1. DL manuals
  2. Jeep
  3. Automobile
  4. 2012 Wrangler
  5. Owner's Manual

Jeep 2012 Wrangler Owner's Manual

Manual is about: 2012

Summary of 2012 Wrangler

  • Page 1

    Wrangler includes wrangler unlimited chrysler group llc o w n e r ’ s m a n u a l 2 0 12 w ra n g le r 12jk72-126-aa first edition printed in u.S.A. 2 0 1 2 907711 wrangler om cover.Indd 1 3/28/11 1:48 pm.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 how to use this manual . . . . . . . . . . . . . . . . . . 6 䡵 warnings and cautions . . . . . . . . . . . . . . . . . . . 8 䡵 vehicle ide...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle. It can go places and perform tasks t...

  • Page 7

    Note: after reviewing the owner information, it should be stored in the vehicle for convenient referenc- ing and remain with the vehicle when sold. When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech- nicians and genuine mopar 威 parts, and...

  • Page 8

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. How to use this manual consult the table of contents to determine...

  • Page 9

    1 introduction 7.

  • Page 10

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 11

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 1 introduction 9.

  • Page 13: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . . . . . 14 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . 15 䡵 sentry key威 . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 14

    ▫ to turn off flash lights with lock . . . . . . . . 25 ▫ programming additional transmitters . . . . . . 25 ▫ general information . . . . . . . . . . . . . . . . . . . 26 ▫ transmitter battery replacement . . . . . . . . . . 26 䡵 remote starting system — if equipped . . . . . . . 27 ▫ how to use re...

  • Page 15

    ▫ seat belts in passenger seating positions . . . . . 55 ▫ automatic locking retractor mode (alr) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . 56 ▫ energy management feature . . . . . . . . . . . . . 57 ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . 58 ▫ enhanced seat...

  • Page 16

    A word about your keys the keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice. Igni...

  • Page 17

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children...

  • Page 18

    Sentry key 姞 the sentry key 威 immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded ...

  • Page 19

    All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement keys note: only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a sentry key 威 is programmed to a vehicle, it cannot be programmed to any...

  • Page 20

    3. Insert the second valid key into the ignition switch. Turn the ignition switch to the on/run position within 15 seconds. After 10 seconds, a chime will sound. In addition, the vehicle security light will begin to flash. Turn the ignition switch to the lock position and remove the second key. 4. I...

  • Page 21

    General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference...

  • Page 22

    Switch while the door is open. After all the doors are locked and closed, the vehicle security light (located on the instrument cluster) will flash rapidly for about 16 sec- onds to signal that the vehicle security alarm is arming. During this 16-second arming period, opening any door or the swing g...

  • Page 23

    Illuminated entry — if equipped the courtesy lights will turn on when you use the remote keyless entry (rke) transmitter to unlock the doors or open any door. This feature also turns on the approach lighting in the outside mirrors (if equipped). Refer to “mirrors” in “understanding the features of y...

  • Page 24

    Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors, swing gate, and activate the panic alarm from a maxi- mum distance of 66 ft (20 m) using a remote keyless entry (rke) transmitter. The rke transmitter does not need to be pointed at the vehicle to activate t...

  • Page 25

    • for vehicles not equipped with the evic, the remote unlock feature can be enabled or disabled by perform- ing the following steps: 1. Press and hold the lock button on a programmed rke transmitter. 2. Continue to hold the rke transmitter lock button for at least four seconds, but not longer than 1...

  • Page 26

    Sound horn on lock this feature will cause the horn to chirp when the doors are locked with the rke transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to “elec- tronic vehicle information center (e...

  • Page 27

    To turn off flash lights with lock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles equipped with the evic, refer to...

  • Page 28

    General information this device complies with part 15 of fcc rules and with rs-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may...

  • Page 29

    2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the rke transmitter case, snap the two halves together. Remote starting system — if equipped this sy...

  • Page 30

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switch • battery at an acceptable cha...

  • Page 31

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 32

    Remote start will also cancel if any of the following occur: • the engine stalls or rpm exceeds 2500 • any engine warning lamps come on • the hood is opened • the hazard switch is pressed • the transmission is moved out of park • the brake pedal is pressed to exit remote start mode without driving t...

  • Page 33

    Doors caution! Careless handling and storage of the removable door panels may damage the seals, causing water to leak into the vehicle’s interior. Upper half door window removal — if equipped grasp the half door window and pull upward. Upper half door window 2 things to know before starting your veh...

  • Page 34

    Upper half door window installation — if equipped 1. Grasp the half door window and line up the pins with the pockets in the lower door. 2. Push down to ensure the half door window is fully seated. Front door removal warning! Do not drive your vehicle on public roads with the doors removed as you wi...

  • Page 35

    Note: if the red latch on the connector is locked, push the red latch down until you can only see the latch on one end (top) of the connector. This will unlock the connector tab, allowing the tab to be pressed down and enabling the harness to be disconnected. 4. Unhook the door strap from the body h...

  • Page 36

    5. With the door open, lift the door to clear the hinge pins from their hinges and remove the door. Note: doors are heavy; use caution when removing them. To reinstall the door(s), perform the previous steps in the opposite order. Rear door removal (four-door models) warning! Do not drive your vehic...

  • Page 37

    5. Unplug the wiring harness connector. Note: if the red latch on the connector is locked, push the red latch to the right until you can only see the latch on one end (right) of the connector. This will unlock the connector tab, allowing the tab to be pressed down and enabling the harness to be disc...

  • Page 38

    To reinstall the door(s), perform the previous steps in the opposite order. Door locks manual door locks all doors are equipped with an interior rocker-type door lock lever. To lock a door when leaving your vehicle, press the rocker lever forward to the lock position and close the door. To unlock th...

  • Page 39

    Note: the ignition key that is used to start the vehicle is used to lock or unlock the doors, swing gate, glove compartment, and console storage. Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle....

  • Page 40

    Power door locks — if equipped the power door lock switch is located on each front door panel. Press the switch forward to lock the doors, and rearward to unlock the doors. Warning! • for personal security reasons and safety in an accident, lock the vehicle doors when you drive, as well as when you ...

  • Page 41

    Automatic door locks — if equipped when enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer per written request of the customer. Please see your authorized dealer for servic...

  • Page 42

    Child-protection door lock system — rear doors to provide a safer environment for small children riding in the rear seats, the rear doors are equipped with child-protection door lock system. To engage or disengage the child-protection door lock system 1. Open the rear door. 2. Insert the tip of the ...

  • Page 43

    Note: for emergency exit with the system engaged, move the rocker lever rearward (unlocked position), roll down the window and open the door with the outside door handle. Windows power windows — if equipped the power window switches are located on the instru- ment panel below the radio. Press the sw...

  • Page 44

    Four-door models the lower left switch controls the left rear passenger window, and the lower right switch controls the right rear passenger window. Auto-down both the driver and front passenger window switches have an “auto-down” feature. Press the window switch past the first detent, release, and ...

  • Page 45

    Rear power windows — four-door models the rear passenger window switches are located on the back of the center floor console. Press the switch down- ward to open the window and upward to close the window. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a h...

  • Page 46

    Rear swing gate the rear swing gate can be unlocked by using the key, remote keyless entry (rke) transmitter, or by activating the power door lock switches located on the front doors. To open the swing gate, press the button on the gate handle. Note: close the rear flip-up window before attempting t...

  • Page 47

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for the driver and all passengers • advanced front air bags for driver and front passen- ger • supplemental seat-mounted side air bags (sab) — if equipped • ...

  • Page 48

    Note: the advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on the severity and type of collision. Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. Children 12 years old and u...

  • Page 49

    4. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between you and the door. 5. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer...

  • Page 50

    Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of in...

  • Page 51

    Warning! (continued) • be sure everyone in your vehicle is in a seat and using a seat belt properly. • wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision th...

  • Page 52

    2. The seat belt latch plate is above the back of the front seat and next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the la...

  • Page 53

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is loose will not protect you properly. In a sudden stop you...

  • Page 54

    Note: the seat belt reminder light will remain on until the driver and front passenger (if equipped with front passenger beltalert 威) seat belt is buckled. For further information, refer to “enhanced seat belt use reminder system (beltalert 威)”. Warning! • a lap belt worn too high can increase the r...

  • Page 55

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protecti...

  • Page 56

    Warning! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the rear seatback is in the fully upright and locked position when occupied. If the rear seatback is not fully upright and locked and the rear center lap/shoulder belt can be pulled out of the retractor, th...

  • Page 57

    Warning! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. As a guide, if you are shorter than average, you ...

  • Page 58

    Additional information, refer to “installing child re- straints using the vehicle seat belt” under the “child restraints” section. The chart below defines the type of feature for each seating position. Driver center passenger first row n/a n/a alr second row alr alr alr • n/a — not applicable • alr ...

  • Page 59

    How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in t...

  • Page 60

    Warning! • the belt and retractor assembly must be replaced if the seat belt assembly automatic locking re- tractor (alr) feature or any other seat belt func- tion is not working properly when checked ac- cording to the procedures in the service manual. • failure to replace the belt and retractor as...

  • Page 61

    The beltalert 威 warning sequence begins after the vehicle speed is over 5 mph (8 km/h), by blinking the seat belt reminder light and sounding an intermittent chime. Once the sequence starts, it will continue for the entire duration or until the respective seatbelts are fastened. After the sequence c...

  • Page 62

    Seat belt extender if a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long...

  • Page 63

    Note: these air bags are certified to the new federal regulations for advanced air bags. The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation that are based on the severity and type of collision. This vehicle may be equipped with...

  • Page 64

    Air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolster • driver advanced front air bag • passenger advanced front air bag •...

  • Page 65

    Warning! • no objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • do not put anything on or around the air bag covers or attempt to open them manually. Y...

  • Page 66

    Warning! (continued) • do not mount any accessories to the knee bolster such as alarm lights, stereos, citizen band radios, etc. Supplemental seat-mounted side air bags (sab) — if equipped supplemental seat-mounted side air bags (sab) may provide enhanced protection to help protect an occupant durin...

  • Page 67

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the sab during deployment could cause you to be severely injured or killed. Knee impact bolsters the knee impact bolsters help protect the knees of the driver and the fr...

  • Page 68

    The advanced front air bags will not deploy in all frontal collisions, including some that may produce sub- stantial vehicle damage — for example, some pole colli- sions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, advanced front ai...

  • Page 69

    It also includes diagnostics that will illuminate the instru- ment cluster air bag warning light if a malfunction is noted that could affect the air bag system. The diagnos- tics also record the nature of the malfunction. Warning! Ignoring the air bag warning light in your instru- ment panel could m...

  • Page 70

    Supplemental seat-mounted side air bags (sab) inflator units — if equipped the supplemental seat-mounted side air bags inflator units (if equipped) are designed to activate only in certain side collisions. The orc determines if a side collision requires the side air bags to inflate, based on the sev...

  • Page 71

    • flash hazard lights as long as the battery has power or until the ignition key is turned off. • turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • unlock the doors automatically. If a deployment occurs the advanced front air bags a...

  • Page 72

    • do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! • deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioner, and s...

  • Page 73

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 74

    • the air bag warning light remains on after the four to eight-second interval. • the air bag warning light comes on intermittently or remains on while driving. Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be dis...

  • Page 75

    The edr under normal driving conditions and no per- sonal data (e.G., name, gender, age, and crash location) are recorded. However, other parties, such as law en- forcement, could combine the edr data with the type of personally identifying data routinely acquired during a crash investigation. To re...

  • Page 76

    Warning! In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any ...

  • Page 77

    Warning! • rearward-facing child seats must never be used in the front seat of a vehicle with the front passenger air bag unless the air bag is turned off. An air bag deployment could cause severe injury or death to infants in this position. • improper installation can lead to failure of an infant o...

  • Page 78

    Retractor and then allow the belt to retract into the retractor. For additional information on alr, refer to “automatic locking mode”. • in the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path open...

  • Page 79

    In the vehicle by the lap/shoulder belt or the latch child restraint anchorage system. Refer to “lower an- chors and tether for children (latch)”. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s s...

  • Page 80

    Separate straps on each side, with each having a hook or connector for attachment to the lower anchorage, and a means for adjusting the tension of the strap. Forward- facing toddler restraints and some rearward-facing infant restraints will also be equipped with a tether strap having a hook for atta...

  • Page 81

    And are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces. Regardless of the specific type of lower attachment, never install latch-compatible child seats suc...

  • Page 82

    Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave an unattended child in the vehicle. All three rear seating positions of the four-door model have lower anchorages that are capable of accommodat- ing latch-compatible child seats having...

  • Page 83

    Restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces. Latch anchorages (two-door models) latch anchorages (four-door models) 2 things to know before starting your vehicle 81.

  • Page 84

    In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means for adjust...

  • Page 85

    A hook for attachment to the tether strap anchorage, and a means for adjusting the tension of the strap. You will first loosen the child seat adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next, attach the l...

  • Page 86

    Description under “seat belts in passenger seating posi- tions” section. The chart below defines the seating posi- tions with an automatic locking retractor (alr) or a cinching latch plate. Driver center passenger crs lock crs lock crs lock first row n/a n/a alr second row alr alr alr • n/a — not ap...

  • Page 87

    To attach a child restraint tether strap: route the tether strap over the seatback and attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether under the head restraint, and attach the hook to the tether anchor located on the back of ...

  • Page 88

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Vehicles with rear web buckles that may need to be twisted • in the rear seat...

  • Page 89

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 500 miles (800 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 90

    Warning! (continued) • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and se...

  • Page 91

    Warning! (continued) • if it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained ...

  • Page 92

    Authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an autho- rized dealer. Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. Se...

  • Page 93

    Warning! (continued) • check mounting of mats on a regular basis. Al- ways properly reinstall and secure floor mats that have been removed for cleaning. • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake peda...

  • Page 94

    Fluid leaks check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately. 92 things to know before...

  • Page 95: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 ▫ inside day/night mirror . . . . . . . . . . . . . . . . 98 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . 98 ▫ power mirrors — if equipped . . . . . . . . . ....

  • Page 96

    䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 ▫ front seat adjustment . . . . . . . . . . . . . . . . . 138 ▫ manual seat height adjustment — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 139 ▫ front seatback recline . . . . . . . . . . . . . . . . . 140 ▫...

  • Page 97

    ▫ front fog lights . . . . . . . . . . . . . . . . . . . . . 156 ▫ instrument panel dimmer . . . . . . . . . . . . . . 156 ▫ daytime running lights — if equipped . . . . 157 ▫ interior lights . . . . . . . . . . . . . . . . . . . . . . 157 䡵 windshield wipers and washers . . . . . . . . . . 159 ▫ wi...

  • Page 98

    䡵 dual top — if equipped . . . . . . . . . . . . . . . . 174 ▫ removing the soft top . . . . . . . . . . . . . . . . 174 ▫ installing the soft top . . . . . . . . . . . . . . . . 177 䡵 freedom top™ three-piece modular hard top — if equipped . . . . . . . . . . . . . . . . . . . . . . . . 179 ▫ front...

  • Page 99

    䡵 sunrider威 (two-door models) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 251 ▫ opening the sunrider威 . . . . . . . . . . . . . . . . 252 ▫ closing the sunrider威 . . . . . . . . . . . . . . . . 254 䡵 sunrider威 (four-door models) — if equipped . . . . . . . . . . . . . . . . . ....

  • Page 100

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward...

  • Page 101

    Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distan...

  • Page 102

    Power mirrors — if equipped the power mirror switch is located on the center of the instrument panel, below the climate controls. A rotary knob selects the left mirror, right mirror or off position. After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the ce...

  • Page 103

    Uconnect™ phone — if equipped uconnect™ phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ phone al- lows you to dial a phone number with your mobile phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s a...

  • Page 104

    Uconnect™ phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The uconnect™ phone is driven through your bluetooth 威 “hands-free profile” mobile phone. Uconnect™ featur...

  • Page 105

    Voice command button actual button location may vary with the ra- dio. The individual buttons are described in the “operation” section. The uconnect™ phone can be used with any hands-free profile certified bluetooth 威 mobile phone. See the uconnect™ website for supported phones. Refer to your mobile...

  • Page 106

    Example, you can use the compound form voice command “phonebook new entry”, or you can break the compound form command into two voice com- mands: “phonebook” and “new entry”. Please re- member, the uconnect™ phone works best when you talk in a normal conversational tone, as if speaking to someone si...

  • Page 107

    • when prompted, after the beep, say “pair a phone” and follow the audible prompts. • you will be asked to say a four-digit personal identi- fication number (pin), which you will later need to enter into your mobile phone. You can enter any four-digit pin. You will not need to remember this pin afte...

  • Page 108

    • the uconnect™ phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by saying a name • press the button to begin. • after the “ready” prompt and the following beep, say “call”. • the system will prompt you to say the name of the person you...

  • Page 109

    • when prompted, enter the number designation (e.G., “home”, “work”, “mobile”, or “other”). This will allow you to store multiple numbers for each phone- book entry, if desired. • when prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an ent...

  • Page 110

    • depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previous downloaded phonebook is available for use. • only the phonebook of the currently connected mobile phone is accessible. • only...

  • Page 111

    First disconnect or drop the bluetooth 威 connection to the uconnect™ phone, and then send the address book entry via bluetooth 威. Please see your phone owner’s manual for specific instructions on how to drop the bluetooth 威 connection. • if the phonebook entry is longer than 24 characters, it will o...

  • Page 112

    Delete uconnect™ phonebook entry note: editing phonebook entries is recommended when the vehicle is not in motion. • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook delete”. • after you enter the phonebook delete menu, you will then be asked for the name ...

  • Page 113

    • note that only the phonebook in the current language is deleted. • automatic downloaded phonebook entries cannot be deleted or edited. List all names in the uconnect™ phonebook • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook list names”. • the uconnec...

  • Page 114

    Call, press and hold the button until you hear a single beep, indicating that the incoming call was rejected. Answer or reject an incoming call - call currently in progress if a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting th...

  • Page 115

    Conference call when two calls are in progress (one active and one on hold), press and hold the button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-way calling to initiate three-way calling, press the button while a call is in progress, ...

  • Page 116

    Call continuation call continuation is the progression of a phone call on the uconnect™ phone after the vehicle ignition key has been switched to off. Call continuation functionality avail- able on the vehicle can be any one of three types: • after the ignition key is switched to off, a call can con...

  • Page 117

    Emergency assistance if you are in an emergency and the mobile phone is reachable: • pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the uconnect™ phone is operational, you may reach the emergency number as follows: • press the button to begi...

  • Page 118

    Towing assistance if you need towing assistance: • press the button to begin. • after the “ready” prompt and the following beep, say “towing assistance”. Note: • the towing assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the u.S., 1-877-213-4525 f...

  • Page 119

    When calling a number with your uconnect™ phone that normally requires you to enter in a touch-tone sequence on your mobile phone keypad, you can press the button and say the sequence you wish to enter, followed by the word “send”. For example, if required to enter your pin followed with a pound, (3...

  • Page 120

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G., the uconnect™ phone will not repeat a phone number before you dial it). • press the button to begin. • after the “ready” prompt and the following beep, say: − “setup confirma...

  • Page 121

    Mute/un-mute (mute off) when you mute the uconnect™ phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect™ phone: • press the button. • following the beep, say “mute”. In order to un-mute th...

  • Page 122

    • when prompted, say “list phones”. • the uconnect™ phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “select” or “delete”. Also, see the next two sec- tions f...

  • Page 123

    Things you should know about your uconnect™ phone uconnect™ phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect™ tutorial”. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect™ pho...

  • Page 124

    Voice command • for best performance, adjust the rearview mirror to provide at least 1 ⁄ 2 in (1 cm) gap between the overhead console (if equipped) and the mirror. • always wait for the beep before speaking. • speak normally, without pausing, just as you would speak to a person sitting a few feet/me...

  • Page 125

    • numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • you can say “o” (letter “o”) for “0” (zero). • even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • in a ...

  • Page 126

    Sms uconnect™ phone can read or send new messages on your phone. Read messages: if you receive a new text message while your phone is connected to uconnect™ phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • press the button. • ...

  • Page 127

    List of preset messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L o l 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See you in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18....

  • Page 128

    Turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and the following beep, say “setup, incoming message announcement,” you will then be given a choice to chan...

  • Page 129

    3 understanding the features of your vehicle 127.

  • Page 130

    128 understanding the features of your vehicle.

  • Page 131

    3 understanding the features of your vehicle 129.

  • Page 132

    Voice commands primary alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all voice commands primary alternate(s) call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home 130 unders...

  • Page 133

    Voice commands primary alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate(s) return to main menu return or main menu select phone select send set up...

  • Page 134

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 135

    Note: if you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the voice command button, listen for the beep, and say your command. Pressing the voice command button while the system i...

  • Page 136

    Changing the volume 1. Start a dialogue by pressing the voice command button. 2. Say a command (e.G., “help”). 3. Use the on/off volume rotary knob to adjust the volume to a comfortable level while the voice command system is speaking. Please note the volume setting for voice command is different th...

  • Page 137

    Radio fm to switch to the fm band, say “fm” or “radio fm”. In this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “menu radio” (to switch to the radio menu) • “m...

  • Page 138

    Memo to switch to the voice recorder mode, say “memo”. In this mode, you may say the following commands: • “new memo” (to record a new memo) — during the recording, you may press the voice command button to stop recording. You proceed by saying one of the following commands: − “save” (to save the me...

  • Page 139

    • “language spanish” • “tutorial” • “voice training” note: keep in mind that you have to press the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers ...

  • Page 140

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • be sure everyone in your vehicle is in a seat and using a seat belt properl...

  • Page 141

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 142

    Front seatback recline lean forward before lifting the handle, then lean back to the desired position and release the handle. Lift the handle to return the seatback to an upright position. Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your che...

  • Page 143

    Front passenger easy entry seat — two-door models pull upward on the recline lever (toward the rear of the vehicle) and slide the entire seat forward. To return the seat to a sitting position, rotate the seatback upright until it locks and push the seat rearward until the track locks. Easy entry lev...

  • Page 144

    Note: • the front passenger seats have a track memory, which returns the seat to just past the halfway point of the track regardless of its original position. • the recliner and easy entry levers should not be used during the automatic returning of the seat to its sitting position. Tip n’ slide seat...

  • Page 145

    Passenger seat in addition to easy entry, the front passenger seat is also equipped with tip n’ slide. This feature allows for easier entry for rear passengers. Pull upward on the recline lever and slide the entire seat forward (easy entry). Tip n’ slide easy entry lever 3 understanding the features...

  • Page 146

    With the seat forward, pull the entire seat assembly toward the instrument panel. Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. There are two heated seat switches that allow the driver and passeng...

  • Page 147

    That time, the number of illuminated leds changes from two to one, indicating the change. The low-level setting will turn off automatically after approximately 30 min- utes. Note: when a heat setting is selected, heat will be felt within two to five minutes. Warning! • persons who are unable to feel...

  • Page 148

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 149

    Fold and tumble rear seat — two-door models note: • prior to folding the rear seat, it may be necessary to reposition the front seats. • be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. 1. Lift the seatback release lever and fo...

  • Page 150

    2. Slowly flip the entire seat forward. 3. Return the seat to the normal position. 4. Raise the rear seatback using the assist strap and firmly lock the seat into position. Removing the rear seat — two-door models warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 151

    2. Press down on the release bar on each side, and pull the seat out and away from the lower bracket. 3. Remove the seat from the vehicle. Replacing the rear seat — two-door models reverse the steps for removing the seat. Warning! • to help protect against personal injury, passengers should not be s...

  • Page 152

    Note: • prior to folding the rear seat, it may be necessary to reposition the front seat to its mid-track position. • be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. Warning! • it is extremely dangerous to ride in a cargo area...

  • Page 153

    To raise the rear seat raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Note: if the rear seatback is not fully latched, the center shoulder belt will not be ab...

  • Page 154

    Down slightly on the hood before pushing the safety latch. Insert the support rod into the slot on the hood. To close the hood, remove the support rod from the hood panel and place it in the retaining clip. Lower the hood slowly. Secure both of the hood latches. Warning! Be sure the hood is fully la...

  • Page 155

    Headlights and parking lights turn the end of the multifunction lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. Note: lens fogging can occur under certain weather conditions. Turning the headlights on will usually accel- er...

  • Page 156

    Automatic headlights — if equipped this system automatically turns the headlights on or off according to the ambient light levels. To turn the system on, turn the end of the multifunction lever to the auto position (third detent). When the system is on, the headlight time delay feature is also on. T...

  • Page 157

    Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. • a tone will chime if the turn signals are left on for ...

  • Page 158

    Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer- ing wheel. This will turn on the high beam headlights until the lever is released. Front fog lights the front fog light switch is located on the multi- function lever. To ac...

  • Page 159

    Daytime running lights — if equipped the headlights come on at a low intensity level when shifted into any position other than park (auto trans- mission) or when the vehicle begins to move (manual transmission). Note: the daytime running light on the same side of the vehicle as the active turn signa...

  • Page 160

    The sports bar reading lights (available on four-door models) can be turned on by pressing the switches, located on either side of the lens. Press a switch a second time to turn the light off. The rear cargo light may be turned on by pressing the lens. Press the lens a second time to turn the light ...

  • Page 161

    Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located at the end of the lever. For information on using the rear window wiper/ washer, refer to “rear window features” in...

  • Page 162

    Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper opera- tion. Caution! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the...

  • Page 163

    Note: the wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield washers to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will star...

  • Page 164

    Mist feature push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on ...

  • Page 165

    Steering column up or down, as desired. Pull upwards on the lever to lock the column firmly in place. Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the ve...

  • Page 166

    The electronic speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic ...

  • Page 167

    To set a desired speed turn the electronic speed control on. When the vehicle has reached the desired speed, press the set (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. Note: the vehicle should be traveling at a steady speed and on level ground b...

  • Page 168

    Decrease until the button is released. Release the button when the desired speed is reached, and the new set speed will be established. Pressing the set (-) button once will result in a 1 mph (2 km/h) decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph (2 km/h). T...

  • Page 169

    The front power outlet is powered from the ignition switch. Power is available when the ignition switch is in the on or acc position. When the optional cigar lighter heating element is used in the power outlet, it heats when pushed in and pops out automatically when ready for use. To preserve the he...

  • Page 170

    On vehicles equipped with a rear subwoofer, there is a third power outlet located in the right rear cargo area. Rear power outlet — if equipped power outlet fuse locations 1 — m7 fuse 20 a yellow power outlet rear with sub woofer (opt.) 2 — m6 fuse 20 a yellow cigar lighter instrument panel 3 — m36 ...

  • Page 171

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 172

    Caution! (continued) • power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Power inverter — if equipped there is a 115 volt, 150 watt inverter outlet located on the front of the center console to convert dc current to ac curren...

  • Page 173

    May have to be reset manually. To reset the inverter manually press the power inverter button off and on. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. The power inverter switch is located on the instrument panel below the climate contro...

  • Page 174

    Cupholders front cupholders the front cupholders are located in the center console. Rear cupholders the rear cupholders are located on the back of the center console. Storage glovebox storage the lockable glovebox storage compartment is located on the passenger side of the lower instrument panel. Pu...

  • Page 175

    Console storage compartment to lock or unlock the storage compartment, insert the ignition key and turn. To open the storage compartment, press the latch and lift the cover. Rear storage compartment the rear cargo area storage compartment cover is held by a spring-loaded latch. In order to remove th...

  • Page 176

    3. Open the rear compartment cover. Dual top — if equipped if your vehicle is equipped with a dual top, you must remove one of the tops from the vehicle. If the soft top is removed, the pivot brackets must also be removed from the sport bar. The soft top was installed at the factory for shipping pur...

  • Page 177

    • two sunrider威 secure straps (if equipped) • two rear swing gate brackets 2. Remove the hard top. Refer to “freedom top three- piece modular hard top — front/rear panel removal” in this section. 3. Remove the soft top bow assembly pivot bracket screws (two per side) using a #t30 torx 威 head driver....

  • Page 178

    Note: to aid in disconnecting the knuckles, you may carefully tap on the knuckles using a rubber mallet. 5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx 威 head driver. Recover and re-zip the sports bar cover. Store the pivot brackets and...

  • Page 179

    Installing the soft top note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this section. 1. Locate and remove the following items prior to hard top removal: • right and left door frames • door frame attachment knobs (four for two-doo...

  • Page 180

    B. Lay the soft top into the rear of the vehicle with the bows pointing forward and the curved portion of the bows facing upward. C. Reattach the knuckles onto the metal pivot brackets. Note: to aid in reattaching the knuckles, you may carefully tap on the knuckles using a rubber mallet. D. Screw th...

  • Page 181

    Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 5. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside. Note: be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top. 6. U...

  • Page 182

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew: • it is recommended that the top be free of water prior to panel removal. Removing the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicles interior. • the ...

  • Page 183

    3. Turn the center l-shaped locks (two) from the center of the roof panel. 4. Turn the rear l-shaped lock (located above the shoul- der belt anchorage). 3 understanding the features of your vehicle 181.

  • Page 184

    5. Unlatch the header panel latch located at the top of the windshield. 6. Remove the left-hand panel. To remove the right panel, follow the steps above except for step 3. Freedom top™ storage bag vehicles equipped with a freedom top™ modular hard top, come with a freedom top™ storage bag that allow...

  • Page 185

    Unfold the black panel divider (ensure the divider is laying flat). Secure the velcro, located at the center of the divider. Insert the left-side freedom panel into the bag with the latches facing upward. 3 understanding the features of your vehicle 183.

  • Page 186

    Note: ensure the front freedom panel latch is closed prior to inserting the panel into the bag. Unfold the outer flap and zip the freedom bag closed. 184 understanding the features of your vehicle.

  • Page 187

    Install the seat attachment strap (at the top of the bag) through the loops. Lift the freedom bag into the vehicle with the hooks and straps facing the back of the rear seat. Attach the clips at the bottom of the bag to the child restraint anchorages, located at the base of the rear seat. 3 understa...

  • Page 188

    Wrap the upper strap around the rear head restraints and loop the strap through the buckle. Pull on the strap to tighten the freedom bag securely against the rear seat. Front panel(s) installation note: set the panels on the windshield frame so that there is no overhang. Also, make sure that the pan...

  • Page 189

    Front panel(s) installation with rear hard top removed 1. Turn the left and right panels over and move the spacer block (located on the rear of the panel) upward 90 degrees. Note: the front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there i...

  • Page 190

    4. Remove the six torx 威 head screws that secure the hard top to the vehicle (along the interior bodyside) using a #40 torx 威 head driver. 5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass. 6. Locate the wire harness on the left rear inside c...

  • Page 191

    7. Release the red locking tab by pulling outward. 8. To remove the wiring harness press the tab and pull downward to disconnect. Red locking tab press tab to disconnect 3 understanding the features of your vehicle 189.

  • Page 192

    9. To remove the washer hose, pinch the grips on hose connector and pull downward. 10. Close the swing gate. 11. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage. Caution! The removal of the freedom top requires four adults located on each corner. Failure ...

  • Page 193

    Note: • the torx fasteners that attach the hard top to the body should be torqued to 66 in lb +/- 22 in lb (7.5 n·m +/- 2.5 n·m) • it is not necessary to pinch connection when reinstall- ing washer hose. Push on until click is heard. Door frame warning! Do not drive your vehicle on pavement with the...

  • Page 194

    Door frame removal 1. Unscrew and remove the door frame attachment knobs (two per door). Warning! Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used. 2. Place one hand on the upper rear and one hand on the front of the door frame. 3....

  • Page 195

    4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Warning! Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle. 3 understand...

  • Page 196

    Door frame installation — two-door models 1. Unfold door frame and unscrew thumbscrews. 2. Set the door frame pin into the hole on top of the body side, behind the door opening. 3. After the door frame pin has been set into the body side hole, carefully set the front of the door frame into the rubbe...

  • Page 197

    5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. Door frame installation — four-door models 1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening. 3 understanding the feature...

  • Page 198

    3. Position the top of the door frame against the metal sport bar and press onto the side bar making sure not to pinch the material of the sports bar covers and to ensure it is properly positioned on the seal above the front of the rear door. 4. Loosely install the rear knob (long knob) to hold the ...

  • Page 199

    7. Position the rear of the front door frame to lay on top of the front of the rear door frame. Ensure the seals are installed correctly to avoid water leaks. 8. Loosely install both knobs beginning with the front knob (long knob). Then, install the middle knob (short knob) through the front and rea...

  • Page 200

    Soft top — two-door models please visit the owners section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a struct...

  • Page 201

    Caution! (continued) • refer to “appearance care for fabric top models” in “maintaining your vehicle” for further infor- mation. It contains important information on cleaning and caring for your vehicle’s fabric top. • do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clip...

  • Page 202

    Caution! (continued) • careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle’s interior. • the soft top must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior. Quick steps to loweri...

  • Page 203

    2. Release header latches from the windshield frame. 3. Release the sunrider 威 latch (both sides). 3 understanding the features of your vehicle 201.

  • Page 204

    4. Open the swing gate and lower the top. Note: ensure fabric does not overhang the sides of the vehicle. Quick steps to raising the soft top refer to “raising the soft top” in this section for further information. 1. Open the swing gate and raise the top, engaging the sunrider 威 latches (another pe...

  • Page 205

    2. Engage header latches. 3 understanding the features of your vehicle 203.

  • Page 206

    3. Install rear corner panels. 4. Install side and back windows. 204 understanding the features of your vehicle.

  • Page 207

    Lowering the soft top 1 — header bow 6 — quarter window 2 — 2–bow 7 — check strap 3 — 3–bow 8 — front retainer — quarter window 4 — sail panel 9 — bottom retainer — quarter window 5 — body side retainer 3 understanding the features of your vehicle 205.

  • Page 208

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 206 understanding the features of your vehicle.

  • Page 209

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 210

    5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across th...

  • Page 211

    6. Remove the rear window retainer from the swing gate bracket on both the left and right sides. 7. Stow the windows carefully to avoid scratching. 8. Undo the velcro 威 that runs along the top and rear edge of the side window. 9. Beginning from the rear lower corner, completely unzip the window. 10....

  • Page 212

    11. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 12. As you begin to lower the top, fold the sail panels so that they rest on top of the soft to...

  • Page 213

    13. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 14. Completely release the latches from the loops on the wi...

  • Page 214

    15. Make sure the plastic sleeves are slid rearward over the sunrider 威 link (sunrider威 models only). 16. Unlatch the side bows from both door rails (sun- rider 威 models only). 17. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Mo...

  • Page 215

    Note: help from another person will ease this opera- tion. 18. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle. 19. Close the front header latches. 20. Remove the door frames, if desired. ...

  • Page 216

    Raising the soft top 1. Unclip and move the sun visors to the side. 2. Install door frames, if removed. Refer to “door frame” in this section for further information. 3. Make sure the plastic sleeve is slid over sunrider 威 link (sunrider 威 models only). 4. Standing on the side of the vehicle, lift t...

  • Page 217

    5. Make sure the sunrider 威 bracket on the side bows latches to the door rails (sunrider 威 models only). 6. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 7. If the swing gate brackets were removed, install them by hooking the rear edge...

  • Page 218

    Over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the shortened rail edge. 8. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow. 216 understanding the features of your vehicle.

  • Page 219

    9. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to reach the channel with the retainers. 10. To install the side windows, affix the window tem- po...

  • Page 220

    11. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 1 — incorrect insertion 2 — correct insertion 218 understanding the feat...

  • Page 221

    12. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro 威 along the top and rear of the window. Repeat this step for the opposite side. 3 ...

  • Page 222

    13. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 14. Install the rear window by starting both zipper ends at the lower left ...

  • Page 223

    15. Run the zipper fully around to the right side of the window. 16. Grasp the swing gate bar and position it into the swing gate brackets. 3 understanding the features of your vehicle 221.

  • Page 224

    17. Insert the rear window retainer into the swing gate bracket on both the left and right sides. 18. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel. 19. Close the header latches and return the s...

  • Page 225

    Soft top — four-door models please visit the owner’s section of jeep.Com for instruc- tional videos. Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a stru...

  • Page 226

    Caution! (continued) • do not lower the top with the windows installed. Window and top damage may occur. • refer to “appearance care for fabric top models” in “maintaining your vehicle” for further infor- mation. It contains important information on cleaning and caring for your vehicle’s fabric top....

  • Page 227

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • it is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle...

  • Page 228

    Quick steps for lowering the soft top 1. Remove the side and back windows. 2. Release header latches from the windshield frame. 226 understanding the features of your vehicle.

  • Page 229

    3. Fold header rearward, pulling the fabric to the rear. 3 understanding the features of your vehicle 227.

  • Page 230

    4. Release sunrider 威 latch (both sides). 5. Open the swing gate and lower the top. Note: ensure the fabric does not overhang the sides of the vehicle. 228 understanding the features of your vehicle.

  • Page 231

    Quick steps for raising the soft top 1. Open the swing gate and raise the top, engaging the sunrider 威 latches (another person may be needed to help with this operation). 3 understanding the features of your vehicle 229.

  • Page 232

    2. Install rear corner panels. 3. Rotate the header forward. 230 understanding the features of your vehicle.

  • Page 233

    4. Engage the header latches. 5. Install the side and back windows. 3 understanding the features of your vehicle 231.

  • Page 234

    Folding down the soft top 1 — header bow 6 — body side retainer 2 — 2–bow 7 — quarter window 3 — 3–bow 8 — check strap 4 — 4–bow 9 — front retainer — quarter window 5 — sail panel 10 — bottom retainer — quarter window 232 understanding the features of your vehicle.

  • Page 235

    1 — zipper start 2 — zipper finish 3 — swing gate bar 4 — swing gate brackets 5 — sail panels 3 understanding the features of your vehicle 233.

  • Page 236

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 237

    5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets. • unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across th...

  • Page 238

    6. Remove the rear window retainer from the swing gate bracket on both the left and right sides. 7. Stow the windows carefully to avoid scratching. 8. Undo the velcro 威 that runs along the top and rear edge of the side window. 9. Beginning from the rear lower corner, completely unzip the window. 10....

  • Page 239

    11. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 12. Fold the sail panels so that they rest on top of the soft top. 3 understanding the features...

  • Page 240

    13. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 14. Grasp the front side bow behind the header, and lift th...

  • Page 241

    15. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck. 16. Fold the top so that the material forms a ⬙w⬙ as shown. Enter the vehicle and move the material into two folds. 3 understanding the features of your vehicle 239.

  • Page 242

    17. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 18. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Grasp the folded ...

  • Page 243

    19. Gently slide the side bows off the door frame track and lower the top down into the vehicle. Note: help from another person will ease this opera- tion. 20. Tuck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside...

  • Page 244

    Putting up the soft top note: be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “door frame” in this section for further information. 2. Undo the straps used to sec...

  • Page 245

    5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward. 6. Ensure that the top locks into the sunrider 威 locking mechanisms that are located above the front of the rear doors. 7. Unclip and move the sun visors to the side. 3 understanding the features of yo...

  • Page 246

    8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. 9. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 10. If the swing gate brackets were removed, install them by hooking the rear...

  • Page 247

    Over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the shortened rail edge. 11. Ensure that the straps are positioned correctly before pulling the sail panels over the rear roof bow (4–bow). Partially install the sail panel...

  • Page 248

    Roof bow (4–bow) will aid in reaching the channel with the retainers. 12. To install the side windows, affix the window tem- porarily by attaching it to the velcro 威 in the upper rear corner. Start the zipper but close only about 1 in (2.5 cm). 246 understanding the features of your vehicle.

  • Page 249

    13. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 1 — incorrect insertion 2 — correct insertion 3 understanding the featur...

  • Page 250

    14. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro 威 along the top and rear of the window. Repeat this step for the opposite side. 24...

  • Page 251

    15. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. 16. Install the rear window by starting both zipper ends at the lower left ...

  • Page 252

    18. Grasp the swing gate bar and position it into the swing gate brackets. 19. Insert the rear window retainer into the swing gate bracket on both the left and right sides. 20. Complete the installation of the sail panel by insert- ing the rest of the retainer into the body channel. 250 understandin...

  • Page 253

    21. Close the header latches and return the sun visors to their secured position. Sunrider 姞 (two-door models) — if equipped caution! Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. Note: if you are going to be driving ...

  • Page 254

    Opening the sunrider 姞 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Slide the plastic sleeve forward. 4. Grasp the header and lift the top back. Make sure the material is folded back as shown. 252 understanding the features o...

  • Page 255

    Note: the sunrider 威 latch on the door rail should not be activated for sunrider 威 use. If activated, the soft top must be reinstalled starting from the sail panels. 5. Locate the straps to secure the side bows. Wrap the straps around the bows as shown. Repeat on the other side. 6. Reposition the su...

  • Page 256

    Closing the sunrider 姞 1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the front of the vehicle. 4. Hook the header latches to the loops on the wind- shield frame, close latches, and return the sun visors to their origi...

  • Page 257

    Opening the sunrider 姞 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Grasp the front side bow behind the header, and lift the top. 3 understanding the features of your vehicle 255.

  • Page 258

    4. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 5. Fold the top so that the material forms a ⬙w⬙ as shown. Enter the vehicle and move the material into two folds. 256 understanding the features of your vehicle.

  • Page 259

    6. Secure the top by using the two provided straps. Each strap will wrap around the side bow and velcro 威 to itself; use one strap on each side of the vehicle. Closing the sunrider 姞 perform the above steps in the opposite order. Note: failure to fold the fabric rearward will allow the material to s...

  • Page 260

    Raise the windshield and reinstall the side bars as soon as the task that required their removal is completed and before you return to on-road driving. Both you and your passenger should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down...

  • Page 261

    Lowering the windshield and removing side bars 1. Lower the fabric top or remove the hard top following the instructions in this manual. Note: to assist in properly reinstalling side bars, mark the original locations prior to removing. 2. Remove the two top hex bolts (13 mm), and the one side hex bo...

  • Page 262

    7. Remove the one hex bolt (13 mm) visible through the plastic trim on the bottom side of the side bar, one hex bolt (13 mm) on the side of the side bar, and one hex bolt (13 mm) on top of the side bar. Note: pull side bar out horizontally when removing. Caution! Do not remove the head impact foam f...

  • Page 263

    Warning! You or others could be injured if you carry the side bars loose in your vehicle. Remove the side bars from the vehicle or securely store them as described or they may cause personal injury if an accident occurs. See your authorized dealer for the cinch straps. 10. Remove the windshield wipe...

  • Page 264

    13. Secure the windshield by passing a cinch strap through the footman hoop on the center of the hood and on the center of the windshield frame. Tighten the strap to secure the windshield in place. Raising the windshield and replacing side bars 1. Raise the windshield. 2. Loosely attach the rear of ...

  • Page 265

    4. Tighten all side bar attachment bolts. 5. Install the lower windshield plates with the six black round-headed torx 威 head screws (using a #40 torx威 head driver) on each side of the base of the windshield. 6. Reinstall the wiper arms. 3 understanding the features of your vehicle 263.

  • Page 266

    Rear window features — hard top only rear window wiper/washer — if equipped a rotary switch on the center portion of the control lever (located on the right side of the steering column) controls the operation of the rear wiper/washer function. Rotate the switch upward to the first detent posi- tion ...

  • Page 267

    Rear window defroster — if equipped the rear window defroster button is located on the bottom right-side of the blower control knob. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster auto...

  • Page 269: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . . . . . . . 270 䡵 instrument cluster . . . . . . . . . . . . . . . . . . . . 271 䡵 instrument cluster descriptions . . . . . . . . . . . 272 䡵 compass and trip computer — if equipped . . 286 ▫ control buttons ...

  • Page 270

    ▫ system status . . . . . . . . . . . . . . . . . . . . . . . 301 ▫ personal settings (customer-programmable features) . . . . . . . . . . . . . . . . . . . . . . . . . . 301 䡵 media center 230 (req) — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) . . . . . . . . . . . . . . . . . ...

  • Page 271

    䡵 media center 130 with satellite radio (sales code res+rsc) . . . . . . . . . . . . . . . . . . . . . . . 333 ▫ operating instructions — radio mode . . . . . 334 ▫ operation instructions — cd mode for cd and mp3 audio play . . . . . . . . . . . . . . . . . 339 ▫ notes on playing mp3 files . . . . ....

  • Page 272

    Instrument panel features 1 — air outlet 7 — climate controls 2 — instrument cluster 8 — power outlet 3 — radio 9 — lower switch bank 4 — assist handle 10 — power mirror switch — if equipped 5 — glove compartment 11 — horn 6 — power window switches 270 understanding your instrument panel.

  • Page 273

    Instrument cluster 4 understanding your instrument panel 271.

  • Page 274

    Instrument cluster descriptions 1. Fuel gauge the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. 2. Charging system light this light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first ...

  • Page 275

    The driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the seat belt reminder light will flash or remain on continuously. Refer to “occupant restraints” in “things to know before starting your vehicle” for further inf...

  • Page 276

    11. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system...

  • Page 277

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the anti-lock brake system (abs), are also equipped with el...

  • Page 278

    13. Air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. R...

  • Page 279

    17. Vehicle security light — if equipped this light will flash at a fast rate for approxi- mately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. 18. Temperature gauge the temperature gauge shows engine coolant tempera- ture. Any readi...

  • Page 280

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see “main- taining your vehicle”. Follow the warni...

  • Page 281

    Has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) as an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illum...

  • Page 282

    Tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the tpms to continue to function properly. Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped...

  • Page 283

    Vehicle odometer messages when the appropriate conditions exist, the following odometer messages will display: eco . . . . . . . . . . . . . . . . . . . . . . Fuel saver indicator door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door ajar gate . . . . . . . . . . . . . . . . . . . . . ...

  • Page 284

    Caution! Continuous driving with the transmission tempera- ture “hotoil” warning message illuminated will eventually cause severe transmission damage or transmission failure. Warning! If the transmission temperature “hotoil” warn- ing message is illuminated and you continue operat- ing the vehicle, ...

  • Page 285

    Means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the on/run position. To turn off the message temporarily, press and release the trip odometer button on the ins...

  • Page 286

    Caution! Prolonged driving with the mil on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warning! A malfunctioning catalytic ...

  • Page 287

    • each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. • the esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation...

  • Page 288

    30. Electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected while the engine is run- ning, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition key when the ve...

  • Page 289

    Located on the lower left part of the cluster below the speedometer. Control buttons the compass/temperature control buttons are located on the left spoke of the steering wheel. Press and release the step button on the steering wheel to access the options in the compass display. Note: the system wil...

  • Page 290

    Displayed temperature; therefore, temperature readings are not updated when the vehicle is not moving. The following displays can be reset or changed: • compass/temperature • avg eco (changes to present fuel economy) • et (will reset display) • dte (distance to empty) these messages can be cycled th...

  • Page 291

    • magnetic materials should be kept away from the top of the center of the instrument panel. This is where the compass sensor is located. To set the variance start the engine and leave the transmission gear selector lever in the park position. Press and hold the reset button on the steering wheel (f...

  • Page 292

    2. Press and hold the reset button (for approximately 10 seconds) until the current variance zone number is displayed. 3. Release the reset button, then press and hold again for approximately 10 seconds, until the direction is displayed, with the cal indicator on continuously in the display. 4. To c...

  • Page 293

    Trip conditions trip odometer (odo) / eco (fuel saver indicator) — if equipped this display shows the distance traveled since the last reset. Press and release the right button (on the instru- ment cluster) to switch from odometer to trip a or trip b or to eco. Press and hold the right button while ...

  • Page 294

    Eco (fuel saver indicator) — if equipped the eco indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify driving habits in order to increase fuel economy. Electronic vehicle information center (evic) — if equipped the electronic vehicle information center ...

  • Page 295

    • outside temperature (°f or °c) • eco display • fuel economy • miles/kilometers to empty • timer • display units selection • system warnings (door ajar, etc.) • personal settings (customer-programmable features) the system allows the driver to select information by pressing the following buttons mo...

  • Page 296

    Main menu the evic will advance to the first item in the main menu with the next menu button press and release. Compass button press and release the compass button to return to the compass/outside temperature/ audio information/eco screen whenever the current display is not the compass/outside tempe...

  • Page 297

    • right front turn signal lamp out (with a single chime) • right rear turn signal lamp out (with a single chime) • key fob battery low (with a single chime) • personal settings not avail. – vehicle not in park — automatic transmission • personal settings not avail. – vehicle in motion — manual trans...

  • Page 298

    Unless reset, this message will continue to display each time you turn the ignition switch to the on position. To turn off the message temporarily, press and release the menu button. To reset the oil change indicator system (after performing the scheduled maintenance), perform the following procedur...

  • Page 299

    When the select button is pressed, the selected feature will reset and reset all will display next to the select button graphic. Pressing select a second time will reset both average fuel economy and elapsed time. After three seconds without pressing select, reset all will return to reset and only t...

  • Page 300

    Also calibrate the compass by completing one or more 360–degree turns (in an area free from large metal or metallic objects) until the “cal” message displayed in the evic turns off. The compass will now function normally. Note: a good calibration requires a level surface and an environment free from...

  • Page 301

    Set, the compass will automatically compensate for the differences and provide the most accurate compass head- ing. Note: magnetic materials should be kept away from the top of the instrument panel; this is where the compass sensor is located. To change the compass variance: 1. Turn the ignition swi...

  • Page 302

    Display). Upon reset, the history information will be erased, and the averaging will continue from the last fuel average reading before the reset. Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a...

  • Page 303

    Evic units selection (units in display) displays the units used for the outside temperature, average fuel economy and distance to empty features. Press and release the select button to toggle units between ⬙u.S.⬙ and ⬙metric⬙. System status displays system ok if there are no active warning messages ...

  • Page 304

    Auto unlk on exit when on is selected, all doors will unlock when the vehicle is stopped and the transmission is in the park or neutral position and the driver’s door is opened. To make your selection, press and release the select button until “on” or “off” appears. Rke unlock when driver door 1st p...

  • Page 305

    When exiting the vehicle. To make your selection, press and release the select button until “0,” “30,” “60,” or “90” appears. Headlamps with wipers (available with auto headlights only) when on is selected, and the headlight switch is in the auto position, the headlights will turn on approxi- mately...

  • Page 306

    Hill start assist (hsa) — if equipped when on is selected, the hsa system is active. Refer to “electronic brake control system” in “starting and operating” for system function and operating informa- tion. To make your selection, press and release the select button until “on” or “off” appears. Displa...

  • Page 307

    Media center 230 (req) — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power s...

  • Page 308

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Scan button pressing the scan button causes the tuner to search for the next listenable stat...

  • Page 309

    Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the mi...

  • Page 310

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 311

    Program type 16-digit character display classic rock cls rock college college country country foreign language language information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk r...

  • Page 312

    Setup button pressing the setup button allows you to select between the following items: note: turn the tune/scroll control knob to scroll through the entries. Push the audio/select button to select an entry and make changes. • dvd enter - when the disc is in dvd menu mode, selecting dvd enter will ...

  • Page 313

    • ves™ lock - locks out rear ves™ remote controls (if equipped). • ves™ ch1/ch2 - allows the user to change the mode of either the ir1 or ir2 wireless headphones by pressing the audio/select button (if equipped). • set home clock - pressing the select button allows you to set the clock. Turn the tun...

  • Page 314

    The tune/scroll control knob to scroll up and down to select the number and then push to select. Subtitles — if equipped selecting this item allows you to choose between subtitle off or on. Audio drc — if equipped selecting this item allows you to limit maximum audio dynamic range. The default is se...

  • Page 315

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am, 12 fm, and 12 satellite (if equipped...

  • Page 316

    Note: the ignition switch must be in the on or acc position to operate the radio. Load button — loading compact disc(s) press the load button and the pushbutton with the corresponding number (1-6) where the cd is being loaded. The radio will display please wait and prompt when to insert disc. After ...

  • Page 317

    Scan button (cd mode) press the scan button to scan through each track on the cd currently playing. Time button (cd mode) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode) press and hold ff (fast forward) and the cd playe...

  • Page 318

    The radio uses the following limits for file systems: • maximum number of directory levels: 8 • maximum number of files: 255 • maximum number of folders: 100 • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙.⬙ and a three- character extension) • level 2: 31 ...

  • Page 319

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specification sampling fre- quency (khz) bit rate (kbps) wma 44.1 and 48...

  • Page 320

    List button (disc mode for mp3/wma play) pressing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pressing the tune/scroll control knob will begin playing the files contained in that...

  • Page 321

    Scan button (auxiliary mode) no function. Eject button (auxiliary mode) no function. Time button (auxiliary mode) press the time button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Rw/ff (auxiliary mode) no function. Set button (auxil...

  • Page 322

    Macrovision this product incorporates copyright protection technol- ogy that is protected by u.S. Patents and other intellec- tual property rights. Use of this copyright protection technology must be authorized by macrovision, and is intended for home and other limited viewing uses only, unless othe...

  • Page 323

    Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic serial number/sirius identification number (esn/sid). 2. Your vehicle identification number. To access the esn/sid, refer to the following steps: esn/sid ac...

  • Page 324

    • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or along tall buildings can cause intermittent reception. • placing objects over or too close to the antenna can cause signal blockage. Operating instructions - uconnect™ multimedia (satellit...

  • Page 325

    Tune control (rotary) turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the channel. Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob with...

  • Page 326

    You may add a second channel to each pushbutton by repeating the above procedure with this exception: press the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2. This allows a total of 12 satellite channels to be stored into pushbutton memory. Th...

  • Page 327

    Media center 130 (sales code res) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume co...

  • Page 328

    To seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. Time button press the time button to alternate display of the time and radio frequency. Clo...

  • Page 329

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 330

    Set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these butt...

  • Page 331

    If you insert a disc with the ignition on/run and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player wil...

  • Page 332

    Rw/ff press and hold the ff (fast forward) button and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am/fm button press the button to select either am or fm mode. Set/rnd button (random play but...

  • Page 333

    • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name, and will assign a number instead. With a maximum number of files, exc...

  • Page 334

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and a...

  • Page 335

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the dis...

  • Page 336

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 337

    Phone button uconnect™ phone — if equipped press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in “under- standing the features of your vehicle”. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with...

  • Page 338

    Info button press the info button for an rds station (one with call letters displayed). The radio will return a radio text message broadcast from an fm station (fm mode only). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the directi...

  • Page 339

    Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program for...

  • Page 340

    Program type 16-digit character display soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected mu...

  • Page 341

    Window. Select the button (1–6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the set/ rnd button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to e...

  • Page 342

    Inserting compact disc(s) gently insert one cd into the cd player with the cd label facing up. The cd will automatically be pulled into the cd player and the cd icon will illuminate on the radio display. If a cd does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and mu...

  • Page 343

    Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pressing and holding the seek ...

  • Page 344

    Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded using formats other than iso 9660 level 1 and level 2, the radio may fail to read files properly and may be unable to play...

  • Page 345

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 346

    Loading times for playback of mp3 files may be affected by the following: • media - cd-rw media may take longer to load than cd-r media • medium formats - multisession discs may take longer to load than non-multisession discs • number of files and folders - loading times will increase with more file...

  • Page 347

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the aux but...

  • Page 348

    Information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www.Siriuscanada.Ca for canadian residents. Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic seria...

  • Page 349

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 350

    Additional three seconds will make the radio display the song title all of the time (press and hold again to return to normal display). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) tu...

  • Page 351

    Set button – to set the pushbutton memory when you are receiving a channel that you wish to commit to pushbutton memory, press the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a butt...

  • Page 352

    This feature allows an ipod 威 or external usb device to be plugged into the usb port, located in the center console. Ipod 威 control supports mini, 4g, photo, nano, 5g ipod威 and iphone 威 devices. Some ipod威 software versions may not fully support the ipod 威 control features. Please visit apple’s webs...

  • Page 353

    Once the audio device is connected and synchronized to the vehicle’s ipod 威/usb/mp3 control system (ipod威 or external usb device may take a few minutes to connect), the audio device starts charging and is ready for use by pressing radio switches, as described below. Note: if the audio device battery...

  • Page 354

    Mode. In play mode, the following buttons on the radio faceplate may be used to control the ipod 威 or external usb device and display data: • use the tune control knob to select the next or previous track. • turning it clockwise (forward) by one click, while playing a track, skips to the next track ...

  • Page 355

    • press the scan button to use ipod威/usb/mp3 de- vice scan mode, which will play the first 10 seconds of each track in the current list and then forward to the next song. To stop scan mode and start playing the desired track, when it is playing the track, press the scan button again. During scan mod...

  • Page 356

    • during all list modes, the ipod威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backward (counterclockwise) to get to the track faster. • in list mode, the radio preset buttons are used as shortcuts to the following lists on the ipod 威 o...

  • Page 357

    Caution! • leaving the ipod威 or external usb device (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufactur- er’s guidelines. • placing items on the ipod威 or external usb device, or connections to the ipod 威...

  • Page 358

    2. After the ⬙ready⬙ prompt and the following beep, say ⬙setup⬙, then ⬙select audio devices⬙. 3. Say the name of the audio device or ask the uconnect™ phone system to list audio devices. Next track use the seek up button, or press the vr button on the radio and say “next track” to jump to the next t...

  • Page 359

    The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will ...

  • Page 360

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 361

    Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and inner push knobs. Blower control rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control...

  • Page 362

    Note: if your air conditioning performance seems lower than expected, check the front of the a/c con- denser located in front of the radiator for an accumula- tion of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors m...

  • Page 363

    Floor air is directed through the floor outlets with a small amount flowing through the defrost and side window demist outlets. Mix air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the windshiel...

  • Page 364

    Because of moisture buildup inside the vehicle. Select the outside air position for maximum defogging. • the a/c will engage automatically to prevent fogging when the recirculation button is pressed and the mode control is set to panel or panel / floor. • the a/c can be deselected manually without d...

  • Page 365

    Automatic temperature control (atc) — if equipped automatic operation the automatic temperature control system automati- cally maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. Operation of the system is quite simple. 1. Turn the mode contro...

  • Page 366

    The recommended setting for maximum comfort is 72°f (22°c) for the average person; however, this may vary. Note: • the temperature setting can be adjusted at anytime without affecting automatic operation. • pressing the air conditioning control button while in auto mode will cause the led in the con...

  • Page 367

    4 understanding your instrument panel 365.

  • Page 368

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Note: the center in...

  • Page 369

    • air conditioner control press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Press this but- ton a second time to turn off the air conditionin...

  • Page 370

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pressing the recirculation button. However, under certain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the re...

  • Page 371

    Window fogging interior fogging on the windshield can be quickly re- moved by turning the mode selector to defrost. The defrost/floor mode can be used to maintain a clear windshield and provide sufficient heating. If side win- dow fogging becomes a problem, increase blower speed. Vehicle windows ten...

  • Page 372

    Control setting suggestions for various weather conditions 370 understanding your instrument panel.

  • Page 373: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . . . . . 376 ▫ manual transmission – if equipped . . . . . . . 376 ▫ automatic transmission – if equipped . . . . . 376 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 377 ▫ extreme cold weather (below –...

  • Page 374

    䡵 four–wheel drive operation (command- trac i 威 or rock-trac威). . . . . . . . . . . . . . . . . . . 394 ▫ operating instructions/precautions . . . . . . . 394 ▫ shift positions . . . . . . . . . . . . . . . . . . . . . . 396 ▫ shifting procedure . . . . . . . . . . . . . . . . . . . 397 䡵 trac-lok威 ...

  • Page 375

    ▫ brake assist system (bas) . . . . . . . . . . . . . . 423 ▫ hill start assist (hsa) . . . . . . . . . . . . . . . . 423 ▫ electronic roll mitigation (erm) . . . . . . . . . 427 ▫ electronic stability control (esc) . . . . . . . . . 428 ▫ esc activation/malfunction indicator light and esc off indic...

  • Page 376

    䡵 tire chains . . . . . . . . . . . . . . . . . . . . . . . . . . 454 䡵 tire rotation recommendations . . . . . . . . . . . 455 䡵 tire pressure monitor system (tpms) . . . . . . . 456 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . 459 ▫ general information . . . . . . . . . . . . . . ...

  • Page 377

    䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . 486 ▫ towing this vehicle behind another vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486 ▫ recreational towing – four-wheel drive models . . . . . . . . . . . . . . . . . . . . . . . . . . . 487 5 star...

  • Page 378

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to...

  • Page 379

    Normal starting note: normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. Turn the ignition switch to the start position and release when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the lo...

  • Page 380

    Warning! (continued) • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. If the ve...

  • Page 381

    If the engine shows no sign of starting after two 15– second periods of cranking with the accelerator pedal held to the floor, repeat the “normal starting” or “ex- treme cold weather” procedures. With tip start – automatic transmission only if the engine fails to start after you have followed the “n...

  • Page 382

    Warning! Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 volt ac electrical cord could cause electrocution. Manual transmission — if equipped warning! You or others could be injured if you leave the vehicle unattended without having the parking brake fully a...

  • Page 383

    Shifting fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. You should always use first gear when starting from a standing position. Recommended vehicle shift speeds to utilize your manual transmission efficiently for both fuel e...

  • Page 384

    Downshifting moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills. In addition, downshifting at the right time provides better acceleration when you desire to resume speed. Downshift progressively. Do not skip gears to avoid overspeeding the en...

  • Page 385

    Manual transmission downshift speeds in mph (km/h) gear selec- tion 6 to 5 5 to 4 4 to 3 3 to 2 2 to 1 maxi- mum speed 80 (129) 70 (113) 50 (81) 30 (48) 15 (24) note: vehicle speeds shown in the chart above are for 2h and 4h only, vehicle speeds in 4l would be signifi- cantly less. Reverse shifting ...

  • Page 386

    Caution! (continued) • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle speed. • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting into any gear, make sure your foot is firmly pressi...

  • Page 387

    Warning! (continued) • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others ...

  • Page 388

    Brake/transmission shift interlock system this vehicle is equipped with a brake transmission shift interlock system (btsi) that holds the shift lever in the park position unless the brakes are applied. To move the shift lever out of the park position, the ignition switch must be turned to the on/run...

  • Page 389

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use park while the vehicle is in motion. Apply the parking brake when le...

  • Page 390

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move...

  • Page 391

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, and remove the ignition ke...

  • Page 392

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 393

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 394

    Transmission limp home mode transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, transmission limp home mode is activated. In this mode, the transmission remains in the current gear until the vehicle is brough...

  • Page 395

    Lever is in the drive position. For example, if you shift the transmission into 3 (third gear), the transmission will never shift above third gear, but will shift down into second and first gear normally. You can switch between drive and ers mode at any vehicle speed. When the shift lever is in the ...

  • Page 396

    Overdrive operation the automatic transmission includes an electronically controlled overdrive (fifth gear). The transmission will automatically shift into the overdrive gear if the follow- ing conditions are present: • the shift lever is in the drive position, • vehicle speed is sufficiently high, ...

  • Page 397

    Front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed. This is accom- plished by simply moving the shift lever to one of these positions. The 4h and 4l positions are intended for loose, slippery road surfaces only and not intended for normal driving. Driv...

  • Page 398

    Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the n (neutral) position without first fully engaging the parking brake. The transfer case n (neutral) position disengages both the front and rear driveshaft from the powertrain, and will allow the ...

  • Page 399

    Speed. This range (4l) provides additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). The “4wd indicator light” (located in the instrument cluster) will illuminate when the transfer case is shifted into the 4l position. Note: when in 4w...

  • Page 400

    Warning! Failure to engage a position completely can cause transfer case damage or loss of power and vehicle control. You could have a collision. Do not drive the vehicle unless the transfer case is fully engaged. Trac-lok 姞 rear axle — if equipped the trac-lok 威 rear axle provides a constant drivin...

  • Page 401

    This feature will only activate when the following con- ditions are met: • key in ignition, vehicle in 4l (low) range. • vehicle speed should be 10 mph (16 km/h) or less. To activate the system, press the bottom of the axle lock switch once to lock the rear axle only (the “rear axle lock indicator l...

  • Page 402

    Electronic sway bar disconnect — if equipped your vehicle may be equipped with an electronic discon- necting stabilizer/sway bar. This system allows greater front suspension travel in off-road situations. This system is controlled by the sway bar switch located on the instrument panel (to the left o...

  • Page 403

    When activation conditions are not met. The stabilizer/ sway bar should remain in on-road mode during normal driving conditions. Warning! Do not disconnect the stabilizer bar and drive on hard-surfaced roads or at speeds above 18 mph (29 km/h); you may lose control of the vehicle, which could result...

  • Page 404

    Warning! If the stabilizer/sway bar will not return to on-road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury. Contact your loca...

  • Page 405

    2. Remove one bolt from the underside of the vehicle. 3. Remove the side step assembly. 5 starting and operating 403.

  • Page 406

    The basics of off-road driving you will encounter many types of terrain driving off- road. You should be familiar with the terrain and area before proceeding. There are many types of surface conditions: hard-packed dirt, gravel, rocks, grass, sand, mud, snow and ice. Every surface has a different ef...

  • Page 407

    Is needed. Vehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4l (low) range. Caution! Do not use 4l (low) range when operating the vehicle on dry pavement. Driveline hardware dam- age can result. Simultaneous brake and throttle operation many off-road driving conditions require ...

  • Page 408

    Mud deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use second gear (manual transmission), or drive (automatic transmission), with the transfer case in the 4l (low) position to maintain your momentum. If you start to slow to a stop, try turn...

  • Page 409

    Crossing obstacles (rocks and other high points) while driving off-road, you will encounter many types of terrain. These varying types of terrain bring different types of obstacles. Before proceeding, review the path ahead to determine the correct approach and your ability to safely recover the vehi...

  • Page 410

    Caution! • never attempt to straddle a rock that is large enough to strike your axles or undercarriage. • never attempt to drive over a rock which is large enough to contact the door sills. Crossing a ravine, gully, ditch, washout or rut when crossing a ravine, gully, ditch, washout or a large rut, ...

  • Page 411

    Caution! Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high-centered. Getting high-centered if you get hung up or high-centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is c...

  • Page 412

    Recover the vehicle if something goes wrong? If every- thing looks good and you feel confident, shift the trans- mission into a lower gear with 4l (low) engaged, and proceed with caution, maintaining your momentum as you climb the hill. Driving up hill once you have determined your ability to procee...

  • Page 413

    Confident in your ability to proceed, then make sure you are in 4l (low) and proceed with caution. Allow engine braking to control the descent and apply your brakes, if necessary, but do not allow the tires to lock. Warning! Do not descend a steep grade in neutral. Use vehicle brakes in conjunction ...

  • Page 414

    Warning! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in reverse gear. Never back dow...

  • Page 415

    Caution! • water ingestion into the axles, transmission, trans- fer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components, and your brakes will be less effective once wet and/or...

  • Page 416

    Vehicle recovery. If you are able to determine you can safely cross, than proceed using the low and slow method. Caution! Muddy waters can reduce the cooling system effec- tiveness by depositing debris onto the radiator. Crossing ditches, streams, shallow rivers or other flowing water flowing water ...

  • Page 417

    Always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiato...

  • Page 418

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 419

    Power steering fluid check checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an aut...

  • Page 420

    The parking brake lever is located in the center console. To apply the parking brake, pull the lever up as firmly as possible. To release the parking brake, pull the lever up slightly, press the center button, then lower the lever completely. When the parking brake is applied with the ignition switc...

  • Page 421

    Difficult to move the shift lever out of park. The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never use the park position on an automatic transmission as a substitute for the parking brake. Always apply the parking brake fully when parked to guard ag...

  • Page 422

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic transmission in park, a manual transmission in reverse or first gear. Failure to do so may cause the vehicle to roll and cause dam...

  • Page 423

    The anti-lock brake system pump motor runs during the self-test, and during an abs stop, to provide the regulated hydraulic pressure. The motor pump makes a low humming noise during operation; this is normal. Warning! • pumping of the anti-lock brakes will diminish their effectiveness and may lead t...

  • Page 424

    Note: during severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the anti-lock brake system is functioning. Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes...

  • Page 425

    Controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if tcs and esc ar...

  • Page 426

    The level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill. The system w...

  • Page 427

    The system will only work if the intended direction of the vehicle and vehicle gear match. For example, if the intended direction is forward up a hill and the vehicle is in drive (automatic transmission equipped vehicle), and the activation criteria are met, hsa will activate. Hsa on automatic trans...

  • Page 428

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision wi...

  • Page 429

    (manual transmission) with wheels straight. Apply park- ing brake on manual transmission vehicle. 2. Start the engine. 3. With the engine running, the brake applied, and the clutch out, rotate the steering wheel 180° counterclock- wise from center. 4. Press the esc off switch four times within twent...

  • Page 430

    Note: anytime the esc system is in the “full off” mode, erm is disabled. Refer to electronic stability control (esc) for a complete explanation of the available esc modes. Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift o...

  • Page 431

    • understeer - when the vehicle is turning less than appropriate for the steering wheel position. The “esc activation/malfunction indicator light” (lo- cated in the instrument cluster), starts to flash as soon as the tires lose traction and the esc system becomes active. The “esc activation/malfunct...

  • Page 432

    The esc system has three available operating modes in 4h range. The system has one operating mode in 4l range. Two-wheel drive vehicles and four-wheel drive vehicles in 2h range have two operating modes. 4h range (4wd models) or 2wd models on this is the normal operating mode for esc in 4h and 2wd v...

  • Page 433

    Than esc would normally allow is required to gain traction. To turn esc on again, momentarily press the esc off switch. This will restore the normal “esc on” mode of operation. Note: to improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it ma...

  • Page 434

    Returns but tcs remains off. When the vehicle speed drops below 35 mph (56 km/h), the esc system shuts off. The esc is off at low vehicle speeds in 4l range so that it will not interfere with off-road driving, but the esc function returns to provide the stability feature at speeds above 40 mph (64 k...

  • Page 435

    Vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. The “esc activation/malfunction indicator light” (lo- cated in the instrument cluster) starts to flash as soon as ...

  • Page 436

    Swaying trailer is recognized. No driver action is re- quired. Note that tsc cannot stop all trailers from swaying. Always use caution when towing a trailer and follow the tongue weight recommendations. Refer to “trailer towing” in “starting and operating” for further information. When tsc is functi...

  • Page 437

    Gear approximate hdc set speed 1st 1 mph (1.5 km/h) 2nd 2.5 mph (4 km/h) 3rd 4 mph (6.5 km/h) 4th 5.5 mph (9 km/h) drive 7.5 mph (12 km/h) reverse 1 mph (1.5 km/h) however, the driver can override hdc operation by applying the brake to slow the vehicle down below the hdc control speed. If more speed...

  • Page 438

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 439

    Compact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Ex- ample: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards, and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing char...

  • Page 440

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 441

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 442

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 443

    Tire loading and tire pressure tire placard location tire placard location (two-door models) tire placard location (four-door models) 5 starting and operating 441.

  • Page 444

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loa...

  • Page 445

    Combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the statement “the combined weight of occu- pants and cargo should never exceed xxx kg or xxx lbs” on your vehicle’...

  • Page 446

    444 starting and operating.

  • Page 447

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 448

    Economy improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under-inflation also increases tire rolling resistance resulting in higher fuel consumption. Rid...

  • Page 449

    Tire pressures change by approximately 1 psi (7 kpa) per 12° f (7° c) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter. Example: if garage temperature = 68° f (20° c) and the outside temperature = 32° f (0° c) then the cold tire infla...

  • Page 450

    Radial-ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision. Al- ways use radial tires in sets of four. Never combine them with other types of tires. Cuts and punctures in radial tire...

  • Page 451

    Compact spare tire – if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on the tire and loading information placard located on the driver’s side door opening or on the sidewall ...

  • Page 452

    Your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Limited-use spare – if equipped the limited-use spare tire is for temporary emergency use only. This tire is identified by a label located on the limited-use spare whe...

  • Page 453

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) when you are stuck, and do not let anyone near a spinning wheel no...

  • Page 454

    Life of tire the service life of a tire is dependent upon varying factors including but not limited to: • driving style • tire pressure • distance driven warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result...

  • Page 455

    It is recommended you contact your original equipment or an authorized tire dealer with any questions you may have on tire specifications or capability. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. Warning! • do not use a tire, whee...

  • Page 456

    Warning! (continued) • failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire chains tire c...

  • Page 457

    Caution! (continued) • install chains on the rear wheels as tightly as possible and then retighten after driving about 1 ⁄ 2 mile (0.8 km). • do not exceed 30 mph (48 km/h). • drive cautiously and avoid severe turns and large bumps, especially with a loaded vehicle. • do not drive for prolonged peri...

  • Page 458

    Refer to the “maintenance schedule” for the proper maintenance intervals. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed. The suggested rotation method is the “forward-cross” shown in the following...

  • Page 459

    When the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after a vehicle has not been driven for more than three hours, or driven less than 1 mile (1.6 km) after a three-hou...

  • Page 460

    30 psi (207 kpa), but the “tire pressure monitoring telltale light” will still be on. In this situation, the “tire pressure monitoring telltale light” will turn off only after the tires have been inflated to the vehicle’s recom- mended cold placard pressure value. Caution! • the tpms has been optimi...

  • Page 461

    • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the “tire pressure monitoring telltale light.” • seasonal temperature changes will affec...

  • Page 462

    Occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value. The system will automatically update and the “tire pressure monitoring telltale light” will extinguish once the updat...

  • Page 463

    Off the “tire pressure monitoring telltale light” as long as none of the road tires are below the low pressure warning threshold. • if your vehicle is not equipped with a matching full-size spare wheel and tire assembly, it does not have a tire pressure monitoring sensor in the spare tire. The tpms ...

  • Page 464

    The tire pressure sensors are covered under one of the following licenses: united states . . . . . . . . . . . . . . . . . . . Mrxc4n3mf9 canada . . . . . . . . . . . . . . . . . . . . . . 2546a-c4n3mf9 fuel requirements all engines are designed to meet all emis- sions regulations and provide excell...

  • Page 465

    The manufacturer supports the use of reformulated gaso- line. Properly blended reformulated gasoline will pro- vide excellent performance and durability for the engine and fuel system components. Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol....

  • Page 466

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory more extensive repairs will be required for prolo...

  • Page 467

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by fed- eral law. Using leaded gasoline can impair engine performance, and damage the emission control system. • an out-of-tune engine, or certain fuel or ignition...

  • Page 468

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such ...

  • Page 469

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light (mil)” to illuminate, due to f...

  • Page 470

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas...

  • Page 471

    This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle weight rating (gawr) front and rear, and vehicle identification number (vin). A month-day-hour (mdh) number is included on this label and indicates the month, day, and hour of manufacture. The bar c...

  • Page 472

    Tire size the tire size on the label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim size this is the rim size that is appropriate for the tire size listed. Inflation pressure this is the cold tire inflation pressure for yo...

  • Page 473

    Improper weight distributions can have an adverse affect on the way your vehicle steers and handles, and the way the brakes operate. Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way yo...

  • Page 474

    The recommended way to measure gtw is to put your fully-loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Note: t...

  • Page 475

    Tongue. It typically provides adjustable friction associ- ated with the telescoping motion to dampen any un- wanted trailer swaying motions while traveling. Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some ot...

  • Page 476

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the trailer towing weights (maximum ...

  • Page 477

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6...

  • Page 478

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/manual 3.73 two–door sahara model (4wd) 6,430 lbs (2 916 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 3.73 two–door sahara...

  • Page 479

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/manual 3.73 four–door sportmodel (4wd) 8,242 lbs (3 738 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.6l/ automatic 3.73 four–door spo...

  • Page 480

    Engine/ transmission axle model gcwr (gross combined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/manual 4.10 four–door rubicon model (4wd) 8,406 lbs (3 813 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.6l/ automatic 4.10 four–door ...

  • Page 481

    Trailer and tongue weight always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the gross trailer weight (gtw) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side-to-s...

  • Page 482

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the “tire safety information/tire and loading informa...

  • Page 483

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 484

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized (this requirement may limit the ability to always achieve the 10% to ...

  • Page 485

    − an electronically-actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge-actuated brake system, an electronic brake controller is not required. − trailer brakes are recommended for trailers over...

  • Page 486

    Towing requirements – trailer lights and wiring whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The trailer tow package will include a four–pin wiring harness. Use a factory-approved trailer harness and connec...

  • Page 487

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage. Automatic transmission – if equipped the dr...

  • Page 488

    Cooling system to reduce potential for engine and transmission over- heating, take the following actions: − highway driving reduce speed. − air conditioning turn off temporarily. Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the g...

  • Page 489

    Towing condition wheels off the ground four-wheel drive models dolly tow front not allowed rear not allowed on trailer all ok recreational towing – four-wheel drive models note: the transfer case must be shifted into neu- tral (n), automatic transmission must be shifted into park, and manual transmi...

  • Page 490

    Caution! (continued) • before recreational towing, perform the procedure outlined under “shifting into neutral (n)” to be certain that the transfer case is fully in neu- tral (n). Otherwise, internal damage will result. • towing this vehicle in violation of the above requirements can cause severe tr...

  • Page 491

    1. Bring the vehicle to a complete stop. 2. Turn off the engine. 3. Press and hold the brake pedal. 4. Shift the automatic transmission into neutral or depress the clutch pedal on a manual transmission. 5. Shift the transfer case lever into neutral (n). 6. Start the engine. 7. Shift the transmission...

  • Page 492

    Shifting out of neutral (n) use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake. 3. Reconnect the negative battery cable. 4. Turn the ignition switch to the lock/of...

  • Page 493: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . . . . . . . 492 䡵 if your engine overheats . . . . . . . . . . . . . . . . 492 䡵 jacking and tire changing . . . . . . . . . . . . . . . 493 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . 494 ▫ spare tire...

  • Page 494

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. ...

  • Page 495

    Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling system and turning the a/c off can help remove this heat. • you can also turn the temperature control to maximum he...

  • Page 496

    Warning! (continued) • being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be ra...

  • Page 497

    Note: if you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 50 lbs (23 kg) including the weight of the spare tire. Preparations for jacking 1. Park on a firm, level surface. Avoid ice or slippery areas. Warning! Do not attempt to change a tir...

  • Page 498

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 499

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare tire, jack and tools from the stored location. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while...

  • Page 500

    5. Raise the vehicle by turning the jack screw to the right. Raise the vehicle till the tire is raised from the surface of the road. Minimum tire lift provides maximum stability. Warning! Raising the vehicle higher than necessary can make the vehicle less stable and cause a collision. It could slip ...

  • Page 501

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. 8. Lower the vehicle by turning the jack screw to the left, and remove the jack. 9. Finish tightening the lug nuts. Push down on the wrench while tightening for inc...

  • Page 502

    Warning! A loose tire or jack, thrown forward in a collision or hard stop, could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Road tire installation 1. Mount the road tire on the axle. 2. Install the remaining lug nuts with the cone s...

  • Page 503

    Note: when using a portable battery booster pack follow the manufacturer’s operating instructions and precautions. Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electr...

  • Page 504

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 505

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper c...

  • Page 506

    8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle. If frequent jump-starting is required to start your vehicle you should have ...

  • Page 507

    Note: if your vehicle is equipped with traction con- trol or electronic stability control (esc), turn the system off before attempting to “rock” the vehicle. Caution! • when “rocking” a stuck vehicle by moving be- tween drive and reverse (with automatic transmission) or 1st gear and reverse (with ma...

  • Page 508

    Warning! • chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • stand clear of vehicles when pulling with tow hooks. Tow straps may become disengaged, caus- ing serious injury. Caution! Tow hooks are for emergency use only, to rescue a vehicle ...

  • Page 509

    4. Press and maintain firm pressure on the brake pedal. 5. Using the screwdriver or similar tool, reach into the opening and press and hold the shift lever override. 6. Move the shift lever to neutral. 7. The vehicle may then be started in neutral. 8. Reinstall the shift lever override access cover....

  • Page 510

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the trans- mission and drivetrain are operable, disabled vehicles may also be towed as described under “recreational towing” in the “starting and operating” section. Towin...

  • Page 511

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 512

    Four–wheel drive models the manufacturer recommends towing with all wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly. If flatbed equipment is not available and the transfer case is operable, the...

  • Page 513: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . . . . . 513 䡵 onboard diagnostic system — obd ii . . . . . . 514 ▫ loose fuel filler cap message . . . . . . . . . . . 514 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 514

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . 534 ▫ automatic transmission – if equipped . . . . . 536 ▫ hydraulic clutch fluid – manual transmission . . . . . . . . . . . . . . . . . . . . . . . 538 ▫ manual transmission – if equipped . . . . . . . 538 ▫ transfer case . . . . . . . ....

  • Page 515

    Engine compartment — 3.6l 1 — integrated power module (fuses) 6 — washer fluid reservoir 2 — battery 7 — engine coolant reservoir 3 — engine oil dipstick 8 — air cleaner filter 4 — engine oil fill 9 — coolant pressure cap 5 — brake fluid reservoir 10 — power steering fluid reservoir 7 maintaining yo...

  • Page 516

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 517

    The message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil off. Emissions inspection and maintenance programs in some localities, it may be a le...

  • Page 518

    4. Approximately 15 seconds later, one of two things will happen: a. The mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m...

  • Page 519

    Your vehicle. Refer to these service manuals before attempting any procedure yourself. Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehi...

  • Page 520

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or ...

  • Page 521

    Note: under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, whichever occurs first. Engine oil selection for best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are ap...

  • Page 522

    Engine oil viscosity (sae grade) sae 5w-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil fi...

  • Page 523

    Engine oil filter selection all of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably. Only high quality filters should be used to assure most efficient service. Mopar 威 engine ...

  • Page 524

    Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water. R...

  • Page 525

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 526

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency (epa) and is an ozone-saving product. However, the manufacturer recommends that air condi- tioning service be performed by authorized dealers ...

  • Page 527

    Remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may be present with chattering, mark...

  • Page 528

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 529

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions con- trol device and may seriously reduce engine per- formance and cause serious damage to the engine. • damage to the catalytic converter can r...

  • Page 530

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 531

    Garden hose vertically down the face of the a/c con- denser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leak...

  • Page 532

    Caution! • mixing of engine coolant (antifreeze) other than the specified hoat engine coolant (antifreeze) may result in engine damage and may decrease corrosion protection. If a non-hoat engine cool- ant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with ...

  • Page 533

    Please review these recommendations for using hybrid organic additive technology (hoat) engine coolant (antifreeze). When adding engine coolant (antifreeze): • the manufacturer recommends using mopar威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) or equival...

  • Page 534

    Warning! The warning words do not open hot on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the en- gine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To preve...

  • Page 535

    When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine co...

  • Page 536

    • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Brake system in order to assure brake system performan...

  • Page 537

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid ...

  • Page 538

    Warning! (continued) • do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Automatic transmission – if equipped selection of lubricant it is important that the proper...

  • Page 539

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check check the fluid level while the transmission is at normal operating temperature 180° f (82° c). This...

  • Page 540

    The fluid at approximately 80° f (27° c). If the fluid level is correctly established at 80° f (27° c), it should be between the hot (upper) reference holes when the transmission reaches 180° f (82° c). Remember it is best to check the level at the normal operating temperature. Caution! Be aware tha...

  • Page 541

    Fluid level check check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16 in (4.76 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency of fluid change under normal ope...

  • Page 542

    Drain first remove the fill plug (b), then the drain plug (c). The recommended tightening torque for the drain and fill plugs is 15 to 25 ft lbs (20 to 34 n·m). Caution! When replacing the plugs, do not overtighten them. You could damage them and cause them to leak. Selection of lubricant use only m...

  • Page 543

    Trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect ...

  • Page 544

    • avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8...

  • Page 545

    • use mopar威 touch-up paint or equivalent on scratches or chips as soon as possible. Your authorized dealer has touch-up paint to match the color of your vehicle. Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a m...

  • Page 546

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable and, if used in closed areas, they may cause respiratory harm. Caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage ...

  • Page 547

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use mopar 威 total clean or equivalent, a mild soap solution, or lukewarm water. Do not remove the ...

  • Page 548

    • be especially careful when washing the windows by following the directions for “care of fabric top windows.” washing — use mopar 威 car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles. If extra cleaning is required, use mopar 威 con- vertible cloth top cleaner o...

  • Page 549

    Care of fabric top windows caution! Your vehicle’s fabric top has pliable plastic windows which can be scratched unless special care is taken by following these directions: 1. Never use a dry cloth to remove dust. Instead, use a microfiber towel or soft cotton cloth moistened with cold or warm, clea...

  • Page 550

    Zipper teeth. If a stuck zipper slide is experienced, work the mopar 威 soft top zipper cleaner and lubricant or equivalent into the zipper slide. Several applications may be required before the zipper comes free. 6. Never paste stickers, gummed labels or any tape to the windows. Adhesives are hard t...

  • Page 551

    Cavity cartridge fuse mini fuse description j4 25 amp natural driver door node j5 25 amp natural passenger door node j6 40 amp green anti-lock brake sys- tem (abs) pump/ stability control sys- tem j7 30 amp pink anti-lock brake sys- tem (abs) valve/ stability control sys- tem j8 — — j9 40 amp green ...

  • Page 552

    Cavity cartridge fuse mini fuse description j18 20 amp blue powertrain control module (pcm) trans range j19 60 amp yellow radiator fan j20 30 amp pink front wiper lo/hi j21 20 amp blue front/rear washer j22 — spare m1 15 amp blue center high- mounted stop light (chmsl)/switch stop lamp feed m2 20 am...

  • Page 553

    Cavity cartridge fuse mini fuse description m10 15 amp blue ignition off draw – vehicle entertainment system, satellite digi- tal audio receiver (sdars), dvd, hands-free module, radio, antenna, universal garage door opener, vanity lamp m11 10 amp red (ignition off draw) climate control sys- tem, und...

  • Page 554

    Cavity cartridge fuse mini fuse description m16 10 amp red airbag module m17 15 amp blue left tail/license/ park lamp m18 15 amp blue right tail/park/run lamp m19 25 amp natural auto shut down (asd #1 and #2) m20 15 amp blue cabin compartment node interior light, switch bank m21 20 amp yellow auto s...

  • Page 555

    Cavity cartridge fuse mini fuse description m31 20 amp yellow backup lamps m32 10 amp red airbag controller, tt europe m33 10 amp red powertrain controller m34 10 amp red park assist, climate control system, headlamp wash, compass m35 10 amp red heated mirrors m36 20 amp yellow power outlet cavity c...

  • Page 556

    Caution! (continued) • when replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem i...

  • Page 557

    Exterior lights bulb type backup lamps (2) . . . . . . . . . . . . . . . . . . . . . . . 3157 center high-mounted stop lamp (1). . . . . . . . . L.E.D. Fog lamps . . . . . . . . . . . . . . . . . . . . . . . . . Psx24w front park/turn signal lamps (2) . . . . . . . . . . . . 3157 front side marker l...

  • Page 558

    8. Pull the bulb from the housing. 9. Push connector locking tab to the unlock position. 10. Remove connector from bulb. 11. Push connector onto new bulb base, and push the connector locking tab to the lock position. Caution! Do not touch the new bulb with your fingers. Oil contamination will severe...

  • Page 559

    Front fog lamp 1. Reach under the vehicle to access the back of the front fog lamp. 2. Disconnect the wire harness connector from the front fog lamp connector receptacle. 3. Firmly grasp the bulb by the two latch features and squeeze them together to unlock the bulb from the back of the front fog la...

  • Page 560

    3. Rotate the appropriate socket 1/4 turn counterclock- wise, then remove it from the housing. 4. Pull the bulb straight from the socket to replace. Center high-mounted stop lamp (chmsl) the stop lamp is mounted on a bracket that extends upward from the tailgate behind the spare tire. If service is ...

  • Page 561

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 5 year/100,000 mile formula hoat (hybrid organic additive technology) or equivalent. Engine oil use api certified sae 5w-30 engine oil, meeting the requirements of chrysl...

  • Page 562

    Chassis component fluid, lubricant, or genuine part automatic transmission – if equipped mopar 威 atf+4威 automatic transmission fluid or equivalent licensed atf+4 威 product. Manual transmission – if equipped mopar 威 manual transmission lubricant or equivalent (meeting the re- quirements of chrysler m...

  • Page 563: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . . . . . . 562 ▫ required maintenance intervals . . . . . . . . . . 564 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 564

    Maintenance schedule the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating condition...

  • Page 565

    • change your engine oil more often if you drive your vehicle off-road for an extended period of time. • under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, which- ever comes first. Your authorized dealer will reset the oil change indicator message after ...

  • Page 566

    At each oil change • change the engine oil filter. • inspect the brake hoses and lines. • check the manual transmission fluid level. Caution! Failure to perform the required maintenance items may result in damage to the vehicle. Required maintenance intervals refer to the maintenance schedules on th...

  • Page 567

    8,000 miles (13,000 km) or 6 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). ❏ inspect all door latches for presence of grease, reapply if necessary. O...

  • Page 568

    24,000 miles (39,000 km) or 18 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). ❏ inspect all door latches for presence of grease, reapply if necessary...

  • Page 569

    40,000 miles (65,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). ❏ inspect all door latches for presence of grease, reapply if necessary...

  • Page 570

    56,000 miles (91,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). ❏ inspect all door latches for presence of grease, reapply if necessary...

  • Page 571

    64,000 miles (104,000 km) or 48 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). ❏ inspect all door latches for presence of grease, reapply if necessa...

  • Page 572

    72,000 miles (117,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ inspect all door latches for presence of grease, reapply if necessa...

  • Page 573

    88,000 miles (143,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). ❏ inspect all door latches for presence of grease, reapply if necessa...

  • Page 574

    96,000 miles (156,000 km) or 72 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏ inspect all door latches for presence of grease, reapply if necessa...

  • Page 575

    104,000 miles (169,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). ❏ inspect all door latches for presence of grease, reapply if neces...

  • Page 576

    120,000 miles (195,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏ inspect all door latches for presence of grease, reapply if neces...

  • Page 577

    128,000 miles (208,000 km) or 96 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). ❏ inspect all door latches for presence of grease, reapply if neces...

  • Page 578

    144,000 miles (234,000 km) or 108 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). ❏ inspect all door latches for presence of grease, reapply if nece...

  • Page 579

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • failure to properly inspect and mai...

  • Page 581: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581 ▫ prepare for the appointment . . . . . . . . . . . 581 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 581 ▫ be reasonable with r...

  • Page 582

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 587 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 587 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 587 ▫ temperature grades . . . . . . . . . . . . . . . . . . 58...

  • Page 583

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 584

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 585

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 586

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to reso...

  • Page 587

    If nhtsa receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, nhtsa cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. T...

  • Page 588

    Llc vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. • diagnostic procedure manuals diagnostic procedure manuals are filled with dia- grams, charts and detailed illustrations. These pract...

  • Page 589

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 590

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 591: Index

    Index 10

  • Page 592

    Abs (anti-lock brake system) . . . . . . . . . . . . 275,420 adding engine coolant (antifreeze) . . . . . . . . . . 530 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 466 air cleaner, engine (engine air cleaner filter) . . . 521 air conditioner maintenance . . . . . . . . . . . . ...

  • Page 593

    Auxiliary electrical outlet (power outlet) . . . . . . 166 auxiliary power outlet . . . . . . . . . . . . . . . . . . . 166 axle lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521 keyless transmitter replacemen...

  • Page 594

    Child restraint . . . . . . . . . . . . . . . . . . . . 73,76,80,83 child restraint tether anchors . . . . . . . . . . . . . 78,80 child safety locks . . . . . . . . . . . . . . . . . . . . . . . . 40 child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 cleaning wheels . . . . ....

  • Page 595

    Defroster, rear window . . . . . . . . . . . . . . . . . . . 265 defroster, windshield . . . . . . . . . . . . . . . . 90,361,366 delay (intermittent) wipers . . . . . . . . . . . . . . . . . 160 diagnostic system, onboard . . . . . . . . . . . . . . . . 514 dimmer switch, headlight . . . . . . . . ...

  • Page 596

    Jump starting . . . . . . . . . . . . . . . . . . . . . . . 500 tow hooks . . . . . . . . . . . . . . . . . . . . . . . . . 505 emission control system maintenance . . . . . . . . . 515 engine air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . 521 block heater . . . . . . . . . . . . . . ...

  • Page 597

    Air conditioning . . . . . . . . . . . . . . . . . . . . . 369 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . 520 finish care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541 flashers hazard warning . . . . . . . . . . . . . . . . . . . . . 492 turn signal . . . . . . . . . ...

  • Page 598

    Gas cap (fuel filler cap) . . . . . . . . . . . . 466,468,514 gasoline (fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 462 gasoline, reformulated . . . . . . . . . . . . . . . . . . . 462 gauges coolant temperature . . . . . . . . . . . . . . . . . . 277 fuel . . . . . . . . . . . . . . . ....

  • Page 599

    Holder, cup . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 hood release . . . . . . . . . . . . . . . . . . . . . . . . . . 151 hydraulic clutch fluid . . . . . . . . . . . . . . . . . . . . 538 ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 key . . . . . . . . ...

  • Page 600

    Lap/shoulder belts . . . . . . . . . . . . . . . . . . . . . . . 48 latch (lower anchors and tether for children) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78,80 latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 lead free gasoline . . . . . . . . . . . . . . . ...

  • Page 601

    Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 rear servicing . . . . . . . . . . . . . . . . . . . . . . . 557 rear tail . . . . . . . . . . . . . . . . . . . . . . . . . . . 557 seat belt reminder . . . . . . . . . . . . . . . . . . . 272 security alarm (theft alarm) . . . . ....

  • Page 602

    Electric powered . . . . . . . . . . . . . . . . . . . . . 100 electric remote . . . . . . . . . . . . . . . . . . . . . . 100 outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 vanity . . . . . . . . . . . . . . . . ....

  • Page 603

    Overheating, engine . . . . . . . . . . . . . . . . . . . 277,492 owner’s manual (operator manual) . . . . . . . . . 6,585 paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540 paint damage . . . . . . . . . . . . . . . . . . . . . . . . . . 540 panic alarm . . . . . . . . . . . ....

  • Page 604

    Reformulated gasoline . . . . . . . . . . . . . . . . . . . . 462 refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524 release, hood . . . . . . . . . . . . . . . . . . . . . . . . . . 151 reminder, lights on . . . . . . . . . . . . . . . . . . . . . 155 reminder, seat belt . . . ...

  • Page 605

    Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . 58 reminder . . . . . . . . . . . . . . . . . . . . . . . . . . 272 untwisting procedure . . . . . . . . . . . . . . . . . . 54 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 adjustment . . . . . . . . . . . ....

  • Page 606

    Snow chains (tire chains) . . . . . . . . . . . . . . . . . 454 soft top . . . . . . . . . . . . . . . . . . . . . . . . . . . 198,223 spare tire . . . . . . . . . . . . . . . . . . . . . . . 449,450,494 specifications fuel (gasoline) . . . . . . . . . . . . . . . . . . . . . . 462 oil . . . . . . ....

  • Page 607

    Theft system disarming . . . . . . . . . . . . . . . . . . . . 20 tilt steering column . . . . . . . . . . . . . . . . . . . . . 162 tip start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377 tire and loading information placard . . . . . . 441,442 tire identification number (tin) . ....

  • Page 608

    Trac-lok rear axle . . . . . . . . . . . . . . . . . . . . . . 398 traction control . . . . . . . . . . . . . . . . . . . . . . . . . 422 trailer sway control (tsc) . . . . . . . . . . . . . . . . . 433 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . 471 cooling system tips . . . ...

  • Page 609

    Vehicle certification label . . . . . . . . . . . . . . . . . 468 vehicle identification number (vin) . . . . . . . . . . . . 8 vehicle loading . . . . . . . . . . . . . . . . . . . . . . 442,468 vehicle modifications/alterations . . . . . . . . . . . . . . 9 vehicle storage . . . . . . . . . . . . ...

  • Page 610

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 611

    Chrysler group llc 12jk72-126-ad 4th edition printed in u.S.A..