1. DL manuals
  2. Jeep
  3. Automobile
  4. 2016 Patriot
  5. Owner's Manual

Jeep 2016 Patriot Owner's Manual

Other manuals for 2016 Patriot: User Manual, Owner's Manual

Summary of 2016 Patriot

  • Page 1

    Patriot o w n e r ’ s m a n u a l 2 0 1 6.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engine...

  • Page 7

    Control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the unive...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 sentry k...

  • Page 12

    ▫ sound horn with remote key lock . . . . . . . . .22 ▫ flash lights with remote key lock/unlock . . .23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . .24 ▫ programming additional transmitters. . . . . . . .24 ▫ transmitter battery replacement . . . . . . . . . . .24 ▫ general informatio...

  • Page 13

    ▫ important safety precautions . . . . . . . . . . . . . .39 ▫ seat belt systems . . . . . . . . . . . . . . . . . . . . . .41 ▫ supplemental restraint system (srs) . . . . . . . .60 ▫ child restraints . . . . . . . . . . . . . . . . . . . . . . .75 ▫ transporting pets . . . . . . . . . . . . . . . ...

  • Page 14

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 15

    Note: if you try to remove the key before you place the shift lever in park, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in park, rotate the key clockwise slightly, and then remove the key as described above. If a malfunction occurs...

  • Page 16

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the key fob in or near th...

  • Page 17

    Sentry key the sentry key immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded elec...

  • Page 18

    Caution! The sentry key immobilizer system is not compat- ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics. ...

  • Page 19

    Customer key programming if you have two valid sentry keys, you can program new sentry keys to the system by performing the following procedure: 1. Cut the additional sentry key transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition ...

  • Page 20

    Note: if a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of s...

  • Page 21

    To arm the system 1. Remove the key from the ignition switch and get out of the vehicle. 2. Lock the door using either the power door lock switch or the remote keyless entry (rke) transmitter and close all doors. 3. The vehicle security light in the instrument cluster will flash rapidly for approxim...

  • Page 22

    Once the vehicle security alarm is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, push the unlock button on the rke transmitter to disarm the vehicle security alarm. Vehicle security alarm manual override the vehicle security alarm will not arm...

  • Page 23

    Within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote key unlock, driver door/all first press this feature lets you program the system to unlock either the driver’s door or all ...

  • Page 24

    Illuminated approach — if equipped this feature activates the headlights for up to 90 seconds when the doors are unlocked with the rke transmitter. The time for this feature is programmable on vehicles equipped with the evic. Refer to “electronic vehicle information center (evic)/personal settings (...

  • Page 25

    3. Test the feature while outside of the vehicle by pushing the lock button on the rke transmitter with the ignition switch in the lock position and the key removed. 4. Repeat these steps if you want to return this feature to its previous setting. Note: pushing the lock button on the rke transmitter...

  • Page 26

    4. Repeat these steps if you want to return this feature to its previous setting. Note: pushing the lock button on the rke transmitter while you are in the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Push t...

  • Page 27

    Two halves of the rke transmitter apart. Make sure not to damage the elastomer seal during removal. 2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble ...

  • Page 28

    Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the...

  • Page 29

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Carbon monoxide is poisonous and can cause serious in- jury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 30

    Note: • the park lamps will turn on and remain on during remote start mode. • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the remote start mode. • if your power door locks were unlocked, remote start will automatically lock the doors. • ...

  • Page 31

    To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, push and release the unlock button on the rke transmitter to unlock the doors and disarm the vehicle security alarm (if equipped). Then, insert the key into the ignition switch and turn the switch to the on/run po...

  • Page 32

    Warning! • for personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. (continued) warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in ...

  • Page 33

    Power door locks a power door lock switch is located on the driver’s and front passenger’s door panel. Push this switch to lock or unlock the doors and liftgate. Note: to prevent from locking the key in the vehicle, the power door lock switch will not operate when the key is in the ignition and eith...

  • Page 34

    Auto lock doors — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). Auto lock doors programming the automatic door locks feature can be enabled or disabled as follows: • for veh...

  • Page 35

    Automatic unlock doors on exit the doors will unlock automatically if: • the automatic unlock doors on exit feature is en- abled. • the transmission was in gear, and the vehicle speed returned to 0 mph (0 km/h). • the transmission is in neutral or park. • the driver’s door is opened. • the doors wer...

  • Page 36

    Note: • if you do not hear the chime, it means that the system did not enter the programming mode and you will need to repeat the procedure. • use the automatic unlock doors on exit feature in accordance with local laws. Child-protection door lock system — rear doors to provide a safer environment f...

  • Page 37

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: for emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window, and open the do...

  • Page 38

    • for vehicles equipped with the evic, the power window switches will remain active for up to 10 minutes after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “electronic vehicle information c...

  • Page 39

    Window lockout switch the window lockout switch on the driver’s door allows you to disable the window controls on the rear passenger doors. To disable the window controls on the rear pas- senger doors, push the window lockout switch. To enable the rear window controls, push the window lockout switch...

  • Page 40

    Liftgate note: the key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn to the right (manual lock models only). The liftgate can also be unlocked using the remote keyless entry (rke) transm...

  • Page 41

    Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are c...

  • Page 42

    Here are some simple steps you can take to minimize the risk of harm from a deploying air bag: 1. Children 12 years old and under should always ride buckled up in a vehicle with a rear seat. 2. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger ...

  • Page 43

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 44

    Position the seat belt reminder light will turn on and remain on until both outboard front seat belts are buck- led. The outboard front passenger seat beltalert is not active when an outboard front passenger seat is unoccu- pied. Beltalert warning sequence the beltalert warning sequence is activated...

  • Page 45

    Beltalert can be activated or deactivated by your autho- rized dealer. Fca us llc does not recommend deacti- vating beltalert. Note: if beltalert has been deactivated and the driver or outboard front seat passenger (if equipped with out- board front passenger seat beltalert) is unbuckled the seat be...

  • Page 46

    Warning! (continued) • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • ...

  • Page 47

    Warning! (continued) • a seat belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing inter- nal injuries. Always buckle your seat belt into the buckle nearest you. • a seat belt that is too loose will not protect y...

  • Page 48

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the sea...

  • Page 49

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 50

    6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Lap/shoulder belt untwisting procedure use the following procedure to untwist...

  • Page 51

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 52

    1. Remove the mini-latch plate and regular latch plate from its stowed position in the right rear side trim panel. 2. Grasp the mini-latch plate and pull the seat belt over the seat. 3. Route the shoulder belt to the inside of the right head restraint. 4. When the seat belt is long enough to fit, in...

  • Page 53

    8. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retrac- tor will withdraw any slack in the seat belt. 9. To release the seat belt, push the red button on the buckle. 10. To disengage the mini-latch plate from the mini- buckle for storage, inser...

  • Page 54

    Warning! • if the mini-latch plate and mini-buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide (continued) warning! (continued) proper restraint and will increase the risk of injury in a collision. • when reattaching the mini-latch ...

  • Page 55

    Seat belt extender is not required for a different occu- pant, it must be removed. Warning! • only use a seat belt extender if it is physically required in order to properly fit the original seat belt system. Do not use the seat belt extender if, when worn, the distance between the front edge of the...

  • Page 56

    Position the lap belt snug and low below the abdomen and across the strong bones of the hips. Place the shoulder belt across the chest and away from the neck. Never place the shoulder belt behind the back or under the arm . Seat belt pretensioner the front seat belt system is equipped with pretensio...

  • Page 57

    Restraints” section of this manual. The table below defines the type of feature for each seating position. If the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-sectio...

  • Page 58

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 59

    Warning! (continued) only used to install rear-facing or forward-facing child restraints that have a harness for restraining the child. Supplemental active head restraints (ahr) these head restraints are passive, deployable compo- nents, and vehicles with this equipment cannot be readily identified ...

  • Page 60

    Warning! • all occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. • do not place items over the top of the active head restra...

  • Page 61

    Warning! (continued) as loose cargo could contact the active head re- straint during sudden stops. Failure to follow this warning could cause personal injury if the active head restraint is deployed. Note: for more information on properly adjusting and positioning the head restraint, refer to “adjus...

  • Page 62

    Warning! Deployed ahrs are not able to best protect you in all types of collisions. Have deployed ahrs reset by an authorized dealer immediately. Supplemental restraint system (srs) air bag system components your vehicle may be equipped with the following air bag system components: • occupant restra...

  • Page 63

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 64

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 65

    Warning! (continued) • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, air bags won’t deploy at all. Al- ways wear your seat belts even though you have air bags. Advanced front air ba...

  • Page 66

    Way as the air bags inflate to their full size. The advanced front air bags fully inflate in less time than it takes to blink your eyes. The air bags then quickly deflate while helping to restrain the driver and front passenger. Knee impact bolsters the knee impact bolsters help protect the knees of...

  • Page 67

    The sabs may help to reduce the risk of occupant injury during certain side impacts and/or vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. When the sab deploys, it opens the seam on the outboard side of the seatback’s trim cover. ...

  • Page 68

    Sabics may help reduce the risk of head or other injuries to front and rear seat outboard occupants in certain side impacts and/or vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. The sabics deploy downward, covering the side win- ...

  • Page 69

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 70

    Warning! (continued) properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note: air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. Side impacts in side impacts, the side impa...

  • Page 71

    Faster-developing event may deploy the seat belt preten- sioners as well as the side air bags on both sides of the vehicle. The rollover sensing-system may also deploy the seat belt pretensioners, with or without the side air bags, on both sides of the vehicle if the vehicle experiences a near rollo...

  • Page 72

    Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and th...

  • Page 73

    Enhanced accident response system reset procedure in order to reset the enhanced accident response system functions after an event, the ignition switch must be changed from ignition start or on/run to ignition off. Carefully check the vehicle for fuel leaks in the engine compartment and on the groun...

  • Page 74

    While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • the air bag warning light does not come on during the four to eight seconds when the ignition switch is first turned to the on/run position...

  • Page 75

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 76

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 77

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 78

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in...

  • Page 79

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 80

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 81

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 82

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 83

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 84

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 85

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to know before starting your vehicle 83.

  • Page 86

    Frequently asked questions about installing child seats with latch what is the weight limit (child’s weight + weight of the child restraint) for us- ing the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child an...

  • Page 87

    Frequently asked questions about installing child seats with latch can two child restraints be attached using a common lower latch anchor- age? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat be...

  • Page 88

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the ...

  • Page 89

    Locating tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower ancho...

  • Page 90

    Restraints with flexible, webbing mounted lower attach- ments can be installed in any rear seating position. Warning! Never use the same lower anchorage to attach more than one child restraint. If you are installing latch- compatible child restraints next to each other, you must use the seat belt fo...

  • Page 91

    3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 92

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 93

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • top tether anchorage symbol 2 things to know before starting your vehicle 91.

  • Page 94

    Frequently asked questions about installing child restraints with seat belts what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a for- ward facing child restraint? Weight limit of the child restraint always use the tet...

  • Page 95

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 96

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 97

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 98

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 99

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 100

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 101

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 102

    Unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • alwa...

  • Page 103

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 105: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 ▫ inside day/night mirror . . . . . . . . . . . . . . . .108 ▫ automatic dimming mirror — if equipped . . .108 ▫ outside mirror — driver side . . . . . . . . . . . .109 ▫ outside ...

  • Page 106

    䡵 voice command — if equipped . . . . . . . .143 ▫ voice command system operation . . . . . . . . .143 ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . .145 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . .149 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 107

    ▫ headlights on with wipers (available with automatic headlights only) . . . . . . . . . . . . .168 ▫ instrument panel dimming. . . . . . . . . . . . . . .168 ▫ map/reading lights . . . . . . . . . . . . . . . . . . .169 䡵 windshield wipers and washers . . . . . .170 ▫ windshield wiper operation . ....

  • Page 108

    ▫ using homelink . . . . . . . . . . . . . . . . . . . . .189 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . .189 ▫ troubleshooting tips . . . . . . . . . . . . . . . . . . .189 ▫ general information. . . . . . . . . . . . . . . . . . . .190 䡵 power sunroof — if equipped . . . . . ...

  • Page 109

    ▫ cargo tie-down loops . . . . . . . . . . . . . . . . .206 ▫ fold down speakers — if equipped . . . . . . . .207 䡵 rear window features . . . . . . . . . . . . . .208 ▫ rear window wiper/washer . . . . . . . . . . . . .208 ▫ rear window defroster . . . . . . . . . . . . . . . . .209 䡵 roof luggage ...

  • Page 110

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 111

    Note: this feature is disabled when the vehicle is moving in reverse. Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside mirror — driver side adjust the flat outs...

  • Page 112

    Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or...

  • Page 113

    To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror. Heated mirro...

  • Page 114

    Sun visor “slide-on-rod” feature — if equipped the sun visors may be extended out to provide more coverage of the side glass. Uconnect phone — if equipped uconnect phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect phone allows you to dial a phone number with your mo...

  • Page 115

    Uconnect phone. The uconnect phone allows up to seven mobile phones to be linked to the system. Only one linked (or paired) mobile phone can be used with the system at a time. The system is available in english, spanish, or french languages. Warning! Any voice commanded system should be used only in...

  • Page 116

    Adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if equipped. The radio display will be used for visual prompts from the uconnect phone such as “cell” or caller id on certain radios. Operation voice commands can be used to operate the uconne...

  • Page 117

    Voice command tree refer to “voice tree” in this section. Help command if you need assistance at any prompt, or if you want to know your options at any prompt, say “help” following the beep. The uconnect phone will play some of the options at any prompt if you ask for help. To activate the uconnect ...

  • Page 118

    You will be asked to say a four-digit personal identifica- tion number (pin), which you will later need to enter into your mobile phone. You can enter any four-digit pin. You will not need to remember this pin after the initial pairing process. For identification purposes, you will be prompted to gi...

  • Page 119

    Call by saying a name • push the phone button to begin. • after the “ready” prompt and the following beep, say “call.” • the system will prompt you to say the name of the person you want to call. • after the “ready” prompt and the following beep, say the name of the person you want to call. For exam...

  • Page 120

    5. When prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The uconnect phone will allow you to ent...

  • Page 121

    Downloaded names can be used. Until then, if avail- able, the previously downloaded phonebook is avail- able for use. • only the phonebook of the currently connected mobile phone is accessible. • either the mobile phone’s phonebook or the mobile phone’s sim card phonebook is downloaded. • this downl...

  • Page 122

    Mobile and a home number, but you can add “john doe’s” work number later using the “phonebook edit” feature. Delete uconnect phonebook entry note: editing phonebook entries is recommended when the vehicle is not in motion. To delete a uconnect phonebook entry using voice com- mands: 1. Push the phon...

  • Page 123

    Delete/erase “all” uconnect phonebook entries to delete, or erase all uconnect phonebook entries using voice command: 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say “phonebook erase all.” • the uconnect phone will ask you to verify that you wish to delete ...

  • Page 124

    Phone call features the following features can be accessed through the uconnect phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the uconnect phone. Check with your mobile serv...

  • Page 125

    Entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to “toggling between calls” in this section. To combine two calls, refer to “conference call” in this section. Place/retrieve a call from hold to put a call on hold: 1. Pu...

  • Page 126

    Phone button until you hear a double beep, indi- cating that the two calls have been joined into one conference call. Call termination to end a call in progress: 1. Momentarily push the phone button. • only the active call(s) will be terminated and if there is a call on hold, it will become the new ...

  • Page 127

    Call continuation call continuation is the progression of a phone call on the uconnect phone after the vehicle ignition has been switched to off. Call continuation functionality avail- able on the vehicle can be any one of three types: 1. After the ignition is switched to off, a call can continue on...

  • Page 128

    Emergency assistance if you are in an emergency and the mobile phone is reachable: • pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the uconnect phone is operational, you may reach the emergency number as follows: • push the phone button to ...

  • Page 129

    Warning! To use your uconnect phone system in an emergency, your mobile phone must be: • turned on. • paired to the uconnect system. • have network coverage. Roadside assistance/towing assistance if you need roadside assistance: • push the phone button to begin. • after the “ready” prompt and the fo...

  • Page 130

    Working with automated systems this method is used in instances where one generally has to push numbers on the mobile phone keypad while navigating through an automated telephone system. You can use your uconnect phone to access a voice mail system or an automated service, such as a paging service o...

  • Page 131

    Barge in — overriding prompts the “voice command” button can be used when you wish to skip part of a prompt and issue your voice command immediately. For example, if a prompt is asking “would you like to pair a phone, clear a...,” you could push the voice command button and say, “pair a phone” to se...

  • Page 132

    Note: certain brands of mobile phones do not send the dial ring to the uconnect phone to play it on the vehicle audio system, so you will not hear it. Under this situa- tion, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress. O...

  • Page 133

    Connect or disconnect link between the uconnect phone and mobile phone your mobile phone can be paired with many different electronic devices, but can only be actively “connected” with one electronic device at a time. If you would like to connect or disconnect the bluetooth connection between your m...

  • Page 134

    • the selected phone will be used for the next phone call. If the selected phone is not available, the uconnect phone will return to using the highest priority phone present in or near (approximately within 30 ft. [9 m]) the vehicle. Delete uconnect phone paired mobile phones to delete mobile phones...

  • Page 135

    • push the voice command button and say the “voice training,” “system training,” or “start voice training” command. You can either push the uconnect phone button to restore the factory setting or repeat the words and phrases when prompted by the uconnect phone. For best results, the voice training s...

  • Page 136

    Performance is maximized under: • low-to-medium blower setting • low-to-medium vehicle speed • low road noise • smooth road surface • fully closed windows • dry weather condition note: • even though the system is designed for users speaking in north american english, french, and spanish ac- cents, t...

  • Page 137

    Far end audio performance audio quality is maximized under: • low-to-medium blower setting • low-to-medium vehicle speed • low road noise • smooth road surface • fully closed windows • dry weather conditions • operation from the driver’s seat • performance, such as audio clarity, echo, and loudness ...

  • Page 138

    3. Uconnect phone will play the new text message for you. After reading a message, you can “reply” or “forward” the message using uconnect phone. Send messages: you can send messages using uconnect phone. To send a new message: 1. Push the phone button. 2. After the “ready” prompt and the following ...

  • Page 139

    11. See you in 15 minutes. 12. I am on my way. 13. I’ll be late. 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now. 18. When can we meet? 19. Send number to call. 20. Start without me. Turn voice text reply incoming announcement on/off turning the voice text reply i...

  • Page 140

    138 understanding the features of your vehicle.

  • Page 141

    3 understanding the features of your vehicle 139.

  • Page 142

    140 understanding the features of your vehicle.

  • Page 143

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help 3 understanding the features...

  • Page 144

    Primary alternate (s) home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again primary alternate (s) redial return to main menu return or main menu select phone select send set up phone settings or phon...

  • Page 145

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 146

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When y...

  • Page 147

    To hear the first available menu, push the voice com- mand button and say “help” or “main menu.” commands the voice command system understands two types of commands, universal commands and local commands. Universal commands are available at all times. Local commands are available if the supported ra...

  • Page 148

    Radio am to switch to the am band, say “am” or “radio am.” in this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “m...

  • Page 149

    Disc mode to switch to the disc mode, say “disc.” in this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) usb mode to switch to usb mode, s...

  • Page 150

    Memo mode to switch to the voice recorder mode, say “memo.” in this mode, you may say the following commands: • “new memo” (to record a new memo) — during the recording, you may push the voice command but- ton to stop recording. You proceed by saying one of the following commands: – “save” (to save ...

  • Page 151

    • “tutorial” • “voice training” note: keep in mind that you have to push the voice command button first and wait for the beep before speaking the “barge in” commands. Voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers the uconnect voice “vo...

  • Page 152

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • be sure everyone in your vehicle is in a seat and using a seat belt properl...

  • Page 153

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 154

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the center instrument panel area. You can choose from hi, lo or off heat settings. Amber indica...

  • Page 155

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Man...

  • Page 156

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 157

    Manual lumbar — if equipped the lumbar adjustment handle is located on the inboard or outboard side of the seatback. Rotate the lever down- ward to increase the lumbar support or rotate the lever upward to decrease the lumbar support. Driver’s seatback recline to adjust the seatback, lift the lever ...

  • Page 158

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Head restraints head restraints are designed to reduce the risk of injury by restricti...

  • Page 159

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 160

    For comfort the active head restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Note: • the head ...

  • Page 161

    • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head restraints (ahr)” in “things to know before starting your vehicle” for further information. Warning! • all occupants, including the driver, should not operate a vehicle or sit in a vehicle...

  • Page 162

    Folding rear seat to provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to fold the rear seatback flat. To raise the seatback, pull the strap forward and lift the seatback into its upright position. Rear seat release straps folded rear seat 160 understa...

  • Page 163

    Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Reclining rear seat — if equipped for ...

  • Page 164

    To open and close the hood to open the hood, two latches must be released. 1. Pull the hood release lever located on the left kick panel. 2. Move the safety catch located under the front edge of the hood, near the center and raise the hood. Hood release lever hood safety latch location 162 understan...

  • Page 165

    Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment, to secure the hood in the open position. Place the hood prop at the location stamped into the inner hood surface. Caution! To prevent possible damage: • before closing hood, make sure the hood prop r...

  • Page 166

    Lights multifunction lever the multifunction lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and the fog lights. The multifunction lever is located on the left side of the ste...

  • Page 167

    Headlights and parking lights turn the end of the multifunction lever to the first detent to turn on the parking lights. Turn the end of the lever to the second detent to turn on the headlights. Automatic headlights — if equipped turning the end of the multifunction lever to the third detent (auto),...

  • Page 168

    With the engine running and the multifunction lever in the auto position, the headlights will turn on and turn off based on the surrounding light levels. Daytime running lights — if equipped the high beam lights will come on as daytime running lights (lower intensity), whenever the ignition is on, t...

  • Page 169

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside l...

  • Page 170

    Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will turn on the high beam headlights until the lever is released. Note: if the multifunction lever is held in the flash-to- pass position for more than 20 seconds, the high ...

  • Page 171

    Rotate the center portion of the lever upward to the last detent to turn on the interior lighting. Map/reading lights these lights are mounted between the sun visors above the rear view mirror. Each light is turned on by pushing the button. Push the button a second time to turn the light off. The li...

  • Page 172

    Note: the lights will remain on until the switch is pushed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically. Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column...

  • Page 173

    Caution! • turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • in cold weather, always turn off the wiper switch and allow the wipers to return to the “park” posi- tion be...

  • Page 174

    Intermittent wiper system use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Select the delay interval by turning the end of the lever. Rotate the end of the lever upward (clockwise) to decrease the delay time and downwar...

  • Page 175

    If the headlight switch is placed in the auto position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. Note: the headlights on with wipers feature can be turned on or off using the electronic vehicle information center (evic). Refer t...

  • Page 176

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt steering column lever is located on the left side of the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering whee...

  • Page 177

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 178

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 179

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate the electronic speed control with- out erasing the set speed from memory. Pushing the on/off button or turning the ignition switch off erases the set speed from ...

  • Page 180

    • if the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed will be established. To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The drivers preferred units can...

  • Page 181

    Using electronic speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so...

  • Page 182

    Out of reverse unless the forward vehicle speed ex- ceeds 8 mph (13 km/h), the transmission is shifted into ⬙ park ⬙ or the vehicles ignition is cycled to the off position. Static grid lines will illustrate the width of the vehicle. The static grid lines will show separate zones that will help indic...

  • Page 183

    Caution! • to avoid vehicle damage, parkview should only be used as a parking aid. The parkview camera is unable to view every obstacle or object in your drive path. • to avoid vehicle damage, the vehicle must be driven slowly when using parkview to be able to stop in time when an obstacle is seen. ...

  • Page 184

    Homelink buttons/sunvisor/headliner note: homelink is disabled when the vehicle security alarm is active. Homelink buttons/overhead consoles 182 understanding the features of your vehicle.

  • Page 185

    Before you begin programming homelink be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the de...

  • Page 186

    1. Place the ignition in the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink button you wish to program while keeping the homelink indicator light in view. 3. Push and hold the homelink button you want to program while you push and hold the hand-h...

  • Page 187

    Firmly push and release the “learn” or “train- ing” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the learn/train mode. Note: you have 30 seconds in which to initiate the next step after the learn button has been pushed. 6. Retu...

  • Page 188

    Programming a non-rolling code for programming garage door openers manufactured before 1995. 1. Place the ignition in the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink button you wish to program while keeping the homelink indicator light in view...

  • Page 189

    3. Without releasing the button proceed with “program- ming a non-rolling code” step 2 and follow all remaining steps. Canadian/gate operator programming for programming transmitters in canada/united states that require the transmitter signals to “time-out” after several seconds of transmission. Can...

  • Page 190

    4. Watch for the homelink indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you are programming. 5. Push and hold the programmed homelink button and observe the indicator light. Note: • i...

  • Page 191

    Using homelink to operate, push and release the programmed homelink button. Activation will now occur for the programmed device (i.E. Garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.) the hand-held transmitter of the device may also be used at any time....

  • Page 192

    Warning! • vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while programming the transceiver. Exhaust gas can cause serious injury or death. • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do ...

  • Page 193

    Power sunroof — if equipped the power sunroof switch is located on the overhead console. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly unat-...

  • Page 194

    Opening sunroof — express push the switch rearward and release it within one-half second. The sunroof and sunshade will open automati- cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “express open.” during express open operation, any other act...

  • Page 195

    Venting sunroof — express push and release the vent button within one half second and the sunroof will open to the vent position. This is called “express vent”, and it will occur regardless of sunroof position. During express vent operation, any other actuation of the switch will stop the sunroof. S...

  • Page 196

    For vehicles equipped with the evic the power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. Electrical power outlets there is a standard 12 volt (13 amp) power outlet...

  • Page 197

    Note: to ensure proper operation a mopar knob and element must be used. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • power outlets are designed for accessory...

  • Page 198

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 199

    The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximat...

  • Page 200

    Warning! To avoid serious injury or death: • do not use a three-prong adaptor. • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories tha...

  • Page 201

    Cupholders your vehicle is equipped with four cupholders. There are two illuminated cupholders located in the front. There are two cupholders located in the back for the rear passengers. Front cupholders rear cupholders 3 understanding the features of your vehicle 199.

  • Page 202

    Storage glove compartment and storage bin located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. Storage bins 1 — upper storage bin 2 — lower glove compartment 200 understanding the features of your vehicle.

  • Page 203

    To open the lower glove compartment, pull outward on the release handle. Door storage the interior door panels are equipped with lower storage areas. Glove compartment front door storage 3 understanding the features of your vehicle 201.

  • Page 204

    Console features the floor console contains both an upper and lower storage compartment. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. To open the lower storage compartment, lift upward on the lower handle to unlatch the lower ...

  • Page 205

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Cargo area features cargo light the light is mounted in the headliner above the cargo area to illuminate the cargo area. Carg...

  • Page 206

    To install the cargo cover, insert either end of the cover into one of the two notches located in the rear trim panels. With one of the cover ends installed, push inward on the opposite end and install it into the same notch location of the rear trim panel. Using the handle, pull the cover toward yo...

  • Page 207

    Warning! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. Do...

  • Page 208

    Cargo tie-down loops there are four tie-downs (d-rings) installed in the cargo area for securing cargo. Warning! • cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be b...

  • Page 209

    Warning! (continued) • place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be...

  • Page 210

    Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the center portion of the control lever. The control lever is located on the right side of the steering column. Rotate the center portion of the lever upward to the first detent position f...

  • Page 211

    Note: the rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to operate as long as the switch is held (for a maximum of 10 seconds). Upon release, the wiper will conti...

  • Page 212

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 213

    The crossbars must also be secured in one of the seven detent positions marked with an arrow on the siderails to prevent movement. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately eight turns, then move the crossbar to the desired position, keep...

  • Page 214

    Caution! (continued) • long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof ra...

  • Page 215: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .217 䡵 instrument cluster . . . . . . . . . . . . . . . . .218 䡵 warning and indicator lights . . . . . . .223 ▫ red telltale indicator lights . . . . . . . . . . . . . .224 ▫ yellow telltale indicator lights ...

  • Page 216

    ▫ display units of measure in . . . . . . . . . . . . .254 䡵 personal settings (customer-programmable features) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .254 ▫ language . . . . . . . . . . . . . . . . . . . . . . . . . . .254 ▫ auto lock doors . . . . . . . . . . . . . . . . . . . . ....

  • Page 217

    ▫ info button — disc mode for mp3/wma play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .274 ▫ uconnect (satellite radio) — if equipped . . . .276 䡵 uconnect 430/430n cd/dvd/hdd/nav — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .280 ▫ operating instructions (voice comm...

  • Page 218

    ▫ list or browse mode . . . . . . . . . . . . . . . . . . .310 ▫ bluetooth streaming audio (btsa) . . . . . . . . .312 䡵 steering wheel audio controls . . . . . .313 ▫ radio operation . . . . . . . . . . . . . . . . . . . . . .314 ▫ cd player . . . . . . . . . . . . . . . . . . . . . . . . . . .314 ...

  • Page 219

    Instrument panel features 1 — air outlet 5 — storage bin 9 — heated seat switch – if equipped 2 — demisters 6 — glove compartment 10 — hazard warning flasher 3 — instrument cluster 7 — climate controls 11 — esc off switch – if equipped 4 — radio 8 — power outlet 12 — heated seat switch – if equipped...

  • Page 220

    Instrument cluster 218 understanding your instrument panel.

  • Page 221

    1. Speedometer • the speedometer shows the vehicle speed in miles per hour (mph) and kilometers per hour (km/h). Odometer display / trip odometer display this display indicates the total distance the vehicle has been driven. Note: u.S. Federal regulations require that upon trans- fer of vehicle owne...

  • Page 222

    Caution! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h”, turn the engine ...

  • Page 223

    Message display area when the appropriate conditions exist, the following odometer messages will display: door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door ajar gate . . . . . . . . . . . . . . . . . . . . . . . . . . Liftgate ajar low tire . . . . . . . . . . . . . . . . . . . . L...

  • Page 224

    Damaged, a “nofuse” message will display in the odom- eter display area. Refer to “fuses” in “maintaining your vehicle” for further information on fuses and fuse loca- tions. Change oil your vehicle is equipped with an engine oil change indicator system. The odometer display will toggle be- tween ch...

  • Page 225

    Warning and indicator lights important: the warning / indicator light switches on in the instrument panel together with a dedicated mes- sage and/or acoustic signal when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative...

  • Page 226

    Red telltale indicator lights seat belt reminder warning light red telltale light what it means seat belt reminder warning light when the ignition switch is first turned to on/run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is ...

  • Page 227

    Air bag warning light red telltale light what it means air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspe...

  • Page 228

    Brake warning light red telltale light what it means united states canada brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid le...

  • Page 229

    The light will remain on until the cause is corrected. Note: the light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces...

  • Page 230

    Vehicle security warning light — if equipped red telltale light what it means vehicle security warning light this light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. Oil pressure warning lig...

  • Page 231

    Engine temperature warning light red warning light what it means engine temperature warning light this light warns of an overheated engine condition. As engine coolant temperatures rise and the gauge approaches h, this indicator will illuminate and a single chime will sound after reaching a set thre...

  • Page 232

    Oil temperature warning light red telltale light what it means oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Charging system warning light red telltale light wha...

  • Page 233

    Red telltale light what it means if jump starting is required, refer to “jump starting procedures” in “what to do in emer- gencies.” electronic throttle control (etc) warning light red telltale light what it means electronic throttle control (etc) warning light this light informs you of a problem wi...

  • Page 234

    Red telltale light what it means run and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. Yellow telltale indicator lights engine check/malfunction indicator light (mil) yellow telltale light what it means engine check...

  • Page 235

    Yellow telltale light what it means certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through sev- eral typical driving styles. In most situations, the vehicle will drive ...

  • Page 236

    Tire pressure monitoring indicator light yellow telltale light what it means tire pressure monitoring indicator light the warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these ...

  • Page 237

    Important: do not continue driving with one or more flat tires as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. Repair immediately using the dedicated tire repair kit and contact your authorized dealership as soon as possible. Each tire, including the spare (if ...

  • Page 238

    Illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur for a variety of reasons, includi...

  • Page 239

    Electronic stability control (esc) off indicator light — if equipped yellow telltale light what it means electronic stability control (esc) off indicator light this light indicates the electronic stability control (esc) is off. 4 understanding your instrument panel 237.

  • Page 240

    Electronic stability control (esc) indicator light — if equipped yellow telltale light what it means electronic stability control (esc) indicator light the “esc indicator light” in the instrument cluster will come on when the ignition switch is turned to the on/run position. It should go out with th...

  • Page 241

    Anti-lock brake (abs) indicator light yellow telltale light what it means anti-lock brake (abs) indicator light this light monitors the anti-lock brake system (abs). The light will turn on when the igni- tion switch is placed in the on/run position and may stay on for as long as four seconds. If the...

  • Page 242

    Low fuel warning indicator light yellow telltale light what it means low fuel warning indicator light when the fuel level reaches approximately 2.8 gal (10.6 l), this light will turn on and a single chime will sound. 4wd! Warning light — if equipped yellow tell- tale light what it means 4wd! Warning...

  • Page 243

    Loose fuel filler cap indicator light — if equipped yellow telltale light what it means loose fuel filler cap indicator light this light will illuminate when fuel filler cap is loose. Properly close the filler cap to disen- gage the light. If the light does not turn off, please see your authorized d...

  • Page 244

    Transmission temperature indicator light red telltale light what it means transmission temperature indicator light this light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and stop ...

  • Page 245

    Green telltale indicator lights turn signal indicator lights green tell- tale light what it means turn signal indicator lights the instrument cluster arrow will flash independently for the left or right turn signal as se- lected, as well as the exterior turn signal lamp(s) (front and rear) as select...

  • Page 246

    Park/headlight on indicator light green telltale light what it means park/headlight on indicator light this indicator will illuminate when the park lights or headlights are turned on. Front fog indicator light — if equipped green telltale light what it means front fog indicator light this indicator ...

  • Page 247

    Blue telltale indicator light high beam indicator light blue telltale light what it means high beam indicator light this indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch...

  • Page 248

    Hill descent indicator light — if equipped white tell- tale light what it means hill descent indicator light this indicator shows when the hill descent control (hdc) feature is turned on. The lamp will be on solid when hdc is armed. Hdc can only be armed when the transfer case is in the “4wd low” po...

  • Page 249

    Control buttons step button push the step button located on the steering wheel to scroll through sub menus (i.E., temperature, trip func- tions: odometer, trip a, trip b). Reset button to reset the display shown, turn the ignition switch to the on position, then push and hold the reset button locate...

  • Page 250

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • units • vehicle information warning message displays • ...

  • Page 251

    The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: menu button push and release the menu button to scroll through the main menus (fuel economy, warn- ings, timer, units, system, personal settings) or to exit submenus. Compass button pus...

  • Page 252

    Down button push and release the down button to scroll downward through the submenus. When the appropriate conditions exist, the evic displays the following messages: • turn signal on (with a continuous warning chime after 1 mile (1.6 km) of distance travelled) • left front turn signal lamp out (wit...

  • Page 253

    • remote start aborted — fuel low • remote start aborted — system fault • key in ignition • low tire • low tire pressure display for premium tpm system • service tpm system engine oil change indicator system — if equipped oil change required your vehicle is equipped with an engine oil change indicat...

  • Page 254

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Evic functions • compass/temperature/audio • average fuel economy • distance to empty (dte) • units in • elapsed time • tire pressure monitor (tp...

  • Page 255

    Prompted in the evic display to reset). When the fuel economy is reset, the display will read “reset” or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel reading before the reset. Distance to empty (dte) shows the estimated...

  • Page 256

    Upon reset, all digits will change to zeros, and time will start incrementing again if the ignition switch is in run or start. Display units of measure in to make your selection, push and release the right arrow button until “us” or “metric” appears. Personal settings (customer-programmable features...

  • Page 257

    And hold the right arrow button when in this display until “on” or “off” appears to make your selection. Auto unlock on exit when on is selected, all the vehicle’s doors will unlock when the driver’s door is opened, if the vehicle is stopped (manual transmission) or the vehicle is stopped and the tr...

  • Page 258

    Headlamp off delay when this feature is selected the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. Push and hold the right button when in this display until 0, 30, 60, or 90 appears to make your selection. Headlamps with wipers (available w...

  • Page 259

    Right arrow button when in this display until “off,” “30 sec,” “60 sec,” or “90 sec.” appears to make your selection. Hill start assist (hsa) — if equipped when “on”is selected, the hsa system is active. Refer to “electronic brake control system” in “starting and operating” for system function and o...

  • Page 260

    Manual compass calibration if the compass appears erratic and the “cal” indicator does not appear in the evic display, you must put the compass into the calibration mode manually as follows: 1. Start the engine. Leave the shift lever in park in order to enter the evic programming menus. 2. Push and ...

  • Page 261

    1. Turn the ignition switch on. 2. Push and hold the compass button for approxi- mately two seconds. 3. Push and release the down button until “compass variance” message and the last variance zone number displays in the evic. 4. Push and release the right button until the proper variance zone is sel...

  • Page 262

    Uconnect 230 – am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/...

  • Page 263

    Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations witho...

  • Page 264

    Clock setting procedure 1. Push and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, push the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minu...

  • Page 265

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 266

    Program type 16-digit character display classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc progra...

  • Page 267

    If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset station. Setup button pushing the setup button allows you to select between the following items: note: turn the tune/scroll control knob to scroll thr...

  • Page 268

    Note: • the available selections for each of the above entries varies depending upon the disc. • these selections can only be made while playing a dvd. • power — allows you to turn the power on and off (if equipped). • lock — locks out rear remote controls (if equipped). • ch1/ch2 — allows the user ...

  • Page 269

    The tune/scroll control knob to scroll up and down to select the number and then push to select. Subtitle language — if equipped selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc). You can select a language not listed by scr...

  • Page 270

    Note: the user will have to set these defaults before loading a disc. If changes are made to these settings after a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings. Am and fm buttons push the buttons to select ...

  • Page 271

    Disc button pushing the disc button will allow you to switch from am/fm modes to disc modes. Operation instructions — disc mode for cd and mp3/wma audio play, dvd – video the radio dvd player and many dvd discs are coded by geographic region. These region codes must match for the disc to play. If th...

  • Page 272

    Caution! This cd player will accept 4–3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. Eject button — ejecting compact disc(s) push the eject button and the pushbutton with the corresponding number (1-6) where the cd was loaded and the disc will unload an...

  • Page 273

    Rw/ff (cd mode) push and hold ff (fast forward) and the cd player will begin to fast forward until ff is released, or rw or another cd button is pushed. The rw (rewind) button works in a similar manner. Am or fm button (cd mode) switches the radio into the am or fm radio mode. Notes on playing mp3/w...

  • Page 274

    Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal cd audio tracks and computer files (including mp3/ wma files). Discs created with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs. The use of multisession...

  • Page 275

    Wma specification sampling fre- quency (khz) bit rate (kbps) wma 44.1 and 48 48, 64, 96, 128, 160, 192 vbr id3 tag information for artist, song title, and album title are supported for id3 version 1 tags. Id3 version 2 is not supported by the radios. Playlist files are not supported. Mp3 pro files a...

  • Page 276

    Folder by pushing the tune/scroll control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds. Info button — disc mode for mp3/wma play pushing the info button r...

  • Page 277

    Scan button (auxiliary mode) no function. Eject button (auxiliary mode) no function. Time button (auxiliary mode) push the time button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Rw/ff (auxiliary mode) no function. Set button (auxili...

  • Page 278

    Intended for home and other limited viewing uses only, unless otherwise authorized by macrovision. Reverse engineering or disassembly is prohibited. Dts “dts and “dts 2.0” are trademarks of digital theater systems, inc. Uconnect (satellite radio) — if equipped satellite radio uses direct satellite-t...

  • Page 279

    To access the esn/sid, refer to the following steps: esn/sid access with the ignition switch in the on/run or acc posi- tion and the radio on, push the setup button and scroll using the tune/scroll control knob until sirius id is selected. Push the tune/scroll control knob and the sirius id number w...

  • Page 280

    Operating instructions — uconnect (satellite) mode note: the ignition switch must be in the on/run or acc position to operate the radio. Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to see...

  • Page 281

    Music type button pushing this button once will turn on the music type mode for five seconds. Pushing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Toggle the music type button again to select the music type. By...

  • Page 282

    You may add a second channel to each pushbutton by repeating the above procedure with this exception: push the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2. This allows a total of 12 satellite channels to be stored into pushbutton memory. The...

  • Page 283

    Uconnect 130 operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electroni...

  • Page 284

    Another selection. Holding either button will bypass stations without stopping, until you release it. Time button push the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Push and hold the time button until the hours blink. 2. Adjust the hours by turning ...

  • Page 285

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 286

    Display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pushing the pushbutton twice. Every time a preset button is used, a corresponding ...

  • Page 287

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 288

    Seek button push the right seek button for the next selection on the cd. Push the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pushing and holding the seek but...

  • Page 289

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 290

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 291

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 292

    Uconnect 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off...

  • Page 293

    Another selection. Holding either button will bypass stations without stopping, until you release it. Voice command system (radio) — if equipped refer to “voice command” in “understanding the fea- tures of your vehicle”. Voice command button uconnect phone — if equipped push this button to operate t...

  • Page 294

    3. After adjusting the hours, push the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Push the tune/scroll con- trol knob to save time change. 5. To exit, push any button/knob or wait fiv...

  • Page 295

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 296

    Program type 16-digit character display classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc progra...

  • Page 297

    If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset station. Setup button pushing the setup button allows you to select between the following items: • set clock — pushing the select button will allow yo...

  • Page 298

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory (12 am and 12 fm stations). Disc/aux button pushing the disc/aux button will allow you to switch from am/fm modes to disc/au...

  • Page 299

    Caution! • this cd player will accept 4–3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • the uconnect 130 is a single cd player. Do not attempt to insert a second cd ...

  • Page 300

    Rw/ff push and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pushed. The rw (reverse) button works in a similar manner. Am/fm button push the button to select either am or fm mode. Set/rnd button (random play button) push this ...

  • Page 301

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 302

    Use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rates. Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56...

  • Page 303

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button — cd mode for mp3 play pushing the list button will bring up a list of all folders on the dis...

  • Page 304

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Time button (auxiliary mode) push this button to change the display to time of d...

  • Page 305

    1. The electronic serial number/sirius identification number (esn/sid). 2. Your vehicle identification number. To access the esn/sid, refer to the following steps: esn/sid access with the ignition switch in the on/run or acc posi- tion and the radio on, push the setup button and scroll using the tun...

  • Page 306

    • driving under wide bridges or along tall buildings can cause intermittent reception. • placing objects over or too close to the antenna can cause signal blockage. Operating instructions — uconnect (satellite) mode note: the ignition switch must be in the on/run or acc position to operate the radio...

  • Page 307

    Tune control (rotary) turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the channel. Music type button pushing this button once will turn on the music type mode for five seconds. Pushing the music type button or turning the tune/scroll control knob within...

  • Page 308

    You may add a second channel to each pushbutton by repeating the above procedure with this exception: push the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2. This allows a total of 12 satellite channels to be stored into pushbutton memory. The...

  • Page 309

    Connecting the ipod or external usb device use the connection cable to connect an ipod or external usb device to the vehicle’s usb/aux connector port which is located in the center console or glove compart- ment. Once the audio device is connected and synchronized to the vehicle’s ipod/usb/mp3 contr...

  • Page 310

    • the audio device can be controlled using the radio buttons to play, browse, and list the ipod contents. • the audio device battery charges when plugged into the usb/aux connector (if supported by the specific audio device). Controlling the ipod or external usb device using radio buttons to enter t...

  • Page 311

    • a single push backward rw or forward ff >> will jump backward or forward respectively, for five sec- onds. • use the seek and seek >> buttons to jump to the previous or next track. Pushing the seek >> button during play mode will jump to the next track in the list, or push the vr button and say ⬙ ...

  • Page 312

    List or browse mode during play mode, pushing any of the buttons described below, will bring up list mode. List mode enables scrolling through the list of menus and tracks on the audio device. Tune control knob: the tune control knob functions in a similar manner as the scroll wheel on the audio dev...

  • Page 313

    To exit list mode without selecting a track, push the same preset button again to go back to play mode . List button: the list button will display the top level menu of the ipod or external usb device. • turn the tune control knob to list the top-menu item to be selected and push the tune control kn...

  • Page 314

    Bluetooth streaming audio (btsa) music can be streamed from your cellular phone to the uconnect phone system. Refer to the uconnect radio supplement for further information on bluetooth connectivity. Controlling btsa using radio buttons to enter btsa mode, push either “aux” button on the radio or pu...

  • Page 315

    Browse browsing is not available on a bluetooth streaming audio (btsa) device. Only the current song that is playing will display info. Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches....

  • Page 316

    Pushing the center button will make the radio switch between the various modes available (am/fm/sat/ cd/hdd/aux etc.). The left-hand control is a rocker-type switch with a push-button in the center. The function of the left-hand control is different depending on which mode you are in. The following ...

  • Page 317

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 318

    Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and inner push knobs. Blower control rotate this control to regulate the...

  • Page 319

    Temperature control rotate this control to regulate the tem- perature of the air inside the passenger compartment. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures. Note: if your air conditionin...

  • Page 320

    • economy mode if economy mode is desired, push the a/c button to turn off the indicator light and the a/c compressor. Then, select panel, bi-level or floor mode and move the temperature control to the desired temperature. Mode control (air direction) rotate this control to choose from sev- eral pat...

  • Page 321

    • floor air is directed through the floor outlets with a small amount flowing through the defrost and side window demist outlets. • mix air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the winds...

  • Page 322

    Note: • continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • the use of the recirculation mode in cold or damp weather will cause windows to fog on the inside, because of moisture buildup inside the vehi...

  • Page 323

    Automatic operation operation of the system is quite simple. 1. Turn the mode control knob (right knob) and the blower control knob (left knob) to auto. Note: the auto position performs best for front seat occupants only. 2. Dial in the temperature you would like the system to maintain by ro- tating...

  • Page 324

    Insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduce airflow to the condenser, reducing air conditioning performance. Blower control for full automatic operation or for automatic blower operation, turn the blower knob ...

  • Page 325

    4 understanding your instrument panel 323.

  • Page 326

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center ...

  • Page 327

    • defrost air is directed through the windshield and side window demist outlets. Use this mode with maxi- mum blower and temperature settings for best wind- shield and side window defrosting. • air conditioner control push this button to turn on the air conditioning during manual operation only. Whe...

  • Page 328

    • extended use of recirculation may cause the windows to fog. If the interior of the windows begins to fog, push the recirculation button to return to outside air. Some temp/humidity conditions will cause captured interior air to condense on windows and hamper visibility. For this reason, the system...

  • Page 329

    Standard ms.90032 and 50% water is recommended. Refer to “maintenance procedures” in “maintaining your vehicle” for proper coolant selection. Winter operation use of the air recirculation mode during winter months is not recommended because it may cause window fogging. Vacation storage anytime you s...

  • Page 330

    Side window demisters a side window demister outlet is located at each end of the instrument panel. These non-adjustable outlets direct air toward the side windows when the system is in the floor, mix, or defrost mode. The air is directed at the area of the windows through which you view the outside...

  • Page 331

    Control setting suggestions for various weather conditions 4 understanding your instrument panel 329.

  • Page 333: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .335 ▫ manual transmission — if equipped . . . . . . .335 ▫ automatic transmission — if equipped . . . . .336 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .336 ▫ extreme cold weather (below –22°f or −...

  • Page 334

    䡵 autostick . . . . . . . . . . . . . . . . . . . . . . . . . .355 ▫ autostick (six-speed automatic transmission) . . . . . . . . . . . . . . . . . . . . . . . .355 ▫ autostick (cvt) — if equipped . . . . . . . . . . .357 䡵 four-wheel drive operation — if equipped . . . . . . . . . . . . . . . . . ....

  • Page 335

    ▫ electronic roll mitigation (erm) . . . . . . . . . .386 ▫ hill descent control (hdc) — if equipped . . .387 䡵 tire safety information . . . . . . . . . . . . .388 ▫ tire markings . . . . . . . . . . . . . . . . . . . . . . . .388 ▫ tire identification number (tin). . . . . . . . . . .392 ▫ tire te...

  • Page 336

    䡵 fuel requirements . . . . . . . . . . . . . . . . . .424 ▫ 2.0l and 2.4l engine . . . . . . . . . . . . . . . . . . .424 ▫ reformulated gasoline . . . . . . . . . . . . . . . . .424 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . .425 ▫ e-85 usage in non-flex fuel vehicles . . . . . . .425 ▫...

  • Page 337

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • before exiting a vehicle, always shift the transmis- sion into park, apply the parking brake and remove the key fob from the ignition. When leaving the v...

  • Page 338

    Automatic transmission — if equipped the shift lever must be in the park or neutral position before you can start the engine. Press the brake pedal before shifting to any driving gear. Note: you must press the brake pedal before shifting out of park. Tip start do not press the accelerator. Turn the ...

  • Page 339

    Warning! (continued) another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. Refer to “jump-starting” in “what to do in emer- gencies” for further information. Extreme cold weather (below –22°f or −30°c) to ensure reliable starting at these tempera...

  • Page 340

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 341

    Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in a gear higher than first gear. Caution! • launching in any gear except 1st gear will result in excess...

  • Page 342

    Never shift into reverse until the vehicle has come to a complete stop. Note: during cold weather, until the transmission lu- bricant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the transmis- sion. Recommended shift speeds to use your manual transmiss...

  • Page 343

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 344

    Note: you must press and hold the brake pedal while shifting out of park. Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You c...

  • Page 345

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. The key can only be re- moved from the ignition when the ignition is in the lock/o...

  • Page 346

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has only park, reverse, neutral, and drive shift positions. Manual shifts can be ma...

  • Page 347

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not in park. Check by trying to move the gear...

  • Page 348

    Warning! (continued) warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the ignition key in or near the vehicle (or in a location accessible to children). A child could operate power windows, other controls, or move the vehicle. Caution! • before moving the gear ...

  • Page 349

    Neutral (n) use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift the transmission into park if you must leave the vehicle. Warning! Do not coast in neutral and never turn off the ignition...

  • Page 350

    Control (refer to “autostick (six-speed automatic trans- mission)” in this section for further information) to select a lower gear. Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat buildup. If the transmission te...

  • Page 351

    In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following steps: 1. Stop the vehicle. 2. Shift the transmission into park. 3. Turn the ignition switch to the off position. 4. Wait approximately 10 seconds. 5. Restart the engine. 6. Shi...

  • Page 352

    Torque converter clutch a feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati- cally at calibrated speeds. This may result in a slightly different feeling or response during normal operation i...

  • Page 353

    The transmission shift lever has park, reverse, neu- tral, and drive shift positions. Some models include a low position (the low position manually downshifts the transmission to a lower available ratio based on vehicle speed); in others, manual shifts are made using the autostick shift control (ref...

  • Page 354

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not in park. Check by trying to move the gear...

  • Page 355

    Warning! (continued) warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the ignition key in or near the vehicle (or in a location accessible to children). A child could operate power windows, other controls, or move the vehicle. Caution! • before moving the gear ...

  • Page 356

    Neutral (n) use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift the transmission into park if you must leave the vehicle. Warning! Do not coast in neutral and never turn off the ignition...

  • Page 357

    Further information) to select a lower gear ratio. Under these conditions, using a lower gear ratio will improve performance and extend transmission life by reducing excessive shifting and heat buildup. During sustained high speed driving or trailer towing up long grades on hot days, the auto- matic...

  • Page 358

    Operation when the shift lever is in the drive position, the transmission will operate automatically, shifting between the six available gears. To engage autostick, simply tap the shift lever to the right or left (+/-) while in the drive position. Tapping (-) to enter autostick mode will down- shift...

  • Page 359

    • the system may revert to automatic shift mode if a fault or overheat condition is detected. To disengage autostick mode, hold the shift lever to the right (+) until “d” is once again displayed in the instru- ment cluster. You can shift in or out of the autostick mode at any time without taking you...

  • Page 360

    In autostick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result. It will remain in the selected gear until another upshift or downshift is chosen, except as described below: • the transmission will ...

  • Page 361

    Four-wheel drive operation — if equipped this feature provides full time, on-demand, four–wheel drive (4wd). Where one or more wheels have wheel spin or if addi- tional traction is needed in sand, deep snow, or loose traction surfaces, activate the “4wd lock” switch by pulling up once and releasing....

  • Page 362

    An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfacto- rily in off-road cond...

  • Page 363

    When to use low (l off-road) with the 4wd lock lever engaged — if equipped when driving off-road, shift into low (l off-road [if equipped] ) and activate the 4wd lock. This will provide additional traction and activates the numerous off-road features to improve handling and control on slippery or di...

  • Page 364

    Will allow the tires to get a fresh ⬙ bite ⬙ and help maintain your momentum. Caution! On icy or slippery roads, do not downshift at high engine rpm’s or vehicle speeds because engine brak- ing may cause skidding and loss of control. Mud deep mud creates a great deal of suction around the tires and ...

  • Page 365

    Hard surfaces. Be sure you have a way to reinflate the tires prior to reducing the pressure. Caution! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abr...

  • Page 366

    The front end begins to bounce, ease off the throttle slightly to bring all four tires back on the ground. As you approach the crest of the hill, ease off the throttle and slowly proceed over the top. If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maint...

  • Page 367

    Driving across an incline if at all possible avoid driving across an incline. If it is necessary, know your vehicle’s abilities. Driving across an incline places more weight on the down-hill wheels, which increases the possibilities of a down-hill slide or rollover. Make sure the surface has good tr...

  • Page 368

    Be attempted when necessary in a safe responsible man- ner. You should only drive through areas which are designated and approved. You should tread lightly and avoid damage to the environment. You should know your vehicles abilities and be able to recover it if some- thing goes wrong. You should nev...

  • Page 369

    Soft bottoms, the vehicle will sink in, effectively increas- ing the water level on the vehicle. Be sure to consider this when determining the depth and the ability to safely cross. Crossing puddles, pools, flooded areas or other standing water puddles, pools, flooded or other standing water areas n...

  • Page 370

    • check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and sus- pension. Retighten them, if required, and torque to the values specified in the service manual. • check for accumulations of plants or brush. These things could be a fire hazard. They mig...

  • Page 371

    The electric steering system experiences a fault that prevents it from providing assist, you will still have the ability to steer the vehicle manually. Alternate electric power steering efforts can be selected through the uconnect system. Refer to ”customer pro- grammable features” within “uconnect ...

  • Page 372

    Apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an autho- rized dealer. Caution! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the new vehicle ...

  • Page 373

    When the parking brake is applied with the ignition switch in the on position, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is de...

  • Page 374

    Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be...

  • Page 375

    Brake system your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. How- ever, the effort required to brake the vehicle will be much gr...

  • Page 376

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system (ebc). This system includes elec- tronic brake force distribution (ebd), anti-lock brake system (abs), brake assist system (bas), hill start assist (hsa), traction control system (tcs), electron...

  • Page 377

    Braking conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking. The abs performs a self-check cycle to ensure that the abs is working properly each time the vehicle is started and driven. During this self-check you may hear a slight clicking sound as we...

  • Page 378

    Warning! (continued) • the abs cannot prevent the natural laws of phys- ics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent collisions, including th...

  • Page 379

    Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 380

    Does not apply the throttle before this time expires, the system will release brake pressure and the vehicle will roll down the hill as normal. The following conditions must be met in order for hsa to activate: • the feature must be enabled. • the vehicle must be stopped. • park brake must be off. •...

  • Page 381

    Towing with hsa hsa will also provide assistance to mitigate roll back while towing a trailer. Warning! • if you use a trailer brake controller with your trailer, the trailer brakes may be activated and deactivated with the brake switch. If so, there may not be enough brake pressure to hold both the...

  • Page 382

    For vehicles not equipped with the evic, perform the following steps: 1. Center the steering wheel (front wheels pointing straight forward). 2. Shift the transmission into park. 3. Apply the parking brake. 4. Start the engine. 5. Rotate the steering wheel slightly more than one-half turn to the left...

  • Page 383

    To the wheel that is not spinning. Bld may remain enabled even if tcs and esc are in a reduced mode. Electronic stability control (esc) this system enhances directional control and stability of the vehicle under various driving conditions. Esc cor- rects for over-steering or under-steering of the ve...

  • Page 384

    Warning! (continued) manner, which could jeopardize the user’s safety or the safety of others • vehicle modifications, or failure to properly main- tain your vehicle, may change the handling charac- teristics of your vehicle, and may negatively affect the performance of the esc system. Changes to th...

  • Page 385

    Indicator light ⬙ will be illuminated. All other stability features of esc function normally. This mode is intended to be used if the vehicle is in deep snow, sand or gravel conditions and more wheel spin than esc would nor- mally allow is required to gain traction. To turn esc on again, momentarily...

  • Page 386

    Light ⬙ will illuminate and the “esc off” message will appear in the odometer. Push and release the trip odom- eter button located on the instrument cluster to clear this message. In this mode, esc and tcs, except for the “limited slip” feature described in the tcs section, are turned off until the ...

  • Page 387

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is cycled to the on/ run position. It should go out with the engine running. If the “esc activation/malfunction indi...

  • Page 388

    When esc becomes inactive following the maneuver that caused the esc activation. The “esc off indicator light” indicates the electronic stability control (esc) is partially off or full off. Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver...

  • Page 389

    Hill descent control (hdc) — if equipped this system maintains vehicle speed while descending hills during off-road driving situations. Hdc will auto- matically apply the brakes to control downhill speed to between 4 mph (7 km/h) and 6 mph (9 km/h) depending on terrain. The system is activated by pl...

  • Page 390

    Hdc is only intended for low speed off-road driving. At vehicle speeds above 31 mph (50 km/h) hdc will no longer function. If the “hdc indicator light” begins to flash this indicates that the brakes are getting too hot and the vehicle should be stopped to allow the brakes to cool. Warning! Hdc is on...

  • Page 391

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 392

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ ....Blank.... ⴖ = passenger car tire based on european design standards, or lt = light truck tire based...

  • Page 393

    Example: r = construction code – ⬙ r ⬙ means radial construction, or – ⬙ d ⬙ means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating t...

  • Page 394

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 395

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 396

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 397

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 5 starting and ...

  • Page 398

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 399

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in the “starting and operating” sec- tion of this manual. To determin...

  • Page 400

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 401

    5 starting and operating 399.

  • Page 402

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 403

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 404

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 405

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits ...

  • Page 406

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 407

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 408

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Run flat tires — if equipped run flat tires a...

  • Page 409

    Equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spa...

  • Page 410

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 411

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 412

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (1.6 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information....

  • Page 413

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance w...

  • Page 414

    Warning! (continued) braking of your vehicle. This can cause unpredict- able handling and stress to steering and suspen- sion components. You could lose control and have a collision resulting in serious injury or death. Use only the tire and wheel sizes with load ratings approved for your vehicle. •...

  • Page 415

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation a...

  • Page 416

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (7.0 kpa) for every 12°f (6.5°c). This means that when the ...

  • Page 417

    Note: when filling warm tires, the tire pressure may need to be increased up to an additional 4 psi (30 kpa) above the recommended cold placard pressure in order to turn the tire pressure monitoring telltale light off. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) in ...

  • Page 418

    Caution! (continued) • using aftermarket tire sealants may cause the tire pressure monitoring system (tpms) sensor to be- come inoperable. After using an aftermarket tire sealant it is recommended that you take your vehicle to an authorized dealership to have your sensor function checked. • after in...

  • Page 419

    Base system this is the tpms warning indicator located in the instrument cluster. The tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure lev- els. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver m...

  • Page 420

    Check tpms warnings the tire pressure monitoring telltale light will flash on and off for 75 seconds and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The ti...

  • Page 421

    4. For each subsequent ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare tire, the tp...

  • Page 422

    • various tire pressure monitoring system messages, which display in the electronic vehicle information center (evic) • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster and a...

  • Page 423

    The graphic display of the pressure value(s) will stop flashing, and the tire pressure monitoring light will extinguish once the updated tire pressure(s) have been received. Note: when filling warm tires, the tire pressure may need to be increased up to an additional 4 psi (30 kpa) above the recomme...

  • Page 424

    Text message will not be present, and a pressure value will be displayed instead of dashes. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing some form...

  • Page 425

    3. However, after driving the vehicle for up to 20 min- utes above 15 mph (24 km/h), the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system” mes- sage for a minimum of five seconds and then d...

  • Page 426

    Fuel requirements 2.0l and 2.4l engine these engines are designed to meet all emissions regulations and provide opti- mum fuel economy and performance when using high quality unleaded “regu- lar” gasoline having a posted octane num- ber of 87 as specified by the (r+m)/2 method. The use of higher oct...

  • Page 427

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Caution! Do not use gasoline containing methanol or gaso- line containing more than 15% ethanol (e-15). Use of these blends may result in starting and drivability problems, damage critical fuel s...

  • Page 428

    Mmt in gasoline methylcyclopentadienyl manganese tricarbonyl (mmt) is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended wi...

  • Page 429

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine per- formance and damage the emissions control sys- tem. • an out-of-tune engine or certain fuel or ignitio...

  • Page 430

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 431

    After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. Caution! • damage to the fuel system or emission control system could result from using an improper fuel tank filler c...

  • Page 432

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gaso...

  • Page 433

    Vehicle loading as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or b-pillar. Vehicle certification label your vehicle has a vehicle certification label attached to the driver’s door b-pillar. The la...

  • Page 434

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 435

    Caution! Do not load your vehicle any heavier than the gvwr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in this section you will find safety ti...

  • Page 436

    The recommended way to measure gtw is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Gross a...

  • Page 437

    Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-carryi...

  • Page 438

    Warning! (continued) • weight distributing systems may not be compat- ible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable rec- reational vehicle dealer for additional information. Trailer hitch classification the following chart provides the industry stand...

  • Page 439

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.0l auto/man 22 sq ft (2.04 sq m) 1,000 lbs (450 ...

  • Page 440

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further information. Trailer and ton...

  • Page 441

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the maximum combine...

  • Page 442

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 443

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized. Towing requirements — tires • do not attempt to tow a trailer while ...

  • Page 444

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • an electronically actuated trailer brake controller is required when towing a trailer w...

  • Page 445

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing requirements — trailer lights an...

  • Page 446

    Four-pin connector 1 — female pins 2 — male pin 3 — ground 4 — park 5 — left stop/turn 6 — right stop/turn seven-pin connector 1 — battery 2 — backup lamps 3 — right stop/turn 4 — electric brakes 5 — ground 6 — left stop/turn 7 — running lamps 444 starting and operating.

  • Page 447

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Manual transmission — if equipped if using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippag...

  • Page 448

    Autostick — if equipped when using the autostick shift control, select the highest gear that allows for adequate performance and avoids frequent downshifts. For example, choose ⬙ 4 ⬙ if the desired speed can be maintained. Choose ⬙ 3 ⬙ or ⬙ 2 ⬙ if needed to maintain the desired speed. To prevent exc...

  • Page 449

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neu- tral • key in acc position not allowed dolly tow front fwd models only fwd models only rear n...

  • Page 450

    Note: • when recreationally towing your vehicle, always fol- low applicable state and provincial laws. Contact state and provincial highway safety offices for additional details. • vehicles equipped with manual transmissions may be recreationally towed (flat towed) at any legal highway speed, for an...

  • Page 451: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .451 䡵 if your engine overheats . . . . . . . . . . . .451 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .452 ▫ torque specifications . . . . . . . . . . . . . . . . . .452 䡵 jacking a...

  • Page 452

    䡵 freeing a stuck vehicle . . . . . . . . . . . . .479 䡵 shift lever override . . . . . . . . . . . . . . . .481 䡵 towing a disabled vehicle . . . . . . . . . . .482 ▫ with ignition key . . . . . . . . . . . . . . . . . . . . .484 450 what to do in emergencies.

  • Page 453

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel, below the radio. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the ...

  • Page 454

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 455

    **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tig...

  • Page 456

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to...

  • Page 457

    Jack location the jack and jack-handle are stowed under the load floor in the cargo area. Spare tire stowage the compact spare tire is stowed under the rear load floor in the cargo area. Spare tire removal lift up the load floor cover and remove the hold down. Preparations for jacking 1. Park the ve...

  • Page 458

    2. Turn on the hazard warning flasher. 3. Set the parking brake. 4. Place the shift lever in park (automatic transmission) or reverse (manual transmission). 5. Turn off the ignition. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For ex- ample, if changing...

  • Page 459

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 460

    2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. Note: there are front and rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts on one of the flanges in the sill flange ass...

  • Page 461

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. Jacking locations front jacking location 6 what to do in emergencies 459.

  • Page 462

    Do not raise the vehicle until you are sure the jack is securely engaged. 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 463

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. Caution! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damag...

  • Page 464

    Warning! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. Note: the wheel cover is held on the wheel by the wheel nuts. When reinstalling the original wheel, prop- erly align the wheel cover to the valve stem, place the wheel cover onto the ...

  • Page 465

    Warning! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immedi- ately. 10. Check the spare tire pressure as soon as possible. Correct the tire pressure as required. Road tire installation vehicles ...

  • Page 466

    3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in se...

  • Page 467

    3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Refer to “torque specifications” in this sec- tion for correct lug nut torque. 5. After 25 miles (40 km) c...

  • Page 468

    Tire service kit components and operation using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black ai...

  • Page 469

    Using the deflation button push the deflation button (2) to reduce the air pressure in the tire if it becomes over-inflated. Tire service kit usage precautions • replace the tire service kit sealant bottle (1) and sealant hose (6) prior to the expiration date (printed at the lower right hand corner ...

  • Page 470

    From the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tire service kit. • you can use the tire service kit air pump to inflate...

  • Page 471

    Warning! (continued) • keep tire service kit away from open flames or heat source. • a loose tire service kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tire service kit in the place provided. Failure to follow these warn- ings can result ...

  • Page 472

    On the ground. This will provide the best positioning of the kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceeding. 3. Place the transmission in park (auto transmission) or in gear (man...

  • Page 473

    Note: sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 – 10 seconds through the sealant hose (6): 1. Push the power button (4) to turn off the tire service kit. Disconnect the sealant hose (6) from the valve stem. Make sure the valve stem is ...

  • Page 474

    If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tire becomes over-inflated, push the defla- tion button to reduce the tire pressure to the recom- mend...

  • Page 475

    Distribution of the tire service kit sealant within the tire. Do not exceed 55 mph (90 km/h). Warning! Tire service kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using tire service kit. Do not exceed 55 mph (90 km/h) until the tire is repaired or rep...

  • Page 476

    Note: if the tire becomes over-inflated, push the defla- tion button to reduce the tire pressure to the recom- mended inflation pressure before continuing. 2. Disconnect the tire service kit from the valve stem, reinstall the cap on the valve stem and unplug from 12 volt outlet. 3. Place the tire se...

  • Page 477

    The front of the housing. Push the bottle into the housing. An audible click will be heard indicating the bottle is locked into place. 6. Verify that the cap is installed on the fitting at the end of the sealant hose (6) and return the hose to its storage area (located on the bottom of the air pump)...

  • Page 478

    Preparations for jump-start the battery in your vehicle is located in the front of the engine compartment below the air intake duct. To access the battery remove the air intake duct by turning the two finger screws, located on the radiator support. Air intake finger screws positive battery post 476 ...

  • Page 479

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 480

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Note: remove air intake before proceeding with this jump-starting procedure. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to...

  • Page 481

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the dis- charged battery. 2. Disconnect the opposite end of the negative (-) jumper cable...

  • Page 482

    And reverse (with automatic transmission) or 2nd gear and reverse (with manual transmission), while gently pressing the accelerator. Use the least amount of accel- erator pedal pressure that will maintain the rocking motion, without spinning the wheels, or racing the engine. Caution! Racing the engi...

  • Page 483

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 484

    4. Turn the ignition switch to the acc or on/run position, but do not start the engine. 5. Press and maintain firm pressure on the brake pedal. 6. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever forward. 7. Move the shift lever to the neutral...

  • Page 485

    Towing condition wheels off the ground manual trans- mission 6-speed auto- matic (fwd only) 6-speed auto- matic 4wd cvt automatic transmission flat tow none • transmission in neutral • key in acc or on/run po- sition if transmission is operable: • transmission in neutral • 25 mph (40 km/h) max speed...

  • Page 486

    With ignition key automatic transmission • front wheel drive (fwd) vehicles can be towed with the front wheels elevated, or on a flatbed truck (all four wheels off the ground). • four-wheel drive (4wd) vehicles can be towed on a flatbed truck (all four wheels off the ground). If the transmission is ...

  • Page 487

    Manual transmission • front wheel drive (fwd) or four-wheel drive (4wd) vehicles can be flat towed (all four wheels on the ground) with the transmission in neutral. • fwd vehicles can be towed with the front wheels elevated. • fwd or 4wd vehicles can be towed on a flatbed truck (all wheels off the g...

  • Page 488

    Without the ignition key special care must be taken when the vehicle is towed with the ignition in the lock/off position. The only approved method of towing without the ignition key is with a flatbed truck. Proper towing equipment is neces- sary to prevent damage to the vehicle. 486 what to do in em...

  • Page 489: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.0l . . . . . . . . . .489 䡵 engine compartment — 2.4l . . . . . . . . . .490 䡵 onboard diagnostic system — obd ii . .491 ▫ loose fuel filler cap message . . . . . . . . . . . .491 䡵 emissions inspection and maintenance programs . . . . . . ....

  • Page 490

    ▫ automatic transmission (six-speed) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .516 ▫ automatic transmission (cvt) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .518 ▫ manual transmission — if equipped . . . . . . .520 ▫ rear drive assembly (rda) — awd/4wd...

  • Page 491

    Engine compartment — 2.0l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 7 maintaining your vehicle 48...

  • Page 492

    Engine compartment — 2.4l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 490 maintaining your vehicle.

  • Page 493

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 494

    Persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil light off. Emissions inspection and maintenance programs in some localities, ...

  • Page 495

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 496

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 497

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, or air conditi...

  • Page 498

    At the low end of the indicated range will result in the oil level at the full end of the indicator range. Caution! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Al...

  • Page 499

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american petroleum institute (api). The manufacturer only recommends api certified engine oils. This symbol certifies 0w-20, 5w- 20, 0w-30, 5w-30 and 10w-30 en- gine oils. Cau...

  • Page 500

    Synthetic engine oils you may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Synthetic engine oils which do not have both the engine oil certification mark and the correct sae...

  • Page 501

    Engine air cleaner filter refer to the “maintenance schedule” in the “mainte- nance schedules” section for the proper maintenance intervals. Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air inductio...

  • Page 502

    Warning! (continued) splashes in eyes or on skin, flush the area imme- diately with large amounts of water. Refer to “jump-starting procedures” in “what to do in emergencies” for further information. • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a b...

  • Page 503

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 504

    Protection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment. Note: use only manufacturer approved a/c system pag compressor oil and refriger...

  • Page 505

    5. Remove the a/c air filter by pulling it straight out of the housing. 6. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. Caution! The a/c air filter is identified with an arrow...

  • Page 506

    Components to ensure proper function. When performing other underhood services, the hood latch, release mecha- nism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high qual...

  • Page 507

    In cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exer...

  • Page 508

    Warning! (continued) • a hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your ve- hicle in areas where your exhaust system can con- tact anything that can burn. ...

  • Page 509

    In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, including a tune-up to manufacturer’s specifica- tions, should be obtai...

  • Page 510

    Applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh engine coolant (anti- freeze). Check the front of the a/c condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from...

  • Page 511

    Caution! (continued) organic additive technology (oat) engine cool- ant is different and should not be mixed with hybrid organic additive technology (hoat) en- gine coolant (antifreeze) or any “globally compat- ible” coolant (antifreeze). If a non-oat engine coolant (antifreeze) is introduced into t...

  • Page 512

    That meets the requirements of fca material standard ms.90032. When adding engine coolant (antifreeze): • we recommend using mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) that meets the requirements of fca ma- terial standard ms.90032. • mix a minimum soluti...

  • Page 513

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign mat...

  • Page 514

    Coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling and warm to normal operating tempera- ture, the level of the engine coolant (antifreeze) in the bottle should be between the “add” and “full” lines shown on the ...

  • Page 515

    • if frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested for leaks. • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms.90032) and distilled water for proper corrosion protection of your engine w...

  • Page 516

    Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning light is on. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level u...

  • Page 517

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid ...

  • Page 518

    Caution! Use of improper brake fluids will affect overall clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of clutch function and the ability to shift the transmis- sion. Automatic transmission (six-speed) — if equipped selection of lubricant (six-speed...

  • Page 519

    Leaks. Avoid using transmission sealers as they may adversely affect seals. Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is prese...

  • Page 520

    Fluid becomes contaminated (with water, etc.), or if the transmission is disassembled for any reason. Automatic transmission (cvt) — if equipped selection of lubricant (cvt) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufac...

  • Page 521

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 522

    Manual transmission — if equipped lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check check the fluid level by removing the fill plug. The fluid level ...

  • Page 523

    Add fluid, if necessary, to maintain the proper level. Frequency of fluid change refer to the “maintenance schedule” for the proper maintenance intervals. Power transfer unit (ptu) — awd/4wd models only lubricant selection use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, ...

  • Page 524

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road...

  • Page 525

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 526

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar wheel cleaner. Note: if your vehicle is equipped with dark v...

  • Page 527

    • for tough stains, apply mopar total clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue...

  • Page 528

    Caution! Direct contact of air fresheners, insect repellents, suntan lotions, or hand sanitizers to the plastic, painted, or decorated surfaces of the interior may cause permanent damage. Wipe away immediately. Caution! Damage caused by these type of products may not be covered by your new vehicle l...

  • Page 529

    Equipped with radio antennas. Do not use scrapers or other sharp instrument that may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or cloth that you are using. Do not spray cleaner directly on the mirror. Instrument panel cover the instrument panel cover has a ...

  • Page 530

    2. Dry with a soft cloth. Seat belt maintenance do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use mopar total clean, a mild soap solution, or lukewarm water. Do not r...

  • Page 531

    Warning! (continued) • before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged. • if the replaced fuse blows again, contact an autho- rized dealer. • if a general protection fuse for safety systems (air bag system, braking system...

  • Page 532

    Cavity cartridge fuse mini-fuse description 1 20 amp blue – trailer tow – if equipped 2 – 15 amp lt blue awd/4wd control module – if equipped 3 – 10 amp red rear center brake light switch 4 – 10 amp red ignition switch/clock spring 5 – 15 amp lt blue battery feed for power tech 6 – 10 amp red power ...

  • Page 533

    Cavity cartridge fuse mini-fuse description 11 – 15 amp lt blue power outlet 12 – 20 amp yellow 115v ac inverter – if equipped 13 – 20 amp yellow cigar lighter 14 – 10 amp red instrument cluster 15 40 amp green – radiator fan 16 – 15 amp lt blue dome lamp/sunroof/rear wiper motor 17 – 10 amp red wir...

  • Page 534

    Cavity cartridge fuse mini-fuse description 23 – 15 amp lt blue auto shutdown relay 24 – 15 amp lt blue power sunroof – if equipped 25 – 10 amp red heated mirror – if equipped 26 – 15 amp lt blue auto shutdown relay 27 – 10 amp red airbag control module 28 – 10 amp red airbag control module/ occupan...

  • Page 535

    Cavity cartridge fuse mini-fuse description 33 – 10 amp red j1962 conn/powertrain con- trol module 34 30 amp pink – antilock brakevalve 35 40 amp green – antilock brake pump 36 30 amp pink – headlamp/washer control/ smart glass – if equipped 37 – 25 amp clear diesel heater and h2/mod power top cauti...

  • Page 536

    Vehicle storage if you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • disengage the mini-fuse in the power distribution center labeled iod (ignition off-draw). • or disconnect the negative cable from the battery. • anytime you store your ...

  • Page 537

    Exterior bulbs bulb number low beam/high beam headlamp h13 front park/turn signal/side marker lamp 3757ka front fog lamp psx24w center high mounted stop lamp (chmsl) led assembly (serviced at authorized dealer) rear tail/turn/stop lamp 3157 backup lamp w16w (921) license lamp w5w bulb replacement no...

  • Page 538

    3. Remove the green connector from the back of the bulb by pulling straight back. 4. Twist the bulb to the left. 5. Pull bulb outward from assembly. Note: these are halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which ...

  • Page 539

    License lamps 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate. 2. Rotate the socket 1/4 turn counterclockwise. 3. Pull the bulb from the socket. Center high-mounted stoplamp this light is an led assembly. See your authorized dealer for replac...

  • Page 540

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of fca material standard ms.90032. Engine oil we...

  • Page 541

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 542

    Chassis component fluid, lubricant, or genuine part automatic transmission (cvt) — if equipped use only mopar cvtf+4 continuously variable transmission fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Automatic transmission (six-speed...

  • Page 543

    Component fluid, lubricant, or genuine part power transfer unit (ptu) we recommend you use mopar gear & axle lubricant sae 80w-90 api gl 5. Brake master cylinder we recommend you use mopar dot 3, sae j1703 should be used. If dot 3, sae j1703 brake fluid is not available, then dot 4 is acceptable. Po...

  • Page 545: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . .544 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .547 8.

  • Page 546

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 547

    Note: under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 hours of engine run time, whichever comes first. The 350 hours of engine run or idle time is generally only a concern for fleet customers. Severe duty all models change engine oil at 4,00...

  • Page 548

    Required maintenance intervals . Refer to the maintenance schedules on the following page for the required maintenance intervals. At every oil change interval as indicated by oil change indicator system: • change oil and filter. • rotate the tires. Rotate at the first sign of irregu- lar wear, even ...

  • Page 549

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 550

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 551

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 552

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 553

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 555: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .555 ▫ prepare for the appointment. . . . . . . . . . . . .555 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .555 ▫ be reasonable with requests ....

  • Page 556

    䡵 publication order forms . . . . . . . . . . . .560 䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .561 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .561 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .561 ▫ temperature gr...

  • Page 557

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 558

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 559

    In mexico contact av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 puerto rico and u.S. Virgin islands customer service chrysler international services llc p.O. Box 191857 san juan 00919-1857 tel.: (787) 782-57...

  • Page 560

    Warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufacturer’s service contract, you will receive plan provisions and an owner identification card in the mail within three weeks of the vehicle delivery date. If you have any questions abo...

  • Page 561

    Warranty information see the warranty information booklet, located on the dvd, for the terms and provisions of fca us llc warranties applicable to this vehicle and market. Mopar parts mopar fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for...

  • Page 562

    Defect to the canadian government should contact trans- port canada, motor vehicle defect investigations and recalls at 1-800-333-0510 or go to http://www.Tc.Gc.Ca/ roadsafety/ publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. V...

  • Page 563

    Call toll free at: • 1-800-890-4038 (u.S.) • 1-800-387-1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 564

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 565: Index

    Index 10

  • Page 566

    Adding engine coolant (antifreeze) . . . . . . . . . . . .509 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .428 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .504 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .426 adjust down . . . . . . ....

  • Page 567

    Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . .537 disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .511 anti-lock brake system (abs) . . . . . . . . . . . . . . . .374 anti-lock warning light . . . . . . . . . . . . . . . . . . . .239 appearance care . . . . . ....

  • Page 568

    Bulbs, light . . . . . . . . . . . . . . . . . . . . . . . . . .101, 534 calibration, compass . . . . . . . . . . . . . . . . . . . . . .258 camera, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . .179 capacities, antifreeze (engine coolant) . . . . . . . . . .537 capacities, fluid . . . ...

  • Page 569

    Installing child restraints using the vehicle seat belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 lower anchors and tethers for children . . . . . . .82 older children and child restraints . . . . . . . . . .78 seating positions . . . . . . . . . . . . . . . . . . . . . ....

  • Page 570

    Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202 customer assistance . . . . . . . . . . . . . . . . . . . . . . .555 data recorder, event . . . . . . . . . . . . . . . . . . . . . . .74 dealer service. . . . . . . . . . . . . . . . . . . . . . . . . . . .494 defroster, rear w...

  • Page 571

    Emergency, in case of jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .454 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .475 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .482 emission control system maintenance . . . . . . . . . .492 engine....

  • Page 572

    Fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . . .537 fluid leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 fluid level checks automatic transaxle . . . . . . . . . . . . . . . . . . . . .519 automatic transmission . . . . . . . . . . . . . . . . . .517 cooling s...

  • Page 573

    Gauges fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . .344, 351 gear select lever override . . . . . . . . . . . . . . . . . .481 general information . . . . . . . . . . . . . . . . . . . . . . .143 glass cleaning...

  • Page 574

    Instrument cluster . . . . . . . . . . . . . . . . . .229, 230, 243 instrument panel and controls . . . . . . . . . . . . . . .217 instrument panel cover . . . . . . . . . . . . . . . . . . . . .527 instrument panel lens cleaning . . . . . . . . . . . . . . .527 integrated power module (fuses) . . ....

  • Page 575

    Brake warning . . . . . . . . . . . . . . . . . . . . . . . . .226 bulb replacement . . . . . . . . . . . . . . . . . . . . . . .535 cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 center mounted stop . . . . . . . . . . . . . . . . . . . .537 daytime running . . . . . . . . ....

  • Page 576

    Lug nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .452 lumbar support . . . . . . . . . . . . . . . . . . . . . . . . . .155 maintenance free battery. . . . . . . . . . . . . . . . . . . .499 maintenance procedures . . . . . . . . . . . . . . . . . . . .494 maintenance schedule . ...

  • Page 577

    Oil change indicator, reset . . . . . . . . . . . . . . . . . .251 oil, engine . . . . . . . . . . . . . . . . . . . . . . .495, 537, 538 capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .537 change interval . . . . . . . . . . . . . . . . . . . . . . . .496 checking . . . . . . . . ...

  • Page 578

    Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191 transfer unit . . . . . . . . . . . . . . . . . . . . . . . . . .521 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 power seats down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151 forward ...

  • Page 579

    Remote control door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 security alarm . . . . . . . . . . . . . . . . . . . . . . . . . .18 remote keyless entry (sedan) . . . . . . . . . . . . . . . . .20 remote starting system. . . . . . . . . . . . . . . . . . . . . .26 replacement bu...

  • Page 580

    Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41, 99 adjustable shoulder belt . . . . . . . . . . . . . . . . . . .48 adjustable upper shoulder anchorage . . . . . . . . .48 child restraint . . . . . . . . . . . . . . . . . . . . . . . . . .75 extender . . . . . . . . . . . . ....

  • Page 581

    Spare tire . . . . . . . . . . . . . . . . . . . . .406, 407, 408, 455 spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .538 speed control accel/decel . . . . . . . . . . . . . . . . . . . . . . . . . . .178 cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177 r...

  • Page 582

    Air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . .400 chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .412 changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .454 compact spare . . . . . . . . . . . . . . . . . . . . . . . . .407 general information ....

  • Page 583

    Minimum requirements . . . . . . . . . . . . . . . . . .439 tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .445 trailer and tongue weight . . . . . . . . . . . . . . . .438 wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .443 trailer towing guide. . . . . . ....

  • Page 584

    Understanding your instrument panel. . . . . . . . . . .217 uniform tire quality grades . . . . . . . . . . . . . . . . .561 universal consumer interface (uci) connector . . . .306 universal transmitter . . . . . . . . . . . . . . . . . . . . . .181 unleaded gasoline . . . . . . . . . . . . . . . . ...

  • Page 585

    Windshield defroster . . . . . . . . . . . . .99, 319, 324, 325 windshield washers . . . . . . . . . . . . . . . . . . . .170, 172 windshield wiper blades . . . . . . . . . . . . . . . . . . . .504 windshield wipers . . . . . . . . . . . . . . . . . . . . . . . .170 wiper blade replacement . . . . ....

  • Page 586

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 587

    First edition printed in u.S.A. Stick with the specialists ® 16mk74-126-aa ©2015 fca us llc. All rights reserved. Jeep is a registered trademark of fca us llc..