1. DL manuals
  2. Jeep
  3. Automobile
  4. 2010 Wrangler
  5. Owner's Manual

Jeep 2010 Wrangler Owner's Manual

Summary of 2010 Wrangler

  • Page 1

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 3: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 8 䡵 vehicle ide...

  • Page 4

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle designed for both on-road and off-roa...

  • Page 5

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a warranty information booklet, located on the dvd, and various customer-oriented documents. Please take the ti...

  • Page 6

    Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat b...

  • Page 7

    1 introduction 7.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in an accident or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 9: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 12 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . 13 䡵 steering wheel lock . . . . . . . . . . . . . . . . . . . . 1...

  • Page 10

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . 21 ▫ to turn off “flash lights with lock” . . . . . . . 21 ▫ programming additional transmitters . . . . . . 22 ▫ general information . . . . . . . . . . . . . . . . . . . 22 ▫ transmitter battery replacement . . . . . . . . . . 23 䡵 remote s...

  • Page 11

    ▫ rear center lap/shoulder belt retractor lockout (four-door models only) . . . . . . . . . 44 ▫ adjustable upper shoulder belt anchorage . . . 45 ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . 46 ▫ enhanced seat belt use reminder system (beltalert 威) . . . . . . . . . . . . . . . . . ....

  • Page 12

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 13

    Manual transmission — if equipped 1. Turn the ignition switch to the acc (accessory) position. 2. Push the ignition key inward. 3. Turn the ignition key to the lock position, and remove the key. Warning! Leaving unattended children in a vehicle is danger- ous for a number of reasons. A child or othe...

  • Page 14

    To manually lock the steering wheel with the engine running, rotate the steering wheel one– half revolution from the straight ahead position, turn off the engine, and remove the key. Rotate the steering wheel slightly in both directions until the lock engages. To release the steering wheel lock inse...

  • Page 15

    If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than 10 sec- onds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. Note: the sentry key 威 immobilizer s...

  • Page 16

    Customer key programming if you have two valid sentry keys 威, you can program new sentry keys 威 to the system by performing the following procedure: 1. Cut the additional sentry key 威 transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ign...

  • Page 17

    Reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed. General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cau...

  • Page 18

    To set the alarm the vehicle security alarm will set when you use the remote keyless entry (rke) transmitter to lock the doors and swing gate, or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the vehicle security light (located on the inst...

  • Page 19

    Illuminated entry the interior lights will come on when you open any door. The lights will remain on after all of the doors are closed, and then fade to off or they will immediately fade to off once the ignition switch is turned on. Remote keyless entry (rke) — if equipped this system allows you to ...

  • Page 20

    To unlock the doors and swing gate press and release the rke transmitter unlock button once to unlock the driver’s door only, or twice to unlock all the doors and swing gate. When the rke transmitter unlock button is pressed, the illuminated entry will initiate and the parking lights will flash twic...

  • Page 21

    1. Press the rke transmitter lock button for 4 to 10 seconds. 2. While the lock button is pressed (after four seconds), press the rke transmitter panic button. Release both buttons. The “sound horn on lock” feature can be reactivated by repeating this procedure. Using the panic alarm to turn the pan...

  • Page 22

    Note: pressing the rke transmitter lock button while you are in the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Press the rke transmitter unlock button to deactivate the ve- hicle security alarm. The “flash...

  • Page 23

    Transmitter battery replacement the recommended replacement battery is cr2032. Note: perchlorate material – special handling may apply; see www.Dtsc.Ca.Gov/hazardouswaste/ perchlorate. 1. If the rke transmitter is equipped with a screw, remove the screw. With the rke transmitter buttons facing down,...

  • Page 24

    Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system...

  • Page 25

    To enter remote start press and release the remote start button on the rke transmitter twice, within five sec- onds. The parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the remote start mode for a 15-minute cycle. No...

  • Page 26

    To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, press and release the unlock button on the rke transmitter to unlock the doors and disarm the vehicle security alarm (if equipped). Then, prior to the end of the 15-minute cycle, insert the key into the ignition s...

  • Page 27

    Upper half door window installation — if equipped 1. Grasp the half door window and line up pins into pockets in lower door. 2. Push down to ensure the half door window is fully seated. Front door removal 1. Remove the hinge pin screws from the upper and lower outside hinges (using a #t50 torx 威 hea...

  • Page 28

    Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock the connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected. 3. Unhook the door strap from ...

  • Page 29

    Rear door removal (four-door models) 1. Remove the hinge pin screws from the upper and lower outside hinges (using a #t50 torx 威 head driver). 2. Slide the front seat(s) fully forward. 3. Remove the trim access door from the bottom of b-pillar. 4. Unplug the wiring harness connector. Note: if the re...

  • Page 30

    5. Unhook the door strap from the body hook. 6. With the door open, lift the door to clear hinge pins from their hinges, and remove door. To reinstall the door(s), perform the previous steps in the opposite order. Door locks manual door locks the front (two-door models) and rear doors (four-door mod...

  • Page 31

    Note: the ignition key that is used to start the vehicle is used to lock or unlock the doors, swing gate, and console storage. Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. • never leave chil...

  • Page 32

    Warning! (continued) • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power win- dows, other controls, or move...

  • Page 33

    Note: use the “automatic unlock doors on exit” feature in accordance with local laws. Automatic door locks the doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1. The “automatic door locks” feature is enabled. 2. The transmission is in gear....

  • Page 34

    Windows power windows — if equipped the power window switches are located on the instru- ment panel center stack (below the radio). The top left switch controls the left front window and the top right switch controls the right front window. The lower left switch controls the left rear passenger wind...

  • Page 35

    Console. To disable the window controls, press the win- dow lockout button downward. To enable the window controls, press the window lockout button upward. Auto-down both the driver and front passenger window switches have an “auto-down” feature. Press the window switch past the first detent, releas...

  • Page 36

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down in certain open or partially open posi- tions. This is a normal occurrence and can be minimized by adjusting ...

  • Page 37

    Caution! Do not press on rear wiper blade when closing the rear flip-up window, as damage to the blade will result. Warning! Driving with the flip-up window open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flip-up window clos...

  • Page 38

    Please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible. Warning! In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up. ...

  • Page 39

    Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • ...

  • Page 40

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as fa...

  • Page 41

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your bel...

  • Page 42

    Warning! (continued) • a shoulder belt placed behind will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thighs, b...

  • Page 43

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt cannot do its job as well. In a collision,...

  • Page 44

    Rear center lap/shoulder belt retractor lockout (four-door models only) this feature is designed to lock the retractor whenever the 60% rear seatback is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seatback is not fully latched. Note: • if the...

  • Page 45

    Adjustable upper shoulder belt anchorage in the front seat positions, the shoulder belt anchorage can be adjusted upward or downward to position the belt away from your neck. Push in on the anchorage near your outside shoulder and slide it up or down to reach the position that serves you best. Warni...

  • Page 46

    Seat belt pretensioners the driver and front passenger seat belts are equipped with a pretensioning device that is designed to remove any slack from the seat belt systems in the event of a collision. This device improves the performance of the seat belt by assuring that the belt is tight around the ...

  • Page 47

    1. Turn the ignition switch to the off position, and buckle the driver’s seat belt. 2. Turn the ignition key to the acc/on position (do not start the engine), and wait for the seat belt reminder light to turn off. 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s...

  • Page 48

    Warning! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and stow the seat belt extender when not needed. Supplemental restraint sy...

  • Page 49

    Note: these airbags are certified to the new federal regulations for advanced airbags. The advanced front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on the severity and type of collision. If the vehicle is equipped with side ...

  • Page 50

    Warning! • do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags may no longer be functional. These protective covers for the airbag cushions are designed to open only when the airbags are in...

  • Page 51

    Improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occu- pant protection. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag: 1. Children 12 years and under should always ride buckled up in a rear seat. ...

  • Page 52

    Customer center. Phone numbers are provided under “if you need assistance” in section 9 of this manual. Warning! • relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t depl...

  • Page 53

    How the airbag system works occupant restraint control (orc) module the orc is part of a federally regulated safety system required for this vehicle. The orc determines if deployment of the front and/or side airbags is required in a frontal or side collision. Based on the impact sensors signals, a c...

  • Page 54

    The orc also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the start or on positions. If the key is in the lock position, in the acc position, or not in the ignition, the airbags are not on and will not inflate. The orc contains a backup power supply...

  • Page 55

    Size. The bags fully inflate in about 50 to 70 millisec- onds. This is about half of the time it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger. The driver front airbag gas is vented through the vent holes in the sides of the airbag. ...

  • Page 56

    If a deployment occurs the airbags are designed to deflate immediately after deployment. Note: front and/or side airbags will not deploy in all collisions. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following ...

  • Page 57

    Warning! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioner, and seat belt retractor assem- bly replaced by an authorized dealer as soon as possible. Enhanced accident response system in the event of an impact causing airbag...

  • Page 58

    Warning! (continued) • you need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolsters. • it is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has an ai...

  • Page 59

    In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by chrysler group llc and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle perfor- mance. In addition to crash i...

  • Page 60

    Data parameters that are recorded: • diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system • vehicle speed • engine rpm • brake switch status • pedal position • and other parameters depending on vehicle configuration child restr...

  • Page 61

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any ...

  • Page 62

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • a rearward-facing infant restraint shou...

  • Page 63

    • in the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Inser...

  • Page 64

    Belt-positioning booster seat. The child and belt- positioning booster seat are held in the vehicle by the lap/shoulder belt. Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat wh...

  • Page 65

    In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the rear of the se...

  • Page 66

    Introduced over a period of years, child restraint systems having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat belts. Child restraints having tether straps and hooks for connection to the top tether anchorages, have been available for...

  • Page 67

    If you are installing latch-compatible child restraints in adjacent rear seating positions, you can use the latch anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not latch- compatible, you can...

  • Page 68

    In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch anchorages (four-door models) tether strap mounting (two-door models) 68 things to know before starting your vehicle.

  • Page 69

    Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means for adjusting the tension of the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also b...

  • Page 70

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using th...

  • Page 71

    Route the tether strap over the seatback and attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether under the head rest, and attach the hook to the tether anchor located on the back of the seat. Warning! An incorrectly anchored teth...

  • Page 72

    Engine break-in recommendations a long break-in period is not required for the engine in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration ...

  • Page 73

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), whi...

  • Page 74

    Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, ...

  • Page 75

    Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Periodic safety checks you should make outside the vehicle t...

  • Page 77: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 82 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 83 ▫ vanity mirrors . . . . . . . . . . . . . . . . ...

  • Page 78

    ▫ manual seat height adjustment — if equipped . . . . . . . . . . . . . . . . . . . . . . 119 ▫ front seatback recline . . . . . . . . . . . . . . . . . 119 ▫ front easy entry seats — two door models . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 ▫ head restraints . . . . . . . . . . . . ...

  • Page 79

    䡵 windshield wipers and washers . . . . . . . . . . 135 ▫ windshield wiper operation . . . . . . . . . . . . 135 ▫ intermittent wiper system . . . . . . . . . . . . . . 136 ▫ windshield washers . . . . . . . . . . . . . . . . . . 136 ▫ mist feature . . . . . . . . . . . . . . . . . . . . . . . . 137...

  • Page 80

    ▫ front panel(s) removal . . . . . . . . . . . . . . . . 154 ▫ freedom top™ storage bag . . . . . . . . . . . . . 156 ▫ front panel(s) installation . . . . . . . . . . . . . . 160 ▫ front panel(s) installation with rear hard top removed . . . . . . . . . . . . . . . . . . . . . . . 160 ▫ rear hard t...

  • Page 81

    ▫ closing the sunrider威 . . . . . . . . . . . . . . . . 228 䡵 sunrider威 (four-door models) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . 228 ▫ opening the sunrider威 . . . . . . . . . . . . . . . . 229 ▫ closing the sunrider威 . . . . . . . . . . . . . . . . 231 䡵 folding windshield . ...

  • Page 82

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward...

  • Page 83

    Outside mirrors to receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than the...

  • Page 84

    Vanity mirrors vanity mirrors are located on the sun visors. To use the mirrors, rotate the sun visor down and swing the mirror cover upward. Uconnect™ phone — if equipped uconnect™ phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ phone al- lows you to dial a phon...

  • Page 85

    • www.Jeep.Com/uconnect • or call 1–877–855–8400 uconnect™ phone allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The uconnect™ phone is driven through your bluetooth 威 ...

  • Page 86

    Voice recognition button actual button location may vary with the ra- dio. The individual buttons are described in the “operation” section. The uconnect™ phone can be used with any hands-free profile certified bluetooth 威 cellular phone. See the uconnect™ website for supported phones. If your cellu-...

  • Page 87

    • for each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the combined form voice com- mand ⬙phonebook new entry,⬙ or you can br...

  • Page 88

    The following are general phone to uconnect™ phone pairing instructions: • press the button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙setup phone pairing.⬙ • when prompted, after the beep, say ⬙pair a phone⬙ and follow the audible prompts. • you will be asked to say a four-di...

  • Page 89

    • the system will prompt you to say the number you want to call. • for example, you can say ⬙234-567-8901⬙. • the uconnect™ phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by saying a name • press the button to begin. • after the ⬙read...

  • Page 90

    • when prompted, enter the number designation (e.G., ⬙home,⬙ ⬙work,⬙ ⬙mobile,⬙ or ⬙pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. • when prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry...

  • Page 91

    • depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previous downloaded phonebook is available for use. • only the phonebook of the currently connected cellu- lar phone is accessible. • ...

  • Page 92

    • some phones cannot send phonebook entries if they are already connected to any system via bluetooth 威, and you may see a message on the phone display that the bluetooth 威 link is busy. In this case, the user must first disconnect or drop the bluetooth 威 connection to the uconnect™ phone, and then ...

  • Page 93

    Cellular and a home number, but you can add ”john doe’s” work number later using the ⬙phonebook edit⬙ feature. Delete uconnect™ phonebook entry note: editing phonebook entries is recommended when the vehicle is not in motion. • press the button to begin. • after the ⬙ready⬙ prompt and the following ...

  • Page 94

    • the uconnect™ phone will ask you to verify that you wish to delete all the entries from the phonebook. • after confirmation, the phonebook entries will be deleted. • note that only the phonebook in the current language is deleted. • automatic downloaded phonebook entries cannot be deleted or edite...

  • Page 95

    Answer or reject an incoming call - no call currently in progress when you receive a call on your cellular phone, the uconnect™ phone will interrupt the vehicle audio sys- tem, if on, and will ask if you would like to answer the call. Press the button to accept the call. To reject the call, press an...

  • Page 96

    Toggling between calls if two calls are in progress (one active and one on hold), press the button until you hear a single beep, indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at a time. Conference call when two calls are in progress (o...

  • Page 97

    Call continuation call continuation is the progression of a phone call on the uconnect™ phone after the vehicle ignition key has been switched to off. Call continuation functionality avail- able on the vehicle can be any one of three types: • after the ignition key is switched to off, a call can con...

  • Page 98

    Emergency assistance if you are in an emergency and the cellular phone is reachable: • pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the uconnect™ phone is operational, you may reach the emergency number as follows: • press the button to be...

  • Page 99

    Towing assistance if you need towing assistance: • press the button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙towing assistance.⬙ note: • the towing assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the u.S., 1-877-213-4525 f...

  • Page 100

    When calling a number with your uconnect™ phone that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the button and say the sequence you wish to enter, followed by the word ⬙send.⬙ for example, if required to enter your pin followed with a pound, ...

  • Page 101

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G., the uconnect™ phone will not repeat a phone number before you dial it). • press the button to begin. • after the ⬙ready⬙ prompt and the following beep, say ⬙setup confirmatio...

  • Page 102

    Mute/un-mute (mute off) when you mute the uconnect™ phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect™ phone: • press the button. • following the beep, say ⬙mute.⬙ in order to un-mute th...

  • Page 103

    • when prompted, say ⬙list phones.⬙ • the uconnect™ phone will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “select” or “delete.” also, see the next two sections f...

  • Page 104

    Things you should know about your uconnect™ phone uconnect™ phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect™ tutorial.” voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect™ pho...

  • Page 105

    • speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • make sure that no one other than you is speaking during a voice recognition period. • performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low...

  • Page 106

    • in a convertible vehicle, system performance may be compromised with the convertible top down. Far end audio performance • audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather...

  • Page 107

    3 understanding the features of your vehicle 107.

  • Page 108

    108 understanding the features of your vehicle.

  • Page 109

    3 understanding the features of your vehicle 109.

  • Page 110

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 110 unders...

  • Page 111

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 112

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 113

    If you ever wish to interrupt the system while it lists options, press the button, listen for the beep, and say your command. Pressing the button while the system is speaking is known as “barging in.” the system will be interrupted, and after the beep, you can add or change commands. This will becom...

  • Page 114

    Changing the volume 1. Start a dialogue by pressing the button. 2. Say a command (e.G., “help”). 3. Use the on/off volume rotary knob to adjust the volume to a comfortable level while the voice recogni- tion (vr) system is speaking. Please note the volume setting for vr is different than the audio s...

  • Page 115

    • “radio menu” (to switch to the radio menu) • “main menu” (to switch to the main menu) satellite radio to switch to satellite radio mode, say “sat” or “satellite radio”. In this mode, you may say the following com- mands: • “channel number” (to change the channel by its spoken number) • “next chann...

  • Page 116

    − “continue” (to continue recording) − “delete” (to delete the recording) • “play memos” (to play previously recorded memos) — during the playback you may press the button to stop playing memos. You proceed by saying one of the following commands: − “repeat” (to repeat a memo) − “next” (to play the ...

  • Page 117

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, uconnect™ phone voice training feature may be used. 1. Press the button, say “system setup” and once you are in that menu then say “voice training.” this will train your own voice to the s...

  • Page 118

    Front seat adjustment move the seat forward or rearward by lifting the lever. Release the lever when the seat is in the desired position. Using body pressure, move forward and rearward on the seat to make sure that the latch is fully engaged. Warning! Adjusting a seat while the vehicle is moving is ...

  • Page 119

    Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat. Pull upward on the handle to raise the seat; push downward on the handle to lower the seat. Front seatback recline lean forward befo...

  • Page 120

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seatbelt and be seriously or fatally injured. Use the recliner only when the vehicle is parked. Front easy entry seats — two door models push th...

  • Page 121

    1. To return the seat to a sitting position, rotate the seatback upright until it locks. 2. Push the seat rearward until the track locks. Note: • if equipped with combination lever the seatback will return to its first locked position. The recliner handle will have to be actuated to adjust the seatb...

  • Page 122

    Head restraints head restraints can reduce the risk of injury in the event of a rear impact. The head restraint should be adjusted so the top of the head restraint is located above the top of your ear. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press...

  • Page 123

    To install the head restraint, insert the head restraint rods into each guide, apply pressure down on the headrest until the head restraint reaches the first lock position, push the large button in and push down and adjust head restraint to desired position. Note: ensure that the front of the head r...

  • Page 124

    • be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. 1. Lift the seatback release lever and fold the seatback forward. 2. Slowly flip the entire seat forward. 3. Return the seat to the normal position. 4. Raise the rear seatback ...

  • Page 125

    Removing the rear seat — two door models warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • do not allow people to ride in any area of your vehicle that is n...

  • Page 126

    4. Press down on the release bar on each side, and pull the seat out and away from the lower bracket. 5. Remove the seat from the vehicle. Replacing the rear seat — two door models reverse the steps for removing the seat. Warning! • to help protect against personal injury, passengers should not be s...

  • Page 127

    Note: • prior to folding the rear seat, it may be necessary to reposition the front seat to its mid-track position. • be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. Warning! • it is extremely dangerous to ride in a cargo area...

  • Page 128

    To raise the rear seat raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Note: if the rear seatback is not fully latched, the center shoulder belt will not be ab...

  • Page 129

    Down slightly on the hood before pushing the safety latch. Insert the support rod into the slot on the hood. To close the hood, remove the support rod from the hood panel and place it in the retaining clip. Lower the hood slowly. Secure both of the hood latches. Warning! If the hood is not fully lat...

  • Page 130

    Headlights and parking lights turn the end of the multifunction lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. Note: • lens fogging can occur under certain atmospheric conditions. This will usually clear as atmospheric con...

  • Page 131

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside...

  • Page 132

    Lights-on reminder if the headlights or parking lights are on after the ignition is turned off, a chime will sound when the driver’s door is opened. High/low beam switch push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headligh...

  • Page 133

    Rotate the center portion upward to the last detent to turn on the interior lighting. Daytime running lights — if equipped the headlights come on at a low intensity level after the vehicle has been driven approximately 3 ft (1 m). They will turn off when the vehicle is turned off or when the headlig...

  • Page 134

    Cargo lamp the courtesy and dome lights will turn on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the un- lock button is pressed on the remote keyless entry (rke) transmitter. ...

  • Page 135

    Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located at the end of the lever. For information on using the rear window wiper/ washer, refer to “rear window features” in...

  • Page 136

    Caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. Intermittent wiper ...

  • Page 137

    If the lever is pulled while in the off position, the wipers will operate for as long as the lever is held plus one wipe cycle, then turn off. Mist feature push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down...

  • Page 138

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or...

  • Page 139

    Warning! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. Electronic speed control — if equ...

  • Page 140

    To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To turn the elec- tronic speed control system off, push the on/off button a second time. The cruise indicator light will turn off. The electronic speed control system should be turned off when n...

  • Page 141

    To vary the speed setting when the electronic speed control is set, you can in- crease speed by pushing up and holding the resume accel lever. If the lever is continually held in the resume accel position, the set speed will continue to increase in 5 mph (10 km/h) increments until the lever is relea...

  • Page 142

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use electronic speed control in heavy traffic or on roads that are winding, i...

  • Page 143

    Note: do not exceed the maximum power of 160 watts (13 amps) at 12 volts. The left-side power outlet is powered when the key is in the on or acc positions. The right-side power outlet is powered directly from the battery (power available at all times). Items plugged into this power outlet may discha...

  • Page 144

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 145

    Cupholders front cupholders the front cupholders are located in the center console. Note: the front cupholder insert is removable for cleaning. Rear cupholders the rear cupholders are located on the back of the center console. Front cupholders rear cupholders 3 understanding the features of your veh...

  • Page 146

    Storage console storage compartment to lock or unlock the storage compartment, insert igni- tion the key and turn. To open the storage compartment, press the latch and lift the cover. Rear storage compartment the rear storage compartment cover is held by a spring- loaded latch. In order to remove th...

  • Page 147

    3. Open the rear compartment cover. Dual top — if equipped if your vehicle is equipped with a dual top, you must remove one of the tops from the vehicle. If the soft top is removed, the pivot brackets must also be removed from the sport bar. The soft top was installed at the factory for shipping pur...

  • Page 148

    Removing the soft top 1. Locate and remove the two boxes that contain the following items: • right and left door frames • door frame attachment knobs (four for two-door models, six for four-door models) • right and left quarter windows • rear window • two rear window roll up straps • two sunrider威 s...

  • Page 149

    4. Using a rubber mallet, carefully tap the knuckles from the left and right metal pivot brackets. Remove the soft top from the vehicle and store in a clean, dry location. 5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx 威 head driver. Re...

  • Page 150

    6. Reinstall the hard top. Refer to “freedom top three- piece modular hard top — front/rear panel installa- tion” later in this section. Installing the soft top note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this section. 1. Loca...

  • Page 151

    B. Lay the soft top into the rear of the vehicle with the bows pointing forward and the curved portion of the bows facing upward. C. Tap the knuckles on the side with a rubber mallet to reattach them to the metal pivot brackets. 3 understanding the features of your vehicle 151.

  • Page 152

    D. Screw the pivot screws back into place using a #t30 torx 威 head driver. Secure them until they are snug, being careful not to cross-thread the screws or over- tighten. Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 5. Remove the swing gate bar (black m...

  • Page 153

    Freedom top™ three-piece modular hard top — if equipped caution! • the hard top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus ca...

  • Page 154

    Front panel(s) removal note: left panel must be removed before removing right panel. 1. Fold down the sun visor, and move it to the side. 2. Turn the rear fasteners (knobs) (located on the over- head speaker bar assembly) counterclockwise until they can be removed. 154 understanding the features of ...

  • Page 155

    3. Turn the center l-shaped locks (two) from the center of the roof panel. 4. Turn the rear l-shaped lock (located above the shoul- der belt anchorage). 3 understanding the features of your vehicle 155.

  • Page 156

    5. Unlatch the header panel latch located at the top of the windshield. 6. Remove the left-hand panel. To remove the right panel, follow the steps above except for step 3. Freedom top™ storage bag your vehicle comes with a freedom top™ storage bag that allows you to store your freedom top™ panels. T...

  • Page 157

    Insert the right side freedom panel into the bag with the latches facing downward. Unfold the black panel divider (ensure the divider is laying flat). Secure the velcro, located at the center of the divider. 3 understanding the features of your vehicle 157.

  • Page 158

    Insert the left-side freedom panel into the bag with the latches facing upward. Note: ensure the front freedom panel latch is closed prior to inserting the panel into the bag. Unfold the outer flap and zip the freedom bag closed. 158 understanding the features of your vehicle.

  • Page 159

    Install the seat attachment strap (at the top of the bag) through the loops. Lift the freedom bag into the vehicle with the hooks and straps facing the back of the rear seat. Attach the clips at the bottom of the bag to the child restraint anchorages, located at the base of the rear seat. 3 understa...

  • Page 160

    Wrap the upper strap around the rear head restraints and loop the strap through the buckle. Pull on the strap to tighten the freedom bag securely against the rear seat. Front panel(s) installation note: set the panels on the windshield frame so that there is no overhang. Also, make sure that the pan...

  • Page 161

    Note: the front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there is no overhang. Also, make sure that the panels are sitting flush with the body. 2. Install the right panel first, then the left panel. 3. Reinstall the panel(s) using the sam...

  • Page 162

    5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass. 6. Locate the wire harness on the left rear inside corner of the vehicle. 162 understanding the features of your vehicle.

  • Page 163

    7. Release the red locking tab by pushing upward. 8. To remove the wiring harness press the side tab and pull to disconnect. Note: if necessary, pliers can be used to lightly squeeze grips while disconnecting the washer hose. 3 understanding the features of your vehicle 163.

  • Page 164

    9. To remove the washer hose, pinch the grips on hose connector and pull. 10. Close the swing gate. 11. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage. Rear hard top installation note: if the door frames are installed from soft top usage, they must be re...

  • Page 165

    Door frame warning! Do not drive your vehicle on pavement with the door frame(s) removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only. Caution! Failure to follow these cautions may cause interior water damage, stains or mil...

  • Page 166

    Door frame removal — two-door models 1. Unscrew and remove the door frame attachment knobs (two per side). Warning! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the front of ...

  • Page 167

    4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Warning! Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle. 3 understand...

  • Page 168

    Door frame installation — two-door models 1. Unfold door frame and unscrew thumbscrews. 2. Set the door frame pin into the hole on top of the body side, behind the door opening. 3. After the door frame pin has been set into the body side hole, carefully set the front of the door frame into the rubbe...

  • Page 169

    5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. Door frame removal — four-door models 1. Unscrew and remove the two forward most door frame attachment knobs. Warning! Use both hands to remove the door frames. The door frames will fold and could cause injur...

  • Page 170

    2. Place one hand on the upper rear and one hand on the upper front of the front door frame. 3. Pull the frame toward you with your front hand to remove the frame from the vehicle. 4. Unscrew and remove the remaining door frame at- tachment knob on the rear door frame. 170 understanding the features...

  • Page 171

    5. Place one hand on the upper rear and one hand on the upper front of the rear door frame. Pull the frame toward you with your rear hand to remove the frame from the vehicle. 6. Screw the knob back into the door frame and fold for storage. Store in a secure location. Warning! Never store the door f...

  • Page 172

    Door frame installation — four-door models 1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening. 3. Position the top of the door frame against the metal sport bar and press onto the side bar making sure not to pinch ...

  • Page 173

    5. Carefully set the front of the front door frame in the rubber seal at the top of the windshield. Then, clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched by the door frame. Position the rear of the front door frame to lay on top o...

  • Page 174

    Soft top — two door models please visit the owners section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a struct...

  • Page 175

    Caution! (continued) • refer to “appearance care for fabric top models” in section 7 of this manual. It contains important information on cleaning and caring for your vehi- cle’s fabric top. • do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clips, or retainers securing t...

  • Page 176

    Caution! (continued) • careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle’s interior. • the soft top must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. Quick steps to loweri...

  • Page 177

    2. Release header latches from the windshield frame. 3. Release the sunrider 威 latch (both sides). 3 understanding the features of your vehicle 177.

  • Page 178

    4. Open the swing gate and lower the top. Note: ensure fabric does not overhang the sides of the vehicle. Quick steps to raising the soft top refer to “raising the soft top” in this section for further details. 1. Open the swing gate and raise the top, engaging the sunrider 威 latches (another person...

  • Page 179

    2. Engage header latches. 3 understanding the features of your vehicle 179.

  • Page 180

    3. Install rear corner panels. 4. Install side and back windows. 180 understanding the features of your vehicle.

  • Page 181

    Lowering the soft top 1 — header bow 6 — quarter window 2 — 2–bow 7 — check strap 3 — 3–bow 8 — front retainer — quarter window 4 — sail panel 9 — bottom retainer — quarter window 5 — body side retainer 3 understanding the features of your vehicle 181.

  • Page 182

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 182 understanding the features of your vehicle.

  • Page 183

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 184

    5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across th...

  • Page 185

    6. Undo the velcro 威 that runs along the top and rear edge of the side window. 7. Beginning from the rear lower corner, completely unzip the window. 8. Once unzipped, remove the side window retainers from the door channel and body side channel. Repeat this step on the opposite side. 9. Finish releas...

  • Page 186

    10. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top. 11. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket ba...

  • Page 187

    12. Completely release the latches from the loops on the windshield frame. If your vehicle is not equipped with the sunrider 威 package, proceed to step 15. 13. Make sure the plastic sleeves are slid rearward over the sunrider 威 link (sunrider威 models only). 3 understanding the features of your vehic...

  • Page 188

    14. Unlatch the side bows from both door rails (sun- rider 威 models only). 15. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Move to the front of the vehicle. Grasp the side bow behind the header and lift the top, folding it towa...

  • Page 189

    16. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle. 17. Close the front header latches. 18. Remove the door frames, if desired. Refer to “door frame” in this section. Raising the soft top...

  • Page 190

    4. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow (middle bow) up and over the sports bar until the header rests on the top of the windshield frame. 5. Make sure the sunrider 威 bracket on the side bows latches to the door rails (sunrider 威 models only). 190 understan...

  • Page 191

    6. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 7. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel u...

  • Page 192

    8. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow. 9. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to reac...

  • Page 193

    10. To install the side windows, affix the window tem- porarily by attaching to the velcro 威 in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 11. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on...

  • Page 194

    12. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro 威 along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 195

    13. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 3 understanding the features of your vehicle 195.

  • Page 196

    14. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 15. Run the zipper fully around to the right side of the window. 196 understanding the features of ...

  • Page 197

    16. Grasp the swing gate bar and position it into the swing gate brackets. 17. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel. 18. Close the header latches and return the sun visors to their secu...

  • Page 198

    Soft top (four-door models) please visit the owner’s section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a stru...

  • Page 199

    Caution! (continued) • do not lower the top with the windows installed. Window and top damage may occur. • refer to “appearance care for fabric top models” in section 7 of this manual. It contains important information on cleaning and caring for your vehi- cle’s fabric top. • do not use any tools (s...

  • Page 200

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • it is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle...

  • Page 201

    Quick steps for lowering the soft top 1. Remove the side and back windows. 2. Release header latches from the windshield frame. 3 understanding the features of your vehicle 201.

  • Page 202

    3. Fold header rearward, pulling the fabric to the rear. 202 understanding the features of your vehicle.

  • Page 203

    4. Release sunrider 威 latch (both sides). 5. Open the swing gate and lower the top. Note: ensure the fabric does not overhang the sides of the vehicle. 3 understanding the features of your vehicle 203.

  • Page 204

    Quick steps for raising the soft top 1. Open the swing gate and raise the top, engaging the sunrider 威 latches (another person may be needed to help with this operation). 204 understanding the features of your vehicle.

  • Page 205

    2. Install rear corner panels. 3. Rotate the header forward. 3 understanding the features of your vehicle 205.

  • Page 206

    4. Engage the header latches. 5. Install the side and back windows. 206 understanding the features of your vehicle.

  • Page 207

    Folding down the soft top 1 — header bow 6 — body side retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 3 understanding the features of your vehicle 207.

  • Page 208

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 208 understanding the features of your vehicle.

  • Page 209

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 210

    4. Open the swing gate. 5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull ...

  • Page 211

    6. Undo the velcro 威 that runs along the top and rear edge of the side window. 7. Beginning from the rear lower corner, completely unzip the window. 8. Once unzipped, remove the side window retainers from the door channel and body side channel. Repeat this step on the opposite side. 9. Finish releas...

  • Page 212

    10. Fold the sail panels so that they rest on top of the soft top. 11. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to dis...

  • Page 213

    12. Grasp the front side bow behind the header, and lift the top. 13. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck. 3 understanding the features of your vehicle 213.

  • Page 214

    14. Fold the top so that the material forms a ⬙w⬙ as shown. Enter the vehicle and move the material into two folds. 15. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 214 understanding the ...

  • Page 215

    16. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Grasp the folded side bows and slide the top along the door frame track to the rear door frame. 17. Gently slide the side bows off the door frame track and lower the top down into...

  • Page 216

    19. Once the top is fully down, use the velcro 威 straps provided to secure the top to the vehicle by wrapping the strap around the side bows and through the slot on the body. 20. Close the front header latches. 21. Remove the door frames, if desired. Refer to “door frame” in this section. Putting up...

  • Page 217

    4. Grasp the folded side bows and lift to the top of the rear door frames. Note: help from another person will ease this opera- tion. 5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward. 3 understanding the features of your vehicle 217.

  • Page 218

    6. Ensure that the top locks into the sunrider 威 locking mechanisms that are located above the front of the rear doors. 7. Unclip and move the sun visors to the side. 8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 218 understanding the fe...

  • Page 219

    9. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 10. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel ...

  • Page 220

    11. Ensure that the straps are positioned correctly before pulling the sail panels over the rear roof bow (4–bow). Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (4–...

  • Page 221

    12. To install the side windows, affix the window tem- porarily by attaching it to the velcro 威 in the upper rear corner. Start the zipper but close only about 1 in (2.5 cm). 13. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly posi...

  • Page 222

    14. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro 威 along the top and rear of the window. Repeat this step for the opposite side. 1 ...

  • Page 223

    15. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 3 understanding the features of your vehicle 223.

  • Page 224

    16. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 17. Run the first zipper fully around to the right side of the window. 18. Grasp the swing gate bar...

  • Page 225

    19. Complete the installation of the sail panel by insert- ing the rest of the retainer into the body channel. 20. Close the header latches and return the sun visors to their secured position. Sunrider 姞 (two-door models) — if equipped caution! Operating the top, opening a door or lowering a window ...

  • Page 226

    Opening the sunrider 姞 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Slide the plastic sleeve forward. 226 understanding the features of your vehicle.

  • Page 227

    4. Grasp the header and lift the top back. Make sure the material is folded back as shown. Note: the sunrider 威 latch on the door rail should not be activated for sunrider 威 use. If activated, the soft top must be reinstalled starting from the sail panels. 5. Locate the straps to secure the side bow...

  • Page 228

    Closing the sunrider 姞 1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the front of the vehicle. 4. Hook the header latches to the loops on the wind- shield frame, close latches, and return the sun visors to their origi...

  • Page 229

    Opening the sunrider 姞 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Grasp the front side bow behind the header, and lift the top. 3 understanding the features of your vehicle 229.

  • Page 230

    4. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 5. Fold the top so that the material forms a ⬙w⬙ as shown. Enter the vehicle and move the material into two folds. 230 understanding the features of your vehicle.

  • Page 231

    6. Secure the top by using the two provided straps. Each strap will wrap around the side bow and velcro 威 to itself; use one strap on each side of the vehicle. Closing the sunrider 姞 perform the above steps in the opposite order. Note: failure to fold the fabric rearward will allow the material to s...

  • Page 232

    Raise the windshield and reinstall the side bars as soon as the task that required their removal is completed and before you return to on-road driving. Both you and your passenger should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down...

  • Page 233

    Lowering the windshield and removing side bars 1. Lower the fabric top or remove the hard top following the instructions in this manual. Note: to assist in properly reinstalling side bars, mark the original locations prior to removing. 2. Remove the two top hex bolts (13 mm), and the one side hex bo...

  • Page 234

    Note: pull side bar out horizontally when removing. Caution! Do not remove the head impact foam from the side bars, as damage to the foam may result. Note: store all of the mounting bolts in their original threaded holes and tighten for safekeeping. 5. Remove the side bar assembly, and reattach the ...

  • Page 235

    7. Remove the windshield wiper arms by first pulling the wiper away from the windshield and out to the “lock” position. Unsnap the wiper arm nut caps, and remove the retaining nuts. Lift the wiper arms off and store them in the center console or securely behind the rear seat. Note: it may be necessa...

  • Page 236

    Raising the windshield and replacing side bars 1. Raise the windshield. 2. Loosely attach the rear of the side bar to the sport bar. Refer to step 4 of “lowering windshield and removing side bars” earlier in this section. • reattach the sport bar velcro威 covering. 3. Attach the front of the side bar...

  • Page 237

    4. Tighten all side bar attachment bolts. 5. Install the lower windshield plates with the six black round-headed torx 威 head screws (using a #40 torx威 head driver) on each side of the base of the windshield. 6. Reinstall the wiper arms. Rear window features — hard top only rear window wiper/washer —...

  • Page 238

    Rotate the switch upward to the “on” position will activate the rear wiper. Rotate the switch upward to the “washer” position will activate that rear washer. The washer pump will continue to operate as long as the lever or ring is engaged. Upon release, the wipers will cycle three times before retur...

  • Page 239

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 241: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 244 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 245 䡵 instrument cluster description . . . . . . . . . . . . 246 䡵 compass and trip computer — if equipped . . . . . . . . . . . . ....

  • Page 242

    䡵 sales code (rer/ren) — am/fm/cd/dvd radio – if equipped . . . . . . . . . . . . . . . . . . . . 280 ▫ operating instructions — voice recognition system (vr) — if equipped . . . . . . . . . . . . . 281 ▫ operating instructions — uconnect™ phone — if equipped . . . . . . . . . . . . . . . . . . . . ...

  • Page 243

    ▫ electronic serial number/sirius identification number (esn/sid) . . . . . . . . . 303 ▫ selecting uconnect™ studios (satellite) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304 ▫ satellite antenna . . . . . . . . . . . . . . . . . . . . . 304 ▫ reception quality . . . . . . . . ....

  • Page 244

    Instrument panel features 1 — air outlet 6 — climate controls 2 — instrument cluster 7 — power outlet 3 — horn 8 — lower switch bank 4 — radio 9 — auxiliary power outlet / cigar lighter 5 — glove compartment 244 understanding your instrument panel.

  • Page 245

    Instrument cluster 4 understanding your instrument panel 245.

  • Page 246

    Instrument cluster description 1. Fuel gauge the pointer shows the level of fuel in the fuel tank. Note: when the ignition switch is turned to off, the fuel gauge, voltmeter, oil pressure and temperature gauges may not show accurate readings. When the engine is not running, turn the ignition switch ...

  • Page 247

    6. Front axle lock indicator — if equipped indicates when the front axle lock has been activated. 7. Seat belt reminder light a warning chime and an indicator light will alert you to buckle the seat belts. When the belt is buckled, the chime will stop, but the light will stay on for about six second...

  • Page 248

    11. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake syste...

  • Page 249

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs), are also equipped with el...

  • Page 250

    13. Airbag warning light this indicator lights and remains lit for six to eight seconds when the ignition is first turned on. If the light does not come on for six to eight seconds, stays on or comes on while driving, have the airbag system checked by an authorized dealer. 14. Rear axle lock indicat...

  • Page 251

    Caution! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear continuo...

  • Page 252

    21. Odometer / trip odometer / eco (fuel saver indicator) button press this button to change the display from odometer to either of the two trip odometer settings or the “eco” display. Trip a or trip b will appear when in the trip odometer mode. Press and hold the button for two seconds to reset the...

  • Page 253

    Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped wi...

  • Page 254

    24. Odometer / trip odometer display area the odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “odometer / trip odometer / eco (fuel saver indicator) button” for additional information. U.S. Federal regulations require that upon...

  • Page 255

    The eco display will toggle between eco and eco-on depending on driving habits and vehicle usage. Press the odometer / trip odometer / eco (fuel saver indicator) button to change the display from odometer to either of the two trip odometer settings or the “eco” display. Low tire when the appropriate...

  • Page 256

    12 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to...

  • Page 257

    When the engine is running, the mil may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. Caution! Prolonged driving with the mil on could cause damage to the engine co...

  • Page 258

    Malfunction indicator light ⬙ begins to flash during ac- celeration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. Warning! The electronic stability control (esc) cannot pre- vent the natural laws of ph...

  • Page 259

    Esp or the bas system. If this light stays illuminated, have the esp and bas checked at an authorized dealer as soon as possible. Refer to “electronic brake control system” in section 5 for more information. Warning! If a warning light remains on the system may not be working and you will not have t...

  • Page 260

    31. Compass / mini-trip computer display — if equipped when the appropriate conditions exist, this display shows the mini-trip computer messages. Refer to “mini- trip computer” later in this section. 32. Compass / mini-trip computer button—if equipped press this button to switch between the differen...

  • Page 261

    Reset / change display press and hold the left button (on the instrument cluster) while function is being displayed to reset or change the display. The following trip displays can be reset or changed: • avg eco (changes to present fuel economy) • et (will reset display) trip conditions average fuel ...

  • Page 262

    Eco (fuel saver indicator) — if equipped the eco-on indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify driving habits in order to increase fuel economy. The eco display will toggle between eco and eco-on depending on driving habits and vehicle usage. ...

  • Page 263

    Automatic compass calibration the self-calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions. During a short initial period, the compass may appear erratic and the cal symbol will appear (blinking) on the display. After the vehicle has completed at lea...

  • Page 264

    When the cal symbol is no longer displayed, the compass is calibrated and should display correct head- ings. Verify proper calibration by checking north (n), south (s), east (e), and west (w). If the compass does not appear accurate, repeat the calibration procedure in an- other area. Compass varian...

  • Page 265

    Outside temperature if the outside temperature is more than 131°f (55°c), the display will show 131°f (55°c). When the outside tem- perature is less than ⫺40°f (⫺40°c), the display will show ⫺40°f (⫺40°c). Sales code req — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) note: the rad...

  • Page 266

    Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Press the on/volume control knob a second time to turn off the radio. Electronic volume con...

  • Page 267

    Phone button uconnect™ phone — if equipped press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect” message will display on th...

  • Page 268

    Tune control turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decreas...

  • Page 269

    Toggle the music type button to select the following format types: program type 16-digit character dis- play no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news ne...

  • Page 270

    Station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset station. Setup button pressing the setup bu...

  • Page 271

    Note: • the available selections for each of the above entries varies depending upon the disc. • these selections can only be made while playing a dvd. • ves™ power - allows you to turn ves™ on and off (if equipped). • ves™ lock - locks out rear ves™ remote controls (if equipped). • ves™ ch1/ch2 - a...

  • Page 272

    Subtitle language — if equipped selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙other.⬙ enter the country code using the tune/scroll control knob to s...

  • Page 273

    And press and release that button. If a button is not selected within five seconds after pressing the set but- ton, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: p...

  • Page 274

    Caution! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “disc hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the dvd player and other radio internal components. Note: the ignition switch m...

  • Page 275

    The disc can be ejected with the radio and ignition off. Seek button (cd mode) press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the fi...

  • Page 276

    Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded using formats other than iso 9660 level 1 and level 2, the radio may fail to read files properly and may be unable to play...

  • Page 277

    Frequencies in the following table are supported. In addition, variable bit rates (vbr) are also supported. The majority of mp3/wma files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rates. Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44...

  • Page 278

    • number of files and folders - loading times will increase with more files and folders to increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button (disc...

  • Page 279

    Pressing the aux button will change the mode to auxil- iary device if the aux jack is connected. Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the devic...

  • Page 280

    Operating instructions - uconnect™ studios (satellite radio) (if equipped) refer to “uconnect™ studios (satellite radio)” in this section. Operating instructions - video entertainment system (ves)™ (if equipped) refer to separate “video entertainment system (ves)™ guide.” dolby 威 manufactured under ...

  • Page 281

    Refer to your uconnect™ tunes (ren) or (rer) user’s manual for detailed operating instructions. Operating instructions — voice recognition system (vr) — if equipped for the radio, refer to “voice recognition system (vr)” in section 3. Operating instructions — uconnect™ phone — if equipped refer to “...

  • Page 282

    6. To save the new time setting, touch the screen where the word “save” is displayed. Changing daylight savings time when selected, this feature will display the time of day in daylight savings time. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where th...

  • Page 283

    5. Touch the screen where the word “save” is displayed. Sales code res — am/fm stereo radio with cd player (mp3 aux jack) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on or acc posit...

  • Page 284

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 285

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 286

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored i...

  • Page 287

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 288

    Time button press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff press and hold the ff (fast forward) button and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (reverse) bu...

  • Page 289

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 290

    Rates (vbr) are also supported. The majority of mp3 files use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rate. Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio...

  • Page 291

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the dis...

  • Page 292

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 293

    If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect” message will display on the radio screen. Time button press the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Press and hold the time b...

  • Page 294

    Tune control turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decreas...

  • Page 295

    Program type 16-digit character dis- play no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public pub...

  • Page 296

    Station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset station. Setup button pressing the setup bu...

  • Page 297

    And 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to ...

  • Page 298

    Caution! • this cd player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • res is a single cd player. Do not attempt to insert a second cd if one is alrea...

  • Page 299

    Rw/ff press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am/fm button press the button to select either am or fm mode. Set/rnd button (random play button) press t...

  • Page 300

    • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. With a maximum number of files, exce...

  • Page 301

    Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and...

  • Page 302

    List button (cd mode for mp3 play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that folde...

  • Page 303

    Time button (auxiliary mode) press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is off). Operating instructions - uconnect™ phone (if equipped) refer to “uconnect™ phone” in section 3. Operating instructions - uconnect™ studios (s...

  • Page 304

    2. Your vehicle identification number. To access the esn/sid, refer to the following steps: esn/sid access with req/res radios with the ignition switch in the on/run or acc posi- tion and the radio on, press the setup button and scroll using the tune/scroll control knob until sirius id is selected. ...

  • Page 305

    As possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tre...

  • Page 306

    Info button — except reu radio pressing the info button will cycle the display informa- tion between artist, song title, and composer (if avail- able). Also, pressing and holding the info button for an additional three seconds will make the radio display the song title all of the time (press and hol...

  • Page 307

    Music type button — reu radio pressing this button provides a music type list from which you can make a selection. Once a selection is made, you can seek up or down or scan the channels and the radio will tune to the next station matching the selected format. There is no time-out for this screen. Pr...

  • Page 308

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the channels that you commit to pushbutton memory (12 satellite stations). Operating instructions — uconnect™ phone (if equipped) refer to “uconnect™ phone” in section 3. Ope...

  • Page 309

    Radio operation and cellular phones under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your...

  • Page 310

    Mode control the mode control allows you to choose from several pat- terns of air distribution as identified by the symbols. Panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Bi-level air is directed through the panel and floor outlet...

  • Page 311

    Blower control use this control (center rotary knob) to regulate the amount of air forced through the system in any mode you select. The fan speed increases as you move the control to the right from the off position. Note: for vehicles equipped with remote start, the climate controls will not functi...

  • Page 312

    The instrument panel features four airflow registers. Two registers are located on the outer ends of the instrument panel and two are located in the center of the instrument panel. These registers can be closed to partially block airflow, and they can be adjusted to direct airflow where the occupant...

  • Page 313

    Mix air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Defrost air is directed through the wi...

  • Page 314

    Note: if your air conditioning performance seems lower than expected, check the front of the a/c con- denser: located in front of the radiator, for an accumula- tion of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors...

  • Page 315

    Air conditioning normal operation press this button to engage the air conditioning. A light will illumi- nate when the air conditioning system is engaged. Once the air conditioning is engaged, use a combination of the mode control, fan speed control, and tempera- ture control to achieve your de- sir...

  • Page 316

    Operating tips window fogging windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases turning on the air-conditioning (pressing the snowflake button) will clear the fog. Adjust the temperature...

  • Page 317

    Winter operation when operating the system during the winter months, make sure the air intake, located directly in front of the windshield, is free of ice, slush, snow, or other obstructions. Vacation storage anytime you store your vehicle or keep it out of service (i.E., vacation) for two weeks or ...

  • Page 319: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 323 ▫ manual transmission . . . . . . . . . . . . . . . . . 323 ▫ automatic transmission . . . . . . . . . . . . . . . 323 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 323 ▫ extreme cold weat...

  • Page 320

    ▫ automatic transmission with overdrive . . . . 333 䡵 four–wheel drive operation (command-trac i威 or rock-trac 威) — if equipped . . . . . . . . . . . . . 337 ▫ operating instructions/precautions . . . . . . . 337 ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . 339 ▫ shifting procedure ...

  • Page 321

    䡵 anti-lock brake system . . . . . . . . . . . . . . . . . 362 䡵 electronic brake control system . . . . . . . . . . . 364 ▫ anti-lock brake system (abs) . . . . . . . . . . . 364 ▫ traction control system (tcs) . . . . . . . . . . . 365 ▫ brake assist system (bas) . . . . . . . . . . . . . . 365 ▫ ...

  • Page 322

    ▫ general information . . . . . . . . . . . . . . . . . . 400 䡵 fuel requirements . . . . . . . . . . . . . . . . . . . . . 401 ▫ reformulated gasoline . . . . . . . . . . . . . . . . 401 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . 402 ▫ e-85 usage in non-flex fuel vehicles . . . . . . 402...

  • Page 323

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Do not leave children or animals inside parked vehicles in hot weather. Interior heat buildup may cause serious injury or death. Manual transmission apply ...

  • Page 324

    Tip start feature — automatic transmission only turn the ignition switch to the start position and release it as soon as the starter engages. The starter motor will continue to run, but will automatically disengage itself when the engine is running. If the engine fails to start, the starter will dis...

  • Page 325

    Warning! (continued) • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. If the ve...

  • Page 326

    If the engine shows no sign of starting after two 15– second periods of cranking with the accelerator pedal held to the floor, repeat the “normal starting” or “ex- treme cold weather” procedures. With tip start — automatic transmission only if the engine fails to start after you have followed the “n...

  • Page 327

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is found under the hood bundled in front o...

  • Page 328

    Note: during cold weather, you may experience in- creased effort in shifting until the transmission fluid warms up. This is normal. Shifting fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. You should always use 1st gear when s...

  • Page 329

    Manual transmission shift speeds in mph (km/h) en- gine speeds 1 to 2 2 to 3 3 to 4 4 to 5 5 to 6 3.8l accel. 15 (24) 24 (39) 34 (55) 47 (76) 56 (90) cruise 10 (16) 19 (31) 27 (43) 37 (60) 41 (66) downshifting moving from a high gear down to a lower gear is recommended to preserve brakes when drivin...

  • Page 330

    Maximum recommended downshift speeds caution! Failure to follow the maximum recommended down- shifting speeds may cause the engine to overspeed and/or damage the clutch disc, even if the clutch pedal is pressed. Manual transmission downshift speeds in mph (km/h) gear selec- tion 6 to 5 5 to 4 4 to 3...

  • Page 331

    Automatic transmission — if equipped caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine i...

  • Page 332

    Brake/transmission interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the shift lever in the park position when the ignition switch is in the lock position. To move the shift lever out of the park position, the ignition switch must be turned ...

  • Page 333

    6. Press the shifter release button and shift into neu- tral. 7. The vehicle may then be started in neutral. Have your vehicle inspected by your local authorized dealer if the shift lock manual override has been used. Automatic transmission with overdrive shifting from drive to park or reverse (or f...

  • Page 334

    Do not race the engine when shifting from park or neutral position into another gear range. Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use park while the vehicle is in motion. Apply the parking brake when leaving the vehi...

  • Page 335

    Note: towing, coasting, or driving the vehicle for any other reason with the shift lever in neutral can result in severe transmission damage. Refer to “recreational towing” in section 5 and “towing a disabled vehicle” in section 6 of this manual. Overdrive this range is used for most city and highwa...

  • Page 336

    Overdrive can be locked out by pressing the o/d off switch located on the center console. The “o/d off indicator light” (on the switch) will illuminate to show that the switch has been activated. When the indicator light is on, overdrive is locked out. Pressing the switch a second time restores the ...

  • Page 337

    Torque converter clutch a feature designed to improve fuel economy has been added to the automatic transmission of this vehicle. A clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly differ- ent feeling or response during normal operation in h...

  • Page 338

    Rear wheels to rotate at the same speed. This is accom- plished by simply moving the shift lever to one of these positions. The 4h and 4l positions are intended for loose, slippery road surfaces only and not intended for normal driving. Driving in the 4h and 4l positions on hard- surfaced roads will...

  • Page 339

    Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first fully engaging the parking brake. The transfer case n (neutral) position disengages both the front and rear driveshaft from the powertrain, and will allow the ...

  • Page 340

    Speed. This range (4l) provides additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). The “4wd indicator light” (located in the instrument cluster) will illuminate when the transfer case is shifted into the 4l position. Shifting procedu...

  • Page 341

    Warning! Failure to engage a position completely can cause transfer case damage or loss of power and vehicle control. You could have an injury accident. Do not drive the vehicle unless the transfer case is fully engaged. Trac-lok 姞 rear axle — if equipped the trac-lok 威 rear axle provides a constant...

  • Page 342

    Axle lock (tru–lok 姞 ) — rubicon models the axle lock switch is located on the lower switch bank (below the climate controls). This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should be 10 mph (16 km/h) or less. To...

  • Page 343

    Rear axle lock (four-wheel drive non-rubicon models) — if equipped the rear axle lock switch is located on the lower switch bank (below the climate controls). This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should...

  • Page 344

    Press the sway bar switch to activate the system. Press the switch again to deactivate the system. The “sway bar indicator light” (located in the instrument cluster) will illuminate when the bar is disconnected. The “sway bar indicator light” will flash during activation transition, or when activati...

  • Page 345

    To disconnect the stabilizer/sway bar, shift to either 4h or 4l (refer to “four-wheel drive operation” in this section) and press the sway bar switch to obtain the off-road position. The “sway bar indicator light” will flash until the stabilizer/sway bar has been fully discon- nected. Note: the stab...

  • Page 346

    An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfacto- rily in off-road cond...

  • Page 347

    3. Remove the side step assembly. The basics of off-road driving you will encounter many types of terrain driving off- road. You should be familiar with the terrain and area before proceeding. There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice...

  • Page 348

    Warning! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When to use 4l (low) range when off-road driving, shift into 4l (low) for additional traction and control on slippery or difficult terrain, ascending or descending steep hi...

  • Page 349

    Caution! On icy or slippery roads, do not downshift at high engine rpm or vehicle speeds, because engine brak- ing may cause skidding and loss of control. Mud deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use second gear (manual transmissi...

  • Page 350

    Caution! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneu- vers. Crossing obstacles (rocks and other high points) while driving off-road, you...

  • Page 351

    The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse. Always look ahead and make every effort to cross the large rocks with your tires. Caution! • never attempt to straddle a rock that is large enough to strike your axles or undercarriage. • never attempt...

  • Page 352

    Caution! Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high-centered. Getting high-centered if you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is c...

  • Page 353

    Recover the vehicle if something goes wrong? If every- thing looks good and you feel confident, shift the trans- mission into a lower gear with 4l (low) engaged, and proceed with caution, maintaining your momentum as you climb the hill. Driving up hill once you have determined your ability to procee...

  • Page 354

    Confident in your ability to proceed, then make sure you are in 4l (low) and proceed with caution. Allow engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock. Warning! Do not descend a steep grade in neutral. Use vehicle brakes in conjunction ...

  • Page 355

    Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in reverse gear. Never back dow...

  • Page 356

    Caution! • water ingestion into the axles, transmission, trans- fer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or...

  • Page 357

    Vehicle recovery. If you are able to determine you can safely cross, than proceed using the low and slow method. Caution! Muddy waters can reduce the cooling system effec- tiveness by depositing debris onto the radiator. Crossing ditches, streams, shallow rivers or other flowing water flowing water ...

  • Page 358

    Always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiato...

  • Page 359

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 360

    Checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an autho- rized dealer. Caution! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering compon...

  • Page 361

    Note: the instrument cluster “brake warning light” indicates only that the parking brake is applied. You must be sure the parking brake is fully applied before leaving the vehicle. Be sure the parking brake is firmly set when parked, and the shift lever is in the park position (automatic trans- miss...

  • Page 362

    Warning! (continued) • never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power win- dows, other controls, or move...

  • Page 363

    The anti-lock brake system pump motor runs during the self-test, and during an abs stop, to provide the regulated hydraulic pressure. The motor pump makes a low humming noise during operation; this is normal. During off-road use, loss of traction can temporarily defeat the system and cause the warni...

  • Page 364

    Caution! The anti-lock brake system is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or tele- phones. Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indic...

  • Page 365

    Warning! The anti-lock brake system (abs) cannot prevent the natural laws of physics from acting on the ve- hicle, nor can they increase the traction afforded by prevailing road conditions. The abs cannot prevent accidents, including those resulting from excessive speed in turns, driving on very sli...

  • Page 366

    Benefit of the system, you must apply continuous brak- ing pressure during the stopping sequence. Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the bas is deactivated. Warning! The brake assist system (bas) cannot prevent the natural laws o...

  • Page 367

    Warning! If the clutch pedal (manual transmission only) re- mains pressed during the application of the throttle, the hsa will disengage allowing the vehicle to roll down the incline. This could cause a collision with another vehicle or object. To avoid this, do not apply throttle while pressing the...

  • Page 368

    Hsa on automatic transmission vehicles the system will work in reverse, and all forward gears on vehicles equipped with an automatic transmission. The system will not activate if the vehicle is placed in neutral. Hsa on manual transmission vehicles the system will work in reverse, forward gears, and...

  • Page 369

    Warning! (continued) • hsa is not a parking brake. If you stop the vehicle on a hill without putting the transmission in park and using the parking brake, it will roll down the hill and could cause a collision with another vehicle or object. Always remember to use the parking brake while parking on ...

  • Page 370

    Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicle’s speed are sufficient to potentially cause wheel li...

  • Page 371

    Counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path. Esc uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match th...

  • Page 372

    Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent acci- dents, including those resulting from excessive speed in turns, driving on very s...

  • Page 373

    The esc system has three available operating modes in 4h range. The system has one operating mode in 4l range. Two-wheel drive vehicles and four-wheel drive vehicles in 2h range have two operating modes. 4h range (four-wheel drive models) or two-wheel drive models on this is the normal operating mod...

  • Page 374

    Esc off (4h range only) this mode is intended for off-highway or off-road use when esc stability features could inhibit vehicle maneu- verability due to trail conditions. This mode is entered by pressing and holding the “esc off” switch for five seconds when the vehicle is stopped and the engine is ...

  • Page 375

    4l range (four-wheel drive models) esc off this is the normal operating mode for esc in 4l range. Whenever the vehicle is started in 4l range, or the transfer case (if equipped) is shifted from 4h range or neutral to 4l range, the esc system will be in this mode. In 4l range, esc and tcs, except for...

  • Page 376

    Disabling esc for modified vehicles (four-wheel drive models only) vehicles modified with larger tires and/or suspension lifts may experience early esc activations as compared to a non-modified production vehicle depending on lift size, tire size, suspension changes and/or driving habits. If early e...

  • Page 377

    2. Turn the steering wheel until it is centered and the wheels are pointed straight ahead. 3. Cycle the ignition key off to on. 4. Wait approximately five seconds for the system bulb check. 5. Turn and hold the steering wheel one-half turn to the right (clockwise). 6. Press and hold the “esc off” bu...

  • Page 378

    Follow the tongue weight recommendations. Refer to “trailer towing” in section 5 of this manual for more information on towing a trailer with your vehicle. When tsc is functioning, the “esc malfunction indicator light” will flash, the engine power may be reduced and you may feel the brakes being app...

  • Page 379

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 380

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t = temporary spare tire 31 = overall diameter in inches (in) 215 = sec...

  • Page 381

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 382

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 383

    Tire loading and tire pressure tire placard location tire placard location (two-door models) tire placard location (four-door models) 5 starting and operating 383.

  • Page 384

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loa...

  • Page 385

    Combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx kg or xxx lbs” on your vehicle’...

  • Page 386

    386 starting and operating.

  • Page 387

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 388

    Economy improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under-inflation also increases tire rolling resistance and results in higher fuel consumption. R...

  • Page 389

    Tire pressure should be checked and adjusted as well as inspected for signs of tire wear or visible damage, at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated ev...

  • Page 390

    Tire pressures change by approximately 1 psi (7 kpa) per 12° f (7° c) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter. Example: if garage temperature = 68° f (20° c) and the outside temperature = 32° f (0° c) then the cold tire infla...

  • Page 391

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 392

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Life of tire the service life of a tire is dependent upon varying factors includi...

  • Page 393

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance wh...

  • Page 394

    Warning! (continued) • failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire chains instal...

  • Page 395

    Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be reduced by timely rotation ...

  • Page 396

    The tire pressure will vary with temperature by about 1 psi (6.9 kpa) for every 12°f (6.5°c). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after ...

  • Page 397

    May cause the tire pressure to rise to approximately 30 psi (207 kpa), but the “tire pressure monitoring telltale light” will still be on. In this situation, the “tire pressure monitoring telltale light” will turn off only after the tires have been inflated to the vehicle’s recom- mended cold placar...

  • Page 398

    • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the “tire pressure monitoring telltale light.” • seasonal temperature changes will affec...

  • Page 399

    Inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value. The system will automatically update and the “tire pressure monitoring telltale light” will extinguish once the updated tire pressures have been received. The vehicle may ...

  • Page 400

    Off the “tire pressure monitoring telltale light” as long as none of the road tires are below the low pressure warning threshold. • if your vehicle is not equipped with a matching full-size spare wheel and tire assembly, it does not have a tire pressure monitoring sensor in the spare tire. The tpms ...

  • Page 401

    The tire pressure sensors are covered under one of the following licenses: united states . . . . . . . . . . . . . . . . . . . . . Kr5s120123 canada . . . . . . . . . . . . . . . . . . . . . . . . 2671-s120123 fuel requirements all engines are designed to meet all emis- sions regulations and provide...

  • Page 402

    The manufacturer supports the use of reformulated gaso- line. Properly blended reformulated gasoline will pro- vide excellent performance and durability for the engine and fuel system components. Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% etha...

  • Page 403

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory more extensive repairs will be required for prolo...

  • Page 404

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by fed- eral law. Using leaded gasoline can impair engine performance, and damage the emission control system. • an out-of-tune engine, or certain fuel or ignition...

  • Page 405

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such ...

  • Page 406

    Adding fuel fuel filler cap (gas cap) the gas cap is located on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle. Caution! • damage to the fuel system or emission control system could result from using an improper fu...

  • Page 407

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and will cause the mil to turn on. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place ga...

  • Page 408

    This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle weight rating (gawr) front and rear, and vehicle identification number (vin). A month-day-hour (mdh) number is included on this label and indicates the month, day, and hour of manufacture. The bar c...

  • Page 409

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 410

    Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in t...

  • Page 411

    Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Note: the gcwr rating includes a 150 lbs (68 kg) allowance for the presence of a driver. Gross axle weight rating (gawr) the gawr is the maximum capacity of the fr...

  • Page 412

    Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. This kind of hitch is the most popular on the market today and is commonly used to tow small and medium-sized trailers. ...

  • Page 413

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the trailer towing weights (maximum ...

  • Page 414

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8...

  • Page 415

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/ automatic 3.73 two–door sa- hara model (4wd) 6,233 lbs (2 827 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.8l/manual 4.10 2–door rubi- ...

  • Page 416

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/manual 3.21 four–door x model (4wd) 5,431 lbs (2 463 kg) 32 sq ft (2.97 sq m) 1,000 lbs (453 kg) 100 lbs (45 kg) 3.8l/manual 3.73 four–door x model (4wd)...

  • Page 417

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.8l/ automatic 3.73 four–door sahara model (4wd) 8,127 lbs (3 686 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.8l/manual 4.10 four–door r...

  • Page 418

    Which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents. Consider the following items when computing the weight on the rear axle of the vehicle: • the trailer tongue weight. • the weight of any other type of cargo or e...

  • Page 419

    Note: trailer towing requires special rear axle lubri- cant. Refer to “fluids, lubricants, and genuine parts” in section 7 for the correct fluid type. Caution! • avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may dam- age your vehicle. Warning! Improper towing...

  • Page 420

    Warning! (continued) • vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in park. With a manual transmis- sion, shift the transmission into first gear. And with four-wheel-drive vehicles, make ...

  • Page 421

    − check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires–general infor- mation” in this section for the proper inspection pro- cedure. − when replacing tires, refer to “tires–general informa- tion” in this section for proper tire replacement proce- dures. Replac...

  • Page 422

    Warning! • do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • towing any trailer will increase your stopping distance. When towing, you should allow ...

  • Page 423

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Automatic transmission the drive range can ...

  • Page 424

    The automatic transmission fluid and filter should be changed if you regularly tow a trailer for more than 45 minutes of continuous operation. Refer to the “main- tenance schedule” in section 8 for the proper mainte- nance intervals. Note: check the automatic transmission fluid level before towing. ...

  • Page 425

    Recreational towing (behind motorhome, etc.) caution! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Towing – two-wheel drive models recreational towing is allowed only if t...

  • Page 426

    Use the following procedure to prepare your vehicle for recreational towing. Caution! It is necessary to follow these steps to be certain that the transfer case is fully in n (neutral) before recre- ational towing to prevent damage to internal parts. 1. Turn the engine off. 2. Press the brake pedal....

  • Page 427

    Caution! Damage to the transmission may occur if the trans- mission is shifted into park with the transfer case in n (neutral) and the engine running. With the trans- fer case in n (neutral) ensure that the engine is off prior to shifting the transmission into park (refer to steps 8 – 9 above). Shif...

  • Page 429: Contents

    What to do in emergencies contents 䡵 hazard warning flasher . . . . . . . . . . . . . . . . 430 䡵 if your engine overheats . . . . . . . . . . . . . . . . 430 䡵 jacking and tire changing . . . . . . . . . . . . . . . 431 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 432 ▫ spare tire ...

  • Page 430

    Hazard warning flasher the hazard warning flasher switch is located on the lower switch bank below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 431

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 432

    Jack location the jack and lug wrench are located in the rear storage compartment. Refer to “storage” in section 3 of this manual. Spare tire stowage to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwi...

  • Page 433

    2. Set the parking brake. 3. Shift the automatic transmission into park, or a manual transmission into reverse. 4. Turn the ignition to lock. 5. Turn on the hazard warning flasher. 6. Block both the front and rear of the wheel diagonally opposite of the jack- ing position. For example, if changing t...

  • Page 434

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. • only use the jack in the positions indicated and for lifting this vehicle during a tire change. • if working on or near a roadway, be extremely careful of motor tr...

  • Page 435

    5. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. Warning! Raising the vehicle higher than necessary can make the vehicle...

  • Page 436

    Wheel nut tightness is 95 ft lbs (130 n·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Remove the jack assembly and wheel blocks. Warning! A loose tire or jack, thrown forward in a collision or hard stop, cou...

  • Page 437

    1. Remove all metal jewelry such as watch bands or bracelets which might make an unintended electrical contact. 2. Park the booster vehicle within cable reach but with- out letting the vehicles touch. Set the parking brake on both vehicles, shift the automatic transmission into park, or the manual t...

  • Page 438

    Warning! Any procedure other than above could result in: • personal injury caused by electrolyte squirting out the battery vent. • personal injury or property damage due to battery explosion. • damage to the charging system of the booster vehicle or of the immobilized vehicle. • you should not try t...

  • Page 439

    Warning! • chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. Caution! Tow hooks are for emergency use only, to rescue a vehicle str...

  • Page 441: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment – 3.8l . . . . . . . . . . . . . . 443 䡵 onboard diagnostic system — obd ii . . . . . . 444 ▫ loose fuel filler cap message . . . . . . . . . . . 444 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 442

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 463 ▫ automatic transmission — if equipped . . . . 465 ▫ hydraulic clutch fluid — manual transmission . . . . . . . . . . . . . . . . . . . . . . . 468 ▫ manual transmission — if equipped . . . . . . 468 ▫ transfer case — if equipped . . ....

  • Page 443

    Engine compartment – 3.8l 1 — integrated power module 7 — washer fluid reservoir 2 — battery 8 — engine coolant reservoir 3 — automatic transmission dipstick 9 — air cleaner filter 4 — engine oil fill 10 — coolant pressure cap 5 — engine oil dipstick 11 — power steering fluid reservoir 6 — brake flu...

  • Page 444

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 445

    The message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil off. Emissions inspection and maintenance programs in some localities, it may be a le...

  • Page 446

    5. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 447

    Your vehicle. Refer to these manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Onl...

  • Page 448

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 449

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” in section 8 for information on this system. Note: under no circumstances should oil change intervals exceed 6,000 miles (10 000 km...

  • Page 450

    Engine oil viscosity (sae grade) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil fi...

  • Page 451

    Engine oil filter selection all of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably. Only high quality filters should be used to assure most efficient service. Mopar 威 engine ...

  • Page 452

    Caution! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and are identified on the battery case. Also, if a “fast charger”...

  • Page 453

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 454

    Wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating, excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other under...

  • Page 455

    Check the fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (not radiator anti- freeze). When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades; this will help blade perfor- mance. To p...

  • Page 456

    Caution! The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- ness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. Under normal operating conditions, the catalyti...

  • Page 457

    Warning! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situati...

  • Page 458

    Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiat...

  • Page 459

    Cooling system — drain, flush, and refill if the engine coolant (antifreeze) is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant ...

  • Page 460

    Caution! (continued) • this vehicle has not been designed for use with propylene glycol based engine coolant (anti- freeze). Use of propylene glycol base engine cool- ant (antifreeze) is not recommended. Adding engine coolant your vehicle has been built with an improved engine coolant (antifreeze) t...

  • Page 461

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze...

  • Page 462

    To remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Engine coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling, and war...

  • Page 463

    Engine coolant (antifreeze) needs to be added, the contents of the coolant recovery bottle must also be protected against freezing. • if frequent engine coolant (antifreeze) additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should ...

  • Page 464

    Power disc brakes disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material. Brake master cylinder the fluid level in the master cylinders should be checked whenever the vehicle is serviced. If ...

  • Page 465

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 466

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter change...

  • Page 467

    Adding any quantity of oil through the dipstick tube, wait a minimum of two minutes for the oil to fully drain into the transmission before rechecking the fluid level. Note: if it is necessary to check the transmission below the operating temperature, the fluid level should be between the two cold (...

  • Page 468

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Hydraulic clutch fluid — manual transmission the clutch hydraulic system is a sealed maintenance-free system. In the e...

  • Page 469

    Transfer case — if equipped fluid level check the fluid level should be to the bottom edge of the fill hole (a) when the vehicle is in a level position. Adding fluid fluid should be added only at filler hole until fluid begins to run out of the hole. Drain first remove the fill plug (b), then the dr...

  • Page 470

    Adding fluid add lubricant only at the fill hole and only to the level specified above. Selection of lubricant use only manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in this section for the correct fluid type. Maintenance after off-road driving after extended ope...

  • Page 471

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons,...

  • Page 472

    • use a high quality cleaner wax, such as mopar威 cleaner wax or equivalent to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. Caution! • do n...

  • Page 473

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider installing mud or stone shields behind each wheel. • use mopar威 touch-up paint or equivalent on scratches ...

  • Page 474

    Caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Glass surfaces all glass surfaces should be cleaned on a regular basis...

  • Page 475

    Replace the belts if they appear frayed or worn or if the buckles do not work properly. Appearance care for fabric top models caution! To maintain the appearance of your vehicle’s interior trim and top, follow these precautions: • avoid leaving your vehicle unattended with the top down, as exposure ...

  • Page 476

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • avoid high-pressure car washes, as they can dam- age the top material. Also, increased water pres- sure may force past the weather strips. • it is recommended that the top be free of wa...

  • Page 477

    Cleaner or equivalent will safely clean all plastic win- dows without scratching. It removes fine scratches to improve visibility and provides uv protection to help prevent yellowing. 2. When washing, never use hot water or anything stronger than a mild soap. Never use solvents such as alcohol or ha...

  • Page 478

    Fuses totally integrated power module the totally integrated power module (tipm) is located in the engine compartment near the battery. This center contains cartridge fuses, mini fuses and relays. A label that identifies each component is printed on the inside of the cover. Cavity cartridge fuse min...

  • Page 479

    Cavity cartridge fuse mini fuse description j9 40 amp green pzev sec motor feed/flex fuel j10 30 amp pink headlamp wash relay/manifold tun- ing valve j11 30 amp pink sway bar j13 60 amp yellow ignition off draw (iod) — main j14 40 amp green ebl (rear window defogger) j15 30 amp pink rear blower j17 ...

  • Page 480

    Cavity cartridge fuse mini fuse description m3 20 amp yellow frt/rear axle locker relay m4 — — m5 — — m6 20 amp yellow power outlet #1/rain sensor m7 20 amp yellow power outlet #2 (batt/acc select) m8 20 amp yellow front heated seat m9 20 amp yellow rear heated seat (if equipped) cavity cartridge fu...

  • Page 481

    Cavity cartridge fuse mini fuse description m12 30 amp green amplifier (amp) m13 20 amp yellow ignition off draw— cabin compartment node (iod-ccn), wireless control module (wcm), si- ren, multifunction control switch (mul- tifctn sw) m14 20 amp yellow trailer tow (export only) cavity cartridge fuse ...

  • Page 482

    Cavity cartridge fuse mini fuse description m16 10 amp red occupant restraint controller (orc) m17 15 amp blue left tail/license/ park lamp (lt-tail/ lic/prk lmp) m18 15 amp blue right tail/park/run lamp (rt-tail/ prk/run lmp) m19 25 amp natural auto shut down (asd #1 and #2) m20 15 amp blue cabin c...

  • Page 483

    Cavity cartridge fuse mini fuse description m30 15 amp blue wiper motor frt, j1962 diagnostic feed m31 20 amp yellow backup lamps (b/u lamps) m32 10 amp red occupant restraint controller (orc), tt europe m33 10 amp red next generation con- troller (ngc), global powertrain engine controller (gpec) ca...

  • Page 484

    Cavity cartridge fuse mini fuse description m38 25 amp natural lock/unlock motors (lock/unlock mtrs) caution! • when installing the integrated power module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrat...

  • Page 485

    • store the removed iod fuse in the power distribution center location #11 labeled “iod storage.” • or, disconnect the negative cable from the battery. • anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for abou...

  • Page 486

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamp 1. Open hood and support u...

  • Page 487

    Front park/turn signal 1. Remove the front grille. Turn the retainers along the top 1/4 turn counterclockwise and remove. 2. Pull the bottom of the grille away starting at one side and working toward the other. 3. Turn the socket assembly 1/4 turn counterclockwise and remove from housing. Pull the b...

  • Page 488

    Rear tail, stop, turn signal, and backup lamp 1. Remove the two inboard screws attaching the tail light housing to the body. Do not remove the outer screws at any time. 2. Separate the housing from the body by pushing the lamp inboard while pulling the lamp away from the body. 3. Rotate the appropri...

  • Page 489

    Fluid capacities u.S. Metric fuel (approximate) — two door models 18.5 gallons 70 liters fuel (approximate) — four door models 22.5 gallons 85 liters engine oil with filter 3.8 liter engine 6 quarts 5.7 liters cooling system * 3.8 liter engine (mopar 威 antifreeze/engine coolant 5 year/100,000 mile f...

  • Page 490

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) or equivalent. Engine oil use api certified sae 5w-20 engine oil, meeting the requirements of chrysl...

  • Page 491

    Chassis component fluid, lubricant, or genuine part automatic transmission mopar 威 atf+4 automatic transmission fluid or equivalent. Manual transmission mopar 威 manual transmission lubricant or equivalent (meeting the re- quirements of chrysler material standard ms-9224). Transfer case mopar 威 atf+4...

  • Page 493: Maintenance Schedules

    Maintenance schedules contents 䡵 emissions control system maintenance . . . . . . 494 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 494 ▫ required maintenance intervals . . . . . . . . . . 496 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 494

    Emissions control system maintenance the scheduled maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done t...

  • Page 495

    • change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, which- ever comes first. Your dealer will reset the oil change indicator message after completing ...

  • Page 496

    At each oil change • change the engine oil filter. • inspect the brake hoses and lines. • check the manual transmission fluid level. Caution! Failure to perform the required maintenance items may result in damage to the vehicle. Required maintenance intervals refer to the maintenance schedules on th...

  • Page 497

    6,000 miles (10,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 12,000 miles (20,000 km) or 12 months maintenance service schedule ❏ change the engine...

  • Page 498

    18,000 miles (30,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front & rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # dea...

  • Page 499

    30,000 miles (50,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the manual transmission fluid if using your veh...

  • Page 500

    36,000 miles (60,000 km) or 36 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings, ...

  • Page 501

    48,000 miles (80,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings, ...

  • Page 502

    60,000 miles (100,000 km) or 60 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect the brake linings, replace if necessary. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ ch...

  • Page 503

    66,000 miles (110,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 72,000 miles (120,000 km) or 72 months maintenance service schedule ❏ change the en...

  • Page 504

    78,000 miles (130,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 84,000 miles (140,000 km) or 84 months maintenance service schedule ❏ change the en...

  • Page 505

    90,000 miles (150,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ inspect and replace pcv valve if necessary.† ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change...

  • Page 506

    96,000 miles (160,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake linings,...

  • Page 507

    108,000 miles (180,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ if using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ inspect the brake lining...

  • Page 508

    120,000 miles (200,000 km) or 120 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ replace accessory drive belt(s). ❏ inspect the brake linings, replace if necessary. ❏ inspect exhaust system. ❏ inspect the ...

  • Page 509

    126,000 miles (210,000 km) or 126 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ inspect the front & rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. Odometer reading date repair order # ...

  • Page 510

    138,000 miles (230,000 km) or 138 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. Odometer reading date repair order # dealer code signature authorized chrysler dealer 144,000 miles (240,000 km) or 144 months maintenance service schedule ❏ change th...

  • Page 511

    150,000 miles (250,000 km) or 150 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate tires. ❏ replace the engine air cleaner filter. ❏ adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ change the manual transmission fluid if using your ...

  • Page 512

    † this maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about...

  • Page 513: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515 ▫ prepare for the appointment . . . . . . . . . . . 515 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 515 ▫ be reasonable with r...

  • Page 514

    䡵 publication order forms . . . . . . . . . . . . . . . . 520 䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 521 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 521 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 5...

  • Page 515

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 516

    Warranty service must be done by an authorized dealer. We strongly recommend that you take the vehicle to an authorized dealer. They know your vehicle the best, and are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealers have the facilities, factory-tra...

  • Page 517

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 518

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 519

    Mopar 姞 parts mopar 威 fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your ve...

  • Page 520

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 521

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 522

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 523: Index

    Index 10

  • Page 524

    Abs (anti-lock brake system) . . . . . . . . . . . . 249,362 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 air cleaner, engine (engine air cleaner filter) . . . 451 air conditioner maintenance . . . . . . . . . . . . . . . 452 air conditioning . . . . . . . . . . . . . . . . ...

  • Page 525

    Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451 emergency starting . . . . . . . . . . . . . . . . . . . . . 436 keyless transmitter replacement (rke) . . . . . . . 23 belts, seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38,74 body mechanism lubrication . . ....

  • Page 526

    Child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 climate control . . . . . . . . . . . . . . . . . . . . . . . . . 309 clock . . . . . . . . . . . . . . . . . . . . . . . . 267,281,284,293 compact disc (cd) maintenance . . . . . . . . . . . . . 308 compass . . . . . . . . . ...

  • Page 527

    Disposal engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 450 used coolant (antifreeze) . . . . . . . . . . . . . . . . 461 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 driver’s seat...

  • Page 528

    Fuel requirements . . . . . . . . . . . . . . . . . . 401,489 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . 436 oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448,489 oil disposal . . . . . . . . . . . . . . . . . . . . . . . . . . 450 oil filter . . . . . . . . . ...

  • Page 529

    Fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . 132,487 fold and tumble rear seat . . . . . . . . . . . . . . . . . 123 folding rear seat . . . . . . . . . . . . . . . . . . . . . . . . 126 folding windshield . . . . . . . . . . . . . . . . . . . . . . 231 four wheel drive . . . . . ....

  • Page 530

    Hard top, modular . . . . . . . . . . . . . . . . . . . . . . 153 hard top removal . . . . . . . . . . . . . . . . . . . . . . . 161 hazard warning flasher . . . . . . . . . . . . . . . . . . . 430 head restraints . . . . . . . . . . . . . . . . . . . . . . . . . 122 head rests . . . . . . . . . . ....

  • Page 531

    Jacking instructions . . . . . . . . . . . . . . . . . . . . . . 433 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . 436 key, programming . . . . . . . . . . . . . . . . . . . . . . . . 16 key, replacement . . . . . . . . . . . . . . . . . . . . . . . . 15 key, sentry (immobilizer)...

  • Page 532

    Engine temperature warning . . . . . . . . . . . . . . 250 exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132,487 hazard warning flasher . . . . . . . . . . . . . . . . . 430 headlight switch . . . . . . . . . . ....

  • Page 533

    Maintenance procedures . . . . . . . . . . . . . . . . . . . 447 maintenance schedule . . . . . . . . . . . . . . . . . . . . 494 malfunction indicator light (check engine) . . 256,445 manual, service . . . . . . . . . . . . . . . . . . . . . . . . . 520 manual transmission . . . . . . . . . . . . ....

  • Page 534

    Oil pressure light . . . . . . . . . . . . . . . . . . . . . . . 247 onboard diagnostic system . . . . . . . . . . . . . . 444,445 operator manual (owner’s manual) . . . . . . . . . . . . 6 outside rearview mirrors . . . . . . . . . . . . . . . . . . 83 overheating, engine . . . . . . . . . . . . . ...

  • Page 535

    Reformulated gasoline . . . . . . . . . . . . . . . . . . . . 401 refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453 release, hood . . . . . . . . . . . . . . . . . . . . . . . . . . 128 reminder, lights on . . . . . . . . . . . . . . . . . . . . . 132 reminder, seat belt . . . ...

  • Page 536

    Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 118 easy entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 fold and tumble rea...

  • Page 537

    Automatic transmission . . . . . . . . . . . . . . . . . 323 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . 324 engine block heater . . . . . . . . . . . . . . . . . . . . 327 engine fails to start . . . . . . . . . . . . . . . . . . . . 324 manual transmission . . . . . . . . . . . ...

  • Page 538

    Inflation pressures . . . . . . . . . . . . . . . . . . . . . 388 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 431,434 load capacity . . . . . . . . . . . . . . . . . . . . . 383,384 pressure monitor system (tpms) . . . . . . . . . . . 395 pressure warning light . . . . . . . . . . ...

  • Page 539

    Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 469 transmission automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 maintenance . . . . . . . . . . . . . . . . . . . . . . . 465,468 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 range indicator . ...

  • Page 540

    Window fogging . . . . . . . . . . . . . . . . . . . . . . . . 316 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 windshield defroster . . . . . . . . . . . . . . . . . . . . . . 75 windshield, folding . ....