . . . . . . . . . . . . . . . . . 442 jack operation . . . . . . . . . . . . . . . . . . . . 442,444,445 jacking instructions . . . . . . . . . . . . . . . . . . . . . . 444 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . 446 key, programming . . ....

  • Page 545

    Electronic throttle control warning . . . . . . . . . 260 engine temperature warning . . . . . . . . . . . . . . 250 exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138,499 hazard warning flasher . . . . . . . . . ...

  • Page 546

    Maintenance procedures . . . . . . . . . . . . . . . . . . . 459 maintenance schedule . . . . . . . . . . . . . . . . . . . . 506 malfunction indicator light (check engine) . . 257,457 manual, service . . . . . . . . . . . . . . . . . . . . . . . . . 531 manual transmission . . . . . . . . . . . . ....

  • Page 547

    Oil pressure light . . . . . . . . . . . . . . . . . . . . . . . 247 onboard diagnostic system . . . . . . . . . . . . . . 456,457 operator manual (owner’s manual) . . . . . . . . . . . . 6 outside rearview mirrors . . . . . . . . . . . . . . . . . . 87 overheating, engine . . . . . . . . . . . . . ...

  • Page 548

    Shifting out of transfer case neutral (n) . . . . . 437 reformulated gasoline . . . . . . . . . . . . . . . . . . . . 412 refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466 release, hood . . . . . . . . . . . . . . . . . . . . . . . . . . 135 reminder, lights on . . . . . . . . ...

  • Page 549

    Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 125 easy entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 fold and tumble rea...

  • Page 550

    Cold weather . . . . . . . . . . . . . . . . . . . . . . . . . 332 engine block heater . . . . . . . . . . . . . . . . . . . . 335 engine fails to start . . . . . . . . . . . . . . . . . . . . 332 manual transmission . . . . . . . . . . . . . . . . . . . 331 remote . . . . . . . . . . . . . . . . . ...

  • Page 551

    Pressure monitor system (tpms) . . . . . . . . . . . 406 pressure warning light . . . . . . . . . . . . . . . . . . 252 quality grading . . . . . . . . . . . . . . . . . . . . . . . 533 radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 replacement . . . . . . . . . . . . . . . ....

  • Page 552

    Maintenance . . . . . . . . . . . . . . . . . . . . . . . 478,480 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 range indicator . . . . . . . . . . . . . . . . . . . . . . . 252 shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339 transmitter battery service ...

  • Page 553

    Windshield defroster . . . . . . . . . . . . . . . . . . . . . . 77 windshield washers . . . . . . . . . . . . . . . . . . . 141,467 fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467 windshield wiper blades . . . . . . . . . . . . . . . . . . 466 windshield wipers . . . . . . ....

  • Page 554

    Chrysler group llc 10jk72-126-ac 3rd edition printed in u.S.A..