1. DL manuals
  2. Jeep
  3. Automobile
  4. 2013 Grand Cherokee
  5. Owner's Manual

Jeep 2013 Grand Cherokee Owner's Manual

Other manuals for 2013 Grand Cherokee: Review, User Manual, Owner's Manual
Manual is about: 2013 Grand Cherokee

Summary of 2013 Grand Cherokee

  • Page 1

    Grand cherokee chrysler group llc o w n e r ’ s m a n u a l 20 13 gr and cher ok ee 13wk741-126-ae fifth edition printed in u.S.A. 2 0 1 3.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .5 䡵 how to use this manual . . . . . . . . . . . . . .6 䡵 warnings and cautions . . . . . . . . . . . . . .8 䡵 vehicle identification number . . . . . . . .8 ...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle. It can go places and perform tasks t...

  • Page 7

    Note: after reviewing the owner information, it should be stored in the vehicle for convenient referenc- ing and remain with the vehicle when sold. When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech- nicians and genuine mopar® parts, and ...

  • Page 8

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million a...

  • Page 9

    1 introduction 7.

  • Page 10

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 11

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 1 introduct...

  • Page 13: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .14 ▫ wireless ignition node (win) . . . . . . . . . . . . .14 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 ▫ removing key fob from ignition . . . . . . . . . .16 ▫ key-in-i...

  • Page 14

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . .26 ▫ programming additional transmitters. . . . . . . .27 ▫ transmitter battery replacement . . . . . . . . . . .27 ▫ general information . . . . . . . . . . . . . . . . . . . .29 䡵 remote starting system — if equipped . . . . . . . . . . . ...

  • Page 15

    ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . .63 ▫ supplemental active head restraints (ahr) . . .63 ▫ enhanced seat belt use reminder system (beltalert®) . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ seat belt lock out. . . . . . . . . . . . . . . . . . . . . .68 ▫ seat bel...

  • Page 16

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a wireless ignition node (win) with integral ignition switch. You can insert the key fob into the ignition switch with either side up. Keyless enter-n...

  • Page 17

    Key fob the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key ...

  • Page 18

    To remove the emergency key, slide the mechanical latch at the top of the key fob sideways with your thumb and then pull the key out with your other hand. Note: you can insert the double-sided emergency key into the lock cylinders with either side up. Removing key fob from ignition place the shift l...

  • Page 19

    • the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the off position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “electronic vehi...

  • Page 20

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave a vehicle equipped with keyless enter-n- go™ in the acc or on/run mode. A child could operate power windows, other controls, or move the vehicle. • do not leave children ...

  • Page 21

    Sentry key® the sentry key® immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses the factory-mated key fob with remote ...

  • Page 22

    All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics. Replacement keys note: only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to ...

  • Page 23

    • this device must accept any interference that may be received, including interference that may cause unde- sired operation. Vehicle security alarm — if equipped this vehicle security alarm monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unauthor- ized operation. When...

  • Page 24

    • for vehicles equipped with keyless enter-n-go™, make sure the vehicle ignition system is ⬙off⬙. • for vehicles not equipped with keyless enter-n-go™, make sure the vehicle ignition system is ⬙off⬙ and the key is physically removed from the ignition. 2. Perform one of the following methods to lock ...

  • Page 25

    Note: • the driver’s door key cylinder and the liftgate button on the rke transmitter cannot arm or disarm the vehicle security alarm. • the vehicle security alarm remains armed during power liftgate entry. Pressing the liftgate button will not disarm the vehicle security alarm. If someone enters th...

  • Page 26

    This feature also turns on the approach lighting in the outside mirrors (if equipped). Refer to “mirrors” in “understanding the features of your vehicle” for fur- ther information. The lights will fade to off after approximately 30 seconds or they will immediately fade to off once the ignition switc...

  • Page 27

    To unlock the doors press and release the unlock button on the rke transmitter once to unlock the driver’s door or twice to unlock all doors. The turn signal lamps will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Refer to “keyless enter-n-go™” under “thing...

  • Page 28

    Illuminated approach this feature activates the headlights for up to 90 seconds when the doors are unlocked with the rke transmitter. The time for this feature is programmable on vehicles equipped with the electronic vehicle information center (evic). Refer to “electronic vehicle information center ...

  • Page 29

    Note: the interior lights will turn off if you turn the ignition switch to the acc or on/run position while the panic alarm is activated. However, the exterior lamps and horn will remain on. Programming additional transmitters programming key fobs or rke transmitters may be performed at an authorize...

  • Page 30

    2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. 3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sig...

  • Page 31

    4. To assemble the rke transmitter case, snap the two halves together. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept ...

  • Page 32

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • liftgate/flipper glass closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switc...

  • Page 33

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 34

    • the engine can be started two consecutive times with the rke transmitter. However, the ignition must be cycled by pushing the start/stop button twice (or the ignition switch must be cycled to the on/run position) before you can repeat the start sequence for a third cycle. To exit remote start mode...

  • Page 35

    Note: • for vehicles not equipped with the keyless enter-n- go™ feature, the ignition switch must be in the on/run position in order to drive the vehicle. • for vehicles not equipped with the keyless enter-n- go™ feature, the message “remote start active — insert key and turn to run” will display in...

  • Page 36

    Door locks the power door locks can be manually locked from inside the vehicle by using the door lock knob. To lock each door, push the door lock knob on each door trim panel downward. To unlock the front doors, pull the inside door handle to the first detent. To unlock the rear doors, pull the door...

  • Page 37

    Warning! • for personal security and safety in the event of a collision, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or...

  • Page 38

    If you press the door lock switch while the key fob is in the ignition switch and the driver’s door is open, the doors will not lock. If a rear door is locked, it cannot be opened from inside the vehicle without first unlocking the door. The door may be unlocked manually by raising the lock knob. Au...

  • Page 39

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged (locked). Child-protection door lock location child-protection door lock function 2 things to know before starting your vehicle 37.

  • Page 40

    Note: for emergency exit from the rear seats when the child-protection door lock system is engaged, manually raise the door lock knob to the unlocked position, roll down the window, and open the door using the outside door handle. Keyless enter-n-go™ the passive entry system is an enhancement to the...

  • Page 41

    Note: if “unlock all doors 1st press” is programmed all doors will unlock when you grab hold of the driver’s front door handle. To select between “unlock driver door 1st press” and “unlock all doors 1st press”, refer to “electronic vehicle information center (evic)/personal settings (customer-progra...

  • Page 42

    Preventing inadvertent locking of passive entry rke transmitter in vehicle to minimize the possibility of unintentionally locking a passive entry rke transmitter inside your vehicle, the passive entry system is equipped with an automatic door unlock feature which will function if there is no key fob...

  • Page 43

    Note: if “unlock all doors 1st press” is programmed in evic, all doors will unlock when you push the button on the liftgate. If ⬙unlock driver door 1st press⬙ is programmed in evic, the liftgate will unlock when you press the button on the liftgate for further information, refer to “electronic vehic...

  • Page 44

    Note: • after pressing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • the pas...

  • Page 45

    The power window switches remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. Warning! Never leave children in a vehicle with the key in or near the vehicle, or leave a vehicle with keyless enter-n-go™ in the acc or...

  • Page 46

    To open the window part way, press to the first detent and release it when you want the window to stop. Auto up feature with anti-pinch protection — driver and front passenger door only lift the window switch fully upward to the second detent, release, and the window will go up automatically. To sto...

  • Page 47

    Note: if the window runs into any obstacle during auto up it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. Any impact due to rough road condi- tions may trigger the auto reverse function unexpectedly during auto up. If this hap...

  • Page 48

    Window lockout button the window lockout button on the driver’s door allows you to disable the window controls on the rear doors. To disable the window controls on the rear doors, press the window lockout button. To enable the window controls, press the window lockout button again. Wind buffeting wi...

  • Page 49

    Warning! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Liftgate flipper glass the liftgate flipper glass is also unlocked when the liftgate is...

  • Page 50

    Once the liftgate flipper glass has been opened, connec- tion to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open. Note: if a malfunction to the liftgate latch should occur, an emergency liftgate latch release can be used to open the...

  • Page 51

    To operate the power liftgate manually in the open direction, pull the liftgate handle once to initiate a power cycle and then pull the handle a second time to put liftgate into manual mode. When the liftgate button on the rke transmitter is pressed two times, the turn signals will flash twice to si...

  • Page 52

    • if anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance. • there are also pinch sensors attached to the side of the liftgate. Light pressure anywhere along these strips ...

  • Page 53

    Warning! (continued) • if you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. Do not use the recirculation mode. Gas props support the liftgate in the open position. However, because the gas pressure dro...

  • Page 54

    Please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible. If you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for childr...

  • Page 55

    If a child from 1 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (refer to “child restraints”) you should read the instructions provided with your child restraint to make sure that you...

  • Page 56

    Warning! (continued) • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • supplemen...

  • Page 57

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 58

    Warning! (continued) • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • ...

  • Page 59

    Warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden st...

  • Page 60

    Warning! (continued) • a belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your s...

  • Page 61

    5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retrac- tor will withdraw any slack in the belt. 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latc...

  • Page 62

    3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing. Adjustable upper shoulder belt anchorage in the front seating positions, the shoulder belt can be...

  • Page 63

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing the release button. To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt ancho...

  • Page 64

    All passenger-seating positions with a combination lap/ shoulder belt. Use the automatic locking mode anytime a child safety seat is installed in a seating position that has a belt with this feature. Children 12 years old and under should always be properly restrained in the rear seat. How to engage...

  • Page 65

    Energy management feature this vehicle has a safety belt system with an energy management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on collision. This safety belt system has a retractor assembly that is designed to release webbing in a co...

  • Page 66

    How the active head restraints (ahr) work the occupant restraint controller (orc) determines whether the severity, or type of rear impact will require the active head restraints (ahr) to deploy. If a rear impact requires deployment, both the driver and front passenger seat ahrs will be deployed. Whe...

  • Page 67

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: for more information on properly adjusting and positi...

  • Page 68

    3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 4. The ahr front soft foam and trim half should lock into the back decorative plastic half. 1 — downward movement 2 — rearward movement 3 — final downward movement to engage locking mechanism 66 thi...

  • Page 69

    Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an authorized dealer. Enhanced seat belt use reminder system (beltalert®) beltalert® is a feature in...

  • Page 70

    Unbuckled while traveling at speeds greater than 5 mph (8 km/h), beltalert® will provide both audio and visual notification. The front passenger seat beltalert® is not active when the front passenger seat is unoccupied. Beltalert® may be triggered when an animal or heavy object is on the front passe...

  • Page 71

    Dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the ex- tender and store it. Warning! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when ...

  • Page 72

    Note: the driver and front passenger advanced front air bags are certified to the new federal regulations for advanced air bags. The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severit...

  • Page 73

    Air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolster • driver advanced front air bag • passenger advanced front air bag •...

  • Page 74

    Warning! • no objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • do not put anything on or around the air bag covers or attempt to open them manually. Y...

  • Page 75

    When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental side air bag inflatable curtain (sabic) sabic air...

  • Page 76

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the sab and sabic air bags during deployment could cause you to be severely injured or killed. • should a vehicle rollover occur, the pretensioners and/or sab and sabic ...

  • Page 77

    Always sit upright as possible with your back against the seat back, use the seat belts properly, and use the appropriate sized child restraint, infant restraint or booster seat recommended for the size and weight of the child. Knee impact bolsters the knee impact bolsters help protect the knees of ...

  • Page 78

    The advanced front air bags and supplemental driver and front passenger knee air bags will not deploy in all frontal collisions, including some that may produce sub- stantial vehicle damage — for example, some pole colli- sions, truck underrides, and angle offset collisions. On the other hand, depen...

  • Page 79

    Turns on the air bag warning light, either momentarily or continuously. A single chime will sound if the light comes on again after initial startup. It also includes diagnostics that will illuminate the instru- ment cluster air bag warning light if a malfunction is noted that could affect the air ba...

  • Page 80

    The advanced front air bag gas is vented through the vent holes in the sides of the air bag. In this way, the air bags do not interfere with your control of the vehicle. Supplemental seat-mounted side air bag (sab) inflator units the supplemental seat-mounted side air bags are de- signed to activate...

  • Page 81

    Where the sabic inflates. This especially applies to children. The sabic is only about 3-1/2 in (9 cm) thick when it is inflated. Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an air bag should have deployed. Note: in a ro...

  • Page 82

    Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or all of the following may occur: • the nylon air bag material may sometimes cause abrasions and/or skin redd...

  • Page 83

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 84

    Air bag warning light you will want to have the air bags ready to inflate for your protection in a collision. The air bag warning light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenan...

  • Page 85

    Vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The edr in this vehicle is designed to record such data as: • how various systems in your vehicle were operating; • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if ...

  • Page 86

    Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. There are different sizes and types of restraints for children from newborn size to the ch...

  • Page 87

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 88

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 89

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 90

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 91

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 92

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 93

    Latch positions for installing child restraints in this vehicle lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol 2 things to know before starting your vehicle 91.

  • Page 94

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 95

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchor- ages, use the seat belt to install a child seat in the center position next to a child s...

  • Page 96

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between ...

  • Page 97

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel the...

  • Page 98

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing infant restraint...

  • Page 99

    Vehicles with a center arm rest tether for rearward facing infant seats secured in the center seat position with the vehicle seat belts, the rear center seat position has an armrest tether that secures the arm rest in the upward position. 1. To access the center seat arm rest tether, first lower the...

  • Page 100

    3. Raise the armrest and attach the tether hook to the strap located on the front of the arm rest. To install a latch-compatible child restraint 1. If the selected seating position has a switchable auto- matic locking retractor (alr) seat belt, stow the seat belt, following the instructions below. S...

  • Page 101

    4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 102

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using...

  • Page 103

    Lap/shoulder belt systems for installing child restraints in this vehicle 2 things to know before starting your vehicle 101.

  • Page 104

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restrai...

  • Page 105

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. 2. Pull enough of the seat belt webbing fro...

  • Page 106

    9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. Installing a...

  • Page 107

    Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. If the buckle or the cinching latch plate is too close to the belt path opening of the child restraint, you may have trouble tightening the seat belt. If this happens, discon- nect the latch p...

  • Page 108

    2. To access the top tether strap anchorages behind the rear seat, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchor- ages. Pulling down the carpet floor panel to access top tether strap top tether strap anchorage (located on seatback) 106 things to ...

  • Page 109

    3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If...

  • Page 110

    Warning! The top tether anchorages are not visible until the gap panel is folded down. Do not use the visible cargo tie down hooks, located on the floor behind the seats, to attach a child restraint tether anchor. Installing child restraints using the top tether anchorage — center seating position f...

  • Page 111

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of diff...

  • Page 112

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 113

    Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat b...

  • Page 114

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 115

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 117: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 ▫ inside day/night mirror . . . . . . . . . . . . . . . .122 ▫ automatic dimming mirror — if equipped . . .123 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . .124 ▫ o...

  • Page 118

    ▫ advanced phone connectivity . . . . . . . . . . . .153 ▫ things you should know about your uconnect® phone . . . . . . . . . . . . . . . . .155 ▫ general information . . . . . . . . . . . . . . . . . . .166 䡵 voice command — if equipped . . . . . . .166 ▫ voice command system operation . . . . . ....

  • Page 119

    ▫ easy entry/exit seat . . . . . . . . . . . . . . . . . . .194 䡵 to open and close the hood . . . . . . . . .195 䡵 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197 ▫ headlight switch . . . . . . . . . . . . . . . . . . . . .197 ▫ automatic headlights — if equipped . . . . . . .19...

  • Page 120

    ▫ intermittent wiper system . . . . . . . . . . . . . . .208 ▫ windshield washer operation. . . . . . . . . . . . .208 ▫ mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209 ▫ rain sensing wipers — if equipped . . . . . . . .210 䡵 tilt/telescoping steering column . . .212 䡵 power ti...

  • Page 121

    ▫ adaptive cruise control (acc) menu . . . . . . .230 ▫ display warnings and maintenance . . . . . . . .232 ▫ precautions while driving with acc . . . . . . .236 ▫ general information . . . . . . . . . . . . . . . . . . .239 ▫ normal (fixed speed) cruise control mode . . .239 ▫ forward collision war...

  • Page 122

    ▫ programming a rolling code . . . . . . . . . . . . .262 ▫ programming a non-rolling code . . . . . . . . .264 ▫ canadian/gate operator programming . . . . . .266 ▫ using homelink®. . . . . . . . . . . . . . . . . . . . .267 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . .267 ▫ tr...

  • Page 123

    ▫ closing power shade — express . . . . . . . . . . .275 ▫ closing power shade — manual mode . . . . . .275 ▫ pinch protect feature . . . . . . . . . . . . . . . . . . .275 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . .276 ▫ sunroof maintenance . . . . . . . . . . . . . . . . . . .27...

  • Page 124

    Mirrors inside day/night mirror a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjus...

  • Page 125

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will illuminate to indicate when the dim- ming feature is activated. The m...

  • Page 126

    Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they ...

  • Page 127

    Power mirrors the power mirror switch is located on the driver’s side door trim panel. The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror contro...

  • Page 128

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster if equipped. Some vehicles may not be equipped with rear window defroster, in this case the heated mirrors will still function as intended. Refer t...

  • Page 129

    Sun visor extension — if equipped this feature has a pull out extension on the sun visor for increased coverage. Blind spot monitoring — if equipped the blind spot monitoring (bsm) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (aut...

  • Page 130

    When the vehicle is started, the bsm warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational. The bsm system sensors operate when the vehicle is in any forward gear or reverse and enters stand-by mode when the vehicle is in pa...

  • Page 131

    The bsm system notifies the driver of objects in the detection zones by illuminating the bsm warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “modes of operation” for further information. The bsm system monitors the...

  • Page 132

    Entering from the side vehicles that move into your adjacent lanes from either side of the vehicle. Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Side monitoring rear monitor...

  • Page 133

    Overtaking traffic if you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h)...

  • Page 134

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects t...

  • Page 135

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicles mirrors, glance over your shoulder...

  • Page 136

    Note: in a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When rcp is on and the vehicle is in reverse, the driver is alerted using both the visua...

  • Page 137

    Blind spot alert lights/chime when operating in blind spot alert lights/chime mode, the bsm system will provide a visual alert in the appro- priate side view mirror based on a detected object. If the turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, a...

  • Page 138

    Uconnect® phone — if equipped uconnect® phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect® phone allows you to dial a phone number with your mobile phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s aud...

  • Page 139

    System. Only one linked (or paired) mobile phone can be used with the system at a time. The system is available in english, spanish, or french languages. Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone u...

  • Page 140

    The radio display will be used for visual prompts from the uconnect® phone such as “cell” or caller id on certain radios. Operation voice commands can be used to operate the uconnect® phone and to navigate through the uconnect® phone menu structure. Voice commands are required after most uconnect® p...

  • Page 141

    To activate the uconnect® phone, simply press the button and follow the audible prompts for directions. Uconnect® phone sessions begin with a press of the button on the radio control head. Cancel command at any prompt, after the beep, you can say “cancel” and you will be returned to the main menu. H...

  • Page 142

    • you will then be asked to give your mobile phone a priority level between one and seven, with one being the highest priority. You can pair up to seven mobile phones to your uconnect® phone. However, at any given time, only one mobile phone can be in use, connected to your uconnect® system. The pri...

  • Page 143

    Or downloaded phonebook. To learn how to store a name in the phonebook, refer to “add names to your uconnect® phonebook”, in the phonebook. • the uconnect® system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Phonebook download...

  • Page 144

    • this downloaded phonebook cannot be edited or deleted on the uconnect® phone. These can only be edited on the mobile phone. The changes are trans- ferred and updated to uconnect® phone on the next phone connection. Add names to your uconnect® phonebook note: adding names to the uconnect® phonebook...

  • Page 145

    Edit uconnect® phonebook entries note: • editing names in the phonebook is recommended when the vehicle is not in motion. • automatic downloaded phonebook entries cannot be deleted or edited. • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook edit entry”. ...

  • Page 146

    • after you enter the phonebook delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say “list names” to hear a list of the entries in the phonebook from which you choose. To select ...

  • Page 147

    • the uconnect® phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available. • to call one of the names in the list, press the but- ton during the playing of the desired name, and say “call”. Note: the user can also exercise “edit” or “delete” o...

  • Page 148

    Note: the uconnect® phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making a second call while current call is in progress to make a second call while you are cu...

  • Page 149

    Three-way calling to initiate three-way calling, press the button while a call is in progress, and make a second phone call, as described under “making a second call while current call is in progress”. After the second call has established, press and hold the button until you hear a double beep, ind...

  • Page 150

    • after the ignition key is cycled to off, a call can continue on the uconnect® phone for a certain dura- tion, after which the call is automatically transferred from the uconnect® phone to the mobile phone. • an active call is automatically transferred to the mo- bile phone after the ignition key i...

  • Page 151

    • after the “ready” prompt and the following beep, say “emergency” and the uconnect® phone will instruct the paired mobile phone to call the emergency number. This feature is supported in the u.S., canada, and mexico. Note: • the emergency number dialed is based on the country where the vehicle is p...

  • Page 152

    Note: • the roadside assistance number dialed is based on the country where the vehicle is purchased (1-800-528-2069 for the u.S., 1-877-213-4525 for canada, 55-14-3454 for mexico city and 1-800-712-3040 for outside mexico city in mexico). Please refer to the “roadside assistance” coverage details o...

  • Page 153

    Enter your pin followed with a pound, (3 7 4 6 #), you can press the button and say, “3 7 4 6 # send”. Saying a number, or sequence of numbers, followed by “send”, is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can...

  • Page 154

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G., the uconnect® phone will not repeat a phone number before you dial it). • press the button to begin. • after the “ready” prompt and the following beep, say one of the followi...

  • Page 155

    Mute/un-mute (mute on/off) when you mute the uconnect® phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect® phone: • press the button. • following the beep, say “mute”. In order to un-mute...

  • Page 156

    • when prompted, say “list phones”. • the uconnect® phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “se- lect” or “delete”. Also, see the next two sections f...

  • Page 157

    Things you should know about your uconnect® phone uconnect® phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect® tutorial.” voice training for users experiencing difficulty with the system recogniz- ing their voice commands or numbers, the uconnect® pho...

  • Page 158

    Voice command • for best performance, adjust the rearview mirror to provide at least ½ in (1 cm) gap between the overhead console (if equipped) and the mirror. • always wait for the beep before speaking. • speak normally, without pausing, just as you would speak to a person sitting a few feet/meters...

  • Page 159

    • phonebook (downloaded and uconnect® phone lo- cal) name recognition rate is optimized when the entries are not similar. • numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • you can say “o” (letter “o”) for “0” (zero). • even though international ...

  • Page 160

    Sms uconnect® phone can read or send new messages on your phone. Read messages: if you receive a new text message while your phone is connected to uconnect® phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • press the button. • ...

  • Page 161

    List of preset messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L o l 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See you in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18....

  • Page 162

    Turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and the following beep, say “setup, sms incoming message announcement,” you will then be given a choice to ...

  • Page 163

    3 understanding the features of your vehicle 161.

  • Page 164

    162 understanding the features of your vehicle.

  • Page 165

    3 understanding the features of your vehicle 163.

  • Page 166

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location voice commands primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais 164 understanding ...

  • Page 167

    Voice commands primary alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book voice commands primary alternate (s) previous record again redial return to main menu return or main menu select phone select...

  • Page 168

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 169

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When you press the voice command button, you...

  • Page 170

    To hear the first available menu, press the voice com- mand button and say “help” or “main menu”. Commands the voice command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the volum...

  • Page 171

    Radio am (or radio long wave or radio medium wave — if equipped) to switch to the am band, say “am” or “radio am”. In this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous st...

  • Page 172

    Disc mode to switch to the disc mode, say “disc”. In this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) usb mode to switch to usb mode, s...

  • Page 173

    • “play memos” (to play previously recorded memos) — during the playback you may press the voice com- mand button to stop playing memos. You pro- ceed by saying one of the following commands: – “repeat” (to repeat a memo) – “next” (to play the next memo) – “previous” (to play the previous memo) – “d...

  • Page 174

    Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect® voice “voice training” feature may be used. 1. Press the voice command button, say “system setup” and once you are in that menu then say “voice training.” this will train your...

  • Page 175

    Power seats — if equipped some models may be equipped with eight-way power driver and front passenger seats. The power seat switches are located on the outboard side of the seat. There are two switches that control the movement of the seat cushion and the seatback. Power seat switches 1 — seatback s...

  • Page 176

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 177

    Warning! (continued) • do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Caution! Do not place any article under a power seat or impede its abili...

  • Page 178

    Tilting the seat up or down the angle of the seat cushion can be adjusted up or down. Pull upward or push downward on the front of the seat switch, the front of the seat cushion will move in the direction of the switch. Release the switch when you have reached the desired position. Power lumbar — if...

  • Page 179

    Manual front seats forward/rearward adjustment some models may be equipped with manual front driver or passenger seats. The seats can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor. While sitting in the seat, lift up on the bar located under t...

  • Page 180

    Manual front passenger seatback adjustment — recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the sea...

  • Page 181

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters in both the seat cushions and seatbacks. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus...

  • Page 182

    Vehicles equipped with remote start on models that are equipped with remote start, the driver’s heated seat and heated steering wheel can be programmed to come on during a remote start. Refer to “remote starting system — if equipped” in “things to know before starting your vehicle” for further infor...

  • Page 183

    Rear heated seats on some models, the two outboard seats are equipped with heated seats. There are two heated seat switches that allow the rear passengers to operate the seats indepen- dently. The heated seat switches for each heater are located on the rear of the center console. You can choose from...

  • Page 184

    At that time, the number of illuminated leds changes from two to one, indicating the change. The low-level setting will turn off automatically after approximately 45 minutes. Ventilated seats — if equipped on some models, both the driver and passenger seats are ventilated. Located in the seat cushio...

  • Page 185

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear- impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be...

  • Page 186

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. For comfort the active head restraints can be tilted forward and rearward. To tilt the head restrain...

  • Page 187

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 188

    Warning! (continued) • active head restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the ac- tive head restraint ensure that all cargo is secured, as loose cargo could contact the active head re- straint during sudden st...

  • Page 189

    Warning! Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure the outboard head re- straints are in their upright positions when the seat is to be occupied. Note: for proper routing of a child seat tether refer to ...

  • Page 190

    Note: • do not fold the 60% rear seat down with the left outboard or rear center seat belt buckled. • do not fold the 40% rear seat down with the right outboard seat belt buckled. 2. Fold the rear seat completely forward. To raise rear seat raise the rear seatback and lock it into place. If interfer...

  • Page 191

    Reclining rear seat to recline the seatback, lift the lever located on the outboard side of the seat, lean back and release the lever at the desired position. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the seatback reclined so that the shoul...

  • Page 192

    Note: your vehicle is equipped with two rke trans- mitters. One rke transmitter can be linked to memory position 1 and the other transmitter can be linked to memory position 2. The memory seat switch is located on the driver’s door trim panel. The switch consists of three buttons: • the (s) button, ...

  • Page 193

    Programming the memory feature note: to create a new memory profile, perform the following: vehicles equipped with keyless enter-n-go 1. Without pressing the brake pedal, push the engine start/stop button and cycle the ignition to the on/run position (do not start the engine). 2. Adjust all memory p...

  • Page 194

    Note: • memory profiles can be set without the vehicle in park, but the vehicle must be in park to recall a memory profile. • the recall memory with remote linked to memory feature can be enabled through the electronic vehicle information center (evic), refer to “electronic vehicle information cente...

  • Page 195

    3. Once the profile has been recalled, press and release the set (s) button on the memory switch, then press and release button (1) or (2) accordingly. “memory profile set” (1 or 2) will display in the instrument cluster on vehicles equipped with the evic. 4. Press and release the lock button on the...

  • Page 196

    A recall can be cancelled by pressing any of the memory buttons during a recall (s, 1, or 2). When a recall is cancelled, the driver’s seat, driver’s mirror and the pedals stop moving. A delay of one second will occur before another recall can be selected. Easy entry/exit seat this feature provides ...

  • Page 197

    Note: the easy entry/exit feature is not enabled when the vehicle is delivered from the factory. The easy entry/exit feature is enabled (or later disabled) through the programmable features in the electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)/cu...

  • Page 198

    2. Reach under the hood, move safety latch to the left and lift the hood. Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. Warning! Be sure the hood is fully latched before driving your vehic...

  • Page 199

    Lights headlight switch the headlight switch is located on the left side of the instrument panel, next to the steering wheel. The head- light switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped). To turn on the headlights...

  • Page 200

    Caution! Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses. Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to...

  • Page 201

    Note: when your headlights come on during the day- time, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “lights” in this section for further information. Smartbeam™ — if equipped the smartbeam™ system provides increased forward lighting at night by auto...

  • Page 202

    To deactivate 1. Pull the multifunction lever toward you (or rearward in car) to manually deactivate the system (normal operation of low beams). 2. Push back on the multifunction lever once again to reactivate the system. Daytime running lights — if equipped the daytime running lights (low intensity...

  • Page 203

    The headlight delay time is programmable on vehicles equipped with an electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)/customer-programmable features” in “under- standing your instrument panel” for further information. Parking lights and panel ligh...

  • Page 204

    Interior lights courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the headlight switch) is rotated to the its farthest upward position, or if equipped, when the unlock button is pressed on the remote keyless entry (rk...

  • Page 205

    Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is opened. Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. I...

  • Page 206

    Each light can be turned on by pressing a switch on either side of the console. These buttons are backlit for night time visibility. To turn the lights off, press the switch a second time. The lights will also turn on when the unlock button on the remote keyless entry (rke) is pressed. Courtesy ligh...

  • Page 207

    Ambient light the overhead console is equipped with an ambient light feature. This light casts illumination for improved visibil- ity of the floor center console and prndl area. Multifunction lever the multifunction lever is located on the left side of the steering column. Ambient light multifunctio...

  • Page 208

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside l...

  • Page 209

    Windshield wiper operation rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation. Multifunction lever windshield wiper operation 3 understanding the features of your vehi...

  • Page 210

    Caution! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Intermittent wiper system use one of the...

  • Page 211

    Lever is pushed while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the end of the lever is released, and then resume the intermittent interval previously selected. If the end of the lever is pushed while the wipers are in the off position, the wipers...

  • Page 212

    Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Rain sensing wipers — if equipped this feature senses moisture on the windshield and automaticall...

  • Page 213

    • the rain sensing feature may not function properly when ice, or dried salt water is present on the windshield. • use of rain-x® or products containing wax or silicone may reduce rain sensing performance. • a customer programmable feature in the electronic vehicle information center (evic) allows t...

  • Page 214

    Tilt/telescoping steering column this feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column. To unlock the steering column, pus...

  • Page 215

    Power tilt/telescoping steering column — if equipped this feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The power tilt/telescoping steering column lever is located below the multifunction lever on the steering column...

  • Page 216

    Heated steering wheel — if equipped the steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate for approximately 30 to 95 minutes before automa...

  • Page 217

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures,...

  • Page 218

    Note: in order to ensure proper operation, the electronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off butto...

  • Page 219

    To resume speed to resume a previously set speed, push the res (+) button and release. Resume can be used at any speed above 20 mph (32 km/h). To vary the speed setting when the electronic speed control is set, you can in- crease speed by pushing the res (+) button. If the button is continually pres...

  • Page 220

    Note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without electronic speed control. Warning! Electronic speed control can be dangerous...

  • Page 221

    Warning! • adaptive cruise control (acc) is a convenience system. It is not a substitute for active driving involvement. It is always the driver’s responsibil- ity to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead; and, most importantly, brake ope...

  • Page 222

    Warning! You should switch off the acc system: • when driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.E., in highway construction zones). • when entering a turn lane or highway off ramp; when driving on roads that are winding, icy, snow- covered, slipp...

  • Page 223

    Note: any chassis/suspension modifications to the ve- hicle will effect the performance of the adaptive cruise control. Activating adaptive cruise control (acc) you can only activate acc if the vehicle speed is above 18 mph (30 km/h). When the system is turned on and in the ready state, the electron...

  • Page 224

    Note: you cannot enable acc under the following conditions: • when in four-wheel drive low. • when you apply the brakes. • when the parking brake is set. • when the automatic transmission is in park, re- verse or neutral. • when pushing the res + button without a previously set speed in memory. To a...

  • Page 225

    Warning! Leaving the adaptive cruise control (acc) system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the system off when you are not using it. To set a desired acc speed when...

  • Page 226

    • the system will not be controlling the distance be- tween your vehicle and the vehicle ahead. The vehicle speed will only be determined by the position of the accelerator pedal. To cancel the system will disable acc without erasing the memory if: • you softly tap the brake pedal. • you depress the...

  • Page 227

    Note: if acc is resumed or set with the esc/tcs off, esc will automatically be re-engaged. To turn off the system will turn off and erase the set speed in memory if: • you push the on/off button. • you turn off the ignition. • you switch to four-wheel drive low. To resume speed press the res + butto...

  • Page 228

    Warning! The resume function should only be used if traffic and road conditions permit. Resuming a set speed that is too high or too low for prevailing traffic and road conditions could cause the vehicle to accelerate or decelerate too sharply for safe operation. Failure to follow these warnings can...

  • Page 229

    • the acc system can only apply a maximum of 25% of the vehicle’s braking capability and will not bring the vehicle to a complete stop. • the acc system maintains set speed when driving up hill and down hill. However, a slight speed change on moderate hills is normal. In addition, downshifting may o...

  • Page 230

    To change the distance setting, press the distance button and release. Each time the button is pressed, the distance setting adjusts between long, medium, and short. Distance setting 2 distance setting 1 228 understanding the features of your vehicle.

  • Page 231

    If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same lane, the evic displays the “sensed vehicle indi- cator” icon, and the system adjusts vehicle speed auto- matically to maintain the distance setting, regardless of the set speed....

  • Page 232

    The acc systems provides overtake aid when passing on the left hand side only. When driving with acc engaged and following a target vehicle, the system will provide an additional acceleration based on your current speed. The acceleration is triggered by indicating a left turn signal. Adaptive cruise...

  • Page 233

    Press the menu button (located on the steering wheel) repeatedly until one of the following displays in the evic: adaptive cruise control off – when acc is deactivated, the display will read “adaptive cruise control off.” adaptive cruise control ready – when acc is activated but the vehicle speed se...

  • Page 234

    • driver override • system off • acc proximity warning • acc unavailable warning • the evic will return to the last display selected after five seconds of no acc display activity. Display warnings and maintenance “clean radar sensor in front of vehicle” warning the acc “clean radar sensor in front o...

  • Page 235

    Note: if the acc “clean radar sensor in front of vehicle” warning is active normal (fixed speed) cruise control is still available. For additional information refer to “normal (fixed speed) cruise control mode” in this section. If weather conditions are not a factor, the driver should examine the se...

  • Page 236

    • installing a snow plow, front-end protector, an after- market grille or modifying the grille is not recom- mended. Doing so may block the sensor and inhibit acc operation. Removing acc sensor for off-roading note: when off-roading, it may be advisable to remove the acc sensor. The sensor is locate...

  • Page 237

    A connector plug is stowed on top of the bumper beam. Insert the wiring connector into the connector plug. Note: when the sensor is removed, adaptive cruise control, normal cruise control, and forward collision warning will not be available. The cluster will display the warning “acc/fcw unavailable ...

  • Page 238

    Precautions while driving with acc in certain driving situations, acc may have detection issues. In these cases, acc may brake late or unexpect- edly. The driver needs to stay alert and may need to intervene. Adding a trailer hitch the weight of a trailer/hitch may affect the performance of acc. If ...

  • Page 239

    Using acc on hills when driving on hills, acc may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, acc perfor- mance may be limited. Lane changing acc will not detect a vehicle until it is completely in the lane in which you...

  • Page 240

    Distance to the lane-changing vehicle. Always be atten- tive and ready to apply the brakes if necessary. Narrow vehicles some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There will not be suffi- cient ...

  • Page 241

    General information fcc requirements for vehicular radar systems classification specifications: 47 c.F.R. Part 15 47 c.F.R part 15.515 normal (fixed speed) cruise control mode in addition to adaptive cruise control mode, a normal (fixed speed) cruise control mode is available for cruis- ing at fixed...

  • Page 242

    Warning! In the normal cruise control mode, the system will not react to vehicles ahead. In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to-vehicle distance is ...

  • Page 243

    To resume press the res + button and then remove your foot from the accelerator pedal. The evic will display the last set speed. To turn off the system will turn off and erase the set speed in memory if: • you push the on/off button. • you turn off the ignition. • you engage four-wheel drive low. If...

  • Page 244

    Fcw monitors the information from the forward looking sensor as well as the electronic brake controller (ebc), wheel speed sensors, i.E., to calculate a probable rear-end collision. When the system determines that a rear-end collision is probable a warning message (both audible and visual) will be d...

  • Page 245

    Guard rails or sign posts based on the course predic- tion. This is expected and is a part of normal fcw activation and functionality. Warning! Forward collision warning (fcw) is not intended to avoid a collision on its own, nor can fcw detect every type of collision. The driver has the responsi- bi...

  • Page 246

    Changing the fcw status to the “near” setting, allows the system to warn you of a possible collision with the vehicle in front of you when you are much closer. This setting provides less reaction time than the “far” setting, which allows for a more dynamic driving experience. Changing the fcw status...

  • Page 247

    Note: • the system will retain the last setting selected by the driver after ignition shut down. • fcw will not react to irrelevant objects such as overhead objects, ground reflections, objects not in the path of the car, stationary objects that are far away, oncoming traffic, or leading vehicles wi...

  • Page 248

    Parksense® rear park assist — if equipped the parksense® rear park assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to parksense® system usage precautions for limitations of th...

  • Page 249

    Parksense® warning display the parksense® warning screen will only be displayed if sound and display is selected from the customer- pro- grammable features section of the electronic vehicle information center (evic). Refer to “electronic vehicle information center (evic)/personal settings (customer-...

  • Page 250

    Parksense® display when the vehicle is in reverse, the warning display will turn on indicating the system status. The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the evic display will show few...

  • Page 251

    Slow tone fast tone 3 understanding the features of your vehicle 249.

  • Page 252

    The vehicle is close to the obstacle when the evic display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: continuous tone 250 understanding the features of your vehicle.

  • Page 253

    Warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-39 in (200-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none single 1/2 second tone slow fast continuous arcs none 3 solid (continuous) 3 slow flashing 2 slow flashing 1 slow flashing ...

  • Page 254

    Note: the parksense® system will automatically dis- able when the system detects that a trailer with trailer brakes has been connected to the integrated trailer brake module. The evic will display “parksense off” message for as long as the vehicle is in reverse. The parksense® switch led will be on ...

  • Page 255

    Parksense® system usage precautions note: • ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep the parksense® system oper- ating properly. • jackhammers, large trucks, and other vibrations could affect the performance of parksense®. • when you turn parksense® off, the ins...

  • Page 256

    • on vehicles equipped with a tailgate, parksense® should be disabled when the tailgate is in the lowered or open position and the vehicle is in reverse. A lowered tailgate could provide a false indication that an obstacle is behind the vehicle. Caution! • parksense® is only a parking aid and it is ...

  • Page 257

    Warning! (continued) could detect the ball mount and hitch ball assem- bly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle. Parkview® rear back up camera — if equipped your vehicle may be equipped with the parkview® rear back up camera that allows y...

  • Page 258

    Zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 3 ft (30 cm - 1 m) green 3 ft or greater (1 m or greater) warning! Drivers must be careful when backing up even when using the parkview® rear back up camera. Always check carefully behind your vehicle, and be sure to che...

  • Page 259

    Note: if snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Turning parkview® on or off — with navigation/multimedia radio 1. Press the “menu” hard-key. 2. Select “system setup” soft-key. 3. Press...

  • Page 260

    Overhead console the overhead console contains courtesy/reading lights and storage for sunglasses. Universal garage door opener (homelink®), power liftgate and power sunroof switches may also be included, if equipped. Front map/reading lights lights are mounted in the overhead console. Each light ca...

  • Page 261

    To turn the lights off, press the switch a second time. The lights also turn on when a door is opened. The lights will also turn on when the unlock button on the rke is pressed. Courtesy lights the courtesy lights can be turned on by pressing the top corner of the lens. To turn the lights off, press...

  • Page 262

    Sunglasses bin door at the front of the console a compartment is provided for the storage of a pair of sunglasses. The storage compart- ment access is a “push/push” design. Push the chrome pad on the door to open. Push the chrome pad on the door to close. Garage door opener — if equipped homelink® r...

  • Page 263

    Note: homelink® is disabled when the vehicle secu- rity alarm is active. Homelink® buttons/overhead consoles homelink® buttons/sunvisor/headliner 3 understanding the features of your vehicle 261.

  • Page 264

    Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the d...

  • Page 265

    1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in view. 3. Simultaneously press and hold both the homelink® button you want to program and the hand-h...

  • Page 266

    Firmly press and release the “learn” or “train- ing” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the learn/train mode. Note: you have 30 seconds in which to initiate the next step after the learn button has been pressed. 6. Re...

  • Page 267

    3. Simultaneously press and hold both the homelink® button you want to program and the hand-held trans- mitter button. 4. Continue to hold both buttons and observe the indi- cator light. Homelink® indicator will flash slowly and then rapidly after homelink® has received the frequency signal from the...

  • Page 268

    Canadian/gate operator programming for programming transmitters in canada/united states that require the transmitter signals to “time-out” after several seconds of transmission. Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission ...

  • Page 269

    If you unplugged the garage door opener/device for programming, plug it back in at this time. Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Press and hold the desired homelink® but...

  • Page 270

    Troubleshooting tips if you are having trouble programming homelink®, here are some of the most common solutions: • replace the battery in the original hand-held transmitter. • press the learn button on the garage door opener to complete the training for a rolling code. • did you unplug the device f...

  • Page 271

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 272

    Warning! • never leave children in a vehicle with the key in the ignition switch (or with the ignition in the accessory or on/run position, for vehicles equipped with keyless enter-n-go™). Occupants, particularly unattended children, can become en- trapped by the power sunroof while operating the po...

  • Page 273

    Automatically. This is called “express close”. During express close operation, any movement of the switch will stop the sunroof. Closing sunroof — manual mode to close the sunroof, press and hold the switch in the forward position. Any release of the switch will stop the movement and the sunroof wil...

  • Page 274

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 275

    Warning! • never leave children in a vehicle with the key in the ignition switch (or with the ignition in the accessory or on/run position, for vehicles equipped with keyless enter-n-go™). Occupants, particularly unattended children, can become en- trapped by the power sunroof while operating the po...

  • Page 276

    Opening sunroof — express press the switch rearward and release it within one-half second. The sunroof and sunshade will open automatically from any position. The sunroof and sunshade will open fully and stop automatically. This is called “express open”. During express open operation, any movement o...

  • Page 277

    Opening power shade — manual mode to open the shade, press and hold the switch rearward . The shade will open and stop automatically at the half-open position. Press and hold the shade switch rearward again and the shade will open automatically to the full-open position. Any release of the switch wi...

  • Page 278

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 279

    Electrical power outlets your vehicle is equipped with 12 volt (13 amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is power...

  • Page 280

    The front power outlet is located inside the storage area on the center stack of the instrument panel. Push inward on the storage lid to open the compartment and gain access to this power outlet. In addition to the front power outlet, there is also a power outlet located in the storage area of the c...

  • Page 281

    Note: the rear power outlet can be switched to “bat- tery” powered all the time by switching the power outlet right rear quarter panel fuse in the fuse panel. Rear power outlet power outlet right rear quarter panel fuse 3 understanding the features of your vehicle 279.

  • Page 282

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 283

    Caution! (continued) • accessories that draw higher power (i.E., coolers, vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly. Only use these intermit- tently and with greater caution. • after the use of high power draw accessories, or long periods of the vehicle not being st...

  • Page 284

    May have to be reset manually. To reset the inverter manually press the power inverter button off and on. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. The power inverter switch is located on the switch bank below the climate con- trols....

  • Page 285

    There are two cupholders for the rear seat passengers located in the fold-down center armrest. Front cupholders rear cupholders 3 understanding the features of your vehicle 283.

  • Page 286

    Storage glove compartment the glove compartment is located on the right side of the instrument panel. To open the glove compartment, pull outward on the latch and lower the glove box door. Glove compartment opened glove compartment 284 understanding the features of your vehicle.

  • Page 287

    Door storage large storage areas are built into the door panels for easy access. Center console the center console contains both an upper and a lower storage area. Door panel storage storage compartment 3 understanding the features of your vehicle 285.

  • Page 288

    To open the upper storage compartment, pull upward on the small latch located on the lid. Lift upward on the larger of the latches to access the lower storage compartment. Storage compartment latches lower storage compartment 286 understanding the features of your vehicle.

  • Page 289

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injur...

  • Page 290

    To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Cargo storage bins there are four removable storage bins located in the rear cargo area. There are two storage bins located on either side of the cargo area. Two additional storage bins are l...

  • Page 291

    Tether strap lower storage bins 3 understanding the features of your vehicle 289.

  • Page 292

    Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the...

  • Page 293

    Warning! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. D...

  • Page 294

    Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. • cargo tie-down hooks are not safe anchors for a child seat t...

  • Page 295

    Rear window features rear window wiper/washer the rear wiper/washer controls are located on the mul- tifunction lever on the left side of the steering column. The rear wiper/washer is operated by rotating a switch, located at the middle of the lever. Rotate the center portion of the lever upward to ...

  • Page 296

    If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “park” position. If the flipper glass is open, the rear window wiper/ washer functionality is interrupted and the wiper stops at that “park” position. When the flipper glass is closed, the rear...

  • Page 297

    Roof luggage rack — if equipped the crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Note: if not equipped with crossbars, your authorized ...

  • Page 298

    Caution! • to prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without the crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other ...

  • Page 299: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .301 䡵 instrument cluster — premium . . . . . . .302 䡵 instrument cluster descriptions . . . . .303 䡵 electronic vehicle information center (evic) . . . . . . . . . . . . . . . . . . . . . . .313 ▫ electronic ...

  • Page 300

    ▫ keyless enter-n-go™ display — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .335 ▫ compass / temperature display . . . . . . . . . .336 ▫ customer-programmable features (system setup) . . . . . . . . . . . . . . . . . . . . . . .338 䡵 uconnect® 730n/430/430n cd/dvd/hdd/ nav — if equi...

  • Page 301

    䡵 ipod®/usb/mp3 control — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .373 ▫ connecting the ipod® or external usb device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .373 ▫ using this feature. . . . . . . . . . . . . . . . . . . . .374 ▫ controlling the ipod® or external u...

  • Page 302

    ▫ unwired® stereo headphone lifetime limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . .397 ▫ system information . . . . . . . . . . . . . . . . . . . .398 䡵 steering wheel audio controls — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .415 ▫ radio operation . . ...

  • Page 303

    Instrument panel features 1 — air outlet 6 — lower switch bank 11 — hood release 2 — instrument cluster 7 — hazard switch 12 — fuel door release 3 — radio 8 — storage bin 13 — headlight switch 4 — glove compartment 9 — esc button 14 — dimmer control 5 — climate controls 10 — ignition switch 4 unders...

  • Page 304

    Instrument cluster — premium 302 understanding your instrument panel.

  • Page 305

    Instrument cluster descriptions 1. Tachometer indicates the engine speed in revolutions per minute (rpm x 1000). 2. Air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to the on/run position. If the light is either not on d...

  • Page 306

    Caution! Prolonged driving with the mil on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warning! A malfunctioning catalytic ...

  • Page 307

    Each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. The esc system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when esc becomes inactive following the maneuver that caused the esc activation. 5....

  • Page 308

    10. Electronic vehicle information center (evic) display/odometer display the odometer display shows the total distance the ve- hicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle ha...

  • Page 309

    As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and c...

  • Page 310

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 311

    If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the brake booster has been detected by the anti-lock brake system (abs) / el...

  • Page 312

    Operation of the brake warning light can be checked by turning the ignition switch from the off position to the on/run position. The light should illuminate for ap- proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light ...

  • Page 313

    For further information on four-wheel drive operation and proper use, refer to “four-wheel drive operation — if equipped” in “starting and operating”. 17. Speedometer indicates vehicle speed. 18. Fuel door reminder the fuel pump symbol points to the side of the vehicle where the fuel door is located...

  • Page 314

    23. Electronic stability control (esc) off indicator light — if equipped this light indicates the electronic stability con- trol (esc) is off. 24. Vehicle security light this light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slowe...

  • Page 315

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “maintaining your vehicle”. Follow the warnings unde...

  • Page 316

    • trip info • terrain: (if equipped) • tire psi: (if equipped) • vehicle info • messages • units: setting • system setup • turn menu off the system allows the driver to select information by pressing the following buttons mounted on the steering wheel: evic steering wheel buttons 314 understanding y...

  • Page 317

    Up button press and release the up button to scroll up- ward through the main menus (fuel economy, vehicle info, tire psi, cruise, messages, units, system setup, vehicle speed, trip info, turn menu off and sub-menus. Down button press and release the down button to scroll downward through the main m...

  • Page 318

    Messages that consist of approximately 60 possible warn- ing or information messages. These pop up messages fall into several categories: he reconfigurable telltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left. • five se...

  • Page 319

    When the appropriate conditions exist, the evic displays the following messages: • vehicle not in park • key left vehicle • key not detected • service tpm system (refer to “tire pressure monitor- ing system” in “starting and operating”) • premium tpm system graphic display • service keyless system (...

  • Page 320

    • adaptive cruise off — when the adaptive cruise control (acc) system is turned off. Refer to “adaptive cruise control (acc)” in “understanding the fea- tures of your vehicle” (if equipped). • acc ready — when the acc system is activated. Refer to “adaptive cruise control (acc)” in “under- standing ...

  • Page 321

    • clean radar sensor in the front of vehicle — if the acc system deactivates due to performance limiting conditions. Refer to “adaptive cruise control (acc)” in “understanding the features of your vehicle” (if equipped). • acc/fcw unavailable vehicle system error — if the acc system turns off due to...

  • Page 322

    • remote start aborted — fuel low • remote start disabled — start vehicle to reset • remote start active — insert key and turn to run • remote start active — push start button • memory 1 profile set • memory 2 profile set • memory system unavailable — not in park • memory system unavailable — seatbe...

  • Page 323

    • to tow vehicle safely, read neutral shift procedure in owners manual • for 4x4 low slow below 5 mph or 8 kph put trans in n press 4 low • for 4x4 high slow below 5 mph or 8 kph put trans in n press 4 low • terrain system settings not available • raising vehicle ride height (with icon) • lowering v...

  • Page 324

    • immediate air suspension service/repair required — this is displayed when a fault has occurred in the system which results in a complete system shutdown. The system will be non operational at that point. • reduce speed to maintain selected ride height — this message is displayed in advance warning...

  • Page 325

    • electronic speed control on this light will turn on when the electronic speed control is on. For further information, refer to “electronic speed control” in “under- standing the features of your vehicle.” • electronic speed control set this light will turn on when the electronic speed control is s...

  • Page 326

    Longer exists. Once driving conditions are safe, then pull over and let vehicle idle. After 5 minutes, the system will cool and return to normal operation. Refer to “power steering” in “starting and operating” for further information. Note: • even if power steering assistance is no longer opera- tio...

  • Page 327

    • air suspension down the air suspension down telltale will illumi- nate when the air suspension is in use. For further information, refer to “starting and operating”. • low fuel light when the fuel level reaches approximately 3.0 gal (11.0 l) this light will turn on, and remain on until fuel is add...

  • Page 328

    • liftgate ajar this light will turn on to indicate that liftgate may be ajar. • liftgate flipper glass ajar this light will turn on to indicate that liftgate flipper glass may be ajar. • oil pressure warning light this telltale indicates low engine oil pressure. If the light turns on while driving,...

  • Page 329

    If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the park position. The light should turn off. If the light remains lit with the engine running, your vehicle will usually be d...

  • Page 330

    Light comes on, stop the vehicle and run the engine at idle or faster, with the transmission in neutral until the light goes off. Caution! Continuous driving with the transmission tempera- ture warning light illuminated will eventually cause severe transmission damage or transmission failure. Warnin...

  • Page 331

    Vehicles equipped with keyless enter-n-go™ 1. Without pressing the brake pedal, push the engine start/stop button and cycle the ignition to the on/ run position (do not start the engine). 2. Fully depress the accelerator pedal, slowly, three times within 10 seconds. 3. Without pressing the brake ped...

  • Page 332

    The trip functions mode displays the following informa- tion: average fuel economy / fuel saver mode — if equipped shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “reset” or show dashes for two seconds. Then, the history information will be ...

  • Page 333

    Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. Dte cannot be reset through the select b...

  • Page 334

    Other feature is in the evic main display, the cruise status will be displayed in place of the evic odometer line. Press and release the back button to return to the main menu. Vehicle speed press and release the up or down button until “vehicle speed” displays highlighted in the evic and press the ...

  • Page 335

    Elapsed time shows the total elapsed time of travel since the last reset when the ignition switch is in the acc position. Elapsed time will increment when the ignition switch is in the on or start position. To reset the display press and release the up or down button until “vehicle info” displays in...

  • Page 336

    • trans temperature displays the actual transmission temperature. • engine hours displays the number of hours of engine operation. Tire psi press and release the up or down button until “tire psi” displays highlighted in the evic and press the select button. Press and release the up/down but- tons u...

  • Page 337

    Note: • tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kpa) during normal driving conditions. Refer to “tires- general information/tire inflation pressures” in “start- ing and operating” for additional information. • your syste...

  • Page 338

    Note: under certain conditions, the display may be superseded by another display of higher priority. But when the ignition switch position is changed, the display always re-appears. Compass / temperature display the compass readings indicate the direction the vehicle is facing. The evic will display...

  • Page 339

    Note: keep magnetic materials away from the top of the instrument panel, such as ipod’s, mobile phones, laptops and radar detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. 1. Turn the ignition switch on. 2. ...

  • Page 340

    Note: for the most accurate compass performance, the compass variance must be set before performing the manual compass calibration. The variance should be set for the zone where the vehicle is driven, per the zone map. For further information, refer to “compass vari- ance.” 1. Turn on the ignition s...

  • Page 341

    Select language when in this display you may select one of five lan- guages for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the up or down button while in this display and scroll through the language choices. Press the select button to select...

  • Page 342

    When unlock all doors on 1st press is selected, all of the doors will unlock on the first press of the rke transmitter unlock button. To make your selection, scroll up or down until the preferred setting is high- lighted, then press and release the select button until a check-mark appears next to th...

  • Page 343

    Seat features will automatically turn on when tempera- tures are below 40° f (4.4° c). When temperatures are above 80° f (26.7° c) the driver vented seat will turn on. These features will stay on through the duration of remote start or until the key is turned to run. To make your selection, press an...

  • Page 344

    Headlamp off delay when this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To make your selection, scroll up or down until the preferred setting is highlighted, then press and release the select button until a check...

  • Page 345

    Note: the seat will return to the memorized seat location (if recall memory with remote key unlock is set to on) when the rke transmitter is used to unlock the door. Refer to “driver memory seat” in “understanding the features of your vehicle” for further information. Tilt mirror in reverse when thi...

  • Page 346

    Display fuel saver — if equipped the “eco” message is located in the compass/ temperature display; this message can be turned on or off. To make your selection, press and release the select button until a check-mark appears next to the setting, showing that the setting has been selected. Keyless ent...

  • Page 347

    Hill start assist (hsa) — if equipped when this feature is selected, the hsa system is active. Refer to “electronic brake control system” in “starting and operating” for system function and operating infor- mation. To make your selection, press and release the select button until a check-mark appear...

  • Page 348

    Dynamic driving select the near setting. This warns you of a possible collision with the vehicle in front of you when you are much closer. This allows for a more dynamic driving experience. To change fcw status press and release the select button until a check-mark ap- pears next to the feature show...

  • Page 349

    Calibrate compass refer to “compass display” for more information. Compass variance refer to “compass display” for more information. Uconnect® 730n/430/430n cd/dvd/hdd/nav — if equipped refer to your uconnect® 730n, 430 or 430n user’s manual for detailed operating instructions. Operating instruction...

  • Page 350

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 351

    3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll con- trol knob to save time change. 5. To exit, press any button/knob, or wait...

  • Page 352

    Push the rotary tune/scroll control knob a fifth time and fade will display. Turn the tune/scroll control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button pres...

  • Page 353

    Disc button pressing the disc button will allow you to switch from am/fm modes to disc modes. Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordab...

  • Page 354

    Caution! (continued) • the uconnect® 130 is a single cd player. Do not attempt to insert a second cd if one is already loaded. • dual-media disc types (one side is a dvd, the other side is a cd) should not be used, and they can cause damage to the player. Eject button - ejecting a cd press the eject...

  • Page 355

    Rw/ff press and hold the ff (fast forward) button and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (reverse) button works in a similar manner. Am/fm button press the button to select either am or fm mode. Set/rnd button (random play but...

  • Page 356

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 357

    Use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rate. Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56,...

  • Page 358

    Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the user to plug in a portable device, such as an mp3 player, or ipod®, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the disc/aux butt...

  • Page 359

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 de- grees) in either direction, without stopping. Turning th...

  • Page 360

    Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the mi...

  • Page 361

    Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control...

  • Page 362

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or undefined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news n...

  • Page 363

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 364

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored i...

  • Page 365

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 366

    The current selection. Pressing and holding the seek button will allow faster scrolling through the tracks in cd and mp3 modes. Time button press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff press and hold ff (fast forward) and the ...

  • Page 367

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 368

    Discs created with an option such as ⬙keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for cd audio or mp3 playback may result in longer disc loading times. Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 file...

  • Page 369

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 370

    Press and hold the info button again for three seconds to return to ⬙elapsed time⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or ipod® and utilize the vehicle’s audio system...

  • Page 371

    System activation sirius satellite radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, includ...

  • Page 372

    Decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehi...

  • Page 373

    Info button pressing the info button will cycle the display informa- tion between artist, song title, and composer (if avail- able). Also, pressing and holding the info button for an additional three seconds will make the radio display the song title all of the time (press and hold again to return t...

  • Page 374

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set button – to set the pushbutton memory when...

  • Page 375

    Ipod®/usb/mp3 control — if equipped this feature allows an ipod® or external usb device to be plugged into the usb port, located in the center console or glove compartment. Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support ...

  • Page 376

    Note: the center console will have a position where the ipod® or consumer electronic audio device cable can be routed through without damaging the cable when clos- ing the lid. A factory cut out space for the cable to be routed may be located in the base of the center console on either the front or ...

  • Page 377

    Controlling the ipod® or external usb device using radio buttons to get into the ipod®/usb/mp3 control mode and access a connected audio device, either press the “aux” button on the radio faceplate or press the vr button and say ⬙usb⬙ or ⬙switch to usb⬙. Once in the ipod®/usb/ mp3 control mode, audi...

  • Page 378

    • while a track is playing, press the info button to see the associated metadata (artist, track title, album, etc.) for that track. Pressing the info button again jumps to the next screen of data for that track. Once all screens have been viewed, the last info button press will go back to the play m...

  • Page 379

    • turning it clockwise (forward) and counterclockwise (backward) scrolls through the lists, displaying the track detail on the radio display. Once the track to be played is highlighted on the radio display, press the tune control knob to select and start playing the track. Turning the tune control k...

  • Page 380

    • music type button: the music type button is another shortcut button to the genre listing on your audio device. Caution! • leaving the ipod® or external usb device (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the devi...

  • Page 381

    Selecting different audio device 1. Press phone button to begin. 2. After the ⬙ready⬙ prompt and the following beep, say ⬙setup⬙, then ⬙select audio devices⬙. 3. Say the name of the audio device or ask the uconnect® phone system to list audio devices. Next track use the seek up button, or press the ...

  • Page 382

    Uconnect® multimedia — video entertainment system (ves)™ — if equipped getting started • screen located in the overhead console: unfold the overhead lcd screen by pushing the button in the center of the overhead console behind the screen. • with the ignition switch in the on or acc position, turn th...

  • Page 383

    Or press the load button then corresponding number (1–6) where the dvd is to be loaded (non-touch-screen). 2. Insert the dvd with the label facing up. The radio automatically selects the appropriate mode after the disc is recognized and displays the menu screen or starts playing the first track. 3. ...

  • Page 384

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list appears on the right side of the screen, touch the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 so...

  • Page 385

    Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key and then the view video soft-key. • viewing a dvd on the touch-screen radio screen is not available in all states/provinces, and the vehicle must be stopped, and the shift leve...

  • Page 386

    Play video games connect the video game console to the auxiliary rca input jacks located on the back of the center console. When connecting an external source to the aux input, be sure to follow the standard color coding for the ves™ jacks: note: certain high-end video games, such as playsta- tion3 ...

  • Page 387

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. Select ves aux1 mode on the ves screen rear ...

  • Page 388

    3. Touch the 1 soft-key and then touch aux 1 in the ves column. To exit press the back arrow soft-key at the top of the screen. Listen to an audio source on channel 2 while a video is playing on channel 1 ensure the remote control and headphone switch is on channel 2. Using the remote control 1. Pre...

  • Page 389

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. Select fm mode on the ves screen rear ves so...

  • Page 390

    3. To listen to an audio source on channel 2 while a video is playing on channel 1, touch the 2 soft-key and choose an audio source. To exit touch the back arrow soft-key at the top left of the left screen. Important notes for single video screen system • ves™ is able to transmit two channels of ste...

  • Page 391

    Play a dvd using the touch-screen radio 1. Press the open/close or load hard-key on the radio faceplate (touch-screen). 2. Insert the dvd with the label facing up. The radio automatically selects the appropriate mode after the disc is recognized and displays the menu screen or starts playing the fir...

  • Page 392

    Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, press the hide list soft-key to display the rear ves controls screen. 3. Touch the 1 or 2 soft-key and then the di...

  • Page 393

    Ves remote control – if equipped controls and indicators 1. Power – turns the screen and wireless headphone transmitter for the selected channel on or off. To hear audio while the screen is closed, press the power button to turn the headphone transmitter on. 2. Channel selector indicators – when a b...

  • Page 394

    5. 䉴䉴 – in radio modes, press to seek the next tunable station. In disc modes, press and hold to fast forward through the current audio track or video chapter. In satellite video mode, press to advance to the next channel. In menu modes use to navigate in the menu. 6. 䉲 / prev – in radio modes, pres...

  • Page 395

    15. Setup – when in a video mode, press the setup button to access the display settings (see the display settings section) or the dvd setup menu. When a disc is loaded in the dvd player (if equipped) and the ves™ mode is selected and the disc is stopped, press the setup button to access the dvd setu...

  • Page 396

    Storage area, insert one long edge of the remote into the two retaining clips first, and then rotate the remote back up into the other two retaining clips until it snaps back into position. Locking the remote control all remote control functionality can be disabled as a parental control feature. • t...

  • Page 397

    • replace the batteries, making sure to orient them according to the polarity diagram shown. • replace the battery compartment cover. Headphones operation the headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some head...

  • Page 398

    Controls the headphone power indicator and controls are located on the right ear cup. Note: the rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video sys...

  • Page 399

    Replacing the headphone batteries each set of headphones requires two aaa batteries for operation. To replace the batteries: • locate the battery compartment on the left ear cup of the headphones, and then slide the battery cover downward. • replace the batteries, making sure to orient them accordin...

  • Page 400

    Nature whatsoever. Some states and jurisdictions may not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights, which vary from jurisdiction to jurisdiction...

  • Page 401

    If the radio functions (fm, am, or sat) are in the shared mode with the ves™, only the radio is able to control the radio functions. In this case, ves™ can share the radio mode, but not change stations until the radio mode is changed to a mode that is different from the ves™ selected radio mode. Whe...

  • Page 402

    Information mode display when information mode is active, the current mode setting for both audio channels is displayed. In addition to the items called out by number, the remaining infor- mation displays the current status of the source (such as station frequency, name, preset or track number, song...

  • Page 403

    5. Channel 2 shared status – when the icon is displayed, the audio for channel 2 is also shared with the radio and playing through the cabin speakers. 6. Channel 2 audio only/mute – audio: only in a single screen system: the audio only icon is displayed on channel 2 when channel 1 is in a video mode...

  • Page 404

    Mode selection menu the first press of the mode button causes the mode selection menu to appear on screen. The current mode is always the default selection. The mode can be changed for either channel/screen 1 or channel/screen 2 using the remote control. Use the remote control’s navigation buttons (...

  • Page 405

    Numeric keypad menu when the display for either channel 1 or channel 2 shows direct tune, pressing the remote control’s enter button activates a numeric keypad menu. This screen makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Pres...

  • Page 406

    Navigation buttons ( 䉱, 䉲) to find the desired station, press the remote control’s enter button to tune to that station. To jump through the list more quickly, navigate to the page up and page down icons on the screen. Disc menu when listening to a cd audio or cd data disc, pressing the remote contr...

  • Page 407

    When watching a video source (dvd video with the disc in play mode, aux video, sirius backseat tv™, etc.), pressing the remote control’s setup button activates the display settings menu. These settings control the appear- ance of the video on the screen. The factory default settings are already set ...

  • Page 408

    The remote control’s power button to turn audio on. If audio is still not heard, check that fully charged batteries are installed in the headphones. Disc formats the ves™ dvd player is capable of playing the follow- ing types of discs (12 mm or 8 mm diameter): • dvd-video discs (mpeg-2 video compres...

  • Page 409

    Dvd audio support when a dvd-audio disc is inserted in the ves™ dvd player, the dvd-audio title on the disc is played by default (most dvd-audio discs also have a video title, but the video title is ignored). All multi-channel program material is automatically mixed down to two channels, which may r...

  • Page 410

    • mixed media recordable dvd formats will only play the video_ts portion of the disc. If you are still having trouble writing a disc that is playable in the ves™ dvd player, check with the disc recording software publisher for more information about burning playable discs. The recommended method for...

  • Page 411

    • if you are creating your own files, the recommended fixed bit rate for mp3 files is between 96 and 192kbps and the recommended fixed bit rate for wma files is between 64 and 192kbps. Variable bit rates are also supported. For both formats, the recommended sample rate is either 44.1khz or 48khz. • ...

  • Page 412

    Display other language setup all of the language settings have a special ⬙other⬙ setting to accommodate languages other than japanese or eng- lish. These languages are selected using a special four- digit code. To enter a new language code, activate the dvd setup menu and follow these additional ins...

  • Page 413

    • when the entire four-digit code is entered, press the remote control’s enter button. If the language code is not valid, the numbers all change back to ⬙夡⬙. If the digits are visible after this step, then the language code is valid. Here is an abbreviated list of language codes. For more language c...

  • Page 414

    The default rating is level 8 (play all discs without a password) and the default password is 0000. To set the password, activate the dvd setup menu and follow these additional instructions: • using the remote control left and right cursor but- tons, select the rating tab. • highlight ⬙change passwo...

  • Page 415

    • after the four-digit password is entered, press the remote control’s enter button. If the password is correct, the set password screen is displayed. • using the remote control’s up and down cursor buttons to set the value for the current digit and the remote control’s right cursor button to select...

  • Page 416

    To set the rating, activate the dvd setup menu and follow these additional instructions: • using the remote control’s left and right cursor buttons, select the rating tab. • highlight ⬙change rating⬙, and then press the remote control’s enter button. • enter the current password. Select a digit, use...

  • Page 417

    General information this system complies with part 15 of the fcc operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired op- eration. Steering wheel ...

  • Page 418

    Pressing the center button will make the radio switch between the various modes available (am/fm/sat/ cd/aux/ves, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following...

  • Page 419

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 420

    Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. Dual-zone manual heating and air conditioning the dual-zone manual climate controls allow both driver and front passenger seat occupants to select indi- vidual comfort settings. The ...

  • Page 421

    Temperature controls • driver temperature control rotate this control to regulate the tem- perature of the air inside the passenger compartment for the left front seat occu- pant. Rotating the dial left into the blue area of the scale indicates cooler tem- peratures, while rotating right into the re...

  • Page 422

    Note: the center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear. Bi-level air is directed through the panel and floor outlets. Note: for all settings, except full cold or full hot, there is a difference in temperature b...

  • Page 423

    • the air conditioning compressor operates in mix, defrost, or a blend of these modes, even if the air conditioning (a/c) button is not pressed. This dehu- midifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary. Recirculation control pressing the re...

  • Page 424

    Air conditioning control press this button to engage the air con- ditioning. A light will illuminate when the air conditioning system is engaged. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures...

  • Page 425

    • the system provides set-and-forget operation for op- timum comfort and convenience. • the system can also be controlled manually, if desired. The atc system automatically maintains the interior comfort level desired by the driver and passenger. 1. A/c button press and release to change the current...

  • Page 426

    5. Blower control display this display shows the current blower speed selection. 6. Right front seat occupant temperature display this display shows the temperature setting for the right front seat occupant. 7. Front defrost button press and release to change the current setting, the indicator illum...

  • Page 427

    12. Climate control off button press and release this button to turn the climate control off. If the control is off, any button will turn the control on. 13. Mode control button press and release to select between modes (panel, bi- level, floor, mix). Performing this function will cause the atc to s...

  • Page 428

    Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to provide comfort as quickly as possible. • the temperature can be displayed in u.S. Or metric units by selecting the us/m customer-programmabl...

  • Page 429

    The operator can also select the direction of the airflow by selecting one of the following positions. Panel mode air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets...

  • Page 430

    Note: while operating in the other modes, the system will not automatically sense the presence of fog, mist or ice on the windshield. Defrost mode must be manually selected to clear the windshield and side glass. Air conditioning (a/c) the air conditioning (a/c) button allows the operator to manuall...

  • Page 431

    Note: in cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation mode is not allowed in the defrost modes to improve window clearing operation. Recirculation will be dis- abled automatically if defrost is selected. Operating tips window fogging windows will fo...

  • Page 432

    Your air conditioning system is also equipped with an automatic recirculation system. When the system senses a heavy load or high heat conditions, it may use partial recirculation a/c mode to provide additional comfort. Winter operation when operating the system during the winter months, make sure t...

  • Page 433

    Operating tips chart 4 understanding your instrument panel 431.

  • Page 435: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .439 ▫ automatic transmission . . . . . . . . . . . . . . . .439 ▫ keyless enter-n-go™ . . . . . . . . . . . . . . . . . .440 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .441 ▫ extreme cold weather (...

  • Page 436

    䡵 four-wheel drive operation . . . . . . . . .467 ▫ quadra-trac i® operating instructions/ precautions – if equipped . . . . . . . . . . . . . . .467 ▫ quadra-trac ii® operating instructions/ precautions – if equipped . . . . . . . . . . . . . . .468 ▫ shift positions . . . . . . . . . . . . . . . ....

  • Page 437

    䡵 power steering . . . . . . . . . . . . . . . . . . . . .487 ▫ 3.6l engine . . . . . . . . . . . . . . . . . . . . . . . . . .487 ▫ 5.7l engine . . . . . . . . . . . . . . . . . . . . . . . . . .489 ▫ power steering fluid check . . . . . . . . . . . . . .490 䡵 fuel saver technology 5.7l engine only...

  • Page 438

    䡵 tires — general information. . . . . . . . .518 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .518 ▫ tire inflation pressures . . . . . . . . . . . . . . . . .519 ▫ tire pressures for high speed operation . . . .521 ▫ radial ply tires . . . . . . . . . . . . . . . . . . . . . .521 ...

  • Page 439

    ▫ reformulated gasoline . . . . . . . . . . . . . . . . .542 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . .542 ▫ e-85 usage in non-flex fuel vehicles . . . . . . .542 ▫ mmt in gasoline . . . . . . . . . . . . . . . . . . . . .543 ▫ materials added to fuel . . . . . . . . . . . . . . . .544 ...

  • Page 440

    ▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . .562 ▫ trailer and tongue weight . . . . . . . . . . . . . .562 ▫ towing requirements . . . . . . . . . . . . . . . . . .563 ▫ towing tips . . . . . . . . . . . . . . . . . . . . . . . . .569 䡵 snow plow . . . . . . . . . . . ...

  • Page 441

    Starting procedures before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your ve...

  • Page 442

    Caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • do not shift from reverse, park, or neutral into any forward gear when the engine is above idle speed. • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse...

  • Page 443

    Installing and removing the engine start/stop button installing the button 1. Remove the key fob from the ignition switch. 2. Insert the engine start/stop button into the ignition switch with the lettering facing up and read- able. 3. Press firmly on the center of the button to secure it into positi...

  • Page 444

    To turn off the engine using engine start/stop button 1. Place the shift lever in park, then press and release the engine start/stop button. 2. The ignition switch will return to the off position. 3. If the shift lever is not in park, the engine start/ stop button must be held for two seconds and ve...

  • Page 445

    • press the engine start/stop button a second time to change the ignition switch to the run position (evic displays “ignition mode run”), • press the engine start/stop button a third time to return the ignition switch to the off position (evic displays “ignition mode off”). Extreme cold weather (bel...

  • Page 446

    Clearing a flooded engine (using engine start/stop button) if the engine fails to start after you have followed the “normal starting” or “extreme cold weather ⬙ proce- dures, it may be flooded. To clear any excess fuel: 1. Press and hold the brake pedal. 2. Press the accelerator pedal all the way to...

  • Page 447

    Caution! To prevent damage to the starter, wait 10 to 15 seconds before trying again. After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold ...

  • Page 448

    Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine is at idle spee...

  • Page 449

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 450

    Note: if a malfunction occurs, the system will trap the key fob in the ignition switch to warn you that this safety feature is inoperable. The engine can be started and stopped but the key fob cannot be removed until you obtain service. Brake/transmission shift interlock system this vehicle is equip...

  • Page 451

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when moving the shift lever between these gears. The transmission shift lever has only park, reverse, neutral, and drive shift positions. Manual do...

  • Page 452

    Note: • after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. • if there is a need to restart the engine, be sure to cycle the ignition to the off position before restarting. Transmission gear eng...

  • Page 453

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 454

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 455

    Reverse this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift ...

  • Page 456

    Drive this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through underdrive first, second, and third gears, direct fourth gear and overdrive fifth gear. The drive positio...

  • Page 457

    4. Wait approximately 10 seconds. 5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest po...

  • Page 458

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Screen display 1 2 3 4 d actual gear(s) allowed 1 1-2 1-3 1-4 1-5 note: to select the proper gear position for max...

  • Page 459

    The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilomete...

  • Page 460

    Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use...

  • Page 461

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 462

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 463

    Reverse this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift ...

  • Page 464

    Drive this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through underdrive first and sec- ond gears, direct third gear and overdrive fourth and fifth gears. The drive po...

  • Page 465

    (when stopped in heavy traffic) can help to reduce this excess heat generation. During cold temperatures, transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed. This feature im- proves warm up time of the engine and transmission to achieve m...

  • Page 466

    6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic...

  • Page 467

    The instrument cluster display will show the requested top gear limit, however the transmission will not down- shift to the requested gear if doing so would overspeed the engine. The transmission will downshift once the vehicle speed has slowed sufficiently. To exit ers mode, simply press and hold t...

  • Page 468

    • vehicle speed is sufficiently high, • the driver is not heavily pressing the accelerator, and • the tow/haul switch has not been activated. When to use tow/haul mode when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the t...

  • Page 469

    Torque converter clutch a feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly different feeling or response during normal operation in ...

  • Page 470

    Abs and traction control, provides resistance to any wheel that is slipping to allow additional torque transfer to wheels with traction. Note: the quadra-trac i® system is not appropriate for conditions where 4wd low range is recommended. Refer to “off-road driving tips” in “starting and oper- ating...

  • Page 471

    Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit. Warning! You or others could be injured if you leave the vehicle unattended with the transfer case in the neutral (n) position without fi...

  • Page 472

    4wd low this range is for low speed four-wheel drive. It locks the front and rear driveshafts together and forces the front and rear wheels to rotate at the same speed. It provides additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). N...

  • Page 473

    Note: if shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “for 4x4 low slow below 3 mph or 5 kph put trans in n press 4 low” message will flash from the electronic vehicle information center (evic). Refer to “electronic vehicle information ...

  • Page 474

    Neutral shift procedure 1. Turn the ignition switch to the on position, engine off. 2. Vehicle stopped, with foot on brake. 3. Place the transmission into neutral. 4. Hold down the neutral “pin” switch (with a pen, etc.) for four seconds until the led light by the switch starts to blink indicating s...

  • Page 475

    Quadra-drive® ii system – if equipped the optional quadra-drive® ii system features two torque transfer couplings. The couplings include an electronic limited-slip differential (elsd) rear axle and the quadra-trac ii® transfer case. The optional elsd axle is fully automatic and requires no driver in...

  • Page 476

    Selec-terrain™ consists of the following positions: • sport – dry weather, on-road calibration. Only avail- able in 4wd high range. Performance based tuning that provides a rear wheel drive feel but with im- proved handling and acceleration over a two-wheel drive vehicle. The electronic stability co...

  • Page 477

    • rock – off-road calibration only available in 4wd low range. The vehicle is raised (if equipped with air suspension) for improved ground clearance. Traction based tuning with improved steer-ability for use on high traction off-road surfaces. Activate the hill de- scent control for steep downhill c...

  • Page 478

    Quadra-lift™ — if equipped description the quadra-lift™ air suspension system provides full time load leveling capability along with the benefit of being able to adjust vehicle height by the push of a button. Selec-terrain™ switch 1 — up button 2 — down button 3 — park mode indicator lamp 4 — normal...

  • Page 479

    • normal ride height (nrh) – this is the standard position of the suspension and is meant for normal driving. • off-road 1 (or1) (raises the vehicle approximately 1.3 in (33 mm) – this is the primary position for all off-road driving until or2 is needed. A smoother and more comfortable ride will res...

  • Page 480

    Selec-terrain™ knob is turned to the “sport” posi- tion. Turning the selec-terrain™ knob to the “auto” position will return the system to normal operation. • park mode (lowers the vehicle approximately 1.5 in (38 mm) – this position lowers the vehicle for easier passenger entry and exit as well as l...

  • Page 481

    After the engine is turned off, it may be noticed that the air suspension system operates briefly, this is normal. The system is correcting the position of the vehicle to ensure a proper appearance. To assist with changing a spare tire, the quadra-lift™ air suspension system has a feature which allo...

  • Page 482

    Operation the indicator lamps 3 through 6 will illuminate to show the current position of the vehicle. Flashing indicator lamps will show a position which the system is working to achieve. When raising, if multiple indicator lamps are flashing on the “up” button, the highest flashing indica- tor lam...

  • Page 483

    • normal ride height (nrh) – indicator lamp 4 will be illuminated when the vehicle is in this position. • park mode – indicator lamp 3 will be illuminated when the vehicle is in park mode. If park mode is requested while vehicle speed is between 15 mph (24 km/h) and 25 mph (40 km/h), indicator lamp ...

  • Page 484

    Off-road driving tips note: prior to off-road driving, remove the front air dam to prevent damage. The front air dam is attached to the lower front fascia with seven quarter turn fasteners and can be removed by hand. Front air dam 1 — front bumper 2 — front air dam fasteners 482 starting and operati...

  • Page 485

    Quadra-lift™ – if equipped when off-roading, it is recommended that the lowest useable vehicle height that will clear the current obstacle or terrain be selected. The vehicle height should then be raised as required by the changes in terrain. The selec-terrain™ switch will automatically change the v...

  • Page 486

    Note: your vehicle is capable of water fording in up to 20 inches (51 cm) of water, while crossing small rivers or streams. To maintain optimal performance of your vehi- cle’s heating and ventilation system it is recommended to switch the system into recirculation mode during water fording. Caution!...

  • Page 487

    Maintenance after driving through deep water, inspect your vehicle fluids and lubricants (engine oil, transmission oil, axle, transfer case) to assure the fluids have not been contami- nated. Contaminated fluid (milky, foamy in appearance) should be flushed/changed as soon as possible to pre- vent c...

  • Page 488

    Warning! If the engine stalls, you lose forward motion, or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle. Always back care- fully straight down a hill in reverse gear. Never back down a hill in neutral using o...

  • Page 489

    • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiator for mud and debris and clean as required. • check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steerin...

  • Page 490

    The system will vary its assist to provide light efforts while parking and good feel while driving. If the electro- hydraulic power steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability. Caution! Extreme...

  • Page 491

    Note: • even if power steering assistance is no longer opera- tional, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. • if the condition persists, see your a...

  • Page 492

    Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature an...

  • Page 493

    If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fuel saver technology 5.7l engine only – if equipped this feature of...

  • Page 494

    When the parking brake is applied with the ignition switch in the on position, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the transmis- sion is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, ...

  • Page 495

    Warning! (continued) • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others ...

  • Page 496

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes the anti-lock brake system (abs), traction control system (tcs), brake assist system (bas), electronic roll mitigation (erm), and electronic stability control (esc). All five of th...

  • Page 497

    A feature of the tcs system, brake limited differential (bld), functions similar to a limited-slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow mo...

  • Page 498

    Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicle’s speed are sufficient to potentially cause wheel li...

  • Page 499

    Electronic stability control (esc) this system enhances directional control and stability of the vehicle under various driving conditions. Esc cor- rects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteer or unders...

  • Page 500

    Warning! (continued) hydroplaning. Esc also cannot prevent collisions resulting from loss of vehicle control due to inappro- priate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent collisions. The capabilities of an esc equipped vehicle must never be exploited...

  • Page 501

    Features of esc function normally. This mode is intended to be used if the vehicle is in deep snow, sand, or gravel conditions and more wheel spin than esc would nor- mally allow is required to gain traction. To turn esc on again, momentarily press the “esc off” switch. This will restore the normal ...

  • Page 502

    Trailer sway control (tsc) tsc uses sensors in the vehicle to recognize an exces- sively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appro- priate wheel(s) to counteract the sway of the trailer. Tsc ...

  • Page 503

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 6% (approximate) grade or greater hill. • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphi...

  • Page 504

    Towing with hsa hsa will provide assistance when starting on a grade when pulling a trailer. Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enoug...

  • Page 505

    Ready alert braking – if equipped ready alert braking may reduce the time required to reach full braking during emergency braking situations. It anticipates when an emergency braking situation may occur by monitoring how fast the throttle is released by the driver. When the throttle is released very...

  • Page 506

    Hill descent control (hdc) — four-wheel drive models with mp3023 two-speed transfer case only hdc maintains vehicle speed while descending hills during off-road driving situations and is available in 4wd low range only. To enable hdc, press the hdc switch or put the selec-terrain™ system in “rock” m...

  • Page 507

    The hdc speed may be adjusted by the driver to suit the driving conditions. The speed corresponds to the trans- mission gear selected. Hdc operation can be overridden with brake application to slow the vehicle down below the hdc control speed. Conversely, if more speed is desired during hdc control,...

  • Page 508

    Warning! Hdc is only intended to assist the driver in control- ling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed. Esc activation/malfunction indicator light and esc off indicator light the “esc...

  • Page 509

    Note: • the “esc activation/malfunction indicator light” and the “esc off indicator light” come on momen- tarily each time the ignition switch is turned on. • each time the ignition is turned on, the esc system will be on even if it was turned off previously. • the esc system will make buzzing or cl...

  • Page 510

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 511

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 215 ...

  • Page 512

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 513

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 514

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 515

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire placard location 5 starting and operating 513.

  • Page 516

    Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loa...

  • Page 517

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 518

    5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult th...

  • Page 519

    5 starting and operating 517.

  • Page 520

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 521

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear pat- terns...

  • Page 522

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire infl...

  • Page 523

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 524

    The tire sidewall. Use all season tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Summer or three season tires – if equipped summer tires provide traction in both wet and dry conditions, and are not intended to be driven in snow or on ice. S...

  • Page 525

    Spare tire matching original equipped tire and wheel – if equipped your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for y...

  • Page 526

    Since this tire has limited tread life the original equip- ment tire should be repaired (or replaced) and reinstalled on your vehicle at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically fo...

  • Page 527

    Your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than ...

  • Page 528

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 529

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 530

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 531

    • due to limited clearance, the security chain company (scc) super z6 low profile traction device or equivalent is recommended on p265/60r18 or 265/50r20 tires. Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose c...

  • Page 532

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation ...

  • Page 533

    Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold tire placard pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the...

  • Page 534

    The tpms will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold tire placard pressure. Once the low tire pressure warning has been illuminated, the tire pressure must be increased to the rec...

  • Page 535

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or ...

  • Page 536

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system the tire pressure monitor system (tpms) uses wireless technology with wheel rim-mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each w...

  • Page 537

    The tire pressure monitoring telltale light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. In addition, a “service tpm system” message may be displayed for approximately 5 seconds when a system fault is detected, and a chime will sound. If the ignition swi...

  • Page 538

    Minimum of five seconds, and the tire pressure monitor- ing telltale light will flash on and off for 75 seconds and then remain on solid. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the spare tire, the tpms will update automatically and the tire pre...

  • Page 539

    Tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illuminate in the instrument cluster, and an au- dible chime will be activated, when one or more of the four active road tire pressures are low. In addition, the evic will display a “low tire pressure” me...

  • Page 540

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is “flashing” on the graphic display to the vehicle’s recommended cold tire pressure displayed in the ⬙inflate to xxx⬙ message. The system will automaticall...

  • Page 541

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the ⬙service tpm system⬙ message will not be present, and a pressure value will be displayed i...

  • Page 542

    Vehicle for up to 20 minutes above 15 mph (24 km/h), the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system ⬙ mes- sage for five seconds and then display dashes (- -) in place of the pressure...

  • Page 543

    Fuel requirements 3.6l engine – if equipped this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high-quality unleaded “regular” gaso- line having an octane rating of 87. The use of premium gasoline is not recommended, as it will...

  • Page 544

    Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” reformulated gasolines contain oxygenates and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of ref...

  • Page 545

    If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • operate in a lean mode • obd ii “malfunction indicator light” on • poor engine performance • poor cold start and cold drivability • increased risk for fuel system component corrosion to...

  • Page 546

    Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the f...

  • Page 547

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 548

    Flexible fuel (3.6l engine only) — if equipped e-85 general information the information in this section is for flexible fuel ve- hicles only. These vehicles can be identified by a unique fuel filler door label that states ethanol (e-85) or un- leaded gasoline only. This section only covers those sub...

  • Page 549

    Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap)...

  • Page 550

    When you do switch fuel types it is recommended that: • you do not add less than 5 gallons (19 liters) when refueling • you drive the vehicle immediately after refueling for at least 5 miles (8 km) observing these precautions will avoid possible hard starting and/or significant deterioration in driv...

  • Page 551

    Starting the characteristics of e-85 fuel make it unsuitable for use when ambient temperatures fall below 0°f (-18°c). In the range of 0°f (-18°c) to 32°f (0°c), you may experience an increase in the time it takes for your engine to start, and a deterioration in driveability (sags and/or hesitations...

  • Page 552

    Adding fuel fuel filler cap (gas cap) the gas cap is located behind the locking fuel filler door, on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. 1. Press the fuel filler door release switch (located under the headlamp...

  • Page 553

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indi- cator light (mil)” to illuminate, due to f...

  • Page 554

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel when the engine is running. This is in violation of most state and federal fire regulations and may cause the malfunction indicator light to turn on. • a f...

  • Page 555

    5. Pull the release cable. Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a loose gascap indicator will display in the evic telltale display area. Refer to “electronic vehicle information center (evic)” i...

  • Page 556

    Gross vehicle weight rating (gvwr) the gvwr is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo. The label also specifies maximum capacities of front and rear axle systems (gawr). Total load must be limited so gvwr and front and rear gawr are not ...

  • Page 557

    Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a comm...

  • Page 558

    Trailer towing in this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow t...

  • Page 559

    Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Note: the gcwr rating includes a 150 lbs (68 kg) allowance for the presence of a driver. Gross axle weight rating (gawr) the gawr is the maximum capacity of the fr...

  • Page 560

    Trailer sway control the trailer sway control can be a mechanical telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable fric- tion associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveli...

  • Page 561

    Warning! • an improperly adjusted weight-distributing hitch system may reduce handling, stability, and braking performance, and could result in a collision. • weight-distributing hitch systems may not be com- patible with surge brake couplers. Consult with your hitch and trailer manufacturer or a re...

  • Page 562

    With weight-distributing hitch (correct) improper adjustment of weight-distributing hitch (incorrect) 560 starting and operating.

  • Page 563

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 564

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine model frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l 4x2 40 sq ft (3.72 sq m) 5,000 lbs (2 268 kg) 500 ...

  • Page 565

    To side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions. Never exceed the maximum tongue weight stamped on your trailer hitch. Consider the following items when computing the weight on the rear axle of the...

  • Page 566

    Caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. Thi...

  • Page 567

    Warning! (continued) • safety chains must always be used between your vehicle and trailer. Always connect the chains to the hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parked on a gr...

  • Page 568

    • check the trailer tires for proper tire inflation pres- sures before trailer usage. • check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “starting and operating” for the proper inspection procedure. • when replacing tires, refer t...

  • Page 569

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 570

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 571

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic. Automatic transmission the drive range can be selected when towing. The transmission controls include an adaptive drive strategy to avoid frequent shifting when towing....

  • Page 572

    Cooling system to reduce potential for engine and transmission over- heating, take the following actions: city driving when stopped for short periods of time, shift the trans- mission into neutral and increase engine idle speed. Highway driving reduce speed. Air conditioning turn off temporarily. Sn...

  • Page 573

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheel off the ground two-wheel drive models four-wheel drive models flat tow none not allowed see instructions • transmission in park • transfer case in neu- tral (n) • tow in forward direc- tion...

  • Page 574

    Must be fastened to the axles (not to the body). Failure to follow these instructions may cause fault codes to be set and/or cause loss of proper tie-down tension. Recreational towing – two-wheel drive models do not flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (fo...

  • Page 575

    Recreational towing – quadra-trac i® (single-speed transfer case) four-wheel drive models recreational towing is not allowed. These models do not have a neutral (n) position in the transfer case. Note: this vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are off the gro...

  • Page 576

    Caution! (continued) • the transmission must be in park for recreational towing. • before recreational towing, perform the procedure outlined under “shifting into neutral (n)” to be certain that the transfer case is fully in neu- tral (n). Otherwise, internal damage will result. • failure to follow ...

  • Page 577

    Caution! It is necessary to follow these steps to be certain that the transfer case is fully in neutral (n) before recreational towing to prevent damage to internal parts. 1. Bring the vehicle to a complete stop and shift the transmission into park. 2. Turn the engine off. 3. For vehicles with keyle...

  • Page 578

    7. Using the point of a ballpoint pen or similar object, press and hold the recessed transfer case neutral (n) button (located by the selector switch) for four seconds. The light behind the n symbol will blink, indicating shift in progress. The light will stop blinking (stay on solid) when the shift...

  • Page 579

    11. Release the brake pedal for five seconds and ensure that there is no vehicle movement. 12. Turn the engine off, then turn the ignition switch back to the on/run position without starting the engine. 13. Firmly apply the parking brake. 14. Shift the transmission into park. Caution! Damage to the ...

  • Page 580

    • a flashing neutral (n) position indicator light indicates that shift requirements have not been met. Shifting out of neutral (n) use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply...

  • Page 581

    Note: when shifting out of transfer case neu- tral (n), turning the engine off may be required to avoid gear clash. 9. After the neutral (n) indicator light turns off, release the neutral (n) button. 10. After the neutral (n) button has been released, the transfer case will shift to the position ind...

  • Page 582

    Note: • steps 1 through 7 are requirements that must be met prior to pressing the neutral (n) button, and must continue to be met until the shift has been completed. If any of these requirements are not met prior to pressing the neutral (n) button or are no longer met during the shift, the neutral (...

  • Page 583: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .582 䡵 if your engine overheats . . . . . . . . . . . .582 䡵 jacking and tire changing . . . . . . . . . .583 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . .584 ▫ spare tire stowage . . . . . . . . . . ....

  • Page 584

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency...

  • Page 585

    Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads hot (h), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on hot (h), and you hear conti...

  • Page 586

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack location the scissor-type jack and tire changin...

  • Page 587

    Preparations for jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery surfaces. Warning! Do not attempt to change a tire on the side of the vehicle closest to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Turn...

  • Page 588

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 589

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left, one turn, while the whee...

  • Page 590

    Caution! Do not attempt to raise vehicle by jacking on loca- tions other than those indicated in the jacking in- structions for this vehicle. 4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do n...

  • Page 591

    5. For a rear tire, place the jack in the slot on the rear tie-down bracket, just forward of the rear tire (as indicated by the triangular lift point symbol on the sill molding). Do not raise the vehicle until you are sure the jack is fully engaged. Front jacking location lift point symbol on sill m...

  • Page 592

    6. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum sta- bility. Warning! Raising the vehicle higher than necessary can make the vehicle ...

  • Page 593

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 9. Lower the vehicle by turning the jack screw counter- clockwise, and remove the jack and wheel blocks....

  • Page 594

    12. Remove the small center cap and securely store the road wheel in the cargo area. 13. Have the aluminum road wheel and tire repaired as soon as possible, properly secure the spare tire with the special wing nut torqued to 3.7 ft-lbs (5 n·m), reinstall the jack and tool kit foam tray, and latch th...

  • Page 595

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tightening the...

  • Page 596

    Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or electrical system may occur. Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode ...

  • Page 597

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 598

    Jump-starting procedure warning! Failure to follow this procedure could result in per- sonal injury or property damage due to battery ex- plosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect th...

  • Page 599

    Once the engine is started, remove the jumper cables in the reverse sequence: 6. Disconnect the negative (-) jumper cable from the remote negative (-) post of the discharged vehicle. 7. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. 8. Disconne...

  • Page 600

    Note: shifts between drive and reverse can only be achieved at wheel speeds of 5 mph or less. Whenever the transmission remains in neutral for more than 2 sec- onds, you must press the brake pedal to engage drive or reverse. Use the least amount of accelerator pedal pressure that will maintain the r...

  • Page 601

    Caution! (continued) • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no trans- mission shifting occurring). Warning! Fast spinning tires can be dangerous....

  • Page 602

    Caution! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. Shift lever override if a malfunction occurs and the shift lever cannot be moved out of the park position, you can use the...

  • Page 603

    8. The vehicle may then be started in neutral. 9. Reinstall the shift lever override access cover and cupholder liner. Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. If the trans- mission and drivetrain are operable, disa...

  • Page 604

    Towing condition wheels off the ground 2wd models 4wd models flat tow none if transmission is operable: • transmission in neutral • 30 mph (48 km/h) max speed • 15 miles (24 km) max distance see instructions in “recreational tow- ing” under “starting and operating” • transmission in park • transfer ...

  • Page 605

    Caution! Do not use sling type equipment when towing. When securing the vehicle to a flat bed truck, do not attach to front or rear suspension components. Dam- age to your vehicle may result from improper towing. Without the key fob special care must be taken when the vehicle is towed with the ignit...

  • Page 606

    Caution! Towing this vehicle in violation of the above require- ments can cause severe transmission damage. Dam- age from improper towing is not covered under the new vehicle limited warranty. Four-wheel drive models the manufacturer recommends towing with all wheels off the ground. Acceptable metho...

  • Page 607: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . .607 䡵 engine compartment — 5.7l . . . . . . . . . .608 䡵 onboard diagnostic system (obd ii) . . .609 ▫ loose fuel filler cap message . . . . . . . . . . . .609 䡵 emissions inspection and maintenance programs . . . . . ....

  • Page 608

    ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . .634 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . .635 ▫ automatic transmission . . . . . . . . . . . . . . . .636 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . .640 䡵 fuses . . . ....

  • Page 609

    Engine compartment — 3.6l 1 — totally integrated power module (fuses) 6 — air cleaner filter 2 — engine oil dipstick 7 — washer fluid reservoir 3 — engine oil fill 8 — coolant pressure cap (radiator) 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — power steering fluid reservoir 7 maintain...

  • Page 610

    Engine compartment — 5.7l 1 — totally integrated power module (fuses) 6 — washer fluid reservoir 2 — automatic transmission dipstick 7 — engine oil dipstick 3 — engine oil fill 8 — coolant pressure cap (radiator) 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — air cleaner filter 608 maint...

  • Page 611

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 612

    “understanding your instrument panel” for further in- formation. Tighten the fuel filler cap properly and press the select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap...

  • Page 613

    4. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 614

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 615

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 616

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for further informa- tion. Note:under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km) or twelve mont...

  • Page 617

    Engine oil viscosity – 3.6l engine sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil ...

  • Page 618

    Disposing of used engine oil and oil filters care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service station or governmental agency ...

  • Page 619

    Engine air cleaner filter selection the quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar® engine air cleaner filters are a high quality filter and are recom- mended. Maintenance-free battery your v...

  • Page 620

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and are identified on the battery case. Cable clamps should b...

  • Page 621

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 622

    The a/c air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1. Open the glove compartment and remove all contents. 2. Push in on the sides of the glove compartment and lower the door. 3. Pivot the glove compartment downward. 4. ...

  • Page 623

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7. Rotate the glove compartment door back into position. Body lubrication locks and all body pivot points...

  • Page 624

    Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may ...

  • Page 625

    3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. 4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade an...

  • Page 626

    When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperat...

  • Page 627

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 628

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 629

    Cooling system warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiat...

  • Page 630

    Cooling system – drain, flush, and refill if the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with oat coolant only. Properly dispose of the old engine coolant (antifreeze) solution. Refer to the “maintenance schedule” for the proper maintenance...

  • Page 631

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 632

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: mixing engine coolant (antifreeze) types is not recommended and can result in cooling system dama...

  • Page 633

    Rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. ...

  • Page 634

    If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • do not overfill the coolant expansion bottle. • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine c...

  • Page 635

    Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency...

  • Page 636

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 637

    The front axle fill and drain plugs should be tightened to 22 to 29 ft lbs (30 to 40 n·m). Caution! Do not over tighten the plugs as it could damage them and cause them to leak. Rear axle fluid level check the rear axle oil level needs to be between 1/8 in (3 mm) below the bottom of the fill hole an...

  • Page 638

    Adding fluid add fluid at the filler hole, until it runs out of the hole, when the vehicle is in a level position. Drain first remove fill plug, then remove drain plug. Recom- mended tightening torque for drain and fill plugs is 15 to 25 ft lbs (20 to 34 n·m). Caution! When installing plugs, do not ...

  • Page 639

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for fluid speci- fications. Special additives th...

  • Page 640

    Caution! • if a transmission fluid leak occurs, visit your au- thorized dealer immediately. Severe transmission damage may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid level check – 5.7l engine it is best to check the fluid level when the transmissio...

  • Page 641

    Use only the recommended fluid (see ⬙fluids, lubri- cants, and genuine parts ⬙ for fluid specifications). After adding any quantity of oil through the dipstick tube, wait a minimum of two minutes for the oil to fully drain into the transmission before rechecking the fluid level. Note: if it is neces...

  • Page 642

    In addition, change the fluid and filter if the transmission is disassembled for any reason. Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable...

  • Page 643

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover to remove. • use a high quality cleaner wax, such as mopar® cleaner wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • av...

  • Page 644

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • use mopar® touch up paint on scratches as soon as possible. You...

  • Page 645

    • for tough stains, apply mopar® total clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar® multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap resid...

  • Page 646

    Cleaning headlights your vehicle is equipped with plastic headlights and fog lights (if equipped) that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize...

  • Page 647

    Seat belt maintenance do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use mopar® total clean, a mild soap solution, or lukewarm water. Do not remove the belts from the ...

  • Page 648

    Cavity car- tridge fuse mini fuse description j01 40 amp green air suspension j02 30 amp pink power liftgate module j03 30 amp pink trailer tow j04 25 amp natural driver door node j05 25 amp natural passenger door node j06 40 amp green antilock brakes pump/stability control system cavity car- tridge...

  • Page 649

    Cavity car- tridge fuse mini fuse description j13 60 amp yellow main ignition off draw (iod) j14 20 amp blue trailer tow lamps/park lamps j15 40 amp green front cabin fan/ blower j17 40 amp green starter motor solenoid j18 20 amp blue powertrain control module/powertrain control module/ transmission...

  • Page 650

    Cavity car- tridge fuse mini fuse description m3 20 amp yellow liftgate/headrest m5 25 amp natural 115v ac power inverter m6 20 amp yellow cigar lighter m7 20 amp yellow power outlet #2 (switchable) m8 20 amp yellow front heated seat & steering wheel m9 20 amp yellow rear heated seats cavity car- tr...

  • Page 651

    Cavity car- tridge fuse mini fuse description m15 20 amp yellow power seat module(s)/ adaptive cruise control/audio telematics/ daytime running lights relay/air suspension module/instrument cluster m16 10 amp red occupant restraint controller m18 15 amp blue stop lamp cavity car- tridge fuse mini fu...

  • Page 652

    Cavity car- tridge fuse mini fuse description m25 20 amp yellow fuel pump motor output/diesel lift pump (export only) m26 10 amp red driver door switch bank m27 10 amp red ignition switch/ wireless control module/keyless entry module m28 15 amp blue powertrain controller/ transmission controller cav...

  • Page 653

    Cavity car- tridge fuse mini fuse description m34 10 amp red park assist module/climate control system module/infra red sensor/compass module m35 15 amp blue left rear parklamps m36 20 amp yellow power outlet m37 10 amp red antilock brakes/ stability control system module m38 25 amp natural all door...

  • Page 654

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • remove fuse #j13 in the totally integrated power module (tipm) labeled main ignition-off draw (iod). • or, disconnect the negative cable from the battery. • an...

  • Page 655

    Exterior bulbs bulb number headlamps (low beam) h11 headlamps (high beam) 9005 headlamps (low beam) – high intensity discharge (hid) d1s (serviced at authorized dealer) daytime running lamp (drl) 3157k front fog lamps psx24w front side marker 194 front park/turn lamp 7444na aux aperature backup lamp...

  • Page 656

    Warning! A transient high voltage occurs at the bulb sockets of high intensity discharge (hid) headlamps when the headlamp switch is turned on. It may cause serious electrical shock or electrocution if not serviced prop- erly. See your authorized dealer for service. Note: on vehicles equipped with h...

  • Page 657

    Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front fog lamps 1. Reach through the cutout in the splash shield and disconnect the wiring harness from th...

  • Page 658

    6. Firmly and evenly push the bulb straight into the lamp housing until both tabs snap firmly into place and are fully engaged. 7. Connect the wiring harness to the front fog lamp connector. Rear tail, stop, turn signal, and backup lamps 1. Raise the liftgate. 2. Remove the two push-pins from the ta...

  • Page 659

    Rear liftgate mounted tail lamp 1. Raise the liftgate. 2. Use a fiber stick or flat blade screw driver to pry the lower trim from the liftgate. 3. Once lower trim is loose, close the liftgate. 4. Open the flipper glass. 5. Pull up glass seal at bottom of window opening. 6. Remove small trim panel ar...

  • Page 660

    Center high-mounted stop lamp (chmsl) the center high-mounted stop lamp is an led assembly. See your authorized dealer for replacement. Rear license lamp 1. Use a screw driver to gently pry against the side of the snap tab to remove the license lamp lens. 2. Pull bulb from socket. 3. Replace bulb. 4...

  • Page 661

    Fluid capacities u.S. Metric fuel (approximate) 3.6l and 5.7l engines 25 gallons 94 liters engine oil with filter 3.6l engine (sae 5w-20, api certified) 6 quarts 5.6 liters 5.7l engine (sae 5w-20, api certified) 7 quarts 6.6 liters cooling system* 3.6l engine (mopar® antifreeze/engine coolant 10 yea...

  • Page 662

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology). Engine oil – 3.6l engine we recommend you use api certified sae 5w-20 engine oil, meet...

  • Page 663

    Chassis component fluid, lubricant, or genuine part automatic transmission we recommend you only use mopar® atf+4® automatic transmission fluid. Failure to use atf+4 fluid may affect the function or performance of your transmission. Transfer case – single-speed (quadra-trac i®) we recommend you use ...

  • Page 664

    Component fluid, lubricant, or genuine part brake master cylinder we recommend you use mopar® dot 3 brake fluid, sae j1703 should be used. If dot 3, sae j1703 brake fluid is not available, then dot 4 is acceptable. Power steering reservoir – 3.6l engine we recommend you use mopar® hydraulic fluid. P...

  • Page 665: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .664 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .666 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 666

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 667

    • check the fluid levels of the coolant reservoir, brake master cylinder, power steering and transmission as needed • check function of all interior and exterior lights required maintenance refer to the maintenance schedules on the following pages for required maintenance. At every oil change interv...

  • Page 668

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176...

  • Page 669

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 670

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 671

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 673: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .673 ▫ prepare for the appointment. . . . . . . . . . . . .673 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .673 ▫ be reasonable with requests ....

  • Page 674

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .679 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .679 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .679 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .680 672 if...

  • Page 675

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 676

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 677

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 678

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 679

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 680

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 681

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 682

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 683: Index

    Index 10

  • Page 684

    Adaptive cruise control (acc) (cruise control) . . .218 adding engine coolant (antifreeze) . . . . . . . . . . . .629 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .550 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .544 airbag. . . . . . . . . . . . . . . ...

  • Page 685

    Fluid and filter changes . . . . . . . . . . . . . . . . .639 fluid change . . . . . . . . . . . . . . . . . . . . . . . . .639 fluid level check . . . . . . . . . . . . . . . . . . . . . .636 fluid type . . . . . . . . . . . . . . . . . . . . . . . . . . .636 special additives . . . . . . . . . . ....

  • Page 686

    Cargo area cover . . . . . . . . . . . . . . . . . . . . . . . . .290 cargo area features . . . . . . . . . . . . . . . . . . . . . . .287 cargo compartment . . . . . . . . . . . . . . . . . . . . . . .287 light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .288 cargo light . . . . . ....

  • Page 687

    Cooling system. . . . . . . . . . . . . . . . . . . . . . . . . . .627 adding coolant (antifreeze) . . . . . . . . . . . . . . .629 coolant capacity . . . . . . . . . . . . . . . . . . . . . . .659 coolant level . . . . . . . . . . . . . . . . . . . . . . . . .631 disposal of used coolant . . . . . ...

  • Page 688

    Electric rear window defrost. . . . . . . . . . . . . . . . .294 electric remote mirrors . . . . . . . . . . . . . . . . . . . . .125 electronic brake control system . . . . . . . . . . . . . . .494 brake assist system . . . . . . . . . . . . . . . . . . . . .495 electronic roll mitigation (erm) . ....

  • Page 689

    Event data recorder . . . . . . . . . . . . . . . . . . . . . . . .82 exhaust gas caution. . . . . . . . . . . . . . . . . . . . . . . .50 exhaust system. . . . . . . . . . . . . . . . . . . . . . . . . . .110 exterior lights . . . . . . . . . . . . . . . . . . . . . . . . . . .113 filters air clean...

  • Page 690

    Four wheel drive operation . . . . . . . . . . . . . . . . .467 freeing a stuck vehicle . . . . . . . . . . . . . . . . . . . . .597 front axle (differential). . . . . . . . . . . . . . . . . . . . .634 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .541 adding . . . . . . ...

  • Page 691

    Gear select lever override . . . . . . . . . . . . . . . . . .600 general information . . . . . . . . . . . . . . . . . . . . . . . .20 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .644 gross axle weight rating . . . . . . . . . . . . . . . . . . .557 gross vehicle weight ratin...

  • Page 692

    Integrated power module (fuses) . . . . . . . . . . . . . .645 interior appearance care . . . . . . . . . . . . . . . . . . . .643 intermittent wipers (delay wipers). . . . . . . . . . . . .208 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 inverter, power . . . . . . . . ...

  • Page 693

    Bulb replacement . . . . . . . . . . . . . . . . . . . . . .653 cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .288 center mounted stop . . . . . . . . . . . . . . . . . . . .658 daytime running . . . . . . . . . . . . . . . . . . . . . .200 dimmer switch, headlight . . . . . . . ...

  • Page 694

    Power door . . . . . . . . . . . . . . . . . . . . . . . . . . .35 lubrication, body . . . . . . . . . . . . . . . . . . . . . . . . .621 maintenance free battery. . . . . . . . . . . . . . . . . . . .617 maintenance procedures . . . . . . . . . . . . . . . . . . . .612 maintenance schedule . . . . ...

  • Page 695

    Off-road driving (off-pavement) . . . . . . . . . . . . . .482 oil change indicator . . . . . . . . . . . . . . . . . . . . . . .328 oil change indicator, reset . . . . . . . . . . . . . . . . . .328 oil, engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .613 capacity . . . . . . . . ...

  • Page 696

    Power door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .281 lift gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 outlet (au...

  • Page 697

    Recreational towing . . . . . . . . . . . . . . . . . . . . . . .571 shifting into transfer case neutral (n) . . . . . . .574 shifting out of transfer case neutral (n) . . . . . .578 reformulated gasoline . . . . . . . . . . . . . . . . . . . . .542 refrigerant . . . . . . . . . . . . . . . . . . . ...

  • Page 698

    Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . .63 reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . .308 shoulder belt anchorage . . . . . . . . . . . . . . . . . .60 untwisting procedure . . . . . ....

  • Page 699

    Cold weather . . . . . . . . . . . . . . . . . . . . . . . . .443 engine block heater . . . . . . . . . . . . . . . . . . . . .445 engine fails to start . . . . . . . . . . . . . . . . . . . . .443 remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 starting and operating . . . . ...

  • Page 700

    General information . . . . . . . . . . . . . . . . . . . . .518 high speed . . . . . . . . . . . . . . . . . . . . . . . . . . .521 inflation pressures . . . . . . . . . . . . . . . . . . . . . .519 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . .526 load capacity . . . . . . . ....

  • Page 701

    Trailer weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .562 transfer case . . . . . . . . . . . . . . . . . . . . . . . . . . . .635 maintenance . . . . . . . . . . . . . . . . . . . . . . . . . .635 transmission automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .448 main...

  • Page 702

    Warning flasher, hazard . . . . . . . . . . . . . . . . . . . .582 warning, roll over . . . . . . . . . . . . . . . . . . . . . . . . .5 warnings and cautions. . . . . . . . . . . . . . . . . . . . . . .8 warranty information . . . . . . . . . . . . . . . . . . . . . .676 washers, windshield . . . ....

  • Page 703

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed prop- erly by trained personnel. The following must be obs...

  • Page 704

    Grand cherokee chrysler group llc o w n e r ’ s m a n u a l 20 13 gr and cher ok ee 13wk741-126-ae fifth edition printed in u.S.A. 2 0 1 3.