1. DL manuals
  2. Jeep
  3. Automobile
  4. 2016 CHEROKEE
  5. Owner's Manual

Jeep 2016 CHEROKEE Owner's Manual

Summary of 2016 CHEROKEE

  • Page 1

    Grand cherokee o w n e r ’ s m a n u a l 20 16 gr and cher ok ee first edition rev 1 printed in u.S.A. 16wk741-126-aa ©2015 fca us llc. All rights reserved. Jeep is a registered trademark of fca us llc. 2 0 1 6 stick with the specialists ®.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 understan...

  • Page 5

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .5 䡵 how to use this manual . . . . . . . . . . . . . .6 䡵 warnings and cautions . . . . . . . . . . . . . .8 䡵 vehicle identification number . . . . . . . .8 ...

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle. It can go places and perform tasks that co...

  • Page 7

    This owner’s manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by warranty information, and various customer-oriented documents. Please take the time to read these publications ...

  • Page 8

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million a...

  • Page 9

    1 introduction 7.

  • Page 10

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision, bodily injury and/or death. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss...

  • Page 11

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 1 introduct...

  • Page 13

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .14 ▫ keyless push button ignition . . . . . . . . . . . . . .14 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 ▫ ignition or accessory on message . . . . . . . . . .16 ▫ gene...

  • Page 14

    ▫ programming additional transmitters . . . . . . .26 ▫ transmitter battery replacement . . . . . . . . . . .26 ▫ general information . . . . . . . . . . . . . . . . . . . .28 䡵 remote starting system — if equipped . .28 ▫ how to use remote start . . . . . . . . . . . . . . . .29 ▫ remote start abor...

  • Page 15

    ▫ seat belt systems . . . . . . . . . . . . . . . . . . . . . .53 ▫ supplemental restraint system (srs) . . . . . . . .69 ▫ child restraints . . . . . . . . . . . . . . . . . . . . . . .84 ▫ transporting pets . . . . . . . . . . . . . . . . . . . . .109 䡵 engine break-in recommendations . . .109 䡵 s...

  • Page 16

    A word about your keys your vehicle uses a keyless ignition system. This system consists of a key fob with remote keyless entry (rke) transmitter and a keyless push button ignition. Keyless push button ignition this feature allows the driver to operate the ignition switch with the push of a button, ...

  • Page 17

    Key fob the key fob also contains the remote keyless entry (rke) transmitter and an emergency key, which stores in the rear of the key fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the key fob go dead. The emergency key is also for locking the glove bo...

  • Page 18

    Note: you can insert the double-sided emergency key into the lock cylinders with either side up. Ignition or accessory on message when opening the driver’s door when the ignition is in acc or on (engine not running), a chime will sound to remind you to cycle the ignition to off. In addition to the c...

  • Page 19

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n-go in the acc or on/run mode. A child could operate power windows, other con- trols, or move the vehicle. • do not...

  • Page 20

    Sentry key the sentry key immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses a key fob with a factory-mated remote ke...

  • Page 21

    Caution! The sentry key immobilizer system is not compat- ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the key fobs provided with your new vehicle have been programmed to the vehicle electroni...

  • Page 22

    Customer key programming programming key fobs or rke transmitters may be performed at an authorized dealer. General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industr...

  • Page 23

    To arm the system follow these steps to arm the vehicle security alarm: 1. Make sure the vehicles ignition is cycled to the “off” position (refer to ⬙starting procedures⬙ in ⬙starting and operating ⬙ for further information). • for vehicles equipped with keyless enter-n-go, make sure the vehicle ign...

  • Page 24

    • cycle the vehicle ignition system out of the off position. • for vehicles equipped with keyless enter-n-go, push the keyless enter-n-go start/stop button (requires at least one valid key fob in the vehicle). • for vehicles not equipped with keyless enter-n-go, insert a valid key into the ignition ...

  • Page 25

    Tamper alert if something has triggered the vehicle security alarm in your absence, the horn will sound three times and the exterior lights will blink three times when you disarm the vehicle security alarm. Check the vehicle for tampering. Illuminated entry — if equipped the courtesy lights will tur...

  • Page 26

    Note: driving at speeds 5 mph (8 km/h) and above disables the system from responding to all rke transmit- ter buttons for all rke transmitters. To unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door or twice within five seconds to ...

  • Page 27

    Flash lamps with lock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, refer to “uconnect settings” in “un- derstanding your instrument panel” for furt...

  • Page 28

    Using the panic alarm to turn the panic alarm feature on or off, push and hold the panic button on the rke transmitter for at least one second and release. When the panic alarm is activated, the turn signals will flash, the horn will pulse on and off, and the interior lights will turn on. The panic ...

  • Page 29

    • used batteries are harmful to the environment. You can dispose of them either in the correct containers as specified by law or by taking them to a dealership, which will deal with their disposal. • do not touch the battery terminals that are on the back housing or the printed circuit board. 1. Rem...

  • Page 30

    New battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To assemble the rke transmitter case, snap the two halves together. General information the following regulatory statement applies to all radio frequency (rf) devices e...

  • Page 31

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • hazard switch off • brake switch inactive (brake pedal not pressed) • battery at an acceptable charge level • rke panic button not pushed • fu...

  • Page 32

    • remote start cancelled — hood open • remote start cancelled — fuel low • remote start cancelled — system fault • remote start disabled — start vehicle to reset the did message stays active until the ignition is turned to the on/run position. To enter remote start mode push and release the remote s...

  • Page 33

    Note: to avoid unintentional shut downs, the system will disable the one time push of the remote start button for two seconds after receiving a valid remote start request. To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, push and release the unlock button on the...

  • Page 34

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada licence-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 35

    Warning! • for personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • before exiting a vehicle, always shift the transmis- sion into park, apply the parking brake, turn the engine off, remove the key fob fro...

  • Page 36

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 37

    If a rear door is locked, it cannot be opened from inside the vehicle without first unlocking the door. The door may be unlocked manually by raising the lock knob. Automatic door locks — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock autom...

  • Page 38

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged (locked). Child-protection door lock location child-protection door lock function 36 things to know before starting your vehicle.

  • Page 39

    Note: for emergency exit from the rear seats when the child-protection door lock system is engaged, manually raise the door lock knob to the unlocked position, roll down the window, and open the door using the outside door handle. Keyless enter-n-go the passive entry system is an enhancement to the ...

  • Page 40

    Note: if “unlock all doors 1st press” is programmed all doors will unlock when you grab hold of the driver’s front door handle. To select between “unlock driver door 1st press” and “unlock all doors 1st press,” refer to “uconnect settings” in “understanding your instrument panel” for further informa...

  • Page 41

    If one of the vehicle doors is open and the door panel switch is used to lock the vehicle, once all open doors have been closed the vehicle checks the inside and outside of the vehicle for any valid passive entry rke transmitters. If one of the vehicle’s passive entry rke transmitters is detected in...

  • Page 42

    To lock the liftgate with a valid passive entry rke transmitter within 3 ft (1.0 m) of the liftgate, push the passive entry lock button located to the right of electronic liftgate release. Note: if “unlock all doors 1st press” is programmed in uconnect settings, all doors will unlock when you push t...

  • Page 43

    Note: the key must be within 5 ft (1.5 m) of the handle being used to lock the vehicle. Do not grab the door handle, when pushing the door handle button. This could unlock the door(s). Push the door handle button to lock do not grab the door handle when locking 2 things to know before starting your ...

  • Page 44

    Note: • after pushing the door handle button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle without the vehicle reacting and unlocking. • the passive en...

  • Page 45

    Windows power windows the power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door and rear doors which operate the front and rear door windows. The window controls will oper- ate only when the ignition switch is in the on/run or acc pos...

  • Page 46

    Warning! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter- n-go in the acc or on/run mode. Oc...

  • Page 47

    Auto up feature with anti-pinch protection — driver and front passenger door only lift the window switch fully upward to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the “auto up” operation, push down on the switch briefly. ...

  • Page 48

    Note: if the window runs into any obstacle during “auto up,” it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. Any impact due to rough road conditions may trigger the auto reverse function unex- pectedly during “auto-up.” if thi...

  • Page 49

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 50

    Note: if “unlock all doors 1st press” is programmed in uconnect settings, all doors will unlock when you push the electronic liftgate release. If ⬙unlock driver door 1st press ⬙ is programmed in uconnect settings, only the liftgate will unlock when you push the electronic liftgate release. For furth...

  • Page 51

    Warning! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Power liftgate — if equipped the power liftgate may be opened by pushing the electronic...

  • Page 52

    Note: • in the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the lift- gate trim panel. • if liftgate is left open for an extended period of t...

  • Page 53

    • if the electronic liftgate release is pushed while the power liftgate is closing, the liftgate will reverse to the full open position. • if the electronic liftgate release is pushed while the power liftgate is opening, the liftgate motor will dis- engage to allow manual operation. • if the power l...

  • Page 54

    Important safety precautions please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible. Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. C...

  • Page 55

    Side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured. 9. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the customer center. Phone numbers are provided under ⬙if you need assistance.⬙ ...

  • Page 56

    Their seat belts. The belt alert feature is active when- ever the ignition switch is in the start or on/run position. Initial indication if the driver is unbuckled when the ignition switch is first turned to the start or on/run position, an intermit- tent chime will signal for a few seconds. If the ...

  • Page 57

    Change of status if the driver or outboard front seat passenger (if equipped with outboard front passenger seat beltalert) unbuckles their seat belt while the vehicle is traveling, the beltalert warning sequence will begin until the seat belts are buckled again. The outboard front passenger seat bel...

  • Page 58

    Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • in a collision, you and your p...

  • Page 59

    Warning! (continued) • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not pro...

  • Page 60

    Warning! (continued) • a frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be re- placed immediately. Do not disassemble or modify the seat belt system. Sea...

  • Page 61

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 62

    6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Lap/shoulder belt untwisting procedure use the following procedure to untwist...

  • Page 63

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 64

    Warning! • only use a seat belt extender if it is physically required in order to properly fit the original seat belt system. Do not use the seat belt extender if, when worn, the distance between the front edge of the seat belt extender buckle and the center of the occupant’s body is less than 6 inc...

  • Page 65

    Position the lap belt snug and low below the abdomen and across the strong bones of the hips. Place the shoulder belt across the chest and away from the neck. Never place the shoulder belt behind the back or under the arm. Seat belt pretensioner the front seat belt system is equipped with pretension...

  • Page 66

    Restraints” section of this manual. The table below defines the type of feature for each seating position. • alr = switchable automatic locking retractor if the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to co...

  • Page 67

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 68

    Warning! (continued) • do not use the automatic locking mode to restrain occupants who are wearing the seat belt or children who are using booster seats. The locked mode is only used to install rear-facing or forward-facing child restraints that have a harness for restraining the child. Supplemental...

  • Page 69

    Warning! • all occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. • do not place items over the top of the active head restra...

  • Page 70

    Warning! (continued) as loose cargo could contact the active head re- straint during sudden stops. Failure to follow this warning could cause personal injury if the active head restraint is deployed. Note: for more information on properly adjusting and positioning the head restraint, refer to “adjus...

  • Page 71

    Warning! Deployed ahrs are not able to best protect you in all types of collisions. Have deployed ahrs reset by an authorized dealer immediately. Supplemental restraint system (srs) air bag system components your vehicle may be equipped with the following air bag system components: • occupant restra...

  • Page 72

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 73

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 74

    Advanced front air bag operation advanced front air bags are designed to provide addi- tional protection by supplementing the seat belts. Ad- vanced front air bags are not expected to reduce the risk of injury in rear, side, or rollover collisions. The ad- vanced front air bags will not deploy in al...

  • Page 75

    Knee impact bolsters the knee impact bolsters help protect the knees of the driver and front passenger, and position the front occu- pants for improved interaction with the advanced front air bags. Warning! • do not drill, cut, or tamper with the knee impact bolsters in any way. • do not mount any a...

  • Page 76

    The sabs may help to reduce the risk of occupant injury during certain side impacts and/or vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover...

  • Page 77

    2. Supplemental side air bag inflatable curtains (sabics): located above the side windows. The trim covering the sabics is labeled “srs airbag” or “airbag.” sabics may help reduce the risk of head or other injuries to front and rear seat outboard occupants in certain side impacts and/or vehicle roll...

  • Page 78

    Warning! • your vehicle is equipped with left and right supplemental side air bag inflatable curtains (sabics). Do not stack luggage or other cargo up high enough to block the deployment of the sabics. The trim covering above the side win- dows where the sabic and its deployment path are located sho...

  • Page 79

    Seat belts (and child restraints where appropriate) are necessary for your protection in all collisions. They also help keep you in position, away from inflating side air bags. To get the best protection from the side air bags, occupants must wear their seat belts properly and sit upright with their...

  • Page 80

    Deploys the left side air bags only and a right side impact deploys the right side air bags only. The side air bags will not deploy in all side collisions, including some collisions at certain angles, or some side collisions that do not impact the area of the passenger compartment. The side air bags...

  • Page 81

    If you do have a collision which deploys the air bags, any or all of the following may occur: • the air bag material may sometimes cause abrasions and/or skin reddening to the occupants as the air bags deploy and unfold. The abrasions are similar to fric- tion rope burns or those you might get slidi...

  • Page 82

    • after any collision, the vehicle should be taken to an authorized dealer immediately. Enhanced accident response system in the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the orc will determine whether to have...

  • Page 83

    The off position or in the acc position, the air bag system is not on and the air bags will not inflate. The orc contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. The orc turns on the air bag warning lig...

  • Page 84

    Warning! Ignoring the air bag warning light in your instru- ment panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first placed in the on position, and stays on after you start the vehicle, or if it comes on...

  • Page 85

    Warning! (continued) modify the front bumper, vehicle body structure, or add aftermarket side steps or running boards. • it is dangerous to try to repair any part of the air bag system yourself. Be sure to tell anyone who works on your vehicle that it has an air bag system. • do not attempt to modif...

  • Page 86

    These data can help provide a better understanding of the circumstances in which crashes and injuries occur. Note: edr data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the edr under normal driving conditions and no per- sonal data (e.G., name, g...

  • Page 87

    Warning! (continued) great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size. There are different sizes and types of restraints for children from newborn ...

  • Page 88

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 89

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 90

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 91

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 92

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 93

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 94

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 92 things to know before starting your vehicle.

  • Page 95

    Frequently asked questions about installing child restraints with latch what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child...

  • Page 96

    Frequently asked questions about installing child restraints with latch can two child restraints be at- tached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the se...

  • Page 97

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if...

  • Page 98

    Locating tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. To access them, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchorages. Pulling down the carpet floor panel to access top t...

  • Page 99

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing child restraints...

  • Page 100

    Center arm rest tether for rear-facing child restraints secured in the center seat position with the vehicle seat belts, the rear center seat position has an armrest tether that secures the arm rest in the upward position. 1. To access the center seat arm rest tether, first lower the arm rest. The t...

  • Page 101

    Always follow the directions of the child restraint manu- facturer when installing your child restraint. Not all child restraint systems will be installed as described here. To install a latch-compatible child restraint if the selected seating position has a switchable auto- matic locking retractor ...

  • Page 102

    4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tions to attach a tether anchor. 5. Tighten all of the straps as you push the child restraint rearward and downward into the s...

  • Page 103

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 104

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • top tether anchorage symbol 102 things to know before starting your vehicle.

  • Page 105

    Frequently asked questions about installing child restraints with seat belts what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a for- ward facing child restraint? Weight limit of the child restraint always use the tet...

  • Page 106

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 107

    9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. Installing c...

  • Page 108

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 109

    3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If...

  • Page 110

    6. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • the top tether anchorages are not visible until the gap panel is folded down. Do not use the visible cargo tie down hooks, located on the floor behind the seats, to attach a child restraint t...

  • Page 111

    Transporting pets air bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by sea...

  • Page 112

    Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty. Please check your oil level with the engine oil indicator often during the break in perio...

  • Page 113

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 114

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 115

    Unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • alwa...

  • Page 116

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 117

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 ▫ inside day/night mirror — if equipped . . . .123 ▫ automatic dimming mirror — if equipped . . .123 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . .131 ▫ outside mir...

  • Page 118

    䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144 ▫ power seats — if equipped . . . . . . . . . . . . . .145 ▫ power lumbar — if equipped . . . . . . . . . . . .147 ▫ manual front seats forward/rearward adjustment . . . . . . . . . . . . . . . . . . . . . . . . .147 ▫ manual fro...

  • Page 119

    ▫ automatic headlight leveling — hid headlights only. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172 ▫ headlight delay . . . . . . . . . . . . . . . . . . . . . .172 ▫ parking lights and panel lights. . . . . . . . . . .173 ▫ fog lights — if equipped . . . . . . . . . . . . . . .173 ...

  • Page 120

    䡵 heated steering wheel — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .187 䡵 electronic speed control — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .188 ▫ to activate . . . . . . . . . . . . . . . . . . . . . . . . . .189 ▫ to set a desired speed . . . . . . . . . . ....

  • Page 121

    ▫ normal (fixed speed) electronic speed control mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215 䡵 forward collision warning (fcw) with mitigation — if equipped . . . . . . . . . . . .219 ▫ forward collision warning (fcw) with mitigation operation . . . . . . . . . . . . . . . . ....

  • Page 122

    ▫ parksense system usage precautions. . . . . . . .245 䡵 parkview rear back up camera — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .248 䡵 overhead console . . . . . . . . . . . . . . . . . .250 ▫ front map/reading lights — if equipped . . .251 ▫ courtesy lights . . . . . . . . ....

  • Page 123

    ▫ ignition off operation . . . . . . . . . . . . . . . . . .264 ▫ relearn procedure . . . . . . . . . . . . . . . . . . . . .265 䡵 commandview sunroof with power shade — if equipped . . . . . . . . . . . . . . . . .265 ▫ opening sunroof — express . . . . . . . . . . . . . .267 ▫ opening sunroof — ma...

  • Page 124

    ▫ cargo storage bins . . . . . . . . . . . . . . . . . . . .281 ▫ retractable cargo area cover — if equipped .283 ▫ rear cargo tie-downs . . . . . . . . . . . . . . . . .284 䡵 rear window features . . . . . . . . . . . . . .286 ▫ rear window wiper/washer . . . . . . . . . . . . .286 ▫ rear window de...

  • Page 125

    Mirrors inside day/night mirror — if equipped the mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirr...

  • Page 126

    Note: the automatic dimming mirror feature is dis- abled when the vehicle is in reverse gear to improve rear view viewing. The automatic dimming mirror feature can be turned on or off through the touchscreen. • push the mirror dimmer button once to turn the feature on. • push the mirror dimmer butto...

  • Page 127

    Warning! Always obey traffic laws and pay attention to the road. Some uconnect access services, including 9-1-1 and assist, will not work without an operable 1x (voice/data) or 3g (data) network connection. Note: • your vehicle may be transmitting data as authorized by the subscriber. • the 9–1–1 an...

  • Page 128

    Note: in case the 9-1-1 call button is pushed in error, there will be a 10 second delay before the 9-1-1 call system initiates a call to a 9-1-1 operator. To cancel the 9-1-1 call connection, push the 9-1-1 call button on the rearview mirror or press the cancellation button on the device screen. Ter...

  • Page 129

    Note: • your vehicle may be transmitting data as authorized by the subscriber. • once a connection is made between the vehicle’s 9-1-1 call system and the 9-1-1 operator, the 9-1-1 operator may be able to open a voice connection with the vehicle to determine if additional help is needed. Once the 9-...

  • Page 130

    Warning! (continued) • the 9-1-1 call system is embedded into the vehi- cle’s electrical system. Do not add aftermarket electrical equipment to the vehicle’s electrical sys- tem. This may prevent your vehicle from sending a signal to initiate an emergency call. To avoid inter- ference that can cause...

  • Page 131

    • the device screen will display the following message “vehicle device requires service. Please contact your dealer.” • an in-vehicle audio message will state “vehicle de- vice requires service. Please contact your dealer.” warning! • ignoring the rearview mirror light could mean you will not have 9...

  • Page 132

    • operator error by the 9-1-1 operator. • 1x (voice/data) or 3g (data) network congestion. • weather. • buildings, structures, geographic terrain, or tunnels. Warning! Always obey traffic laws and pay attention to the road. Some uconnect access services, including 9-1-1 and assist, will not work wit...

  • Page 133

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside mirrors to receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a...

  • Page 134

    Power folding outside mirrors — if equipped if equipped with power folding mirrors, they can be electrically folded rearward and unfolded into the drive position. The switch for the power folding mirrors is located between the power mirror switches l (left) and r (right). Press the switch once and t...

  • Page 135

    You want to adjust. Using the mirror control switch, push on any of the four arrows for the direction that you want the mirror to move. Power mirror preselected positions can be controlled by the optional memory seat feature. Refer to “driver memory seat” in “understanding the features of your vehic...

  • Page 136

    Tilt mirrors in reverse (available with memory seat only) — if equipped tilt mirrors in reverse provides automatic outside mirror positioning which will aid the drivers view of the ground rearward of the front doors. Outside mirrors will move slightly downward from the present position when the vehi...

  • Page 137

    Sun visor “slide-on-rod” feature — if equipped the sun visor “slide-on-rod” feature allows for addi- tional flexibility in positioning the sun visor to block out the sun. 1. Fold down the sun visor. 2. Unclip the visor from the center clip. 3. Pull the sun visor toward the inside rearview mirror to ...

  • Page 138

    The bsm detection zone covers approximately one lane width on both sides of the vehicle 12 ft (3.8 m). The zone length starts at the outside rear view mirror and extends approximately 10 ft (3 m) beyond the rear bumper of the vehicle. The bsm system monitors the detection zones on both sides of the ...

  • Page 139

    The bsm system notifies the driver of objects in the detection zones by illuminating the bsm warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “modes of operation” for further information. The bsm system monitors the...

  • Page 140

    Entering from the side vehicles that move into your adjacent lanes from either side of the vehicle. Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Side monitoring rear monitor...

  • Page 141

    Overtaking traffic if you pass another vehicle slowly with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h),...

  • Page 142

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects t...

  • Page 143

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm (continued) warning! (continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicles m...

  • Page 144

    Rcp monitors the rear detection zones on both sides of the vehicle, for objects that are moving toward the side of the vehicle with a minimum speed of approximately 3 mph (5 km/h), to objects moving a maximum of approximately 20 mph (32 km/h), such as in parking lot situations. Note: in a parking lo...

  • Page 145

    Modes of operation three selectable modes of operation are available in the uconnect system. Refer to “uconnect settings/customer programmable features” in “understanding your instru- ment panel” for further information. Blind spot alert lights only when operating in blind spot alert mode, the bsm s...

  • Page 146

    Note: the bsm system will store the current operating mode when the vehicle is shut off. Each time the vehicle is started the previously stored mode will be recalled and used. General information this vehicle has systems that operate on radio frequency that comply with part 15 of the federal communi...

  • Page 147

    Power seats — if equipped some models may be equipped with eight-way power driver and front passenger seats. The power seat switches are located on the outboard side of the seat. There are two switches that control the movement of the seat cushion and the seatback. Adjusting the seat forward or rear...

  • Page 148

    Move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch...

  • Page 149

    Caution! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power lumbar — if equipped vehicles equipped with power driver or passenger seat...

  • Page 150

    While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! •...

  • Page 151

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Front passenger seat fold-flat feature — if equipped to fold the seatback to the flat ...

  • Page 152

    Caution! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Warning! • adjusting a seat while the vehicle is moving is dangerous. The sudden...

  • Page 153

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 154

    Note: • once a heat setting is selected, heat will be felt within two to five minutes. • the engine must be running for the heated seats to operate. Vehicles equipped with remote start on models that are equipped with remote start, the heated seats can be programmed to come on during a remote start....

  • Page 155

    Rear heated seats — if equipped on some models, the two rear outboard seats may be equipped with heated seats. There are two heated seat switches that allow the rear passengers to operate the seats independently. The heated seat switches for each heater are located on the rear of the center console....

  • Page 156

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 157

    Note: the engine must be running for the ventilated seats to operate. Vehicles equipped with remote start on models that are equipped with remote start, the ventilated seats can be programmed to come on during a remote start. This feature can be programmed through the uconnect system. Refer to “ucon...

  • Page 158

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to reduce the gap between the back of the occupant’s head and the ahr. This system is design to reduce the risk of injury to the driver or front passenger in certain types of rear impacts. Refer to “occupant ...

  • Page 159

    For comfort the active head restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Note: • the head ...

  • Page 160

    • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head restraints (ahr)” in “things to know before starting your vehicle” for further information. Warning! • all occupants, including the driver, should not operate a vehicle or sit in a vehicle...

  • Page 161

    The center head restraint has limited adjustment. Lift upward on the head restraint to raise it, or push down- ward on the head restraint to lower it. Warning! Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure t...

  • Page 162

    Note: be sure that the front seats are fully upright and positioned forward. This will allow the rear seatback to fold down easily. 1. Pull upward on the release lever to release the seat. Note: • do not fold the 60% rear seat down with the left outboard or rear center seat belt buckled. • do not fo...

  • Page 163

    To raise rear seat raise the rear seatback and lock it into place. If interfer- ence from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Warning! • be certain that the seatback is securely locked into position. If the seat...

  • Page 164

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Driver memory seat — if equipped this feature allows the driver to store up to two dif...

  • Page 165

    • the (1) and (2) buttons which are used to recall either of two pre-programmed memory profiles. Programming the memory feature note: to create a new memory profile, perform the following: 1. Cycle the vehicles ignition to the on/run position (do not start the engine). 2. Adjust all memory profile s...

  • Page 166

    Note: • memory profiles can be set without the vehicle in park, but the vehicle must be in park to recall a memory profile. • to set a memory profile to your rke transmitter, refer to “linking and unlinking the remote keyless entry transmitter to memory” in this section. Linking and unlinking the re...

  • Page 167

    Note: your rke transmitters can be unlinked to your memory settings by pushing the set (s) button, and within 10 seconds, followed by pushing the unlock button on the rke transmitter. Memory position recall note: the vehicle must be in park to recall memory positions. If a recall is attempted when t...

  • Page 168

    Easy entry/exit seat this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. The distance the driver seat moves depends on where you have the driver seat positioned when you cycle the vehicle’s ignition to the off position. • when you...

  • Page 169

    To open and close the hood to open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door. 2. Reach under the hood, move safety latch to the left and lift the hood. Hood release safety latch location 3 understanding the ...

  • Page 170

    Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle...

  • Page 171

    To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on, the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the o (off) position. Note: • your ve...

  • Page 172

    Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to the a (auto) position. When the system is on, the headlight delay feature is also on. This means the headlights will st...

  • Page 173

    Detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. Note: • the automatic high beam headlamp control can be turned on or off using the uconnect system. Refer to “uconnect settings” in “understanding your instru- ment pa...

  • Page 174

    Note: • if a turn signal is activated, the drl lamp on the same side of the vehicle will turn off for the duration of the turn signal activation. Once the turn signal is no longer active, the drl lamp will illuminate. • the drl function may be disabled through the uconnect system. Refer to “uconnect...

  • Page 175

    Parking lights and panel lights to turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the o (off) position. Fog lights — if equipped the fog lights are turned on by rotating the headlight ...

  • Page 176

    Interior lights courtesy and dome lights are turned on when the front doors are opened or when the dimmer control (rotating wheel on the right side of the headlight switch) is rotated to its farthest upward position. If your vehicle is equipped with remote keyless entry (rke) and the unlock button i...

  • Page 177

    Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is opened. Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. I...

  • Page 178

    Second time. The lights will also turn on when the unlock button on the remote keyless entry (rke) is pushed. Courtesy lights the courtesy lights can be turned on by pushing the top corner of the lens. To turn the lights off, push the lens a second time. Front map/reading light switches courtesy lig...

  • Page 179

    Ambient light — if equipped the overhead console is equipped with an ambient light feature. This light casts illumination for improved visibil- ity of the floor and center console area. Multifunction lever the multifunction lever is located on the left side of the steering column. Ambient light mult...

  • Page 180

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside l...

  • Page 181

    Windshield wipers and washers the windshield wiper/washer controls are located on the multifunction lever on the left side of the steering col- umn. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “rear window fe...

  • Page 182

    Caution! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Intermittent wiper system use one of the...

  • Page 183

    Lever is pushed while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the end of the lever is released, and then resume the intermittent interval previously selected. If the end of the lever is pushed while the wipers are in the off position, the wipers...

  • Page 184

    Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Rain sensing wipers — if equipped this feature senses moisture on the windshield and automaticall...

  • Page 185

    Note: • the rain sensing feature will not operate when the wiper switch is in the low or high-speed position. • the rain sensing feature may not function properly when ice, or dried salt water is present on the wind- shield. • use of rain-x or products containing wax or silicone may reduce rain sens...

  • Page 186

    Headlight washers — if equipped the multifunction lever operates the headlight washers when the ignition switch is in the on position and the headlights are turned on. The multifunction lever is located on the left side of the steering column. To use the headlight washers, push the multifunction lev...

  • Page 187

    To unlock the steering column, push the lever downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in posi...

  • Page 188

    To tilt the steering column, move the lever up or down as desired. To lengthen or shorten the steering column, pull the lever toward you or push the lever away from you as desired. Note: for vehicles equipped with driver memory seat, you can use your remote keyless entry (rke) transmit- ter or the m...

  • Page 189

    Heated steering wheel — if equipped the steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate for up to 80 minutes before automatically shutti...

  • Page 190

    Warning! (continued) • do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. Electronic speed control — if equipped when engaged, the electronic speed control...

  • Page 191

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 192

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate the electronic speed control with- out erasing the set speed from memory. Pushing the on/off button or turning the ignition switch off erases the set speed from ...

  • Page 193

    • if the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed will be established. To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set - button. The drivers preferred units can b...

  • Page 194

    Note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without electronic speed control. Warning! Electronic speed control can be dangerous...

  • Page 195

    • if the acc sensor detects a vehicle ahead, acc will apply limited braking or acceleration (not to exceed the original set speed) automatically to maintain a preset following distance, while matching the speed of the vehicle ahead. The cruise control system has two control modes: • adaptive cruise ...

  • Page 196

    Warning! (continued) • the acc system: • does not react to pedestrians, oncoming vehicles, and stationary objects (e.G., a stopped vehicle in a traffic jam or a disabled vehicle). • cannot take street, traffic, and weather condi- tions into account, and may be limited upon adverse sight distance con...

  • Page 197

    Note: any chassis/suspension or tire size modifications to the vehicle will effect the performance of the adaptive cruise control and forward collision warning system. Activating adaptive cruise control (acc) you can only engage acc if the vehicle speed is above 0 mph (0 km/h). The minimum set speed...

  • Page 198

    • when you apply the brakes. • when the parking brake is set. • when the automatic transmission is in park, re- verse or neutral. • when the vehicle speed is outside of the speed range. • when the brakes are overheated. • when the driver door is open. • when the driver seat belt is unbuckled. To act...

  • Page 199

    Warning! Leaving the adaptive cruise control (acc) system on when not in use is dangerous. You could acciden- tally set the system or cause it to go faster than you (continued) warning! (continued) want. You could lose control and have a collision. Always leave the system off when you are not using ...

  • Page 200

    Remove your foot from the accelerator pedal. If you do not, the vehicle may continue to accelerate beyond the set speed. If this occurs: • the message “driver override” will display in the did. • the system will not be controlling the distance be- tween your vehicle and the vehicle ahead. The vehicl...

  • Page 201

    • the ignition is turned off. • you switch to four-wheel drive low. To resume if there is a set speed in memory push the res (resume) button and then remove your foot from the accelerator pedal. The did will display the last set speed. Note: • if your vehicle stays at standstill for longer than two ...

  • Page 202

    The speed increment shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pushing the set + button once will result in a 1 mph increase in set speed. Each subsequent tap of the button results in an increase of 1 mph. • if the button is continually pushed, the...

  • Page 203

    • if the button is continually pushed, the set speed will continue to decrease in 5 mph decrements until the button is released. The decrease in set speed is re- flected in the did. Metric speed (km/h) • pushing the set - button once will result in a 1 km/h decrease in set speed. Each subsequent tap...

  • Page 204

    Setting the following distance in acc the specified following distance for acc can be set by varying the distance setting between four bars (longest), three bars (long), two bars (medium) and one bar (short). Using this distance setting and the vehicle speed, acc calculates and sets the distance to ...

  • Page 205

    Distance setting 3 bars (long) distance setting 2 bars (medium) 3 understanding the features of your vehicle 203.

  • Page 206

    To increase the distance setting, push the distance setting — increase button and release. Each time the button is pushed, the distance setting increases by one bar (longer). To decrease the distance setting, push the distance set- ting — decrease button and release. Each time the button is pushed, ...

  • Page 207

    • the system disengages. (refer to the information on acc activation). The maximum braking applied by acc is limited; how- ever, the driver can always apply the brakes manually, if necessary. Note: the brake lights will illuminate whenever the acc system applies the brakes. A proximity warning will ...

  • Page 208

    Overtake aid when driving with acc engaged and following a ve- hicle, the system will provide an additional acceleration up to the acc set speed to assist in passing the vehicle. This additional acceleration is triggered when the driver utilizes the left turn signal and will only be active when pass...

  • Page 209

    Adaptive cruise control (acc) menu the did displays the current acc system settings. The did is located in the center of the instrument cluster. The information it displays depends on acc system status. Push the adaptive cruise control (acc) on/ off button (located on the steering wheel) until one o...

  • Page 210

    Display warnings and maintenance “wipe front radar sensor in front of vehicle” warning the “acc/fcw unavailable wipe front radar sensor” warning will display and also a chime will indicate when conditions temporarily limit system performance. This most often occurs at times of poor visibility, such ...

  • Page 211

    • do not remove any screws from the sensor. Doing so could cause an acc system malfunction or failure and require a sensor realignment. • if the sensor or front end of the vehicle is damaged due to a collision, see your authorized dealer for service. • do not attach or install any accessories near t...

  • Page 212

    Obstructions, such as mud, dirt, or ice on windshield and fog on the inside of glass. In these cases, the did will display “acc/fcw limited functionality clean front windshield” and the system will have degraded perfor- mance. The “acc/fcw limited functionality clean front windshield” message can so...

  • Page 213

    Precautions while driving with acc in certain driving situations, acc may have detection issues. In these cases, acc may brake late or unexpect- edly. The driver needs to stay alert and may need to intervene. Towing a trailer towing a trailer is not advised when using acc. Offset driving acc may not...

  • Page 214

    The vehicle is out of the curve the system will resume your original set speed. This is a part of normal acc system functionality. Note: on tight turns acc performance may be limited. Using acc on hills when driving on hills, acc may not detect a vehicle in your lane. Depending on the speed, vehicle...

  • Page 215

    Lane changing acc may not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, acc has not yet detected the vehicle changing lanes and it may not detect the vehicle until it’s too late for the acc system to take action. Acc may not detect a vehic...

  • Page 216

    Narrow vehicles some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead. Stationary objects and vehicles acc does not react to stationary objects and ...

  • Page 217

    General information this vehicle has systems that operate on radio frequency that comply with part 15 of the federal communications commission (fcc) rules and with industry canada standards rss- gen/210/220/310. Operation is subject to the following two conditions: 1. The device may not cause harmfu...

  • Page 218

    Warning! In the normal cruise control mode, the system will not react to vehicles ahead. In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to vehicle distance is ...

  • Page 219

    U.S. Speed (mph) • pushing the set + button once will result in a 1 mph increase in set speed. Each subsequent tap of the button results in an increase of 1 mph. • if the button is continually pushed, the set speed will continue to increase in 5 mph increments until the button is released. The incre...

  • Page 220

    Metric speed (km/h) • pushing the set - button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a decrease of 1 km/h. • if the button is continually pushed, the set speed will continue to decrease in 10 km/h decrements until the button is released. The...

  • Page 221

    • you engage four-wheel drive low. • the adaptive cruise control (acc) on/off button is pushed. Forward collision warning (fcw) with mitigation — if equipped forward collision warning (fcw) with mitigation operation the forward collision warning (fcw) system with mitigation provides the driver with ...

  • Page 222

    Warning with mitigation event stops the vehicle com- pletely, the system will hold the vehicle at a standstill for two seconds and then release the brakes. When the system determines a collision with the vehicle in front of you is no longer probable, the warning message will be deactivated. Note: • ...

  • Page 223

    Warning! Forward collision warning (fcw) is not intended to avoid a collision on its own, nor can fcw detect every type of potential collision. The driver has the responsibility to avoid a collision by controlling the vehicle via braking and steering. Failure to follow this warning could lead to ser...

  • Page 224

    System to warn the driver of a possible collision with the vehicle in front using audible/visual warnings and it applies autonomous braking. Changing the fcw status to “far” setting allows the system to warn the driver of a possible collision with the vehicle in front using audible/visual warning wh...

  • Page 225

    Fcw limited warning if the did displays “acc/fcw limited functionality” or “acc/fcw limited functionality clean front wind- shield” momentarily, there may be a condition that limits fcw functionality. Although the vehicle is still drivable under normal conditions, the active braking may not be fully...

  • Page 226

    • automatic brakes will not be available if there is a faulted condition detected with the parksense park assist system or the braking system module. • the automatic braking function may only be applied if the vehicle deceleration is not enough to avoid collid- ing with a detected obstacle. • the au...

  • Page 227

    Parksense can be active only when the shift lever/gear selector is in reverse. If parksense is enabled at this shift lever/gear selector position, the system will remain active until the vehicle speed is increased to approxi- mately 7 mph (11 km/h) or above. When in reverse and above the system’s op...

  • Page 228

    The system will indicate a detected obstacle by showing a single arc in the left and/or right rear regions based on the obstacle’s distance and location relative to the vehicle. If an obstacle is detected in the left and/or right rear region, the display will show a single arc in the left and/or rig...

  • Page 229

    Slow tone slow tone 3 understanding the features of your vehicle 227.

  • Page 230

    Fast tone fast tone 228 understanding the features of your vehicle.

  • Page 231

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: continuous tone 3 understanding the features of your vehicle 229.

  • Page 232

    Warning alerts rear dis- tance (in/cm) greater than 79 in (200 cm) 79-59 in (150-100 cm) 59-47 in (150-120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none single 1/2 second tone slow slow fast fast continuous arcs-left none none non...

  • Page 233

    Note: parksense will reduce the volume of the radio, if on, when the system is sounding an audio tone. Adjustable chime volume settings rear chime volume settings can be selected from the customer-programmable features section of the uconnect system, refer to “uconnect settings” in “un- derstanding ...

  • Page 234

    Switch is pushed, and the system requires service, the parksense switch led will blink momentarily, and then the led will be on. Service the parksense rear park assist system during vehicle start up, when the parksense rear park assist system has detected a faulted condition, the instrument cluster ...

  • Page 235

    Parksense system usage precautions note: • ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep the parksense system operating properly. • jackhammers, large trucks, and other vibrations could affect the performance of parksense. • when you turn parksense off, the instrumen...

  • Page 236

    • parksense should be disabled when the liftgate is in the open position and the vehicle is in reverse. An open liftgate could provide a false indication that an obstacle is behind the vehicle. Caution! • parksense is only a parking aid and it is unable to recognize every obstacle, including small o...

  • Page 237

    Warning! (continued) could detect the ball mount and hitch ball assem- bly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle. Parksense front and rear park assist — if equipped the parksense park assist system provides visual and audible indications o...

  • Page 238

    • the automatic braking function can be enabled/ disabled from the customer-programmable features section of the uconnect system. • parksense will retain its last known configuration state for the automatic braking function through ignition cycles. The automatic braking function is intended to assis...

  • Page 239

    Parksense sensors the four parksense sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 in (30 cm) up to 79 in (200 cm) from the rear fascia/bumper in the horizontal direct...

  • Page 240

    The system will indicate a detected obstacle by showing a single arc in the left and/or right rear regions based on the object’s distance and location relative to the vehicle. If an object is detected in the left and/or right rear region, the display will show a single arc in the left and/or right r...

  • Page 241

    Slow tone slow tone for rear only 3 understanding the features of your vehicle 239.

  • Page 242

    Fast tone for rear only fast tone 240 understanding the features of your vehicle.

  • Page 243

    The vehicle is close to the obstacle when the did display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: continuous tone 3 understanding the features of your vehicle 241.

  • Page 244

    Warning alerts for rear rear dis- tance (in/cm) greater than 79 in (200 cm) 79-59 in (150-100 cm) 59-47 in (150-120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none single 1/2 second tone slow slow fast fast continuous arcs-left none...

  • Page 245

    Warning alerts for front front distance (in/cm) greater than 47 in (120 cm) 47-39 in (120-100 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) less than 12 in (30 cm) audible alert chime none none none fast continuous arcs-left none none none 2nd flashing 1st flashing arcs-center none 4th solid 3rd flas...

  • Page 246

    Parksense will retain its last known configuration state through ignition cycles. Enabling and disabling parksense parksense can be enabled and disabled with the parksense switch. When the parksense switch is pushed to dis- able the system, the instrument cluster will display the “parksense off” mes...

  • Page 247

    Graphic will be displayed with ⬙unavailable⬙ at ei- ther the front or rear sensor location depending on where the fault is detected. The system will continue to provide arc alerts for the side that is functioning properly. These arc alerts will interrupt the ⬙parksense unavail- able wipe rear sensor...

  • Page 248

    • jackhammers, large trucks, and other vibrations could affect the performance of parksense. • when you turn parksense off, the instrument cluster will display “parksense off.” furthermore, once you turn parksense off, it remains off until you turn it on again, even if you cycle the ignition. • when...

  • Page 249

    Caution! • parksense is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • the vehicle mu...

  • Page 250

    Parkview rear back up camera — if equipped your vehicle may be equipped with the parkview rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever/gear selector is put into reverse. The image will be displayed on the navigation/m...

  • Page 251

    Zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 6.5 ft (30 cm - 2 m) green 6.5 ft or greater (2 m or greater) warning! Drivers must be careful when backing up even when using the parkview rear back up camera. Always check carefully behind your vehicle, and be sure to ...

  • Page 252

    Note: if snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Overhead console the overhead console contains courtesy/reading lights and storage for sunglasses. Universal garage door opener (homelin...

  • Page 253

    Front map/reading lights — if equipped lights are mounted in the overhead console. Each light can be turned on by pushing the switch on either side of the console. These buttons are backlit for night time visibility. To turn the lights off, push the switch a second time. The lights also turn on when...

  • Page 254

    Courtesy lights the courtesy lights can be turned on by pushing the top corner of the lens. To turn the lights off, push the lens a second time. Sunglasses bin door at the front of the console a compartment is provided for the storage of a pair of sunglasses. The storage compart- ment access is a “p...

  • Page 255

    Garage door opener — if equipped homelink replaces up to three hand-held transmitters that operate devices such as garage door openers, motor- ized gates, lighting or home security systems. The homelink unit is powered by your vehicles 12 volt battery. The homelink buttons, located on the overhead c...

  • Page 256

    Before you begin programming homelink be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the de...

  • Page 257

    1. Place the ignition in the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink button you wish to program while keeping the homelink indicator light in view. 3. Push and hold the homelink button you want to program while you push and hold the hand-h...

  • Page 258

    Firmly push and release the “learn” or “train- ing” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the learn/train mode. Note: you have 30 seconds in which to initiate the next step after the learn button has been pushed. 6. Retu...

  • Page 259

    2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink button you wish to program while keeping the homelink indicator light in view. 3. Push and hold the homelink button you want to program while you push and hold the hand-held transmitter button. 4. Continue to hold bo...

  • Page 260

    Canadian/gate operator programming for programming transmitters in canada/united states that require the transmitter signals to “time-out” after several seconds of transmission. Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission ...

  • Page 261

    Note: • if the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the homelink button is pushed. • to program the two remaining homelink buttons, repeat each step for each remaining button. Do not erase the channels. If you unplugged the ga...

  • Page 262

    To do this, push and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The homelink universal transceiver is disabled when the vehicle security alarm is active. Troubleshooting tips if you are hav...

  • Page 263

    Warning! (continued) after 1982. Do not use a garage door opener without these safety features. Call toll-free 1-800-355-3515 or, on the internet at homelink.Com for safety information or assistance. General information this device complies with part 15 of the fcc rules and with industry canada lice...

  • Page 264

    Warning! • never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with keyless enter-n-go in the acc or on/run mode. Occupants, parti...

  • Page 265

    Movement. The sunroof and sunshade will remain in a partially opened condition until the sunroof switch is pushed again. Closing sunroof — express press the switch forward and release it within one-half second and the sunroof will close automatically from any position. The sunroof will close fully a...

  • Page 266

    Sunshade operation the sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Note: the sunshade cannot be closed if the sunroof is open. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound ...

  • Page 267

    Relearn procedure for vehicles equipped with a single-pane sunroof, there is a relearn procedure that allows you to calibrate the sunroof when the “auto up” feature stops working. To reset the sunroof, follow these steps: 1. Set the ignition to the acc on/run position. 2. Ensure that the sunroof is ...

  • Page 268

    Warning! • never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location (continued) warning! (continued) accessible to children. Do not leave the ignition of a vehicle equipped with keyless enter-n-go in the acc...

  • Page 269

    Opening sunroof — express push the switch rearward and release it within one-half second. The sunroof and sunshade will open automati- cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “express open.” during express open operation, any other act...

  • Page 270

    The shade will open automatically to the full-open posi- tion. This is called “express open”. During express open operation, any movement of the shade switch will stop the shade. Opening power shade — manual mode to open the shade, push and hold the switch rearward. The shade will open and stop auto...

  • Page 271

    Note: if the sunshade is in the closed position when the vent switch is pushed, the sunshade will automatically cycle to the halfway open position prior to the sunroof opening to the vent position. Pinch protect feature this feature will detect an obstruction in the opening of the sunroof during exp...

  • Page 272

    • this feature is programmable using the uconnect system. Refer to “uconnect settings” in “understand- ing your instrument panel” for further information. Electrical power outlets your vehicle is equipped with 12 volt (13 amp) power outlets that can be used to power cellular phones, small electronic...

  • Page 273

    The front power outlet is located inside the storage area on the center stack of the instrument panel. Push inward on the storage lid to open the compartment and gain access to this power outlet. In addition to the front power outlet, there is also a power outlet located in the storage area of the c...

  • Page 274

    The rear power outlet is located in the right rear cargo area. Note: the rear power outlet can be switched from switched “ignition” only to constant “battery” powered all the time. See your local authorized dealer for details. Rear power outlet power outlet right rear quarter panel fuse 272 understa...

  • Page 275

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 276

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 277

    The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. To avoid overloading the circuit, chec...

  • Page 278

    Cupholders there are two cupholders for the front seat passengers located in the center console. There are two cupholders for the rear seat passengers located in the fold-down center armrest. Front cupholders rear cupholders 276 understanding the features of your vehicle.

  • Page 279

    Storage glove compartment the glove compartment is located on the right side of the instrument panel. To open the glove compartment, pull outward on the latch and lower the glove compartment door. Glove compartment opened glove compartment 3 understanding the features of your vehicle 277.

  • Page 280

    Door storage large storage areas are built into the door panels for easy access. Console features the center console contains both an upper and a lower storage area. Door panel storage storage compartment 278 understanding the features of your vehicle.

  • Page 281

    To open the upper storage compartment, pull upward on the small latch located on the lid. Lift upward on the larger of the latches to access the lower storage compartment. Storage compartment latches lower storage compartment 3 understanding the features of your vehicle 279.

  • Page 282

    Your vehicle may have an optional cd or dvd player located in the center console. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Cargo area features rechargeable flashlight...

  • Page 283

    To operate the flashlight, push the switch once for high, twice for low, and a third time to return to off. Cargo storage bins there are up to four removable storage bins located in the rear cargo area. There are two storage bins located on either side of the cargo area. Push and release three-push ...

  • Page 284

    Note: if your vehicle is equipped with a rear sub- woofer, the passenger side cargo area will not be avail- able. Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether hook (attached to the bottom of the load floor)...

  • Page 285

    Retractable cargo area cover — if equipped note: the purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the...

  • Page 286

    Warning! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. D...

  • Page 287

    Warning! • to help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. • cargo tie-down hooks are not safe anchors for a child seat t...

  • Page 288

    Warning! (continued) the weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting in per- sonal injury, follow these guidelines for loading your vehicle: • do not carry loads which exceed the load limits described o...

  • Page 289

    Rotate the center portion of the lever upward to the first detent for intermittent operation and to the second detent for continuous rear wiper operation. Rotating the center portion upward once more will activate the washer pump which will con- tinue to operate as long as the switch is held. Upon r...

  • Page 290

    Mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ap- proximately 10 minutes. For an additional five minutes of operation, push the button a second time. Note: to prevent excessive battery d...

  • Page 291

    Inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. To move the crossbars, loosen the attachments, located at the upper edge of each crossbar, approximately eight turns using the anti-theft wrench provided with the mopar crossbars. Then, move the cros...

  • Page 292

    Caution! (continued) • to avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lb (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropri- ately. • long loads which extend over the windshield, such as wood panels or sur...

  • Page 293

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .295 䡵 instrument cluster — premium . . . . . .296 䡵 warning and indicator lights . . . . . . .298 ▫ red telltale indicator lights . . . . . . . . . . . . . .299 ▫ yellow telltale indicator lights . . . . . . ...

  • Page 294

    ▫ customer programmable features — uconnect 8.4 settings . . . . . . . . . . . . . . . . . . .367 䡵 uconnect radios — if equipped . . . . . .388 䡵 ipod/usb/mp3 control — if equipped . . .388 䡵 uconnect multimedia — video entertainment system (ves) — if equipped . . . . . . . . . . . . . . . . . . . ...

  • Page 295

    ▫ radio operation . . . . . . . . . . . . . . . . . . . . . .427 ▫ cd player. . . . . . . . . . . . . . . . . . . . . . . . . . .427 䡵 cd/dvd disc maintenance . . . . . . . . . . .427 䡵 radio operation and mobile phones . .428 ▫ regulatory and safety information . . . . . . . . .428 䡵 climate contro...

  • Page 296

    ▫ voice texting (8.4a/8.4an) . . . . . . . . . . . . . .457 ▫ yelp (8.4a/8.4an). . . . . . . . . . . . . . . . . . . . .459 ▫ siriusxm travel link (8.4a/8.4an). . . . . . . . .460 ▫ siri eyes free — if equipped . . . . . . . . . . . . .461 ▫ do not disturb . . . . . . . . . . . . . . . . . . . . . ....

  • Page 297

    Instrument panel features 1 — air outlet 6 — lower switch bank 11 — hood release 2 — instrument cluster 7 — hazard switch 12 — fuel door release 3 — radio 8 — storage bin (sd card, aux, usb media hub) 13 — headlight switch 4 — glove compartment 9 — esc button 14 — dimmer control 5 — climate controls...

  • Page 298

    Instrument cluster — premium premium did instrument cluster 296 understanding your instrument panel.

  • Page 299

    1. Tachometer • indicates the engine speed in revolutions per minute (rpm x 1000). 2. Driver information display (did) • the driver information display (did) features a driver-interactive display. Refer to “driver informa- tion display (did)” in “understanding your instru- ment panel” for further in...

  • Page 300

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “maintaining your vehicle”. Follow the warnings unde...

  • Page 301

    Red telltale indicator lights seat belt reminder warning light red telltale light what it means seat belt reminder warning light when the ignition switch is first turned to on/run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is ...

  • Page 302

    Air bag warning light red telltale light what it means air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during startup, stays on, or turns on while driving, have the system inspec...

  • Page 303

    Brake warning light red telltale light what it means united states canada brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid le...

  • Page 304

    The light will remain on until the cause is corrected. Note: the light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces...

  • Page 305

    Vehicle security warning light — if equipped red telltale light what it means vehicle security warning light — if equipped this light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. Oil pressu...

  • Page 306

    Engine temperature warning light red warning light what it means engine temperature warning light this light warns of an overheated engine condition. As engine coolant temperatures rise and the gauge approaches h, this indicator will illuminate and a single chime will sound after reaching a set thre...

  • Page 307

    Oil temperature warning light red telltale light what it means oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. 4 understanding your instrument panel 305.

  • Page 308

    Charging system warning light red telltale light what it means charging system warning light this light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s nonessential electrical devices or increase engine speed (if at ...

  • Page 309

    Electronic throttle control (etc) warning light red telltale light what it means electronic throttle control (etc) warning light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected while the engine is running, the light will either stay on ...

  • Page 310

    Electric power steering fail warning — if equipped red telltale light what it means electric power steering fail warning — if equipped this light is used to manage the electrical warning of the eps (power steering system). Re- fer to “power steering” in “starting and operating” for further informati...

  • Page 311

    Liftgate open warning light red telltale light what it means liftgate open warning light this indicator will turn when the liftgate is open. Note: if the vehicle is moving, there will also be a single chime. Transmission temperature warning light red telltale light what it means transmission tempera...

  • Page 312

    Caution! Continuous driving with the transmission tempera- ture warning light illuminated will eventually cause severe transmission damage or transmission failure. Warning! If you continue operating the vehicle when the transmission temperature warning light is illumi- nated you could cause the flui...

  • Page 313

    Yellow telltale indicator lights engine check/malfunction indicator light (mil) yellow telltale light what it means engine check/malfunction indicator light (mil) the engine check/malfunction indicator light (mil) is a part of an onboard diagnostic system called obd ii that monitors engine and autom...

  • Page 314

    Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warni...

  • Page 315

    Electronic stability control (esc) indicator light — if equipped yellow telltale light what it means electronic stability control (esc) indicator light — if equipped the “esc indicator light” in the instrument cluster will come on when the ignition switch is turned to the on/run position. It should ...

  • Page 316

    Electronic stability control (esc) off indicator light — if equipped yellow telltale light what it means electronic stability control (esc) off indicator light — if equipped this light indicates the electronic stability control (esc) is off. Tire pressure monitoring indicator light yellow telltale l...

  • Page 317

    Important: do not continue driving with one or more flat tires as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. Repair immediately using the dedicated tire repair kit and contact your authorized dealership as soon as possible. Each tire, including the spare (if ...

  • Page 318

    Illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur for a variety of reasons, includi...

  • Page 319

    Anti-lock brake (abs) indicator light yellow telltale light what it means anti-lock brake (abs) indicator light this light monitors the anti-lock brake system (abs). The light will turn on when the igni- tion switch is placed in the on/run position and may stay on for as long as four seconds. If the...

  • Page 320

    Loose fuel filler cap indicator light — if equipped yellow telltale light what it means loose fuel filler cap indicator light — if equipped this light will illuminate when fuel filler cap is loose. Properly close the filler cap to disen- gage the light. If the light does not turn off, please see you...

  • Page 321

    Service stop/start system indicator light — if equipped yellow telltale light what it means service stop/start system indicator light — if equipped this telltale will turn on to indicate the stop/start system is not functioning properly and service is required. Forward collision indicator light — if...

  • Page 322

    Forward collision warning off indicator light — if equipped yellow telltale light what it means forward collision off indicator light — if equipped this light indicates the forward collision warning is off. Low washer fluid indicator light — if equipped yellow telltale light what it means low washer...

  • Page 323

    Adaptive cruise control alert indicator light — if equipped yellow telltale light what it means adaptive cruise control alert indicator light this light will turn on when the acc is not operating and needs service. For further infor- mation, refer to “adaptive cruise control (acc)” in “understanding...

  • Page 324

    4wd low indicator light — if equipped yellow telltale light what it means 4wd low indicator light this light alerts the driver that the vehicle is in the four-wheel drive low mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same...

  • Page 325

    Air suspension light — if equipped yellow telltale light what it means air suspension light this light will illuminate when the air suspension system is activated. 4 understanding your instrument panel 323.

  • Page 326

    Green telltale indicator lights park/headlight on indicator light green telltale light what it means park/headlight on indicator light this indicator will illuminate when the park lights or headlights are turned on. 324 understanding your instrument panel.

  • Page 327

    Front fog indicator light — if equipped green telltale light what it means front fog indicator light — if equipped this indicator will illuminate when the front fog lights are on. 4 understanding your instrument panel 325.

  • Page 328

    Turn signal indicator lights green tell- tale light what it means turn signal indicator lights the instrument cluster directional arrow will flash independently for the left or right turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multifunct...

  • Page 329

    Stop/start active indicator light — if equipped green telltale light what it means stop/start active indicator light — if equipped this telltale will illuminate when the stop/start function is in “autostop” mode. Cruise control engaged indicator light green telltale light what it means cruise contro...

  • Page 330

    Adaptive cruise control (acc) distance setting display light — if equipped green telltale light what it means adaptive cruise control (acc) distance setting display light this will display the distance setting for the acc system. Refer to “adaptive cruise control (acc)” in “understanding the feature...

  • Page 331

    Blue telltale indicator light high beam indicator light blue telltale light what it means high beam indicator light this indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch...

  • Page 332

    White telltale indicator light electronic speed control on indicator light white telltale light what it means electronic speed control on indicator light this light will turn on when the electronic speed control is on. 330 understanding your instrument panel.

  • Page 333

    Adaptive cruise control (acc) on light — if equipped white telltale light what it means adaptive cruise control (acc) on light this light will turn on when the adaptive cruise control is on. Refer to “adaptive cruise control (acc)” in “understanding the features of your vehicle” for further informat...

  • Page 334

    Selec speed control indicator light — if equipped white telltale light what it means selec speed control indicator light this light will turn on when “selec speed control” is activated. To activate “selec speed control”, assure the vehicle is four wheel drive low (4wd) and push the button on the ins...

  • Page 335

    Driver information display (did) the driver information display (did) features a driver- interactive display that is located in the instrument cluster. The did menu items consists of the following: • speedometer main gauge • vehicle info • terrain — if equipped • driver assist — if equipped • fuel e...

  • Page 336

    The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: • up arrow button push and release the up arrow button to scroll upward through the main menu and submenus. • down arrow button push and release the down arrow button to scroll downward...

  • Page 337

    • ok button the ok button may be used for the following: selection reset (hold) clearing (push) did displays the did displays are located in the center portion of the cluster and consist of multiple sections: 1. Main screen — the inner ring of the display will illuminate in grey under normal conditi...

  • Page 338

    • five second stored messages when the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns to the previous screen. Most of the messages of this type are then stored (as long as the condition that activated it remains active) and...

  • Page 339

    Is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style. Unless reset, this message will continue to display each time you cycle the ignition to the on/run position. To turn off the message temporarily, push and release the ok button....

  • Page 340

    Did messages includes the following, but not limited to: • front seatbelts unbuckled • driver seat belt unbuckled • passenger seat belt unbuckled • traction control off • washer fluid low • oil pressure low • oil change due • fuel low • service anti-lock brake system • service electronic throttle co...

  • Page 341

    • lights on • right front turn signal light out • right rear turn signal light out • left front turn signal light out • left rear turn signal light out • ignition or accessory on • vehicle not in park • remote start active push start button • remote start canceled fuel low • remote start canceled to...

  • Page 342

    • service shifter • service air suspension system • normal ride height achieved • aerodynamic ride height achieved • off road 1 ride height achieved • off road 2 ride height achieved • entry/exit ride height achieved • selected ride height not permitted • service air suspension system immediately • ...

  • Page 343

    Vehicle info (customer information features) push and release the up or down ar- row button until the vehicle info icon/title is highlighted in the did. Push and release the left or right arrow button to scroll through the information submenus and push and release the ok button to select or reset th...

  • Page 344

    Fuel economy push and release the up or down ar- row button until the fuel economy menu icon/title is highlighted. Push and hold the ok button to reset feature. Push the left or right arrow button to select the different fuel economy sections. The fuel economy screen may be on the same screen as the...

  • Page 345

    Stop/start — if equipped push and release the up or down ar- row button until the stop/start icon/title is highlighted in the did. The screen will dis- play the stop/start status. Audio push and release the up or down ar- row button until the audio menu icon/title is highlighted in the did. Navigati...

  • Page 346

    Speed warning — if equipped push and release the up or down ar- row button until the speed warning menu icon/title is highlighted in the did. Push and release the ok button to enter speed warning. Use the up or down arrow button to select a desired speed, then push and release the ok button to set t...

  • Page 347

    • fuel economy current • trip a • trip b upper right • none • compass • outside temp (default setting) • time • range to empty (rte) • fuel economy average • fuel economy current • trip a • trip b defaults (restores all settings to default settings) • cancel • restore favorite menus — equipped • spe...

  • Page 348

    • screen setup • speed warning the menu with (show/hide) means user can press ok button to choose show or hide this menu on the did display. Cybersecurity your vehicle may be a connected vehicle and may be equipped with both wired and wireless networks. These networks allow your vehicle to send and ...

  • Page 349

    Warning! (continued) • only insert media (e.G., usb, sd card, or cd) into your vehicle if it came from a trusted source. Media of unknown origin could possibly contain mali- cious software, and if installed in your vehicle, it may increase the possibility for vehicle systems to be breached. • as alw...

  • Page 350

    Uconnect settings the uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allow you to access and change the customer programmable features. Many features can vary by vehicle. Uconnect 5.0 buttons on touchsc...

  • Page 351

    Buttons on the faceplate buttons on the faceplate are located below the uconnect system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side of the climate controls in the center of the instru- ment panel. Turn the control knob to scroll ...

  • Page 352

    Buttons on the touchscreen buttons on the touchscreen are accessible on the uconnect display. Customer programmable features — uconnect 5.0 personal settings push the more button on the faceplate to display the menu setting screen. In this mode the uconnect system allows you to access programmable f...

  • Page 353

    And release the “auto” or “manual” button on the touchscreen. Then press the arrow back button on the touchscreen. Note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the display brightness day control even though the headli...

  • Page 354

    • touchscreen beep when in this display, you may turn on or shut off the sound heard when a button on the touchscreen is pressed. Press the “touchscreen beep” button on the touchscreen then select from “on” or “off.” units after pressing the “units” button on the touchscreen you may select each unit...

  • Page 355

    • show command list when in this display, you may change the show com- mand list settings. To change the show command list settings, press the “show command list” button on the touchscreen and select from “always,” “with help” or “never.” clock & date after pressing the “clock & date” button on the ...

  • Page 356

    • tilt mirrors in reverse when this feature is selected, the exterior sideview mirrors will tilt downward when the ignition is in the run position and the transmission shift lever/gear selector is in the reverse position. The mirrors will move back to their previous position when the transmis- sion ...

  • Page 357

    • rain sensing auto wipers when this feature is selected, the system will automati- cally activate the windshield wipers if it senses moisture on the windshield. To make your selection, press the “rain sensing” button on the touchscreen and make your selection. • hill start assist — if equipped when...

  • Page 358

    Setting. This warns you of a possible collision when you are much closer to the vehicle in front of you. To change the fcw status, press and release the “near”, “medium” or “far” button. For further information, refer to “adaptive cruise con- trol (acc)” in “understanding the features of your vehicl...

  • Page 359

    • lane departure warning (ldw) strength — if equipped when this feature is selected, it sets the strength of the steering wheel feedback for potential lane departures. The amount of directional torque the steering system can apply to the steering wheel to correct for vehicle lane departure can be se...

  • Page 360

    Activated in “lights” mode. When this mode is selected, the blind spot monitor (bsm) system is activated and will only show a visual alert in the exterior mirrors. When “lights & chime” mode is activated, the blind spot monitor (bsm) will show a visual alert in the exterior mirrors as well as an aud...

  • Page 361

    • headlights with wipers — if equipped when this feature is selected, and the headlight switch is in the auto position, the headlights will turn on ap- proximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by th...

  • Page 362

    • auto door locks when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press the “auto door locks” button on the touchscreen and select from “on” or “off.” • auto unlock on exit when this feature is selected,...

  • Page 363

    • remote door unlock when “remote door unlock” is selected, you may choose from “driver” or “all.” select “all” to have all doors unlock with the first push of the key fob. Select “driver” to have the only the driver door open with the first push of the key fob. Note: passive entry — if equipped. If...

  • Page 364

    • power lift gate alert — if equipped this feature plays an alert when the power lift gate is raising or lowering. To make your selection, press the “power lift gate alert” button on the touchscreen and select from “on” or “off.” auto comfort systems — if equipped after pressing the “auto-on comfort...

  • Page 365

    • engine off power delay when this feature is selected, the power window switches, radio, uconnect phone system (if equipped), dvd video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to off. Opening either fr...

  • Page 366

    • compass calibration press “compass calibration” on the touchscreen to enter calibration. To start calibration of the compass, press the “yes” button on the touchscreen and complete one or more 360-degree turns (in an area free from large metal or metallic objects). A message will appear on the tou...

  • Page 367

    • balance/fade this feature allows you to adjust the balance and fade settings. Press and drag the speaker icon or use the arrows to adjust, tap the “c” icon to readjust to the center. • speed adjusted volume this feature increases or decreases volume relative to vehicle speed. To change the speed a...

  • Page 368

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be available: • channel skip siriusxm can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scannin...

  • Page 369

    Select “yes” to restore, or “cancel” to exit. Once the settings are restored, a pop up appears stating ⬙settings reset to default. ⬙ clear personal data after pressing the “clear personal data settings” button on the touchscreen the following settings will be avail- able: • clear personal data when ...

  • Page 370

    Comfort, engine off options, audio, phone/ bluetooth, siriusxm setup, restore settings, clear personal data, and system information. Note: • only one touchscreen area may be selected at a time. • depending on the vehicles options, feature settings may vary. When making a selection, press the button ...

  • Page 371

    • display brightness with headlights on when in this display, you may select the brightness with the headlights on. Adjust the brightness with the “+” and “–” setting buttons on the touchscreen or by selecting any point on the scale between the “+” and “–” buttons on the touchscreen. Note: to make c...

  • Page 372

    • touchscreen beep when in this display, you may turn on or shut off the sound heard when button on the touchscreen is pressed. Press the “touchscreen beep” button on the touchscreen until a check-mark appears next to the setting, showing that setting has been selected. • controls screen time-out wh...

  • Page 373

    • distance select from: “mi” or “km.” • fuel consumption select from: “mpg” (us), “mpg” (uk), “l/100 km” or “km/l.” • pressure select from: “psi,” “kpa,” or “bar.” • temperature select from: “°c,” or “°f.” voice after pressing the “voice” button on the touchscreen the following settings will be avai...

  • Page 374

    Clock after pressing the “clock” button on the touchscreen the following settings will be available: • sync time with gps this feature will allow the radio to sync time with a gps signal. To change the sync time setting, press the “sync time with gps” button on the touchscreen until a check- mark ap...

  • Page 375

    Safety & driving assistance after pressing the “safety & driving assistance” button on the touchscreen the following settings will be avail- able: • forward collision warning — if equipped the front collision warning (fcw) feature provides an audible and/or visual warning to potential forward collis...

  • Page 376

    Information, refer to “forward collision warning (fcw) with mitigation” in “understanding the features of your vehicle.” • lane departure warning (ldw) — if equipped the lane departure warning (ldw) sets the distance at which the steering wheel will provide feedback for potential lane departures. Th...

  • Page 377

    Caution! • parksense is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • the vehicle mu...

  • Page 378

    • rear parksense braking assist to make your selection, press the “rear parksense brak- ing assist” button on the touchscreen, until a check-mark appears next to setting, indicating that the setting had been selected. Note: when this feature is selected, the parksense system will detect objects loca...

  • Page 379

    Note: if your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged, the sensor may have become misaligned. Take your vehicle to an authorized dealer to verify sensor alignment. Having a sensor that is misaligned will result in the bsm not oper...

  • Page 380

    • rain sensing auto wipers when this feature is selected, the system will automati- cally activate the windshield wipers if it senses moisture on the windshield. To make your selection, press the “rain sensing” button on the touchscreen, until a check- mark appears next to setting, indicating that t...

  • Page 381

    • headlight off delay when this feature is selected, it allows adjustment of the amount of time the headlights remain on after the engine is shut off. To change the headlights off delay setting, press the “+” or “–” button on the touchscreen to select your desired time interval, and choose either 0 ...

  • Page 382

    • daytime running lights — if equipped when this feature is selected, the headlights will turn on whenever the vehicle is set in motion. To make your selection, press the “daytime running lights” button on the touchscreen, until a check-mark appears next to setting, showing that setting has been sel...

  • Page 383

    • flash lights with lock when this feature is selected, the exterior lights will flash when the doors are locked or unlocked with the remote keyless entry (rke) transmitter, or when using the passive entry feature. This feature may be selected with or without the sound horn on lock feature selected....

  • Page 384

    Note: if the vehicle is programmed 1st press of key fob unlocks “all doors,” all doors will unlock no matter which passive entry equipped door handle is grasped. If 1st press of key fob unlocks “driver door” is pro- grammed, only the driver’s door will unlock when the driver’s door is grasped. With ...

  • Page 385

    • power lift gate chime — if equipped this feature plays an alert when the power lift gate is raising or lowering. To make your selection, press the “power lift gate chime” button on the touchscreen, until a check-mark appears next to setting, showing that setting has been selected. Auto-on comfort ...

  • Page 386

    Dvd video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to off. Opening either front door will cancel this feature. To change the engine off power delay status press the press the “+” or “-” button to choose ...

  • Page 387

    Note: bass/mid/treble allow you to simply slide your finger up or down to change the setting as well as press directly on the desired setting. • speed adjusted volume this feature increases or decreases volume relative to vehicle speed. To change the speed adjusted volume press the “off,” “1,” “2” o...

  • Page 388

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be available: • tune start tune start begins playing the current song from the beginning when you tune to a music channel using one of the twelve presets, so you can enjoy the co...

  • Page 389

    Note: siriusxm travel link is a separate subscription and is available for u.S. Residents only. Restore settings after pressing the “restore settings” button on the touchscreen the following settings will be available: • restore settings when this feature is selected it will reset the display, clock...

  • Page 390

    Uconnect radios — if equipped for detailed information about your uconnect radio, refer to your uconnect supplement manual. Ipod/usb/mp3 control — if equipped this feature allows an ipod or external usb device to be plugged into the usb port. Ipod control supports mini, 4g, photo, nano, 5g ipod and ...

  • Page 391

    • cycle the ignition to the on or acc position. • your vehicle may be equipped with a blu-ray disc player. If equipped with a blu-ray disc player, the icon will be present on the player. • turn on the rear seat entertainment system by press- ing the power button on the remote control. • when the vid...

  • Page 392

    1. Insert a blu-ray disc into the ves disc player with the label facing as indicated on the blu-ray player. The radio automatically selects the appropriate mode after the disc is recognized and displays the menu screen, the language screen, or starts playing the first track. 2. To watch a blu-ray di...

  • Page 393

    Dvd player play a dvd 1. Insert a dvd into the ves disc player with the label facing as indicated on the dvd player. The radio automatically selects the appropriate mode after the disc is recognized and displays the menu screen, or starts playing the first track. 2. To watch a dvd on rear 1 for driv...

  • Page 394

    2. While looking at rear 1 or 2, highlight disc by either pressing up/down/left/right buttons or by repeat- edly pressing the source button, then press enter/ok. Note: the ves will retain the last setting when turned off. Using the touch-screen radio controls 1. Press the media soft-key on the uconn...

  • Page 395

    3. Touch the 1 or 2 soft-key and then the disc soft-key in the media column. Note: • touching the screen on a touch-screen radio while a dvd is playing brings up basic remote control func- tions for dvd play such as scene selection, play, pause, ff, rw, and stop. Pressing the x in the upper corner w...

  • Page 396

    When connecting an external source to the aux/hdmi input, be sure to follow the standard color coding for the ves jacks: 1. Video in (yellow) 2. Left audio in (white) 3. Right audio in (red) note: certain high-end video game consoles will ex- ceed the power limit of the vehicle’s power inverter. Ref...

  • Page 397

    3. Touch the 1 soft-key and then touch either aux 1 or aux 2 in the ves column (depending which aux input is used). To exit press the back arrow soft-key at the top of the screen. Dual video screen note: typically there are two different ways to operate the features of the video entertainment system...

  • Page 398

    3. To watch a dvd on rear 2 for passenger’s side passengers, ensure the remote control and head- phone switch is on rear 2. Using the remote control 1. Press the mode/source button on the remote control. 2. While looking at rear 1 or 2, highlight ves disc by either pressing up/down/left/right button...

  • Page 399

    • the ves will retain the last setting when turned off. Using the touch-screen radio controls 1. Press the menu hard-key on the radio faceplate. 2. Touch the rear ves soft-key to display the rear ves controls. If a channel list is displayed, touch the hide list soft-key to display the rear ves contr...

  • Page 400

    Note: • to view a dvd on the radio press the radio/media hard-key, on the radio faceplate, then touch the disc tab soft-key and then the view video soft-key. • viewing a dvd on the touch-screen radio screen is not available in all states/provinces, and the vehicle must be stopped, and the shift leve...

  • Page 401

    2. While looking at the video screen, either press up/ down/left/right on the remote control to highlight the desired audio source or repeatedly press the mode/source button on the remote until the de- sired audio source appears on the screen. Using the touch-screen radio controls 1. Press the menu ...

  • Page 402

    3. To listen to an audio source on rear 2 while a video is playing on rear 1, touch the 2 soft-key and choose an audio source. To exit touch the back arrow soft-key at the top left of the left screen. Important notes for dual video screen system • ves is able to transmit two channels of stereo audio...

  • Page 403

    Blu-ray player remote control – if equipped controls and indicators 1. Power – turns the screen and wireless headphone transmitter for the selected channel on or off. To hear audio while the screen is closed, press the power button to turn the headphone transmitter on. 2. Channel selector indicators...

  • Page 404

    (if equipped) and the ves mode is selected and the disc is stopped, press the setup button to access the blu-ray setup menu. 7. 䉴䉴 – press and hold to fast forward through the current audio track or video chapter. 8. 䉴 / 㥋 (play/pause) – begin/resume or pause disc play. 9. Four colored buttons – pre...

  • Page 405

    • pushing the video lock again or turning the ignition off turns video lock off and allows remote control operation of the ves. Replacing the remote control batteries the remote control requires two aaa batteries for op- eration. To replace the batteries: • locate the battery compartment on the back...

  • Page 406

    Controls the headphone power indicator and controls are located on the right ear cup. Note: the rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video sys...

  • Page 407

    Note: • when both switches are on channel 1, the remote is controlling channel 1 and the headphones are tuned to the audio of the ves channel 1. • when both switches are on channel 2, the remote is controlling channel 2 and the headphones are tuned to the audio of the ves channel 2. 2. Press the mod...

  • Page 408

    Unwired stereo headphone lifetime limited warranty who does this warranty cover? This warranty covers the initial user or purchaser ( ⬙you⬙ or ⬙your⬙) of this particular unwired technology llc ( ⬙unwired⬙) wire- less headphone ( ⬙product⬙). The warranty is not transfer- able. How long does the cover...

  • Page 409

    Products, and is in lieu of all other war- ranties (express or implied), including any warranty or merchantability or fitness for a particular purpose. If you have any questions or comments regarding your unwired wireless headphones, please phone 1-888-293- 3332 or email customersupport@unwiredtechn...

  • Page 410

    The ves can even control radio modes or video modes while the radio is turned off. The ves can access the radio modes or disc modes by navigating to those modes on the ves and activating a radio mode or disc mode. Information mode display when information mode is active, the current mode setting for...

  • Page 411

    1. Channel 1 mode – displays the current source for channel 1. 2. Channel 1 audio only/mute — audio: the audio only icon is not used on channel 1, in a single screen system. Mute: when the mute icon is displayed, the audio for channel 1 has been muted using the remote control’s mute button. 3. Chann...

  • Page 412

    Numeric keypad menu when the display for either channel 1 or channel 2 shows direct tune, pressing the remote control’s enter button activates a numeric keypad menu. This screen makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Pres...

  • Page 413

    Station list menu when listening to satellite audio, pressing the remote control’s pop up/menu button displays a list of all available channels. Navigate this list using the remote control’s navigation buttons ( 䉱, 䉲) to find the desired station, press the remote control’s enter/ok button to tune to...

  • Page 414

    Display settings when watching a video source (dvd video with the disc in play mode, aux video, etc.), pressing the remote control’s setup button activates the display settings menu. These settings control the appearance of the video on the screen. The factory default settings are already set for op...

  • Page 415

    • close the video screen. • to change the current audio mode, press the remote control’s mode/source button. This will automati- cally select the next available audio mode without using the mode/source select menu. • when the screen is reopened, the video screen will automatically turn back on and s...

  • Page 416

    • cd: cd-da, vcd, cd-text • dvd/cd: mp3, wma, aac, divx (versions 3 – 6) profile 3.0 dvd region codes the ves dvd player and many dvd discs are coded by geographic region. These region codes must match in order for the disc to play. If the region code for the dvd disc does not match the region code ...

  • Page 417

    • open sessions are ignored. Only sessions that are closed are playable. • for multi-session cds that contain only multiple cd- audio sessions, the player will renumber the tracks so each track number is unique. • for cd data (or cd-rom) discs, always use the iso-9660 (level 1 or level 2), joliet, o...

  • Page 418

    • any file that is copy protected (such as those down- loaded from many online music stores) will not play. The dvd player will automatically skip the file and begin playing the next available file. • other compression formats such as aac, mp3 pro, ogg vorbis, and atrac3 will not play. The dvd playe...

  • Page 419

    The dvd player may shut down during extremely hot conditions, such as when the vehicle’s interior tempera- ture is above 120°f. When this occurs, the dvd player will display ⬙ves high temp⬙ and will shut off the ves displays until a safe temperature is reached. This shut- down is necessary to protec...

  • Page 420

    All of the language settings have a special ⬙other⬙ setting to accommodate languages other than japanese or eng- lish. These languages are selected using a special four- digit code. To enter a new language code, activate the dvd setup menu. To enter dvd setup menu stop the dvd, enter radio disc mode...

  • Page 421

    Rating and password setup the rating and password settings work together to control the types of dvds that your family watches. Most dvd- video discs have a rating (from 1 to 8) assigned to them where lower numbers are designated for all audiences and higher numbers are designated for more adult aud...

  • Page 422

    To set the password, activate the dvd setup menu and follow these additional instructions: • using the remote control left and right cursor but- tons, select the rating tab. • highlight ⬙change password⬙, and then press the remote control’s enter/ok button. • enter the current password. Select a dig...

  • Page 423

    To set the rating, activate the dvd setup menu and follow these additional instructions: • using the remote control’s left and right cursor buttons, select the rating tab. • highlight ⬙change rating⬙, and then press the remote control’s enter/ok button. • enter the current password. Select a digit, ...

  • Page 424

    • the software which has the copyrights of a third party and is distributed as free software. Please refer the contract details which are disclosed in following web- site, for example, concerning these above software. • www.Gnu.Org/licenses/old-licenses/gpl-2.0- standalone.Html • www.Gnu.Org/license...

  • Page 425

    Kernel2.6.16.29 freetype2 2.2.1 gcc sh4eb-3.4.5 glibc-2.3.5 boot_loader sh- ipl+g 1.00 libgcc_s-3.4.5 bash-3.0-31 busybox-1.00 makedev-1.1.0 module-init-tools- 3.1.0 libtermcap-2.0.8 mtd-utils-20050619 initscripts-8.11.1-1 libstdc++-3.4.5-10 libiconv-1.11 coreutils-6.9 dosfstools-2.10-3 directfb 1.0...

  • Page 426

    And/or (ii) decode avc video that was encoded by a consumer engaged in a per- sonal and non-commercial activity and/or was obtained from a video pro- vider licensed to provide avc video. No license is granted or shall be implied for any other use. Additional information may be obtained from mpeg la,...

  • Page 427

    Intellectual property rights. Use of this copyright pro- tection technology must be authorized by rovi corporation, and is intended for home and other limited viewing use only unless otherwise authorized by rovi corporation. Reverse engineering or disas- sembly is prohibited. • manufactured under li...

  • Page 428

    Caution! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Steering wheel audio controls — if equipped the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the whee...

  • Page 429

    Pushing the center button will make the radio switch between the various modes available (am/fm/sxm/ cd/aux/ves, etc.). The left-hand control is a rocker-type switch with a push-button in the center. The function of the left-hand control is different depending on which mode you are in. The following...

  • Page 430

    3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become ...

  • Page 431

    Nevertheless, the wireless radio will be used in such a manner that the radio is 20 cm or further from the human body. The internal wireless radio operates within guidelines found in radio frequency safety standards and recom- mendations, which reflect the consensus of the scientific community. The ...

  • Page 432

    By turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • increase the separation between the equipment and receiver. • consult the dealer or an experienced radio technician for help. Climate controls the air conditioni...

  • Page 433

    Buttons on the touchscreen the buttons on the touchscreen are accessible on the uconnect system screen. Button descriptions (applies to both the buttons on the faceplate and the buttons on the touchscreen) 1. Max a/c button press and release to change the current setting, the indicator illuminates w...

  • Page 434

    This function again will cause the max a/c operation to switch into manual mode and the max a/c indicator will turn off. 2. A/c button press and release to change the current setting, the indicator illuminates when a/c is on. Performing this function again will cause the a/c operation to switch into...

  • Page 435

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 436

    The passenger temperature setting with the driver tem- perature setting. Changing the passenger temperature setting while in sync will automatically exit this feature. 10. Blower control blower control is used to regulate the amount of air forced through the climate system. There are seven blower sp...

  • Page 437

    • bi-level mode air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demis- ter outlets. Note: bi-level mode is designed under comfort con- ditions to provide cooler air out of the panel outlets and warmer air from the ...

  • Page 438

    Note: in sync mode, this button will also automatically adjust the passenger temperature setting at the same time. 15. Temperature control (5.0 radio only) press the temperature button on the touchscreen to regulate the temperature of the air inside the passenger compartment. Moving the temperature ...

  • Page 439

    • if fog or mist appears on the windshield or side glass, select defrost mode and adjust blower speed if needed. • if your air conditioning performance seems lower than expected, check the front of the a/c condenser (lo- cated in front of the radiator), for an accumulation of dirt or insects. Clean ...

  • Page 440

    Note: in cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (button on the touchscreen greyed out) if conditions exist that could create fogging on the inside of the windshield. On systems with manual climate controls, the recir...

  • Page 441

    • the temperature can be displayed in u.S. Or metric units by selecting the uconnect customer- programmable feature. Refer to the “uconnect system settings” in this section of the manual. To provide you with maximum comfort in the automatic mode, during cold start-ups the blower fan will remain on l...

  • Page 442

    Coolant that meets the requirements of fca material standard ms.90032 and 50% water is recommended. Refer to “maintenance procedures” in “maintaining your vehicle” for proper coolant selection. Winter operation use of the air recirculation mode during winter months is not recommended because it may ...

  • Page 443

    Outside air intake make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves. Leaves collected in the air intake may reduce airflow, and if they enter the plenum, they could plug the water drains. In winter months, make sure the air intake is clear...

  • Page 444

    Control setting suggestions for various weather conditions 442 understanding your instrument panel.

  • Page 445

    Personalized menu bar the uconnect features and services in the main menu bar are easily changed for your convenience. Simply follow these steps: 1. Press the “apps ” button to open the app screen. 2. Press and hold, then drag the selected app to replace an existing shortcut in the main menu bar. Th...

  • Page 446

    If you see the icon on your touchscreen, you have the uconnect 8.4an system. If not, you have a uconnect 8.4a system. Get started all you need to control your uconnect system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com to check mobile device and feature compati...

  • Page 447

    4. Each time you give a voice command, you must first push either the vr or phone button, wait until after the beep, then say your voice command. 5. You can interrupt the help message or system prompts by pushing the vr or phone button and saying a voice command from current category. Uconnect voice...

  • Page 448

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect system. Push the vr button . After the beep, say: • cancel to stop a current voice session • help to hear a list of suggested voice commands • repeat to listen to the system prompts again notice t...

  • Page 449

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio stations you would like to hear. (subscrip- tion or included siriusxm satellite radio trial required.) push the vr button . After the beep, say: • tune to ninety-five-point-five fm • tune to satellite channel hits 1 tip: a...

  • Page 450

    Media uconnect offers connections via usb, sd, bluetooth and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands and ...

  • Page 451

    Phone making and answering hands-free phone calls is easy with uconnect. When the “phonebook” button is illumi- nated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the fol...

  • Page 452

    Voice text reply uconnect will announce incoming text messages. Push the phone button and say listen. (must have com- patible mobile phone paired to uconnect system.) 1. Once an incoming text message is read to you, push the phone button . After the beep, say: “reply.” 2. Listen to the uconnect prom...

  • Page 453

    Tip: voice text reply is not compatible with iphone, but if your vehicle is equipped with siri eyes free, you can use your voice to send a text message. Climate (8.4a/8.4an) too hot? Too cold? Adjust vehicle temperatures hands- free and keep everyone comfortable while you keep moving ahead. (if vehi...

  • Page 454

    Tip: voice command for climate may only be used to adjust the interior temperature of your vehicle. Voice command will not work to adjust the heated seats or steering wheel if equipped. Navigation (8.4a/8.4an) the uconnect navigation feature helps you save time and become more productive when you kn...

  • Page 455

    Tip: to start a poi search, push the vr button . After the beep, say: “ find nearest coffee shop.” uconnect access (8.4a/8.4an) warning! Always obey traffic laws and pay attention to the road. Some uconnect access services, including 9-1-1 and assist, will not work without an operable 1x (voice/data...

  • Page 456

    Note: uconnect access is available only on equipped vehicles purchased within the continental united states, alaska and hawaii. Services can only be used where coverage is available; see coverage map for details. 9-1-1 call security alarm notification remote door lock/unlock stolen vehicle assistanc...

  • Page 457

    2. Press the “uconnect care” button on the touchscreen. 3. A helpful uconnect care agent will register your vehicle and handle all of the details. Signing up is easy! Simply follow the steps above. Or, press the “apps ” button on the touchscreen to “register by web” to complete the process using you...

  • Page 458

    To link your internet radio accounts: 1. Download the uconnect access app to your mobile device. 2. Press the via mobile icon on the navigation bar at the bottom of the app. 3. Press the app you’d like to connect to your vehicle. 4. Enter your login information for the selected app and press link. 5...

  • Page 459

    Voice texting (8.4a/8.4an) 1. To send a message, push the phone button . After the beep, say the following command: “send mes- sage to john smith.” 2. Listen to the prompt. After the beep, dictate the message you would like to send. Wait for uconnect to process your message. 3. The uconnect system w...

  • Page 460

    Tip: • voice texting is not compatible with iphone, but if your vehicle is equipped with siri eyes free, you can use your voice to send a text message. • messages are limited to 140 characters. • the messaging button on the touchscreen must be illuminated to use the feature. Iphone notification sett...

  • Page 461

    Yelp (8.4a/8.4an) once registered with uconnect access, you can use your voice to search for the most popular places or things around you. 1. Press the “apps ” button on the touchscreen. 2. Press the “yelp” button on the touchscreen. 3. Once the yelp home screen appears on the touch- screen, push th...

  • Page 462

    Siriusxm travel link (8.4a/8.4an) need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? Siriusxm travel link is a suite of services that brings a wealth of information right to your uconnect 8.4an system. (not available for 8.4a system.) push th...

  • Page 463

    Siri eyes free — if equipped if your vehicle is equipped with siri eyes free, you can use your voice to send text messages, schedule meetings, set reminders, and more. For further information go to the mopar owner connect website moparownerconnect.Com. Do not disturb with do not disturb, you can dis...

  • Page 464

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 465

    Additional information © 2015 fca us llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of fca us llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. Yelp, yelp logo, yelp...

  • Page 467

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .471 ▫ automatic transmission . . . . . . . . . . . . . . . .471 ▫ keyless enter-n-go . . . . . . . . . . . . . . . . . . .472 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .472 ▫ extreme cold weather ...

  • Page 468

    ▫ brake/transmission shift interlock system . . .482 ▫ fuel economy (eco) mode . . . . . . . . . . . . . .483 ▫ eight–speed automatic transmission . . . . . . .484 䡵 four-wheel drive operation . . . . . . . . .493 ▫ quadra-trac i operating instructions/precautions — if equipped . . . . . . . . . . ....

  • Page 469

    ▫ traction downhill . . . . . . . . . . . . . . . . . . . . .518 ▫ after driving off-road . . . . . . . . . . . . . . . . .518 䡵 electric power steering . . . . . . . . . . . . .519 䡵 fuel saver technology 5.7l engine only — if equipped . . . . . . . . . . . . . . . . . . . . . . .520 䡵 parking brak...

  • Page 470

    ▫ tire terminology and definitions . . . . . . . . . .551 ▫ tire loading and tire pressure . . . . . . . . . . .552 䡵 tires — general information . . . . . . . .557 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .557 ▫ tire inflation pressures . . . . . . . . . . . . . . . . .558 ▫ ti...

  • Page 471

    ▫ gasoline/oxygenate blends . . . . . . . . . . . . . .581 ▫ e-85 usage in non-flex fuel vehicles . . . . . . .581 ▫ mmt in gasoline . . . . . . . . . . . . . . . . . . . . .582 ▫ materials added to fuel . . . . . . . . . . . . . . . .582 ▫ fuel system cautions. . . . . . . . . . . . . . . . . . .58...

  • Page 472

    ▫ recreational towing — quadra-trac i (single-speed transfer case) four-wheel drive models . . . . . . . . . . . . . . . . . . . . . . . . . . . . .608 ▫ recreational towing — quadra–trac ii /quadra–drive ii four-wheel drive models . .608 470 starting and operating.

  • Page 473

    Starting procedures before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • before exiting a vehicle, always shift the automatic transmission into park and apply ...

  • Page 474

    Caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • do not shift from reverse, park, or neutral into any forward gear when the engine is above idle speed. • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse...

  • Page 475

    4. If you wish to stop the cranking of the engine prior to the engine starting, push the button again. Note: normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. To turn off the engine using engine start/stop button 1. Place the shift lever...

  • Page 476

    Engine start/stop button functions — with driver’s foot off the brake pedal (in park or neutral position) the engine start/stop button operates similar to an ignition switch. It has four positions, off, acc, run and start. To change the ignition positions without starting the vehicle and use the acc...

  • Page 477

    Warning! (continued) • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. • if the...

  • Page 478

    After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Stop/start system — if equipped the stop/start function is developed to reduce fuel consumption. The system will stop the engine automati- cally during a vehicle stop if the required conditions are...

  • Page 479

    Possible reasons the engine does not autostop prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled. Detailed information about the operation of the stop/ start system may be viewed in the did stop/start screen. In the following situations t...

  • Page 480

    • steering angle beyond threshold. • acc is on and speed is set. It may be possible for the vehicle to be driven several times without the stop/start system going into a stop/start ready state under more extreme condi- tions of the items listed above. To start the engine while in autostop mode while...

  • Page 481

    To manually turn off the stop/start system 1. Push the stop/start off switch (located on the switch bank). The light on the switch will illuminate. 2. The “stop/start off” message will appear in driver information display (did). Refer to “driver information display (did)” in “understanding your inst...

  • Page 482

    If the “service stop/start system” message ap- pears in the did, have the system checked by your authorized dealer. Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet...

  • Page 483

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, and make sure the keyless ...

  • Page 484

    Caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into or out of park or reverse only after the vehicle has come to a complete stop. • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting i...

  • Page 485

    Fuel economy (eco) mode the fuel economy (eco) mode can improve the vehicle’s overall fuel economy during normal driving conditions. Push the “eco” switch in the center stack of the instru- ment panel to activate or disable eco mode. An amber light on the switch indicates when eco mode is disabled. ...

  • Page 486

    Eight–speed automatic transmission the transmission gear range (prnd) is displayed both on the shift lever and in the driver information display (did). To select a gear range, press the lock button on the shift lever and move the lever rearward or forward. You must also press the brake pedal to shif...

  • Page 487

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 488

    Note: on four-wheel drive vehicles be sure that the transfer case is in a drive position. Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle c...

  • Page 489

    Warning! (continued) • when leaving the vehicle, always make sure the ignition is in the off mode, remove the key fob from the vehicle, and lock the vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous...

  • Page 490

    • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral (n) use this range when the vehicle is standing for prolonged periods with the...

  • Page 491

    Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through all forward gears. The drive position provides optimum driving characteris- tics under all normal ope...

  • Page 492

    Result in transmission damage, transmission limp home mode is activated. In this mode, the transmission may operate only in certain gears, or may not shift at all. Vehicle performance may be severely degraded and the engine may stall. In some situations, the transmission may not re-engage if the eng...

  • Page 493

    Autostick autostick is a driver-interactive transmission feature providing manual shift control, giving you more control of the vehicle. Autostick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provi...

  • Page 494

    • the transmission will automatically downshift to first gear when coming to a stop. After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated. • you can start out, from a stop, in first or second gear (or third gear, in 4lo range, snow mode, or sand mode). ...

  • Page 495

    Four-wheel drive operation quadra-trac i operating instructions/precautions — if equipped the quadra-trac i is a single-speed (hi range only) transfer case, which provides convenient full-time four- wheel drive. No driver interaction is required. The brake traction control (btc) system, which combin...

  • Page 496

    When operating your vehicle in 4wd low, the engine speed is approximately three times that of the 4wd hi position at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and c...

  • Page 497

    Note: refer to “selec-terrain – if equipped” in “start- ing and operating” for further information on the vari- ous positions and their intended usages. Neutral this range disengages the driveline from the powertrain. It is to be used for flat towing behind another vehicle. Refer to “recreational to...

  • Page 498

    Shifting procedures 4wd hi to 4wd low with the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), the ignition switch in the on position or the engine running, shift the transmission into “n”, and push the “4wd low” button once on the transfer case switch. The “4wd low” indicator light in the instrument...

  • Page 499

    Note: if shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “for 4x4 low slow below 3 mph (5 km/h) put trans in “n” press 4 low” message will flash from the driver information display (did). Refer to “driver in- formation display (did)” in “u...

  • Page 500

    Shifting into neutral (n) warning! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neutral (n) position without first fully engaging the parking brake. The neutral (n) position dis- engages both the front and rear drive shafts from the power...

  • Page 501

    6. After the shift is completed and the neutral (n) light stays on, release the neutral (n) button. 7. Shift the transmission into reverse. 8. Release the brake pedal for five seconds and ensure that there is no vehicle movement. Note: if shift conditions/interlocks are not met, a “to tow vehicle sa...

  • Page 502

    6. Using a ballpoint pen or similar object, push and hold the recessed transfer case neutral (n) button (lo- cated by the selector switch) for one second. 7. When the neutral (n) indicator light turns off, release the neutral (n) button. 8. After the neutral (n) button has been released, the transfe...

  • Page 503

    Selec-terrain — if equipped description selec-terrain combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance for all terrains. Selec-terrain consists of the following positions: • snow – tuning set for additional stability in inclement weat...

  • Page 504

    • sand – off road calibration for use on low traction surfaces such as sand or wet grass. Driveline is maxi- mized for traction. Some binding may be felt on less forgiving surfaces. The electronic brake controls are set to limit traction control management of throttle and wheel spin. If equipped wit...

  • Page 505

    Quadra-lift — if equipped description the quadra-lift air suspension system provides full time load leveling capability along with the benefit of vehicle height adjustment by the push of a button. Selec-terrain switch 1 — up button 2 — down button 3 — entry/exit mode indicator lamp (customer selecta...

  • Page 506

    • normal ride height (nrh) – this is the standard position of the suspension and is meant for normal driving. • off-road 1 (or1) (raises the vehicle approximately 1.1 in (28 mm) – this is the primary position for all off-road driving until or2 is needed. A smoother and more comfortable ride will res...

  • Page 507

    Speed falls below 20 mph (32 km/h). The vehicle will enter aero mode, regardless of vehicle speed if the vehicle is in “sport” mode. • entry/exit mode (lowers the vehicle approximately 1.6 in (40 mm) – this position lowers the vehicle for easier passenger entry and exit as well as lowering the rear ...

  • Page 508

    The system requires that the engine be running for all changes. When lowering the vehicle all of the doors, including the liftgate, must be closed. If a door is opened at any time while the vehicle is lowering the change will not be completed until the open door(s) is closed. The quadra-lift air sus...

  • Page 509

    Air suspension modes the air suspension system has multiple modes to protect the system in unique situations: tire/jack mode to assist with changing a spare tire, the air suspension system has a feature which allows the automatic leveling to be disabled. Refer to “uconnect settings” in “under- stand...

  • Page 510

    Driver information display (did) messages when the appropriate conditions exist, a message will appear in the did display. Refer to “driver information display (did)” in “understanding your instrument panel” for further information. Operation the indicator lamps 3 through 6 will illuminate to show t...

  • Page 511

    • off-road 2 (or2) – indicator lamps 4, 5, and 6 will be illuminated when the vehicle is in or2. • off-road 1 (or1) – indicator lamps 4 and 5 will be illuminated when the vehicle is in or1. • normal ride height (nrh) – indicator lamp 4 will be illuminated when the vehicle is in this position. • entr...

  • Page 512

    On-road driving tips utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher center of gravity than ordinary vehicles. An advantage of the higher ground cleara...

  • Page 513

    Note: on summit models the lower front fascia is not removable. Lower front fascia removal: 1. Remove the seven quarter turn fasteners. 2. Starting on one side of the vehicle, disengage lower fascia from the upper fascia. Grasp the portion inside the wheel well. Pulling it downwards and toward you, ...

  • Page 514

    Radar sensor removal procedure (if equipped with adaptive cruise control [acc]): 1. With the lower fascia removed, which provides access to the sensor and bracket, disconnect the wiring harness from the sensor. 2. Using a suitable tool, disconnect the wire clip from the bracket. 3. Using a suitable ...

  • Page 515

    5. Remove the plug from the protective connector and install on the sensor. 6. Insert the wiring harness connector into the protective connector. 7. Store sensor and bracket in a safe place. Note: all cruise control functions will be disabled when the radar sensor is disconnected. Radar sensor insta...

  • Page 516

    Note: • it may be necessary to apply additional force to individual tabs to make sure they are fully engaged. • do not use any tools to apply additional force to the tabs as damage to the upper and lower fascias may result. 4. Reinstall the seven quarter turn fasteners. Quadra-lift — if equipped whe...

  • Page 517

    Warning! (continued) driveshafts. Driving in 4wd-low on pavement will cause driveline binding; use only on wet or slippery surfaces. Driving through water although your vehicle is capable of driving through water, there are a number of precautions that must be considered before entering the water. N...

  • Page 518

    Flowing water if the water is swift flowing and rising (as in storm run-off), avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of 9 inches (23 cm). The flowing water can erode the streambed, causing your vehicle to s...

  • Page 519

    Hill climbing note: before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4wd low. Use first gear and 4wd low for very steep hills. If you stall or begin t...

  • Page 520

    Traction downhill when descending mountains or hills, use hill descent or selec-speed control to avoid repeated heavy braking. If not equipped with hill descent or selec-speed control use the following procedure: shift the transmission into a low gear, and the transfer case into 4wd low range. Let t...

  • Page 521

    • after extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. ...

  • Page 522

    Warning! Continued operation with reduced assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. If the electric power steering warning icon is displayed and the “service power steer- ing” or the “power steering assist off – service system” message is...

  • Page 523

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the park position. The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully....

  • Page 524

    Note: • when the parking brake is applied and the transmis- sion is placed in gear, the “brake” warning light will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that the park...

  • Page 525

    Warning! (continued) • do not leave the key fob in or near the vehicle or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n-go in the acc or on/run mode. A child could operate power windows, other con- trols, or move the vehicle. • be sure...

  • Page 526

    Brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating. Electronic brake control system your vehicle is equipped with an advanced electronic brake control system (ebc). This system includes elec- tronic br...

  • Page 527

    Anti-lock brake system (abs) the anti-lock brake system (abs) provides increased vehicle stability and brake performance under most braking conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking. The abs performs a self-check cycle to ensure that the ab...

  • Page 528

    Warning! (continued) • pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the abs cannot prevent the natural laws of phys- ics from acti...

  • Page 529

    Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 530

    Does not apply the throttle before this time expires, the system will release brake pressure and the vehicle will roll down the hill as normal. The following conditions must be met in order for hsa to activate: • the feature must be enabled. • the vehicle must be stopped. • park brake must be off. •...

  • Page 531

    Towing with hsa hsa will also provide assistance to mitigate roll back while towing a trailer. Warning! • if you use a trailer brake controller with your trailer, the trailer brakes may be activated and deactivated with the brake switch. If so, there may not be enough brake pressure to hold both the...

  • Page 532

    • if disabling hsa using uconnect settings, refer to “uconnect settings” in “understanding your instru- ment panel” for further information. For vehicles not equipped with the did, perform the following steps: 1. Center the steering wheel (front wheels pointing straight forward). 2. Shift the transm...

  • Page 533

    Other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. Bld may remain enabled even if tcs and esc are in a reduced mode. Electronic stability control (esc) this system enhances directional control and stabilit...

  • Page 534

    Warning! • electronic stability control (esc) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slipper...

  • Page 535

    Esc on this is the normal operating mode for the esc. When- ever the vehicle is started, the esc system will be in this mode. This mode should be used for most driving conditions. Alternate esc modes should only be used for specific reasons as noted in the following paragraphs. Partial off the “part...

  • Page 536

    Full off – if equipped this mode is intended for off-highway or off-road use only and should not be used on any public roadways. In this mode, tcs and esc features are turned off. To enter the “full off” mode, push and hold the “esc off” switch for five seconds while the vehicle is stopped with the ...

  • Page 537

    Malfunction has been detected in the esc system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. T...

  • Page 538

    Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicle’s speed are sufficient to potentially cause wheel li...

  • Page 539

    Follow the trailer tongue weight recommendations. Refer to “trailer towing” in this section for further informa- tion. When tsc is functioning, the “esc activation/ malfunction indicator light” will flash, the engine power may be reduced and you may feel the brakes being applied to individual wheels...

  • Page 540

    Optimal steering behavior in order to reach/maintain vehicle stability. The only notification the driver receives that the feature is active is the torque applied to the steering wheel. Note: the dst feature is only meant to help the driver realize the correct course of action through small torques ...

  • Page 541

    Activating hdc once hdc is enabled, it will activate automatically if driven down a grade of sufficient magnitude. The set speed for hdc is selectable by the driver, and can be adjusted by using the gear shift +/-. The following summarizes the hdc set speeds: hdc target set speeds • p = no set speed...

  • Page 542

    Deactivating hdc hdc will be deactivated but remain available if any of the following conditions occur: • driver overrides hdc set speed with throttle or brake application. • vehicle speed exceeds 20 mph (32 km/h) but remains below 40 mph (64 km/h). • vehicle is on a downhill grade of insufficient m...

  • Page 543

    • the cluster icon and switch lamp will flash for several seconds then extinguish when the driver pushes the hdc switch but enable conditions are not met. • the cluster icon and switch lamp will flash for several seconds then extinguish when hdc disables due to excess speed. • the cluster icon and s...

  • Page 544

    • vehicle speed is below 5 mph (8 km/h) • parking brake is released. • driver door is closed. • driver is not applying throttle. Activating ssc once ssc is enabled it will activate automatically once the following conditions are met: • driver releases throttle. • driver releases brake. • transmissio...

  • Page 545

    • neutral = 1.2 mph (2 km/h) • park = ssc remains enabled but not active note: • during ssc the +/- shifter input is used for ssc target speed selection but will not affect the gear chosen by the transmission. While actively controlling ssc the transmission will shift appropriately for the driver- s...

  • Page 546

    • the vehicle is driven greater than 20 mph (32 km/h) for greater than 70 seconds. • the vehicle is driven greater than 40 mph (64 km/h) (ssc exits immediately). Feedback to the driver: the instrument cluster has an ssc icon and the ssc switch has an led which offer feedback to the driver about the ...

  • Page 547

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 548

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 549

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ....Blank....ⴖ = passenger car tire based on european design standards, or lt = light truck tire based o...

  • Page 550

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 551

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 552

    Example: dot ma l9 abcd 0301 01 = number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represen...

  • Page 553

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 554

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 552 starting an...

  • Page 555

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 556

    To determine the maximum loading conditions of your vehicle, locate the statement “the combined weight of occupants and cargo should never exceed xxx lbs or xxx kg” on the tire and loading information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) ...

  • Page 557

    Note: • if your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. The follow- ing table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and num- ber and size of occupan...

  • Page 558

    556 starting and operating.

  • Page 559

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 560

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 561

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 562

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits ...

  • Page 563

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 564

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 565

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Run flat tires — if equipped run flat tires a...

  • Page 566

    Equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spa...

  • Page 567

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 568

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 569

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (1.6 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information....

  • Page 570

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance w...

  • Page 571

    Warning! (continued) braking of your vehicle. This can cause unpredict- able handling and stress to steering and suspen- sion components. You could lose control and have a collision resulting in serious injury or death. Use only the tire and wheel sizes with load ratings approved for your vehicle. •...

  • Page 572

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 573

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation ...

  • Page 574

    Tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recommended cold tire placard pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the...

  • Page 575

    Of 33 psi (227 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressure is 28 psi (193 kpa), a temperature drop to 20°f (-7°c) will decrease the tire pressure to approximately 24 psi (165 kpa). This tire pressure is sufficiently low enough to turn on the tire pressure monitorin...

  • Page 576

    Note: • the tpms is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat ...

  • Page 577

    Note: it is particularly important, for you to regularly check the tire pressure in all of your tires and to maintain the proper pressure. The tire pressure monitor system (tpms) consists of the following components: • receiver module • four tire pressure monitoring sensors • various tire pressure m...

  • Page 578

    Note: your system can be set to display pressure units in psi, bar or kpa. Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is in a different color on the graphic display to the vehicle’s recommended cold ...

  • Page 579

    Service tpm system warning the tire pressure monitoring telltale light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime. The did will display a “service tpm sys- tem” message for a minimum of five seconds. This messag...

  • Page 580

    Note: there is no tire pressure monitoring sensor in the spare tire. The tpms will not be able to monitor the tire pressure. If you install the spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition switch cycle, the tire pressure monitori...

  • Page 581

    General information this device complies with part 15 of the fcc rules and rss-210 of industry canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may caus...

  • Page 582

    Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consid- ering service for the vehicle. 5.7l engine — if equipped this engine is designed to meet all emis- sions regulations and provide s...

  • Page 583

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Caution! Do not use gasoline containing methanol or gaso- line containing more than 15% ethanol (e-15). Use of these blends may result in starting and drivability problems, damage critical fuel s...

  • Page 584

    Mmt in gasoline methylcyclopentadienyl manganese tricarbonyl (mmt) is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended wi...

  • Page 585

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine per- formance and damage the emissions control sys- tem. • an out-of-tune engine or certain fuel or ignitio...

  • Page 586

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 587

    Adding fuel 1. Press the fuel filler door release switch (located under the headlamp switch). 2. Open the fuel filler door. Note: in certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel doo...

  • Page 588

    3. There is no fuel filler cap. A flapper door inside the pipe seals the system. 4. Insert the fuel nozzle fully into the filler pipe, the nozzle opens and holds the flapper door while refuel- ing. 5. Fill the vehicle with fuel, when the fuel nozzle “clicks” or shuts off the fuel tank is full. 6. Wa...

  • Page 589

    Warning! • never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled. • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the “malfunction indicator light” to turn on. • ...

  • Page 590

    Note: if the fuel door does not latch after the manual release cable has been activated, the actuator latch should be manually returned to the closed position. Vehicle loading certification label as required by national highway traffic safety admin- istration regulations, your vehicle has a certific...

  • Page 591

    Payload the payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo. Gross axle weight rating (gawr) the gawr is the maximum permissible load on the front and rear axles. The load must be distributed in the...

  • Page 592

    Loading the actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. The entire vehicle should first be weighed on a commer- cial scale to insure that the gvwr has not been exceeded. The we...

  • Page 593

    To maintain the new vehicle limited warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing. Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross ...

  • Page 594

    Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Gross axle weight rating (gawr) the gawr is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure t...

  • Page 595

    If equipped, the electronic trailer sway control (tsc) recognizes a swaying trailer and automatically applies individual wheel brakes and/or reduces engine power to attempt to eliminate the trailer sway. Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it ...

  • Page 596

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 597

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain: engine model frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l (std cooling) 4x2 55 sq ft (5.11 sq m) 3,500 lbs (...

  • Page 598

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further information. The addition of...

  • Page 599

    2. Pull the bottom of the cover outward (towards you), pull downwards to disengage the tabs located at the top of the hitch receiver cover. To reinstall the hitch receiver cover after towing repeat the procedure in reverse order. Note: be sure to engage all tabs of the hitch receiver cover in the bu...

  • Page 600

    Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer • the weight of any other type of cargo or equipment put in or on your vehicle • the weight of the driver and all passengers note: remember that everything put into or on the tr...

  • Page 601

    Caution! (continued) • then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. This helps the engine and other parts of the vehicle wear in at the heavier loads. Perform the maintenance listed in the “maintenance ...

  • Page 602

    Warning! (continued) • safety chains must always be used between your vehicle and trailer. Always connect the chains to the hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parked on a gr...

  • Page 603

    • check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “starting and operating” for the proper inspection procedure. • when replacing tires, refer to “tires – general infor- mation” in “starting and operating” for the proper tire repl...

  • Page 604

    • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • an electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. W...

  • Page 605

    Four-pin connector 1 — female pins 2 — male pin 3 — ground 4 — park 5 — left stop/turn 6 — right stop/turn seven-pin connector 1 — battery 2 — backup lamps 3 — right stop/turn 4 — electric brakes 5 — ground 6 — left stop/turn 7 — running lamps 5 starting and operating 603.

  • Page 606

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic. Automatic transmission the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. However, ...

  • Page 607

    • use speed control in flat terrain and with light loads to maximize fuel efficiency. Cooling system to reduce potential for engine and transmission over- heating, take the following actions: city driving when stopped for short periods of time, shift the trans- mission into neutral and increase engi...

  • Page 608

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models without 4–lo range four-wheel drive models with 4–lo range flat tow none not allowed not allowed see instructions • transmissi...

  • Page 609

    Note: • when recreational towing your vehicle, always follow applicable state and provincial laws. Contact state and provincial highway safety offices for additional de- tails. • vehicles equipped with quadra-lift must be placed in transport mode before tying them down (from the body) on a trailer o...

  • Page 610

    6. Install a suitable clamping device, designed for tow- ing, to secure the front wheels in the straight position. Caution! Towing with the rear wheels on the ground will cause severe transmission damage. Damage from improper towing is not covered under the new vehicle limited warranty. Recreational...

  • Page 611

    Caution! • do not dolly tow any 4wd vehicle. Towing with only one set of wheels on the ground (front or rear) will cause severe transmission and/or transfer case damage. Tow with all four wheels either on the ground, or off the ground (using a vehicle trailer). • tow only in a forward direction. Tow...

  • Page 612

    Warning! (continued) position disengages both the front and rear drive- shafts from the powertrain and will allow the vehicle to roll, even if the transmission is in park. The parking brake should always be applied when the driver is not in the vehicle. Use the following procedure to prepare your ve...

  • Page 613

    6. After the shift is completed and the neutral (n) light stays on, release the neutral (n) button. 7. Shift the transmission into reverse. 8. Release the brake pedal for five seconds and ensure that there is no vehicle movement. 9. Shift the transmission back into neutral. 10. With the transmission...

  • Page 614

    Note: • steps 1 through 4 are requirements that must be met before pressing the neutral (n) button, and must continue to be met until the shift has been completed. If any of these requirements are not met before press- ing the neutral (n) button or are no longer met during the shift, then the neutra...

  • Page 615

    6. Using a ballpoint pen or similar object, press and hold the recessed transfer case neutral (n) button (lo- cated by the selector switch) for one second. 7. When the neutral (n) indicator light turns off, release the neutral (n) button. After the neu- tral (n) button has been released, the transfe...

  • Page 616

    Note: • steps 1 through 5 are requirements that must be met before pressing the neutral (n) button, and must continue to be met until the shift has been completed. If any of these requirements are not met before press- ing the neutral (n) button or are no longer met during the shift, the neutral (n)...

  • Page 617

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .616 䡵 if your engine overheats . . . . . . . . . . . .616 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .617 ▫ torque specifications . . . . . . . . . . . . . . . . . . .618 䡵 jacking...

  • Page 618

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank just above the climate controls. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency....

  • Page 619

    • you can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling system could damage ...

  • Page 620

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 130 ft-lbs (176 n·m) m14 x 1.50 22 mm **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the ...

  • Page 621

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to...

  • Page 622

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack location the scissor-type jack and tire changin...

  • Page 623

    Note: the funnel for the cap-less fuel system is located on top of the spare tire. If your vehicle is out of fuel and an auxiliary fuel can is needed, insert the funnel into the filler neck and proceed to fill the vehicle. For vehicles not equipped with a spare tire, the fuel filler funnel is stored...

  • Page 624

    3. Set the parking brake. 4. Place the shift lever into park. 5. Turn the ignition off. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For ex- ample, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the veh...

  • Page 625

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 626

    3. Assemble the jack and jacking tools. Jack and tool assembly jacking locations 624 what to do in emergencies.

  • Page 627

    4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle until you are sure the jack is fully engaged. Lift point symbol on sill molding front jacking location 6 what to do in em...

  • Page 628

    5. For a rear tire, place the jack in the slot on the rear tie-down bracket, just forward of the rear tire (as indicated by the triangular lift point symbol on the sill molding). Do not raise the vehicle until you are sure the jack is fully engaged. 6. Raise the vehicle by turning the jack screw clo...

  • Page 629

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 7. Remove the lug nuts and wheel. 8. Position the spare wheel/tire on the vehicle and install the lug nuts with ...

  • Page 630

    9. Lower the vehicle by turning the jack screw counter- clockwise, and remove the jack and wheel blocks. 10. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. ...

  • Page 631

    Note: do not drive with the spare tire installed for more than 50 miles (80 km) at a max speed of 50 mph (80 km/h). Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places prov...

  • Page 632

    Jump-starting if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. Warni...

  • Page 633

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 634

    2. Turn off the heater, radio, and all unnecessary electri- cal accessories. 3. Remove the protective cover over the remote positive (+) battery post. Pull upward on the cover to remove it. 4. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set th...

  • Page 635

    Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery. 3. Connect the negative end (-) of the jumper cabl...

  • Page 636

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the remote negative (-) post of the discharged vehicle. 2. Disconnect the opposite end of the negative (-) jumper cable from th...

  • Page 637

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Push and hold the lock button on the shift lever. Then shift back and forth between drive and re...

  • Page 638

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 639

    Warning! • do not use a chain for freeing a stuck vehicle. Chains may break, causing serious injury or death. • stand clear of vehicles when pulling with tow hooks. Tow straps may become disengaged, caus- ing serious injury. Caution! Tow hooks are for emergency use only, to rescue a vehicle stranded...

  • Page 640

    2. Open the center console and locate the manual park release cover, remove it by snapping the cover away from the console hinges. 3. Using a screwdriver or similar tool, push the metal latch in towards the tether strap. Manual park release cover release latch 638 what to do in emergencies.

  • Page 641

    4. While the metal latch is in the open position, simulta- neously pull upwards on the tether strap until the lever clicks and latches in the released position. The transmission is now out of park and the vehicle can be moved. Caution! Closing the armrest while the manual park release is activated m...

  • Page 642

    To disengage the manual park release lever: 1. To disengage the manual park release apply tension upward while pushing the release latch towards the tether to unlock the lever. 2. Once the tension has been released and the lever has been unlocked be sure it is stowed properly and locks into position...

  • Page 643

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. If the trans- mission and drivetrain are operable, disabled vehicles may also be towed as described under “recreational towing” in the “starting and operating” section. Note: ...

  • Page 644

    Towing condition wheels off the ground two-wheel drive models four-wheel drive models without 4–lo range four-wheel drive models with 4–lo range flat tow none not allowed not allowed see instructions • transmission in park • transfer case in neutral (n) • tow in forward direction dolly tow front not...

  • Page 645

    If you must use the accessories (wipers, defrosters, etc.) while being towed, the ignition must be in the on/run position, not the acc position. If the key fob is unavailable, or the vehicle’s battery is discharged, refer to “manual park release” in this section for instructions on shifting the tran...

  • Page 646

    If the transmission is not operable, or the vehicle must be towed faster than 30 mph (48 km/h) or farther than 30 miles (48 km), tow with the rear wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed, or with the front wheels raised and the rear wheels on a towing dolly, or ...

  • Page 647

    Caution! • front or rear wheel lifts must not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when towing. • towing this vehicle in violation of the above re- quirements can cause severe transmission and/or transfer case damage. Damage f...

  • Page 649

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . .649 䡵 engine compartment — 5.7l . . . . . . . . . .650 䡵 onboard diagnostic system (obd ii) . . .651 ▫ onboard diagnostic system (obd ii) cybersecurity . . . . . . . . . . . . . . . . . . . . . . . .651 䡵 emissions insp...

  • Page 650

    ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .686 ▫ front/rear axle fluid . . . . . . . . . . . . . . . . . .688 ▫ transfer case . . . . . . . . . . . . . . . . . . . . . . . .689 ▫ automatic transmission . . . . . . . . . . . . . . . .690 ▫ appearance care and protection from corros...

  • Page 651

    Engine compartment — 3.6l 1 — remote jump start positive terminal 6 — engine oil fill 2 — engine oil dipstick 7 — brake fluid reservoir 3 — power distribution center (fuses) 8 — air cleaner filter 4 — coolant pressure cap (reservoir) 9 — washer fluid reservoir 5 — remote jump start negative terminal...

  • Page 652

    Engine compartment — 5.7l 1 — remote jump start positive terminal 6 — engine coolant reservoir 2 — engine oil dipstick 7 — engine oil fill 3 — power distribution center (fuses) 8 — brake fluid reservoir 4 — coolant pressure cap (radiator) 9 — air cleaner filter 5 — remote jump start negative termina...

  • Page 653

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 654

    Warning! • only an authorized service technician should con- nect equipment to the obd ii connection port in order to diagnose or service your vehicle. • if unauthorized equipment is connected to the obd ii connection port, such as a driver-behavior tracking device, it may: • be possible that vehicl...

  • Page 655

    Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station. To check if your vehicle’s obd ii system is ready, you must do the following: 1. Cycle the ignition switch to the on position, but do not crank or start the engine. Note: if you crank or start the...

  • Page 656

    Replacement parts use of genuine mopar parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-mopar parts for maintenance and repairs will not be covered by the new vehicle limited warranty. Dealer se...

  • Page 657

    Besides those maintenance items specified in the fixed “maintenance schedule”, there are other components which may require servicing or replacement in the future. Caution! • failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs...

  • Page 658

    Dipstick. Adding one quart of oil when the reading is at the bottom of the safe zone will result in a reading at the top of the safe zone on these engines. Caution! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change engine oil...

  • Page 659

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil selection for best performance and maximum protection under all types of operating conditions, the manufacturer only recommends ...

  • Page 660

    The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the “engine com- partment” illustration in this section. Note: vehicles equipped with a 5.7l engine must use sae 5w-20 oil. Failure to do so may resu...

  • Page 661

    Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only h...

  • Page 662

    Gasoline engine air cleaner filter inspection and replacement inspect engine air cleaner filter for dirt and or debris, if you find evidence of either dirt or debris you should change your air cleaner filter. Engine air cleaner filter removal 1. Release the spring clips from the air cleaner cover. A...

  • Page 663

    2. Lift the air cleaner cover to access the air cleaner filter. 3. Remove the air cleaner filter element from the housing assembly. Open air cleaner filter assembly 1 — air cleaner cover 2 — air cleaner filter air cleaner filter 1 — air cleaner filter 2 — air cleaner filter inspection surface 7 main...

  • Page 664

    Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleaner filter inspection surface facing downward. 2. Install the air clea...

  • Page 665

    However, cracks running along a rib (not across) are not normal. Any belt with cracks running along a rib must be replaced. Also have the belt replaced if it has excessive wear, frayed cords or severe glazing. Conditions that would require replacement: • rib chunking (one or more ribs has separated ...

  • Page 666

    Belt replacement on some models requires the use of special tools, we recommend having your vehicle ser- viced at an authorized dealer. Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning...

  • Page 667

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 668

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r134a — if equipped r-134a air conditioning refrigerant is a hydrofl...

  • Page 669

    Air conditioning filter replacement (a/c air filter) refer to the “maintenance schedule” for the proper maintenance intervals. Warning! Do not remove the a/c air filter while the vehicle is running, or while the ignition is in the acc or on/run mode. With the a/c air filter removed and the blower op...

  • Page 670

    2. There are glove compartment travel stops on both sides of the glove compartment door, partially close the glove compartment door and push inward to release the glove compartment travel stop on one side and repeat this procedure for the opposite side. 3. Pull the right hand side of the glove compa...

  • Page 671

    Pulling the door outward. Unhinge the filter cover on the right side to fully remove the cover. 6. Remove the a/c air filter by pulling it straight out of the housing. 7. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure th...

  • Page 672

    9. Push the door to the near closed position to reengage the glove compartment travel stops. Note: ensure the glove compartment door hinges and glove compartment travel stops are fully engaged. Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot po...

  • Page 673

    Note: life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may be present with chattering, marks, water lines or wet spots. If any of these conditions are present, clean the wiper blades or replace as neces- sary. The wiper blades a...

  • Page 674

    2. To disengage the wiper blade from the wiper arm, flip up the release tab on the wiper blade and while holding the wiper arm with one hand, slide the wiper blade down towards the base of the wiper arm. Wiper blade with release tab in locked position 1 — wiper 2 — release tab 3 — wiper arm wiper bl...

  • Page 675

    3. With the wiper blade disengaged, remove the wiper blade from the wiper arm by holding the wiper arm with one hand and separating the wiper blade from the wiper arm with the other hand (move the wiper blade toward the right side of the vehicle to separate the wiper blade from the wiper arm). 4. Ge...

  • Page 676

    Installing the front wipers 1. Lift the wiper arm off of the glass, until the wiper arm is in the full up position. 2. Position the wiper blade near the hook on the tip of the wiper arm with the wiper release tab open and the blade side of the wiper facing up and away from the windshield. 3. Insert ...

  • Page 677

    2. Lift the rear wiper arm fully off the glass. Wiper pivot cap in unlocked position 1 — wiper arm pivot cap 2 — wiper arm wiper blade in folded out position 1 — wiper arm pivot cap 2 — wiper arm 3 — wiper blade 7 maintaining your vehicle 675.

  • Page 678

    3. To remove the wiper blade from the wiper arm, grasp the bottom end of the wiper blade nearest to wiper arm with your right hand. With your left hand hold the wiper arm as you pull the wiper blade away from the wiper arm past its stop far enough to unsnap the wiper blade pivot pin from the recepta...

  • Page 679

    Installing the rear wiper 1. Lift the rear wiper arm pivot cap away from the glass to allow the rear wiper blade to be raised off of the glass. Note: the rear wiper arm cannot be fully raised off the glass unless the wiper arm pivot cap is unsnapped first. Attempting to fully raise the rear wiper ar...

  • Page 680

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine ...

  • Page 681

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 682

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 683

    For any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiat...

  • Page 684

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 685

    Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze) that meets the requirements of fca material standard ms.90032. When adding engine coolant (antifreeze): • we recommend using mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic ...

  • Page 686

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery tank. The cap should be inspected and cleaned if there is any accumulation of foreign mater...

  • Page 687

    Coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine off and cold, the level of the engine coolant (antifreeze) in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely ...

  • Page 688

    • if frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested for leaks. • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms.90032) and distilled water for proper corrosion protection of your engine w...

  • Page 689

    Fluid level check — brake master cylinder the fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the brake system warning lamp indicates system failure. The brake master cylinder has a plastic reservoir. On the outboard side of the reserv...

  • Page 690

    Warning! (continued) cause it to boil unexpectedly during hard or pro- longed braking, resulting in sudden brake failure. This could result in a collision. • overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire. Brake flu...

  • Page 691

    The rear axle fill and drain plugs should be tightened to 22 to 29 ft lbs (30 to 40 n·m). Caution! Do not overtighten the plugs as it could damage them and cause them to leak. Selection of lubricant use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “m...

  • Page 692

    Selection of lubricant use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for further information. Automatic transmission selection of lubricant it is important to use the proper transmission fluid to ensure optimum transmi...

  • Page 693

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 694

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and chemicals that are sprayed on trees and road surfaces during other seas...

  • Page 695

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar super kleen bug and tar remover to remove. • use a high quality cleaner wax, such as mopar cleaner wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • avoi...

  • Page 696

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • use mopar touch up paint on scratches as soon as possible. Your...

  • Page 697

    Stain repel fabric cleaning procedure — if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar total clean, or a mild s...

  • Page 698

    Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Caution! Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of...

  • Page 699

    Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar glass cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or windows equipped with radio ant...

  • Page 700

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 701

    Power distribution center the power distribution center is located in the engine compartment near the battery. This center contains car- tridge fuses, micro fuses, relays, and circuit breakers. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number o...

  • Page 702

    Cavity cartridge fuse micro fuse description f06 40 amp green – anti-lock brakes/electronic stability con- trol pump f07 30 amp pink – starter solenoid f09 30 amp pink – diesel fuel heater (diesel engine only) / brake vacuum pump f10 40 amp green – body controller / exterior lighting #2 f11 30 amp p...

  • Page 703

    Cavity cartridge fuse micro fuse description f24 30 amp pink – driver door module f25 30 amp pink – front wipers f26 30 amp pink – anti-lock brakes/stability control module/valves f28 20 amp blue – trailer tow backup lights - if equipped f29 20 amp blue – trailer tow parking lights - if equipped f30...

  • Page 704

    Cavity cartridge fuse micro fuse description f40 – 10 amp red daytime running lights/headlamp lev- eling f42 – 20 amp yellow horn f44 – 10 amp red diagnostic port f49 – 10 amp red integrated central stack / climate control f50 – 20 amp yellow air suspension control module - if equipped f51 – 15 amp ...

  • Page 705

    Cavity cartridge fuse micro fuse description f59 – 10 amp red purging pump (diesel engine only) f60 – 15 amp blue transmission control module f61 – 10 amp red transmission control module/pm sensor (diesel engine only) f62 – 10 amp red air conditioning clutch f63 – 20 amp yellow ignition coils (gas),...

  • Page 706

    Cavity cartridge fuse micro fuse description f72 – 10 amp red pcm (if equipped) f73 – 15 amp blue hid headlamp rh - if equipped f75 – 10 amp red dual batt control (if equipped) f76 – 10 amp red anti-lock brakes/electronic stability con- trol f77 – 10 amp red drivetrain control module/front axle disc...

  • Page 707

    Cavity cartridge fuse micro fuse description f84 – 15 amp blue switch bank/instrument cluster f85 – 10 amp red airbag module f86 – 10 amp red airbag module f87 – 10 amp red air suspension – if equipped / trailer tow / steering column control module f88 – 15 amp blue instrument panel cluster f90/f91 ...

  • Page 708

    Cavity cartridge fuse micro fuse description f98 – 20 amp yellow front heated seats - if equipped f99 – 10 amp red climate control / driver assistance sys- tems module / dsrc f100 – 10 amp red active damping - if equipped f101 – 15 amp blue electrochromatic mirror/smart high beams - if equipped f103...

  • Page 709

    Caution! • when installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • when replacing a blown fuse,...

  • Page 710

    Replacement bulbs interior bulbs bulb number glove box lamp 194 grab handle lamp l002825w5w overhead console reading lamps vt4976 rear cargo lamp 214–2 visor vanity lamp v26377 underpanel courtesy lamps 906 instrument cluster (general illumination) 103 telltale/hazard lamp 74 708 maintaining your ve...

  • Page 711

    Exterior bulbs bulb number headlamps (low beam) - if equipped h11 premium headlamps (low/high beam) d3s (serviced at authorized dealer) headlamps (high beam) - if equipped 9005 premium park/turn signal lamp led - (service at authorized dealer) premium daytime running lamp (drl) led - (service at aut...

  • Page 712

    Bulb number rear body side tail lamps led - (service at authorized dealer) chmsl - center high mounted stop lamp led - (service at authorized dealer) note: numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized ...

  • Page 713

    Note: on vehicles equipped with high intensity dis- charge (hid) headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This dimin- ishes and becomes more white after approximately 10 seconds, as the system charges. Halogen headlamps — if equipped 1. Open the hood. 2. Turn th...

  • Page 714

    Front fog lamps 1. Reach through the cutout in the splash shield and disconnect the wiring harness from the fog lamp connector. 2. Firmly grasp the bulb by the two latches and squeeze them together to unlock the bulb from the back of the front fog lamp housing. 3. Pull the bulb straight out from the...

  • Page 715

    Rear tail, stop, and turn signal lamps 1. Raise the liftgate. 2. Remove the two push-pins from the tail lamp housing. 3. Grasp the tail lamp and pull firmly rearward to disengage the lamp from the aperture panel. 4. Twist socket counter clockwise and remove from lamp. Tail lamp push pins rear of tai...

  • Page 716

    5. Pull the bulb to remove it from the socket. 6. Replace the bulb, reinstall the socket, and reattach the lamp assembly. Rear liftgate mounted tail lamp 1. Raise the liftgate. 2. Use a fiber stick or flat blade screw driver to pry the lower trim from the liftgate. 3. Continue removing the trim. 4. ...

  • Page 717

    6. Remove/replace bulb(s). 7. Reinstall the socket(s) 8. Reverse process to reinstall the liftgate trim. Center high-mounted stop lamp (chmsl) the center high mounted stop lamp is led. Service at authorized dealer. Rear license lamp 1. The rear license lamps are led. Service at authorized dealer rea...

  • Page 718

    Fluid capacities u.S. Metric fuel (approximate) 3.6l and 5.7l engines 25 gallons 94.0 liters engine oil with filter 3.6l engine (sae 5w20, api certified) 6 quarts 5.6 liters 5.7l engine (sae 5w-20, api certified) 7 quarts 6.6 liters cooling system* 3.6l engine (mopar antifreeze/engine coolant 10 yea...

  • Page 719

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology). Engine oil – 3.6l engine we recommend you use api certified sae 5w-20 engine oil, meet...

  • Page 720

    Component fluid, lubricant, or genuine part engine oil filter we recommend you use mopar engine oil filter or equivalent. Spark plugs – 3.6l engine we recommend you use mopar spark plugs. Spark plugs – 5.7l engine we recommend you use mopar spark plugs. Fuel selection – 3.6l engine 87 octane, 0-15% ...

  • Page 721

    Caution! (continued) oat coolant (conforming to ms.90032), by an au- thorized dealer as soon as possible. • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine...

  • Page 722

    Chassis component fluid, lubricant, or genuine part automatic transmission use only mopar zf 8&9 speed atf automatic transmission fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Transfer case – single-speed (quadra-trac i) we recomme...

  • Page 723

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .722 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .724 8.

  • Page 724

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 725

    • check the fluid levels of the coolant reservoir, brake master cylinder and fill as needed. • check function of all interior and exterior lights required maintenance refer to the maintenance schedules on the following pages for required maintenance. At every oil change interval as indicated by oil ...

  • Page 726

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176...

  • Page 727

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 728

    ** the spark plug change interval is mileage based only, yearly intervals do not apply. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a servi...

  • Page 729

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .729 ▫ prepare for the appointment. . . . . . . . . . . . .729 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .729 ▫ be reasonable with requests ....

  • Page 730

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .735 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .735 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .736 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .736 728 if...

  • Page 731

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 732

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 733

    In mexico contact av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 puerto rico and u.S. Virgin islands customer service chrysler international services llc p.O. Box 191857 san juan 00919-1857 tel.: (787) 782-57...

  • Page 734

    Warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufacturer’s service contract, you will receive plan provisions and an owner identification card in the mail within three weeks of the vehicle delivery date. If you have any questions abo...

  • Page 735

    Warranty information see the warranty information booklet, located on the dvd, for the terms and provisions of fca us llc warranties applicable to this vehicle and market. Mopar parts mopar fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for...

  • Page 736

    Defect to the canadian government should contact trans- port canada, motor vehicle defect investigations and recalls at 1-800-333-0510 or go to http://www.Tc.Gc.Ca/ roadsafety/ publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. V...

  • Page 737

    Owner’s manuals these owner’s manuals have been prepared with the assistance of service and engineering specialists to ac- quaint you with specific fca us llc vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips. C...

  • Page 738

    Significantly from the norm due to variations in driving habits, service practices, and differences in road charac- teristics and climate. Traction grades the traction grades, from highest to lowest, are aa, a, b, and c. These grades represent the tire’s ability to stop on wet pavement, as measured ...

  • Page 739

    Warning! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure. 9 if you need consumer assistance 737.

  • Page 741

    Index 10

  • Page 742

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . .523 adaptive cruise control (acc) (cruise control) . . .192 adding engine coolant (antifreeze) . . . . . . . . . . . .682 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .585 additives, fuel . . . . . . . . . . . . ...

  • Page 743

    Alarm system (security alarm) . . . . . . . . . . . . . . . .20 alterations/modifications, vehicle . . . . . . . . . . . . . . .9 antifreeze (engine coolant). . . . . . . . . . . . . . .681, 716 disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .684 anti-lock brake system (abs) . . ...

  • Page 744

    Fluid check . . . . . . . . . . . . . . . . . . . . . . . . . . .687 master cylinder . . . . . . . . . . . . . . . . . . . . . . . .687 parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .521 warning light . . . . . . . . . . . . . . . . . . . . . . . . .301 brake/transmission interlo...

  • Page 745

    Installing child restraints using the vehicle seat belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 latch positions . . . . . . . . . . . . . . . . . . . . . . . .92 lower anchors and tethers for children . . . . . . .91 older children and child restraints . . . . . . . . . ...

  • Page 746

    Defroster, rear window. . . . . . . . . . . . . . . . . . . . .287 defroster, windshield . . . . . . . . . . . . . . . . . . . . . .112 dipsticks oil (engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .655 disabled vehicle towing . . . . . . . . . . . . . . . . . . . .641 disposal antifree...

  • Page 747

    Tow hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . .636 emission control system maintenance . . . . . . . . . .652 engine air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .659 block heater . . . . . . . . . . . . . . . . . . . . . . . . . .480 break-in recommendations . ....

  • Page 748

    Hazard warning . . . . . . . . . . . . . . . . . . . . . . . .616 turn signal . . . . . . . . . . . . . . . . . .114, 326, 711, 713 flooded engine starting . . . . . . . . . . . . . . . . . . . .474 fluid, brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .720 fluid capacities . . . . . ...

  • Page 749

    Garage door opener (homelink) . . . . . . . . . .253, 259 gasoline, clean air . . . . . . . . . . . . . . . . . . . . . . . .580 gasoline (fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . .579 gasoline, reformulated . . . . . . . . . . . . . . . . . . . . .580 gear ranges . . . . . . . . . ...

  • Page 750

    Interior appearance care . . . . . . . . . . . . . . . . . . . .695 intermittent wipers (delay wipers). . . . . . . . . . . . .180 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 inverter, power . . . . . . . . . . . . . . . . . . . . . . . . . . .274 ipod control. . . . . ...

  • Page 751

    Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 liftgate window wiper/washer . . . . . . . . . . . . . . .286 light bulbs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114, 168 air bag . . ...

  • Page 752

    Vanity mirror . . . . . . . . . . . . . . . . . . . . . . . . . .134 warning (instrument cluster description) . . .304, 326 loading vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .588 tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .552 locks . . . . . . . . . . . . . ...

  • Page 753

    Octane rating, gasoline (fuel) . . . . . . . . . . . . . . . .579 off-pavement driving (off-road) . . . . . . . . . . . . . .510 off-road driving (off-pavement) . . . . . . . . . . . . . .510 oil, engine . . . . . . . . . . . . . . . . . . . . . . .336, 655, 717 capacity . . . . . . . . . . . . . . ...

  • Page 754

    Power brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .523 distribution center (fuses) . . . . . . . . . . . . . . . .699 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .274 lift gate . . . . ...

  • Page 755

    Rear cupholder . . . . . . . . . . . . . . . . . . . . . . . . . .276 rear parksense system . . . . . . . . . . . . . . . . . .223, 235 rear seat, folding . . . . . . . . . . . . . . . . . . . . . . . . .159 rear window features . . . . . . . . . . . . . . . . . . . . .286 rear wiper/washer. . . . ....

  • Page 756

    Safety defects, reporting . . . . . . . . . . . . . . . . . . . .733 safety, exhaust gas . . . . . . . . . . . . . . . . . . . . . . . .111 safety information, tire . . . . . . . . . . . . . . . . . . . . .545 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 schedule, maint...

  • Page 757

    Vented . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 ventilated . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 security alarm. . . . . . . . . . . . . . . . . . . . . . . . .20, 303 arm the system . . . . . . . . . . . . . . . . . . . . . . . .21 disarm the system . ...

  • Page 758

    Steering power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .519 tilt column . . . . . . . . . . . . . . . . . . . . . . . .184, 185 wheel, heated . . . . . . . . . . . . . . . . . . . . . . . . .187 wheel, tilt . . . . . . . . . . . . . . . . . . . . . . . . .184, 185 steering wheel ...

  • Page 759

    Pressure warning light . . . . . . . . . . . . . . . . . . .314 quality grading . . . . . . . . . . . . . . . . . . . . . . . .735 radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .560 replacement . . . . . . . . . . . . . . . . . . . . . . .568, 629 rotation . . . . . . . . . . . ...

  • Page 760

    Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .690 shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .480 transmitter battery service (remote keyless entry) . .26 transmitter, garage door opener (homelink) . . . . .253 transmitter programming (remote keyless entry)...

  • Page 761

    Vehicle storage. . . . . . . . . . . . . . . . . . . . . . . .440, 707 viscosity, engine oil . . . . . . . . . . . . . . . . . . . . . . .657 voice recognition system (vr) . . . . . . . . . . . . . . . .443 warning flasher, hazard . . . . . . . . . . . . . . . . . . . .616 warning, roll over . . . ....

  • Page 763

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 764

    Grand cherokee o w n e r ’ s m a n u a l 20 16 gr and cher ok ee first edition rev 1 printed in u.S.A. 16wk741-126-aa ©2015 fca us llc. All rights reserved. Jeep is a registered trademark of fca us llc. 2 0 1 6 stick with the specialists ®.