1. DL manuals
  2. Jeep
  3. Automobile
  4. 2016 Patriot
  5. Owner's Manual

Jeep 2016 Patriot Owner's Manual

Other manuals for 2016 Patriot: User Manual, Owner's Manual

Summary of 2016 Patriot

  • Page 1

    Patriot o w n e r ’ s m a n u a l 2 0 1 6.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new fca us llc vehicle. Be assured that it represents precision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engine...

  • Page 7

    Control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the unive...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision, bodily injury and/or death. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 sentry k...

  • Page 12

    ▫ to lock the doors and liftgate . . . . . . . . . . . .22 ▫ sound horn with remote key lock . . . . . . . . .22 ▫ flash lights with remote key lock/unlock . . .23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . .24 ▫ programming additional transmitters. . . . . . . .25 ▫ transmitter batte...

  • Page 13

    䡵 liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 䡵 occupant restraint systems . . . . . . . . . .41 ▫ important safety precautions . . . . . . . . . . . . . .41 ▫ seat belt systems . . . . . . . . . . . . . . . . . . . . . .42 ▫ supplemental restraint system (srs) . . . . . . . ....

  • Page 14

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 15

    Note: if you try to remove the key before you place the shift lever in park, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in park, rotate the key clockwise slightly, and then remove the key as described above. If a malfunction occurs...

  • Page 16

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking...

  • Page 17

    Sentry key the sentry key immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded elec...

  • Page 18

    Caution! The sentry key immobilizer system is not compat- ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics. ...

  • Page 19

    Customer key programming if you have two valid sentry keys, you can program new sentry keys to the system by performing the following procedure: 1. Cut the additional sentry key transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition ...

  • Page 20

    Note: if a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of s...

  • Page 21

    To arm the system 1. Remove the key from the ignition switch and get out of the vehicle. 2. Lock the door using either the power door lock switch or the remote keyless entry (rke) transmitter and close all doors. 3. The vehicle security light in the instrument cluster will flash rapidly for approxim...

  • Page 22

    Once the vehicle security alarm is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, push the unlock button on the rke transmitter to disarm the vehicle security alarm. Vehicle security alarm manual override the vehicle security alarm will not arm...

  • Page 23

    To unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn o...

  • Page 24

    Note: pushing the lock button on the rke transmitter while you are inside the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Push the unlock button to deactivate the vehicle security alarm. Illuminated approac...

  • Page 25

    • for vehicles not equipped with the evic, perform the following steps: 1. Push the lock button on a programmed rke transmitter for at least 4 seconds, but no longer than 10 seconds. Then, push the panic button while still holding the lock button. 2. Release both buttons at the same time. 3. Test th...

  • Page 26

    • for vehicles not equipped with the evic, perform the following steps: 1. Push and hold the unlock button on a pro- grammed rke transmitter for at least 4 seconds but no longer than 10 seconds. Then, push and hold the lock button while still holding the unlock button. 2. Release both buttons at the...

  • Page 27

    Note: when you turn off the panic alarm by pushing the panic button a second time, you may have to move closer to the vehicle due to the radio frequency noises of the system. Programming additional transmitters refer to “sentry key” in “things to know before start- ing” for further information. If y...

  • Page 28

    3. To reassemble the rke transmitter case, snap the two halves together. Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: thi...

  • Page 29

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • hazard switch off • brake switch inactive (brake pedal not pushed) • ignition key removed from ignition switch • battery at an acceptable char...

  • Page 30

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 31

    • if your power door locks were unlocked, remote start will automatically lock the doors. • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch must be cycled to the on/run position before you can repeat the start sequence for...

  • Page 32

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada licence-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 33

    Warning! • for personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. (continued) warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in ...

  • Page 34

    Power door locks a power door lock switch is located on the driver’s and front passenger’s door panel. Push this switch to lock or unlock the doors and liftgate. Note: to prevent from locking the key in the vehicle, the power door lock switch will not operate when the key is in the ignition and eith...

  • Page 35

    Auto lock doors — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). Auto lock doors programming the automatic door locks feature can be enabled or disabled as follows: • for veh...

  • Page 36

    Automatic unlock doors on exit the doors will unlock automatically if: • the automatic unlock doors on exit feature is en- abled. • the transmission was in gear, and the vehicle speed returned to 0 mph (0 km/h). • the transmission is in neutral or park. • the driver’s door is opened. • the doors wer...

  • Page 37

    Note: • if you do not hear the chime, it means that the system did not enter the programming mode and you will need to repeat the procedure. • use the automatic unlock doors on exit feature in accordance with local laws. Child-protection door lock system — rear doors to provide a safer environment f...

  • Page 38

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: for emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window, and open the do...

  • Page 39

    Power windows — if equipped power window switches the window controls on the driver’s door trim panel control all the door windows. There are single window controls on each passenger door trim panel, which oper- ate the passenger door windows. The window controls will operate when the ignition switc...

  • Page 40

    Auto-down the driver’s door window switch has an auto-down feature. Push the window switch past the first detent, release, and the window will go down automatically. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Power window switch lo...

  • Page 41

    Window lockout switch the window lockout switch on the driver’s door allows you to disable the window controls on the rear passenger doors. To disable the window controls on the rear pas- senger doors, push the window lockout switch. To enable the rear window controls, push the window lockout switch...

  • Page 42

    Note: although the liftgate has no inside release mechanism, the liftgate trim panel includes an opening with a snap-in cap that provides access to release the latch in the event of an electrical system malfunction. Warning! • driving with the liftgate open can allow poisonous exhaust gases into you...

  • Page 43

    Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: • seat belt systems • supplemental restraint systems (srs) air bags • supplemental active head restraints • child restraints important safety precautions please pay close attention to the...

  • Page 44

    5. You should read the instructions provided with your child restraint to make sure that you are using it properly. 6. All occupants should always wear their lap and shoulder belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the advanced front ...

  • Page 45

    Ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Driver and passenger beltalert (if equipped) beltalert is a feature intended to remind the driver and outboard front seat passenger (if equipped with outboard fron...

  • Page 46

    Driver and occupied outboard front seat passenger seat belts are buckled. The driver should instruct all occu- pants to buckle their seat belts. Change of status if the driver or outboard front seat passenger (if equipped with outboard front passenger seat beltalert) unbuckles their seat belt while ...

  • Page 47

    Will lock and reduce your risk of striking the inside of the vehicle or being thrown out of the vehicle. Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t ...

  • Page 48

    Warning! (continued) • two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. • a lap belt worn too high c...

  • Page 49

    Warning! (continued) your strongest bones will take the force in a colli- sion. • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to b...

  • Page 50

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 51

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automaticall...

  • Page 52

    3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Adjustable upper shoulder belt anchorage in the driver and...

  • Page 53

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton. To verify the shoulder belt anchorage is latched, pull downward on the shou...

  • Page 54

    3. Route the shoulder belt to the inside of the right head restraint. 4. When the seat belt is long enough to fit, insert the mini-latch plate into the mini-buckle until you hear a “click.” 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the seat belt t...

  • Page 55

    9. To release the seat belt, push the red button on the buckle. 10. To disengage the mini-latch plate from the mini- buckle for storage, insert the regular latch plate into the black button on the top of the mini-buckle. The seat belt will automatically retract to its stowed position. If necessary, ...

  • Page 56

    Warning! (continued) proper restraint and will increase the risk of injury in a collision. • when reattaching the mini-latch plate and mini- buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding procedure to detach the mini-latch plate and mini- buckle,...

  • Page 57

    Seat belts and pregnant women seat belts must be worn by all occupants including pregnant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong b...

  • Page 58

    The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately. Energy management feature this vehicle has a seat belt system with an energy manageme...

  • Page 59

    If the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt r...

  • Page 60

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the seat belt assembly must be replaced if the switchable automati...

  • Page 61

    The active head restraints (ahr) to deploy. If a rear impact requires deployment, both the driver and front passenger seat ahrs will be deployed. When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head an...

  • Page 62

    Warning! • all occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. • do not place items over the top of the active head restra...

  • Page 63

    Us llc dealer must reset the ahrs on the driver’s and front passenger’s seat before driving. Personally attempt- ing to reset the ahrs may result in damage to the ahrs that could impair their function. Warning! Deployed ahrs are not able to best protect you in all types of collisions. Have deployed ...

  • Page 64

    • supplemental side air bags • front and side impact sensors • seat belt pretensioners • seat belt buckle switch • seat track position sensors advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the seat belt restraint systems. ...

  • Page 65

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 66

    Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bags to inflate. • do not put anything on or around the air bag covers or attempt to op...

  • Page 67

    Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away f...

  • Page 68

    Supplemental side air bags your vehicle is equipped with two types of side air bags: 1. Supplemental seat-mounted side air bags (sabs): located in the outboard side of the front seats. The sabs are marked with a “srs airbag” or “air- bag” label sewn into the outboard side of the seats. The sabs may ...

  • Page 69

    Warning! Do not use accessory seat covers or place objects between you and the side air bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. 2. Supplemental side air bag inflatable curtains (sabics): located above the side windows. The tr...

  • Page 70

    Sabics may help reduce the risk of head or other injuries to front and rear seat outboard occupants in certain side impacts and/or vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. The sabics deploy downward, covering the side win- ...

  • Page 71

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 72

    Warning! (continued) properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note: air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. Side impacts in side impacts, the side impa...

  • Page 73

    Faster-developing event may deploy the seat belt preten- sioners as well as the side air bags on both sides of the vehicle. The rollover sensing-system may also deploy the seat belt pretensioners, with or without the side air bags, on both sides of the vehicle if the vehicle experiences a near rollo...

  • Page 74

    Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and th...

  • Page 75

    Enhanced accident response system reset procedure in order to reset the enhanced accident response system functions after an event, the ignition switch must be changed from ignition start or on/run to ignition off. Carefully check the vehicle for fuel leaks in the engine compartment and on the groun...

  • Page 76

    While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • the air bag warning light does not come on during the four to eight seconds when the ignition switch is first turned to the on/run position...

  • Page 77

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 78

    Assist in understanding how a vehicle’s systems per- formed. The edr is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The edr in this vehicle is designed to record such data as: • how various systems in your vehicle w...

  • Page 79

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 80

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in...

  • Page 81

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carrie...

  • Page 82

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 83

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 84

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 85

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 86

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 87

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to know before starting your vehicle 85.

  • Page 88

    Frequently asked questions about installing child seats with latch what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and ...

  • Page 89

    Frequently asked questions about installing child seats with latch can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt...

  • Page 90

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the ...

  • Page 91

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing child restraints...

  • Page 92

    Restraints with flexible, webbing mounted lower attach- ments can be installed in any rear seating position. Warning! Never use the same lower anchorage to attach more than one child restraint. If you are installing latch- compatible child restraints next to each other, you must use the seat belt fo...

  • Page 93

    3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 94

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 95

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • top tether anchorage symbol 2 things to know before starting your vehicle 93.

  • Page 96

    Frequently asked questions about installing child restraints with seat belts what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a for- ward facing child restraint? Weight limit of the child restraint always use the tet...

  • Page 97

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 98

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 99

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 100

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 101

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 102

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 103

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 104

    Unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • alwa...

  • Page 105

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 107: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 ▫ inside day/night mirror . . . . . . . . . . . . . . . .110 ▫ automatic dimming mirror — if equipped . . .110 ▫ outside mirror — driver side . . . . . . . . . . . .111 ▫ outside ...

  • Page 108

    䡵 voice command — if equipped . . . . . . . .145 ▫ voice command system operation . . . . . . . . .145 ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . .147 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . .151 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 109

    ▫ headlights on with wipers (available with automatic headlights only) . . . . . . . . . . . . .170 ▫ instrument panel dimming. . . . . . . . . . . . . . .171 ▫ map/reading lights . . . . . . . . . . . . . . . . . . .171 䡵 windshield wipers and washers . . . . . .172 ▫ windshield wiper operation . ....

  • Page 110

    ▫ using homelink . . . . . . . . . . . . . . . . . . . . .191 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . .191 ▫ troubleshooting tips . . . . . . . . . . . . . . . . . . .192 ▫ general information. . . . . . . . . . . . . . . . . . . .193 䡵 power sunroof — if equipped . . . . . ...

  • Page 111

    ▫ cargo tie-down loops . . . . . . . . . . . . . . . . .208 ▫ fold down speakers — if equipped . . . . . . . .209 䡵 rear window features . . . . . . . . . . . . . .210 ▫ rear window wiper/washer . . . . . . . . . . . . .210 ▫ rear window defroster . . . . . . . . . . . . . . . . .211 䡵 roof luggage ...

  • Page 112

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 113

    Note: this feature is disabled when the vehicle is moving in reverse. Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside mirror — driver side adjust the flat outs...

  • Page 114

    Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or...

  • Page 115

    When you are finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror. Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “rear window fea...

  • Page 116

    Uconnect phone — if equipped uconnect phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect phone allows you to dial a phone number with your mobile phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s audio ...

  • Page 117

    System at a time. The system is available in english, spanish, or french languages. Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle...

  • Page 118

    The radio display will be used for visual prompts from the uconnect phone such as “cell” or caller id on certain radios. Operation voice commands can be used to operate the uconnect phone and to navigate through the uconnect phone menu structure. Voice commands are required after most uconnect phone...

  • Page 119

    To activate the uconnect phone, simply push the phone button and follow the audible prompts for direc- tions. Uconnect phone sessions begin with a push of the phone button on the radio control head. Cancel command at any prompt, after the beep, you can say “cancel” and you will be returned to the ma...

  • Page 120

    For identification purposes, you will be prompted to give the uconnect phone a name for your mobile phone. Each mobile phone that is paired should be given a unique phone name. You will then be asked to give your mobile phone a priority level between one and seven, with one being the highest priorit...

  • Page 121

    • the system will prompt you to say the name of the person you want to call. • after the “ready” prompt and the following beep, say the name of the person you want to call. For example, you can say “john doe,” where john doe is a previ- ously stored name entry in the uconnect phonebook or downloaded...

  • Page 122

    The uconnect phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32 name phonebook accessible only in that language. In addition, if equipped and supported by your phone, uconnect phone...

  • Page 123

    • this downloaded phonebook cannot be edited or deleted on the uconnect phone. These can only be edited on the mobile phone. The changes are trans- ferred and updated to uconnect phone on the next phone connection. Edit uconnect phonebook entries note: editing phonebook entries is recommended when t...

  • Page 124

    To delete a uconnect phonebook entry using voice com- mands: 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say “phonebook delete.” 3. After you enter the phonebook delete menu, you will then be asked for the name of the entry that you wish to delete. You can ...

  • Page 125

    3. After confirmation, the phonebook entries will be deleted. Note: • only the phonebook in the current language is deleted. • automatic downloaded phonebook entries cannot be deleted or edited. List all names in the uconnect phonebook to hear a list of all names in the uconnect phonebook using voic...

  • Page 126

    Answer or reject an incoming call — no call currently in progress when you receive a call on your mobile phone, the uconnect phone will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. • push the phone button to accept the call. • to reject the call, push...

  • Page 127

    Place/retrieve a call from hold to put a call on hold: 1. Push the phone button until you hear a single beep. • this indicates that the call is on hold. • to bring the call back from hold, push and hold the phone button until you hear a single beep. Toggling between calls if two calls are in progres...

  • Page 128

    Call termination to end a call in progress: 1. Momentarily push the phone button. • only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically...

  • Page 129

    2. After the ignition is cycled to off, a call can continue on the uconnect phone for a certain duration, after which the call is automatically transferred from the uconnect phone to the mobile phone. 3. An active call is automatically transferred to the mobile phone after the ignition is cycled to ...

  • Page 130

    • after the “ready” prompt and the following beep, say “emergency” and the uconnect phone will instruct the paired mobile phone to call the emergency number. This feature is supported in the u.S., canada, and mexico. Note: • the emergency number dialed is based on the country where the vehicle is pu...

  • Page 131

    Note: you should program the desired towing assis- tance phone number using the voice command system. To do this, push the phone button and say “setup,” followed by “towing assistance.” when prompted say 1-800-521-2779 for u.S./canada, say 55-14-3454 for mexico city and 1-800-712-3040 for outside me...

  • Page 132

    Used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored uconnect phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to call and then pus...

  • Page 133

    2. After the “ready” prompt and the following beep, say one of the following: • “setup confirmation prompts on” • “setup confirmation prompts off” phone and network status indicators if available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your mob...

  • Page 134

    To un-mute the uconnect phone: • push the voice command button. • following the beep, say “mute off.” advanced phone connectivity transfer call to and from mobile phone the uconnect phone allows ongoing calls to be trans- ferred from your mobile phone to the uconnect phone without terminating the ca...

  • Page 135

    • the uconnect phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, push the voice command but- ton and say “select” or “delete.” also, see the next two sections for an alternate way to “...

  • Page 136

    Things you should know about your uconnect phone uconnect phone tutorial to hear a brief tutorial of the system features, push the phone button and say “uconnect tutorial.” voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect ph...

  • Page 137

    • this will delete all phone pairing, phone book en- tries, and other settings in all language modes. The system will prompt you before resetting to factory settings. Voice command for best performance: • adjust the rearview mirror to provide at least ½ inch (1 cm) gap between the overhead console (...

  • Page 138

    • storing names in the phonebook when the vehicle is not in motion is recommended. • it is not recommended to store similar sounding names in the uconnect phonebook. • phonebook (downloaded and uconnect phone local) name recognition rate is optimized when the entries are not similar. • numbers must ...

  • Page 139

    Recent calls if your phone supports “automatic phonebook down- load,” uconnect phone can list your outgoing, incoming and missed calls. Voice text reply uconnect phone can read or send new messages on your phone. Read messages: if you receive a new text message while your phone is connected to uconn...

  • Page 140

    “send.” uconnect phone will prompt you to say the name or number of the person you wish to send the message to. List of preset messages: 1. Yes. 2. No. 3. Where are you? 4. I need more direction. 5. L o l. 6. Why? 7. I love you. 8. Call me. 9. Call me later. 10. Thanks. 11. See you in 15 minutes. 12...

  • Page 141

    Turn voice text reply incoming announcement on/ off turning the voice text reply incoming announcement off will stop the system from announcing the new incoming messages. To turn voice text reply incoming announcement on or off using voice command: 1. Push the phone button. 2. After the “ready” prom...

  • Page 142

    140 understanding the features of your vehicle.

  • Page 143

    3 understanding the features of your vehicle 141.

  • Page 144

    142 understanding the features of your vehicle.

  • Page 145

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help 3 understanding the features...

  • Page 146

    Primary alternate (s) home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again primary alternate (s) redial return to main menu return or main menu select phone select send set up phone settings or phon...

  • Page 147

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 148

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When y...

  • Page 149

    At any point, if the system does not recognize one of your commands, you will be prompted to repeat it. To hear the first available menu, push the voice com- mand button and say “help” or “main menu.” commands the voice command system understands two types of commands, universal commands and local c...

  • Page 150

    • “bluetooth streaming” (to switch to bluetooth stream- ing mode) • “memo” (to switch to the memo recorder) • “system setup” (to switch to system setup) radio am to switch to the am band, say “am” or “radio am.” in this mode, you may say the following commands: • “frequency #” (to change the frequen...

  • Page 151

    Satellite radio to switch to satellite radio mode, say “sat” or “satellite radio.” in this mode, you may say the following com- mands: • “channel number” (to change the channel by its spoken number) • “next channel” (to select the next channel) • “previous channel” (to select the previous channel) •...

  • Page 152

    Bluetooth streaming (bt) mode to switch to bluetooth streaming (bt) mode, say “bluetooth streaming.” in this mode, you may say the following commands: • “play” (to play the current track) • “pause” (to pause the current track) • “next track” (to play the next track) • “previous track” (to play the p...

  • Page 153

    Setup to switch to system setup, you may say one of the following: • “change to setup” • “switch to system setup” • “main menu setup” • “switch to setup” in this mode, you may say the following commands: • “language english” • “language french” • “language spanish” • “tutorial” • “voice training” no...

  • Page 154

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 155

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 156

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the center instrument panel area. You can choose from hi, lo or off heat settings. Amber indica...

  • Page 157

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Man...

  • Page 158

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 159

    Manual lumbar — if equipped the lumbar adjustment handle is located on the inboard or outboard side of the seatback. Rotate the lever down- ward to increase the lumbar support or rotate the lever upward to decrease the lumbar support. Driver’s seatback recline to adjust the seatback, lift the lever ...

  • Page 160

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Head restraints head restraints are designed to reduce the risk of injury by restricti...

  • Page 161

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 162

    For comfort the active head restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Note: • the head ...

  • Page 163

    • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head restraints (ahr)” in “things to know before starting your vehicle” for further information. Warning! • all occupants, including the driver, should not operate a vehicle or sit in a vehicle...

  • Page 164

    Folding rear seat to provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to fold the rear seatback flat. To raise the seatback, pull the strap forward and lift the seatback into its upright position. Rear seat release straps folded rear seat 162 understa...

  • Page 165

    Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Reclining rear seat — if equipped for ...

  • Page 166

    To open and close the hood to open the hood, two latches must be released. 1. Pull the hood release lever located on the left kick panel. 2. Move the safety catch located under the front edge of the hood, near the center and raise the hood. Lift the hood prop rod, clipped to the right side (left sid...

  • Page 167

    Caution! To prevent possible damage: • before closing hood, make sure the hood prop rod is fully seated into its storage retaining clips. (continued) caution! (continued) • do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches eng...

  • Page 168

    Lights multifunction lever the multifunction lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and the fog lights. The multifunction lever is located on the left side of the ste...

  • Page 169

    Headlights and parking lights turn the end of the multifunction lever to the first detent to turn on the parking lights. Turn the end of the lever to the second detent to turn on the headlights. Automatic headlights — if equipped turning the end of the multifunction lever to the third detent (auto),...

  • Page 170

    With the engine running and the multifunction lever in the auto position, the headlights will turn on and turn off based on the surrounding light levels. Daytime running lights — if equipped the high beam lights will come on as daytime running lights (lower intensity), whenever the ignition is on, t...

  • Page 171

    Note: the fog lights will only operate with the head- lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn ...

  • Page 172

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/low beam switch push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction le...

  • Page 173

    Instrument panel dimming rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument pane...

  • Page 174

    Light off. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the second detent. Note: the lights will remain on until the switch is pushed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatical...

  • Page 175

    Caution! • turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • in cold weather, always turn off the wiper switch and allow the wipers to return to the “park” posi- tion be...

  • Page 176

    Windshield wiper operation rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper operation. Intermittent wiper system use the i...

  • Page 177

    While the lever is pulled and for two wipe cycles after the lever is released, and then resume the intermittent inter- val previously selected. If the lever is pulled while in the off position, the wipers will operate for two wipe cycles, then turn off. Warning! Sudden loss of visibility through the...

  • Page 178

    Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Tilt steering column this feature allows you to tilt the steering column upward or downward. The ...

  • Page 179

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause (continued) warning! (continued) the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or...

  • Page 180

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 181

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 182

    The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “under- standing your instrument panel” for more information. The speed increment shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pushing the res (+)...

  • Page 183

    The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “under- standing your instrument panel” for more information. The speed decrement shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pushing the set (-)...

  • Page 184

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 185

    The vehicle. The following table shows the approximate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 3 ft (30 cm - 1 m) green 3 ft or greater (1 m or greater) warning! Drivers must be careful when backing up even when using the parkview rear...

  • Page 186

    Note: if snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Garage door opener — if equipped homelink replaces up to three hand-held transmitters that operate devices such as garage door openers, ...

  • Page 187

    Homelink buttons/sunvisor/headliner note: homelink is disabled when the vehicle security alarm is active. Before you begin programming homelink be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the ra...

  • Page 188

    Programming a rolling code for programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “learn” or “train” button located where the hanging antenna is attached to the garage door opener. It is not the button that is normally used to open...

  • Page 189

    2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink button you wish to program while keeping the homelink indicator light in view. 3. Push and hold the homelink button you want to program while you push and hold the hand-held transmitter button. 4. Continue to hold bo...

  • Page 190

    Reprogramming a single homelink button (rolling code) to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Push and hold the desired homelink button until the indicator light begins to flash after 20 seconds. Do not release the...

  • Page 191

    5. Push and hold the programmed homelink button and observe the indicator light. • if the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the homelink button is pushed. • to program the two remaining homelink buttons, repeat each step fo...

  • Page 192

    It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. 1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink button you wish to program while keepi...

  • Page 193

    Reprogramming a single homelink button (canadian/gate operator) to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Push and hold the desired homelink button until the indicator light begins to flash after 20 seconds. Do not r...

  • Page 194

    Troubleshooting tips if you are having trouble programming homelink, here are some of the most common solutions: • replace the battery in the garage door opener hand- held transmitter. • push the learn button on the garage door opener to complete the training for a rolling code. • did you unplug the...

  • Page 195

    General information this device complies with part 15 of the fcc rules and with industry canada licence-exempt rss standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including...

  • Page 196

    Warning! (continued) fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • in a collision, ther...

  • Page 197

    Position. The sunroof will close fully and stop automati- cally. This is called “express close.” during express close operation, any other actuation of the switch will stop the sunroof. Closing sunroof — manual mode to close the sunroof, push and hold the switch in the forward position. Any release ...

  • Page 198

    Open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buff...

  • Page 199

    Power is available when the ignition switch is in the on or acc position. Insert the cigar lighter or accessory plug into the outlet for use. To preserve the heating element, do not hold the lighter in the heating position. Note: to ensure proper operation a mopar knob and element must be used. Caut...

  • Page 200

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 201

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 202

    Warning! To avoid serious injury or death: • do not use a three-prong adaptor. • do not insert any objects into the receptacles. (continued) warning! (continued) • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure...

  • Page 203

    Caution! (continued) • accessories that draw higher power (i.E., coolers, vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly. Only use these intermit- tently and with great caution. • after the use of high power draw accessories, or long periods of the vehicle not being star...

  • Page 204

    There are two cupholders located in the back for the rear passengers. Storage glove compartment and storage bin located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. Rear cupholders storage bins 1 — upper storage bin 2 — lower glove compartment...

  • Page 205

    To open the lower glove compartment, pull outward on the release handle. Door storage the interior door panels are equipped with lower storage areas. Glove compartment front door storage 3 understanding the features of your vehicle 203.

  • Page 206

    Console features the floor console contains both an upper and lower storage compartment. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. Rear door storage upper storage compartment 204 understanding the features of your vehicle.

  • Page 207

    To open the lower storage compartment, lift upward on the lower handle to unlatch the lower storage compart- ment and lift the lid open. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a...

  • Page 208

    To install the cargo cover, insert either end of the cover into one of the two notches located in the rear trim panels. With one of the cover ends installed, push inward on the opposite end and install it into the same notch location of the rear trim panel. Using the handle, pull the cover toward yo...

  • Page 209

    Warning! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. Do...

  • Page 210

    Cargo tie-down loops there are four tie-downs (d-rings) installed in the cargo area for securing cargo. Warning! • cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be b...

  • Page 211

    Warning! (continued) • place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be...

  • Page 212

    Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the center portion of the control lever. The control lever is located on the right side of the steering column. Rotate the center portion of the lever upward to the first detent position f...

  • Page 213

    Note: the rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to operate as long as the switch is held (for a maximum of 10 seconds). Upon release, the wiper will conti...

  • Page 214

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 215

    The crossbars must also be secured in one of the seven detent positions marked with an arrow on the siderails to prevent movement. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately eight turns, then move the crossbar to the desired position, keep...

  • Page 216

    Caution! (continued) • long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof ra...

  • Page 217: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .218 䡵 instrument cluster . . . . . . . . . . . . . . . . .219 䡵 warning and indicator lights . . . . . . .223 ▫ red telltale indicator lights . . . . . . . . . . . . . .224 ▫ yellow telltale indicator lights ...

  • Page 218

    ▫ display units of measure in . . . . . . . . . . . . .254 ▫ personal settings (customer-programmable features) . . . . . . . . . . . . . . . . . . . . . . . . . . .254 䡵 uconnect 230 – am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 219

    ▫ operation instructions — cd mode for cd and mp3 audio play . . . . . . . . . . . . . . . . . . . . . .296 ▫ notes on playing mp3 files . . . . . . . . . . . . .298 ▫ list button — cd mode for mp3 play. . . . . .301 ▫ info button — cd mode for mp3 play . . . . .301 ▫ uconnect (satellite radio) — if...

  • Page 220

    Instrument panel features 1 — air outlet 5 — storage bin 9 — heated seat switch – if equipped 2 — demisters 6 — glove compartment 10 — hazard warning flasher 3 — instrument cluster 7 — climate controls 11 — esc off switch – if equipped 4 — radio 8 — power outlet 12 — heated seat switch – if equipped...

  • Page 221

    Instrument cluster 4 understanding your instrument panel 219.

  • Page 222

    1. Speedometer • the speedometer shows the vehicle speed in miles per hour (mph) and kilometers per hour (km/h). Odometer display / trip odometer display this display indicates the total distance the vehicle has been driven. Note: u.S. Federal regulations require that upon trans- fer of vehicle owne...

  • Page 223

    Caution! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h”, turn the engine ...

  • Page 224

    Message display area when the appropriate conditions exist, the following odometer messages will display: door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door ajar gate . . . . . . . . . . . . . . . . . . . . . . . . . . Liftgate ajar low tire . . . . . . . . . . . . . . . . . . . . L...

  • Page 225

    Nofuse if the vehicle diagnostic system determines that the ignition off draw (iod) fuse is improperly installed, or damaged, a “nofuse” message will display in the odometer display area. Refer to “fuses” in “maintaining your vehicle” for further information on fuses and fuse locations. Change oil y...

  • Page 226

    Red telltale indicator lights seat belt reminder warning light red telltale light what it means seat belt reminder warning light when the ignition switch is first turned to on/run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is ...

  • Page 227

    Air bag warning light red telltale light what it means air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during startup, stays on, or turns on while driving, have the system inspec...

  • Page 228

    Brake warning light red telltale light what it means united states canada brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid le...

  • Page 229

    The light will remain on until the cause is corrected. Note: the light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces...

  • Page 230

    Vehicle security warning light — if equipped red telltale light what it means vehicle security warning light — if equipped this light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. Oil pressu...

  • Page 231

    Engine temperature warning light red warning light what it means engine temperature warning light this light warns of an overheated engine condition. As engine coolant temperatures rise and the gauge approaches h , this indicator will illuminate and a single chime will sound after reaching a set thr...

  • Page 232

    Oil temperature warning light red telltale light what it means oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Charging system warning light red telltale light wha...

  • Page 233

    Electronic throttle control (etc) warning light red telltale light what it means electronic throttle control (etc) warning light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected while the engine is running, the light will either stay on ...

  • Page 234

    Yellow telltale indicator lights engine check/malfunction indicator light (mil) yellow telltale light what it means engine check/malfunction indicator light (mil) the engine check/malfunction indicator light (mil) is a part of an onboard diagnostic system called obd ii that monitors engine and autom...

  • Page 235

    Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warni...

  • Page 236

    Tire pressure monitoring indicator light yellow telltale light what it means tire pressure monitoring indicator light the warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these ...

  • Page 237

    Important: do not continue driving with one or more flat tires as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. Repair immediately using the dedicated tire repair kit and contact your authorized dealership as soon as possible. Each tire, including the spare (if ...

  • Page 238

    Illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur for a variety of reasons, includi...

  • Page 239

    Electronic stability control (esc) off indicator light — if equipped yellow telltale light what it means electronic stability control (esc) off indicator light — if equipped this light indicates the electronic stability control (esc) is off. 4 understanding your instrument panel 237.

  • Page 240

    Electronic stability control (esc) indicator light — if equipped yellow telltale light what it means electronic stability control (esc) indicator light — if equipped the “esc indicator light” in the instrument cluster will come on when the ignition switch is turned to the on/run position. It should ...

  • Page 241

    Anti-lock brake (abs) indicator light yellow telltale light what it means anti-lock brake (abs) indicator light this light monitors the anti-lock brake system (abs). The light will turn on when the igni- tion switch is placed in the on/run position and may stay on for as long as four seconds. If the...

  • Page 242

    Low fuel warning indicator light yellow telltale light what it means low fuel warning indicator light when the fuel level reaches approximately 2.8 gal (10.6 l), this light will turn on and a single chime will sound. 4wd! Warning light — if equipped yellow tell- tale light what it means 4wd! Warning...

  • Page 243

    Loose fuel filler cap indicator light — if equipped yellow telltale light what it means loose fuel filler cap indicator light — if equipped this light will illuminate when fuel filler cap is loose. Properly close the filler cap to disen- gage the light. If the light does not turn off, please see you...

  • Page 244

    Transmission temperature indicator light yellow tell- tale light what it means transmission temperature indicator light this light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and ...

  • Page 245

    Green telltale indicator lights turn signal indicator lights green tell- tale light what it means turn signal indicator lights the instrument cluster directional arrow will flash independently for the left or right turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear)...

  • Page 246

    Park/headlight on indicator light green telltale light what it means park/headlight on indicator light this indicator will illuminate when the park lights or headlights are turned on. Front fog indicator light — if equipped green telltale light what it means front fog indicator light — if equipped t...

  • Page 247

    Blue telltale indicator lights high beam indicator light blue telltale light what it means high beam indicator light this indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switc...

  • Page 248

    Hill descent indicator light — if equipped white tell- tale light what it means hill descent indicator light — if equipped this indicator shows when the hill descent control (hdc) feature is turned on. The lamp will be on solid when hdc is armed. Hdc can only be armed when the transfer case is in th...

  • Page 249

    Control buttons step button push the step button located on the steering wheel to scroll through sub menus (i.E., temperature, trip func- tions: odometer, trip a, trip b). Reset button to reset the display shown, turn the ignition switch to the on position, then push and hold the reset button locate...

  • Page 250

    Trip b shows the total distance traveled for trip b since the last reset. Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following:...

  • Page 251

    • personal settings (customer-programmable features) • compass heading • outside temperature display • trip computer functions • uconnect phone displays (if equipped) • audio mode display • tire pressure monitor (tpm) the system allows the driver to select information by pushing the following button...

  • Page 252

    Compass button push and release the compass button to display one of eight compass readings and the outside temperature or to exit sub-menus. Right arrow button push and release the right arrow button for access to main menus, submenus, or to select a personal setting in the setup menu. Down arrow b...

  • Page 253

    • gate (with vehicle graphic showing the liftgate open and a single chime) • headlamps or park lamps on • remote start aborted — door ajar • remote start aborted — hood ajar • remote start aborted — l/gate ajar • remote start aborted — fuel low • remote start aborted — system fault • key in ignition...

  • Page 254

    1. Turn the ignition switch to the on position. Do not start the engine. 2. Fully push the accelerator pedal, slowly, three times within 10 seconds. 3. Turn the ignition switch to the off/lock position. Note: if the indicator message illuminates when you start the vehicle, the oil change indicator s...

  • Page 255

    Refer to “personal settings (customer-programmable features)” in this section for additional information re- garding the compass. Average fuel economy shows the average fuel economy since the last reset (pushing and holding the right arrow button as prompted in the evic display to reset). When the f...

  • Page 256

    Elapsed time shows the total elapsed time of travel since the last reset. Elapsed time will increment when the ignition switch is in the run/start position. Elapsed time is displayed as follows: hours: minutes: seconds elapsed time can be reset by pushing and holding the right arrow button (as promp...

  • Page 257

    Francais, or nl depending on availability. As you continue, the displayed information will be shown in the selected language. Note: uconnect language will not change using the evic. Please refer to “uconnect phone features” in “understanding the features of your vehicle” for fur- ther information. A...

  • Page 258

    Without the sound horn with lock feature selected. Push and hold the right arrow button when in this display until “on” or “off” appears to make your selection. Sound horn with lock when on is selected, a short horn sound will occur when the rke transmitter lock button is pushed. This feature may be...

  • Page 259

    Either front vehicle door will cancel this feature. Push and hold the right arrow button when in this display until “off,” “45 sec.”, “5 min.”, or “10 min.” appears to make your selection. Illuminated approach when this feature is selected, the headlights will activate and remain on for up to 90 sec...

  • Page 260

    Note: a good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc. Manual compass calibration if the compass appears erratic and the “cal” indicator does not appear in the evic display, you must ...

  • Page 261

    Note: magnetic materials should be kept away from the top of the right rear quarter window. This is where the compass sensor is located. 1. Turn the ignition switch on. 2. Push and hold the compass button for approxi- mately two seconds. 3. Push and release the down arrow button until “compass varia...

  • Page 262

    Uconnect 230 – am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/...

  • Page 263

    Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations witho...

  • Page 264

    Time button push the time button to alternate locations of the time and frequency display. Clock setting procedure 1. Push and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, push the right side tune/ ...

  • Page 265

    Setting the tone, balance and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control ...

  • Page 266

    Toggle the music type button to select the following format types: program type 16-digit character dis- play no program type or un- defined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news ne...

  • Page 267

    By pushing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the ...

  • Page 268

    • angle — repeatedly pushing select will change the viewing angle if supported by the dvd disc (if equipped). Note: • the available selections for each of the above entries varies depending upon the disc. • these selections can only be made while playing a dvd. • power — allows you to turn the power...

  • Page 269

    Audio language — if equipped selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙ other. ⬙ enter the country code using the tune/scroll control knob to scrol...

  • Page 270

    Note: the user will have to set these defaults before loading a disc. If changes are made to these settings after a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings. Am and fm buttons push the buttons to select ...

  • Page 271

    Disc button pushing the disc button will allow you to switch from am/fm modes to disc modes. Operation instructions — disc mode for cd and mp3/wma audio play, dvd – video the radio dvd player and many dvd discs are coded by geographic region. These region codes must match for the disc to play. If th...

  • Page 272

    Caution! This cd player will accept 4–3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. Eject button — ejecting compact disc(s) push the eject button and the pushbutton with the corresponding number (1-6) where the cd was loaded and the disc will unload an...

  • Page 273

    Rw/ff (cd mode) push and hold ff (fast forward) and the cd player will begin to fast forward until ff is released, or rw or another cd button is pushed. The rw (rewind) button works in a similar manner. Am or fm button (cd mode) switches the radio into the am or fm radio mode. Notes on playing mp3/w...

  • Page 274

    Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal cd audio tracks and computer files (including mp3/ wma files). Discs created with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs. The use of multisession...

  • Page 275

    Wma specifi- cation sampling fre- quency (khz) bit rate (kbps) wma 44.1 and 48 48, 64, 96, 128, 160, 192 vbr id3 tag information for artist, song title, and album title are supported for id3 version 1 tags. Id3 version 2 is not supported by the radios. Playlist files are not supported. Mp3 pro files...

  • Page 276

    List button — disc mode for mp3/wma play pushing the list button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the tune/scroll control knob. Selecting a folder by pushing the tune/scroll control knob will begin playing the files contained in that f...

  • Page 277

    Scan button (auxiliary mode) no function. Eject button (auxiliary mode) no function. Time button (auxiliary mode) push the time button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Rw/ff (auxiliary mode) no function. Set button (auxili...

  • Page 278

    Intended for home and other limited viewing uses only, unless otherwise authorized by macrovision. Reverse engineering or disassembly is prohibited. Dts “dts and “dts 2.0” are trademarks of digital theater systems, inc. Uconnect (satellite radio) — if equipped satellite radio uses direct satellite-t...

  • Page 279

    To access the esn/sid, refer to the following steps: esn/sid access with the ignition switch in the on/run or acc posi- tion and the radio on, push the setup button and scroll using the tune/scroll control knob until sirius id is selected. Push the tune/scroll control knob and the sirius id number w...

  • Page 280

    Operating instructions — uconnect (satellite) mode note: the ignition switch must be in the on/run or acc position to operate the radio. Seek buttons push and release the seek buttons to search for the next listenable station in am/fm mode. Push the right switch to seek up and the left switch to see...

  • Page 281

    Music type button pushing this button once will turn on the music type mode for five seconds. Pushing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Toggle the music type button again to select the music type. By...

  • Page 282

    You may add a second channel to each pushbutton by repeating the above procedure with this exception: push the set button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2. This allows a total of 12 satellite channels to be stored into pushbutton memory. The...

  • Page 283

    Uconnect 130 operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electroni...

  • Page 284

    Another selection. Holding either button will bypass stations without stopping, until you release it. Time button push the time button to alternate display of the time and radio frequency. Clock setting procedure 1. Push and hold the time button until the hours blink. 2. Adjust the hours by turning ...

  • Page 285

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 286

    Display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pushing the pushbutton twice. Every time a preset button is used, a corresponding ...

  • Page 287

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 288

    The current selection. Pushing and holding the seek button will allow faster scrolling through the tracks in cd and mp3 modes. Time button push this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff push and hold the ff (fast forward) button ...

  • Page 289

    Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded using formats other than iso 9660 level 1 and level 2, the radio may fail to read files properly and may be unable to play...

  • Page 290

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 291

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 292

    Uconnect 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off...

  • Page 293

    Another selection. Holding either button will bypass stations without stopping, until you release it. Voice command system (radio) — if equipped refer to “voice command” in “understanding the fea- tures of your vehicle”. Voice command button uconnect phone — if equipped push this button to operate t...

  • Page 294

    3. After adjusting the hours, push the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Push the tune/scroll con- trol knob to save time change. 5. To exit, push any button/knob or wait fiv...

  • Page 295

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 296

    Program type 16-digit character display classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news nostalgia nostalga oldies oldies personality persnlty public public rhythm and blues r & b religious music rel musc progra...

  • Page 297

    If a preset button is activated while in the music type (program type) mode, the music type mode will be exited and the radio will tune to the preset station. Setup button pushing the setup button allows you to select between the following items: • set clock — pushing the select button will allow yo...

  • Page 298

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory (12 am and 12 fm stations). Disc/aux button pushing the disc/aux button will allow you to switch from am/fm modes to disc/au...

  • Page 299

    Caution! • this cd player will accept 4–3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • the uconnect 130 is a single cd player. Do not attempt to insert a second cd ...

  • Page 300

    Rw/ff push and hold ff (fast forward) and the cd player will begin to fast forward until ff is released or rw or another cd button is pushed. The rw (reverse) button works in a similar manner. Am/fm button push the button to select either am or fm mode. Set/rnd button (random play button) push this ...

  • Page 301

    The radio uses the following limits for file systems: • maximum number of folder levels: 8 • maximum number of files: 255 • maximum number of folders. (the radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file ...

  • Page 302

    Use a 44.1 khz sampling rate and a 192, 160, 128, 96 or vbr bit rates. Mpeg specifi- cation sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56...

  • Page 303

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button — cd mode for mp3 play pushing the list button will bring up a list of all folders on the dis...

  • Page 304

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Time button (auxiliary mode) push this button to change the display to time of d...

  • Page 305

    Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic serial number/sirius identification number (esn/sid). 2. Your vehicle identification number. To access the esn/sid, refer to the following steps: esn/sid ac...

  • Page 306

    • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or along tall buildings can cause intermittent reception. • placing objects over or too close to the antenna can cause signal blockage. Operating instructions — uconnect (satellite) mode note...

  • Page 307

    Rw/ff pushing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) turn the rotary tune/scroll control knob clockwise to increase or counterclockwise to decrease the channel. Music type button pushing this ...

  • Page 308

    Set button — to set the pushbutton memory when you are receiving a channel that you wish to commit to pushbutton memory, push the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and push and release that button. If a button...

  • Page 309

    Ipod control supports mini, 4g, photo, nano, 5g ipod and iphone devices. Some ipod software versions may not fully support the ipod control features. Please visit apple’s website for software updates. Note: • if the radio has a usb port, refer to the appropriate uconnect multimedia radio user’s manu...

  • Page 310

    Note: if the audio device battery is completely dis- charged, it may not communicate with the ipod/usb/ mp3 control system until a minimum charge is attained. Leaving the audio device connected to the ipod/usb/ mp3 control system may charge it to the required level. Using this feature by using an ex...

  • Page 311

    • turning it clockwise (forward) by one click, while playing a track, skips to the next track or push the vr button and say ⬙ next track. ⬙ • turning it counterclockwise (backward) by one click, will jump to the previous track in the list or push the vr button and say ⬙ previous track. ⬙ • jump back...

  • Page 312

    Scan button again. During scan mode, pushing the seek and seek >> buttons will select the previous and next tracks. • rnd button (available on sales code res radio only): pushing this button toggles between shuffle on and shuffle off modes for the ipod or external usb device, or push the vr button a...

  • Page 313

    In list mode, the radio preset buttons are used as shortcuts to the following lists on the ipod or external usb device: • preset 1 – playlists • preset 2 – artists • preset 3 – albums • preset 4 – genres • preset 5 – audiobooks • preset 6 – podcasts pushing a preset button will display the current l...

  • Page 314

    Caution! • leaving the ipod or external usb device (or any supported device) anywhere in the vehicle in ex- treme heat or cold can alter the operation or dam- age the device. Follow the device manufacturer’s guidelines. • placing items on the ipod or external usb device, or connections to the ipod o...

  • Page 315

    Selecting a different audio device 1. Push the phone button to begin. 2. After the ⬙ ready ⬙ prompt and following the beep, say ⬙ setup ⬙ , then say ⬙ select audio devices. ⬙ 3. Say the name of the audio device or ask the uconnect phone system to list the audio devices. Next track use the seek up bu...

  • Page 316

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a push-button in the center and controls the volume and mode of the sound system. P...

  • Page 317

    Radio operation pushing the top of the switch will “seek” up for the next listenable station and pushing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gramme...

  • Page 318

    4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Note: if you experience difficulty in playing a particular dis...

  • Page 319

    Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and inner push knobs. Blower control rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control...

  • Page 320

    Note: if your air conditioning performance seems lower than expected, check the front of the a/c condenser located in front of the radiator for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may r...

  • Page 321

    The closer the setting is to a particular symbol, the more air distribution you receive from that mode. • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center instrument panel outlets can be aimed so that they are dire...

  • Page 322

    Note: • the air conditioning compressor operates in mix, defrost, or a blend of these modes, even if the air conditioning (a/c) button is not pushed. This dehu- midifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary. • for information on operating t...

  • Page 323

    Automatic temperature control (atc) — if equipped the automatic temperature control system automati- cally maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. Automatic operation operation of the system is quite simple. 1. Turn the mode contro...

  • Page 324

    You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting the “o” (off) position on the blower control stops the system completely and closes the outside air intake. The recommended setting for maximum comfort for the average person is 72°f (22°c)...

  • Page 325

    Blower control for full automatic operation or for automatic blower operation, turn the blower knob to the auto position. In manual mode there are seven blower speeds that can be individual selected. In off position the blower will shut off. Manual operation override this system offers a full comple...

  • Page 326

    324 understanding your instrument panel.

  • Page 327

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center ...

  • Page 328

    • air conditioner control push this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Push this but- ton a second time to turn off the air conditioning....

  • Page 329

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pushing the recirculation button. However, under certain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the rec...

  • Page 330

    Adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window fogging interior fogging on the windshield can be quickly re- moved by turning the mode selector to defrost. The defrost/floor mode can be used to maintain a clear windshield and pro...

  • Page 331

    Control setting suggestions for various weather conditions 4 understanding your instrument panel 329.

  • Page 333: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .335 ▫ manual transmission — if equipped . . . . . . .335 ▫ automatic transmission — if equipped . . . . .336 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .336 ▫ extreme cold weather (below –22°f or −...

  • Page 334

    䡵 autostick . . . . . . . . . . . . . . . . . . . . . . . . . .355 ▫ autostick (six-speed automatic transmission) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .355 ▫ autostick (cvt) — if equipped . . . . . . . . . . .357 䡵 four-wheel drive operation — if equipped . . . . . . . . . ....

  • Page 335

    ▫ electronic roll mitigation (erm) . . . . . . . . . .386 ▫ hill descent control (hdc) — if equipped . . .387 䡵 tire safety information . . . . . . . . . . . . .388 ▫ tire markings . . . . . . . . . . . . . . . . . . . . . . . .388 ▫ tire identification number (tin). . . . . . . . . . .392 ▫ tire te...

  • Page 336

    䡵 fuel requirements . . . . . . . . . . . . . . . . . .424 ▫ 2.0l and 2.4l engine . . . . . . . . . . . . . . . . . . .424 ▫ reformulated gasoline . . . . . . . . . . . . . . . . .424 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . .425 ▫ e-85 usage in non-flex fuel vehicles . . . . . . .425 ▫...

  • Page 337

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • before exiting a vehicle, always shift the transmis- sion into park, apply the parking brake and remove the key fob from the ignition. When leaving the v...

  • Page 338

    Automatic transmission — if equipped the shift lever must be in the park or neutral position before you can start the engine. Press the brake pedal before shifting to any driving gear. Note: you must press the brake pedal before shifting out of park. Tip start do not press the accelerator. Turn the ...

  • Page 339

    Warning! (continued) another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. Refer to “jump-starting” in “what to do in emer- gencies” for further information. Extreme cold weather (below –22°f or −30°c) to ensure reliable starting at these tempera...

  • Page 340

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 341

    Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in a gear higher than first gear. Caution! • launching in any gear except 1st gear will result in excess...

  • Page 342

    Never shift into reverse until the vehicle has come to a complete stop. Note: during cold weather, until the transmission lu- bricant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the transmis- sion. Recommended shift speeds to use your manual transmiss...

  • Page 343

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 344

    Note: you must press and hold the brake pedal while shifting out of park. Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You c...

  • Page 345

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. The key can only be re- moved from the ignition when the ignition is in the lock/o...

  • Page 346

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has only park, reverse, neutral, and drive shift positions. Manual shifts can be ma...

  • Page 347

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not in park. Check by trying to move the gear...

  • Page 348

    Warning! (continued) warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the ignition key in or near the vehicle (or in a location accessible to children). A child could operate power windows, other controls, or move the vehicle. Caution! • before moving the gear ...

  • Page 349

    Neutral (n) use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift the transmission into park if you must leave the vehicle. Warning! Do not coast in neutral and never turn off the ignition...

  • Page 350

    Control (refer to “autostick (six-speed automatic trans- mission)” in this section for further information) to select a lower gear. Under these conditions, using a lower gear will improve performance and extend transmission life by reducing excessive shifting and heat buildup. If the transmission te...

  • Page 351

    In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following steps: 1. Stop the vehicle. 2. Shift the transmission into park. 3. Turn the ignition switch to the off position. 4. Wait approximately 10 seconds. 5. Restart the engine. 6. Shi...

  • Page 352

    Torque converter clutch a feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati- cally at calibrated speeds. This may result in a slightly different feeling or response during normal operation i...

  • Page 353

    The transmission shift lever only has park, reverse, neutral, and drive shift positions. Manual shifts can be made using the autostick shift control (refer to ⬙ autostick ⬙ in this section). Moving the shift lever to the left or right (-/+) while in the drive position will manually select from a set...

  • Page 354

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not in park. Check by trying to move the gear...

  • Page 355

    Warning! (continued) warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the ignition key in or near the vehicle (or in a location accessible to children). A child could operate power windows, other controls, or move the vehicle. Caution! • before moving the gear ...

  • Page 356

    Neutral (n) use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift the transmission into park if you must leave the vehicle. Warning! Do not coast in neutral and never turn off the ignition...

  • Page 357

    When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading condi- tions, in hilly terrain, traveling into strong head winds, or while towing heavy trailers), use the autostick shift control (if equipped, refer to “autostick (cvt)” in this section for further i...

  • Page 358

    (+) to enter autostick mode will retain the current gear. When autostick is active, the current transmission gear is displayed in the instrument cluster. In autostick mode, the transmission will shift up or down when the driver moves the shift lever to the right (+) or left (-), unless an engine lug...

  • Page 359

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Autostick (cvt) — if equipped autostick is a driver-interactive transmission feature providing six manually select...

  • Page 360

    In autostick mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result. It will remain in the selected gear until another upshift or downshift is chosen, except as described below: • the transmission will ...

  • Page 361

    Four-wheel drive operation — if equipped this feature provides full time, on-demand, four–wheel drive (4wd). Where one or more wheels have wheel spin or if addi- tional traction is needed in sand, deep snow, or loose traction surfaces, activate the “4wd lock” switch by pulling up once and releasing....

  • Page 362

    An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfacto- rily in off-road cond...

  • Page 363

    Warning! Always wear your seat belt and firmly tie down cargo. Unsecured cargo can become projectiles in an off-road situation. When to use low (l off-road) with the 4wd lock lever engaged — if equipped when driving off-road, shift into low (l off-road [if equipped] ) and activate the 4wd lock. This...

  • Page 364

    Headway. Over-revving the engine can spin the wheels and traction will be lost. If you start to slow to a stop, try turning your steering wheel no more than a 1/4 turn quickly back and forth, while still applying throttle. This will allow the tires to get a fresh ⬙ bite ⬙ and help maintain your mome...

  • Page 365

    Engaged and esc turned off. Reduced tire pressure will drastically improve your traction and handling, while driving on the soft sand, but you must return the tires to normal air pressure before driving on pavement or other hard surfaces. Be sure you have a way to reinflate the tires prior to reduci...

  • Page 366

    Up for the straightest possible run. Accelerate with an easy constant throttle and apply more power as you start up the hill. Do not race forward into a steep grade; the abrupt change of grade could cause you to lose control. If the front end begins to bounce, ease off the throttle slightly to bring...

  • Page 367

    And hill descent braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock. Warning! Do not descend a steep grade in neutral. Use vehicle brakes in conjunction with engine braking. Descending a grade too fast could cause you to lose control and be seriousl...

  • Page 368

    Warning! (continued) tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in reverse gear. Never back down a hill in neutral using only the vehicle brakes. Never drive diagonally across a hill, always drive straight up or down. Driving throug...

  • Page 369

    Before you cross any type of water as you approach any type of water, you need to deter- mine if you can cross it safely and responsibly. If neces- sary, get out and walk through the water or probe it with a stick. You need to be sure of its depth, approach angle, current and bottom condition. Be ca...

  • Page 370

    Always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiato...

  • Page 371

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 372

    Caution! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the new vehicle limited warranty. Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from movi...

  • Page 373

    When the parking brake is applied with the ignition switch in the on position, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is de...

  • Page 374

    Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be...

  • Page 375

    Brake system your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. How- ever, the effort required to brake the vehicle will be much gr...

  • Page 376

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system (ebc). This system includes elec- tronic brake force distribution (ebd), anti-lock brake system (abs), brake assist system (bas), hill start assist (hsa), traction control system (tcs), electron...

  • Page 377

    Braking conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking. The abs performs a self-check cycle to ensure that the abs is working properly each time the vehicle is started and driven. During this self-check, you may hear a slight clicking sound as w...

  • Page 378

    Warning! (continued) • the abs cannot prevent the natural laws of phys- ics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent collisions, including th...

  • Page 379

    Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 380

    Does not apply the throttle before this time expires, the system will release brake pressure and the vehicle will roll down the hill as normal. The following conditions must be met in order for hsa to activate: • the feature must be enabled. • the vehicle must be stopped. • park brake must be off. •...

  • Page 381

    Towing with hsa hsa will also provide assistance to mitigate roll back while towing a trailer. Warning! • if you use a trailer brake controller with your trailer, the trailer brakes may be activated and deactivated with the brake switch. If so, there may not be enough brake pressure to hold both the...

  • Page 382

    • if disabling hsa using uconnect settings, refer to “uconnect settings” in “understanding your instru- ment panel” for further information. For vehicles not equipped with the evic, perform the following steps: 1. Center the steering wheel (front wheels pointing straight forward). 2. Shift the trans...

  • Page 383

    Other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. Bld may remain enabled even if tcs and esc are in a reduced mode. Electronic stability control (esc) this system enhances directional control and stabilit...

  • Page 384

    Warning! (continued) • the capabilities of an esc-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others • vehicle modifications, or failure to properly main- tain your vehicle, may change the handling charac- teri...

  • Page 385

    Indicator light ⬙ will be illuminated. All other stability features of esc function normally. This mode is intended to be used if the vehicle is in deep snow, sand or gravel conditions, and more wheel spin than esc would nor- mally allow is required to gain traction. To turn esc on again, momentaril...

  • Page 386

    Light ⬙ will illuminate and the “esc off” message will appear in the odometer. Push and release the trip odom- eter button located on the instrument cluster to clear this message. In this mode, esc and tcs, except for the “limited slip” feature described in the tcs section, are turned off until the ...

  • Page 387

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is cycled to the on/ run position. It should go out with the engine running. If the “esc activation/malfunction indi...

  • Page 388

    When esc becomes inactive following the maneuver that caused the esc activation. The “esc off indicator light” indicates the electronic stability control (esc) is partially off or full off. Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver...

  • Page 389

    Hill descent control (hdc) — if equipped this system maintains vehicle speed while descending hills during off-road driving situations. Hdc will auto- matically apply the brakes to control downhill speed to between 4 mph (7 km/h) and 6 mph (9 km/h) depending on terrain. The system is activated by pl...

  • Page 390

    Warning! Hdc is only intended to assist the driver in control- ling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed. Tire safety information tire markings 1 — u.S. Dot safety standards code (tin) ...

  • Page 391

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 392

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ ....Blank.... ⴖ = passenger car tire based on european design standards, or lt = light truck tire based...

  • Page 393

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 394

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 395

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 396

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 397

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 5 starting and ...

  • Page 398

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 399

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in the “starting and operating” sec- tion of this manual. To determin...

  • Page 400

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (294 kg) (since 5 x 150 ...

  • Page 401

    5 starting and operating 399.

  • Page 402

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 403

    Warning! (continued) • unequal tire pressures can cause steering prob- lems. You could lose control of your vehicle. • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended col...

  • Page 404

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 405

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits ...

  • Page 406

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 407

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 408

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Run flat tires — if equipped run flat tires a...

  • Page 409

    Equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spa...

  • Page 410

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 411

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 412

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (1.6 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information....

  • Page 413

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance w...

  • Page 414

    Warning! (continued) braking of your vehicle. This can cause unpredict- able handling and stress to steering and suspen- sion components. You could lose control and have a collision resulting in serious injury or death. Use only the tire and wheel sizes with load ratings approved for your vehicle. •...

  • Page 415

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation a...

  • Page 416

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (7.0 kpa) for every 12°f (6.5°c). This means that when the ...

  • Page 417

    Note: when filling warm tires, the tire pressure may need to be increased up to an additional 4 psi (30 kpa) above the recommended cold placard pressure in order to turn the tire pressure monitoring telltale light off. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) in ...

  • Page 418

    Caution! (continued) • using aftermarket tire sealants may cause the tire pressure monitoring system (tpms) sensor to be- come inoperable. After using an aftermarket tire sealant it is recommended that you take your vehicle to an authorized dealership to have your sensor function checked. • after in...

  • Page 419

    Base system this is the tpms warning indicator located in the instrument cluster. The tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure lev- els. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver m...

  • Page 420

    Check tpms warnings the tire pressure monitoring telltale light will flash on and off for 75 seconds and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The ti...

  • Page 421

    4. For each subsequent ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare tire, the tp...

  • Page 422

    • various tire pressure monitoring system messages, which display in the electronic vehicle information center (evic) • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster and a...

  • Page 423

    The graphic display of the pressure value(s) will stop flashing, and the tire pressure monitoring light will extinguish once the updated tire pressure(s) have been received. Note: when filling warm tires, the tire pressure may need to be increased up to an additional 4 psi (30 kpa) above the recomme...

  • Page 424

    Text message will not be present, and a pressure value will be displayed instead of dashes. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing some form...

  • Page 425

    3. However, after driving the vehicle for up to 10 min- utes above 15 mph (24 km/h), the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system” mes- sage for a minimum of five seconds and then d...

  • Page 426

    Fuel requirements 2.0l and 2.4l engine these engines are designed to meet all emissions regulations and provide opti- mum fuel economy and performance when using high quality unleaded “regu- lar” gasoline having a posted octane num- ber of 87 as specified by the (r+m)/2 method. The use of higher oct...

  • Page 427

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Caution! Do not use gasoline containing methanol or gaso- line containing more than 15% ethanol (e-15). Use of these blends may result in starting and drivability problems, damage critical fuel s...

  • Page 428

    Mmt in gasoline methylcyclopentadienyl manganese tricarbonyl (mmt) is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended wi...

  • Page 429

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine per- formance and damage the emissions control sys- tem. • an out-of-tune engine or certain fuel or ignitio...

  • Page 430

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 431

    After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. Caution! • damage to the fuel system or emission control system could result from using an improper fuel tank filler c...

  • Page 432

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas...

  • Page 433

    Vehicle loading as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or b-pillar. Vehicle certification label your vehicle has a vehicle certification label attached to the driver’s door b-pillar. The la...

  • Page 434

    Inflation pressure this is the cold tire inflation pressure for your vehicle for all loading conditions up to full gawr. Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants ...

  • Page 435

    Caution! Do not load your vehicle any heavier than the gvwr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. Trailer towing in this section you will find safety ti...

  • Page 436

    The recommended way to measure gtw is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross combination weight rating (gcwr) the gcwr is the total permissible weight of your vehicle and trailer when weighed in combination. Gross a...

  • Page 437

    Trailer sway control the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-carryi...

  • Page 438

    Warning! (continued) • weight distributing systems may not be compat- ible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable rec- reational vehicle dealer for additional information. Trailer hitch classification the following chart provides the industry stand...

  • Page 439

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.0l auto/man 22 sq ft (2.04 sq m) 1,000 lbs (450 ...

  • Page 440

    Trailer and tongue weight never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your...

  • Page 441

    Towing requirements to promote proper break-in of your vehicle drivetrain components, the following guidelines are recommended: caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, during the f...

  • Page 442

    Warning! (continued) • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parke...

  • Page 443

    • check for signs of tire wear or visible tire damage before towing a trailer. Refer to “tires – general information” in “starting and operating” for the proper inspection procedure. • when replacing tires, refer to “tires – general infor- mation” in “starting and operating” for the proper tire repl...

  • Page 444

    Caution! If the trailer weighs more than 1,000 lbs (453 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing requirements — trailer lights an...

  • Page 445

    Four-pin connector 1 — female pins 2 — male pin 3 — ground 4 — park 5 — left stop/turn 6 — right stop/turn seven-pin connector 1 — battery 2 — backup lamps 3 — right stop/turn 4 — electric brakes 5 — ground 6 — left stop/turn 7 — running lamps 5 starting and operating 443.

  • Page 446

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Manual transmission — if equipped if using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippag...

  • Page 447

    Autostick — if equipped when using the autostick shift control, select the highest gear that allows for adequate performance and avoids frequent downshifts. For example, choose ⬙ 4 ⬙ if the desired speed can be maintained. Choose ⬙ 3 ⬙ or ⬙ 2 ⬙ if needed to maintain the desired speed. To prevent exc...

  • Page 448

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neu- tral • key in acc position not allowed dolly tow front fwd models only fwd models only rear n...

  • Page 449

    Caution! • do not flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are off the ground. • do not dolly tow any 4wd vehicle. Internal damage to the transmission or transfer case will occur i...

  • Page 451: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .451 䡵 if your engine overheats . . . . . . . . . . . .451 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .452 ▫ torque specifications . . . . . . . . . . . . . . . . . .453 䡵 jacking a...

  • Page 452

    䡵 gear selector override . . . . . . . . . . . . .482 䡵 towing a disabled vehicle . . . . . . . . . . .483 ▫ with ignition key . . . . . . . . . . . . . . . . . . . . .485 450 what to do in emergencies.

  • Page 453

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel, below the radio. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the ...

  • Page 454

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 455

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 100 ft-lbs (135 n·m) m12 x 1.5 19 mm **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the t...

  • Page 456

    After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may ...

  • Page 457

    Warning! (continued) under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • never start or run the engine while the vehicle is on a jack. • the jack is designed to be used as a tool for changing tires only. The ja...

  • Page 458

    Spare tire stowage the compact spare tire is stowed under the rear load floor in the cargo area. Spare tire removal lift up the load floor cover and remove the hold down. Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to ...

  • Page 459

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 460

    Note: refer to “tires — general information” in “start- ing and operating” for further information about the spare tire, it’s use, and operation. 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench and remove the wr...

  • Page 461

    2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. Note: there are front and rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts on one of the flanges in the sill flange ass...

  • Page 462

    Front jacking location rear jacking location 460 what to do in emergencies.

  • Page 463

    Do not raise the vehicle until you are sure the jack is securely engaged. 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 464

    Caution! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. Warning! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. Note: the wheel cover is held on th...

  • Page 465

    Correctly, have them checked with a torque wrench by your authorized dealer or service station. 8. Remove the wheel blocks and lower the jack until it is free. Release the parking brake. Reassemble the lug wrench to the jack assembly and stow it in the spare tire area. Secure the assembly using the ...

  • Page 466

    3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in se...

  • Page 467

    6. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel. Vehicles without wheel covers 1. Mount the road tire on the axle. 2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly...

  • Page 468

    Tire service kit — if equipped small punctures up to 1/4 inch (6 mm) in the tire tread can be sealed with tire service kit. Foreign objects (e.G., screws or nails) should not be removed from the tire. Tire service kit can be used in outside temperatures down to approximately -4°f (-20°c). This kit w...

  • Page 469

    Using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black air pump hose (7) when selecting this mode. ...

  • Page 470

    • the sealant bottle (1) and sealant hose (6) are a one tire application use and need to be replaced after each use. Always replace these components immediately at your original equipment vehicle dealer. • when the tire service kit sealant is in a liquid form, clean water, and a damp cloth will remo...

  • Page 471

    Warning! • do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the tire service kit. • do not use tire service kit or drive the vehicle under the following circumstances: – if the puncture in the tire t...

  • Page 472

    Warning! (continued) • tire service kit sealant solution contains latex. In case of an allergic reaction or rash, consult a phy- sician immediately. Keep tire service kit out of reach of children. If swallowed, rinse mouth imme- diately with plenty of water and drink plenty of water. Do not induce v...

  • Page 473

    4. Remove the cap from the valve stem and then screw the fitting at the end of the sealant hose (6) onto the valve stem. 5. Uncoil the power plug (8) and insert the plug into the vehicle’s 12 volt power outlet. Note: do not remove foreign objects (e.G., screws or nails) from the tire. (c) injecting ...

  • Page 474

    2. Connect the power plug (8) to a different 12 volt power outlet in your vehicle or another vehicle, if available. Make sure the engine is running before turning on the tire service kit. 3. The sealant bottle (1) may be empty due to previous use. Call for assistance. Note: if the mode select knob (...

  • Page 475

    If the tire inflates to the recommended pressure or is at least 26 psi (1.8 bar) pressure within 15 minutes: 1. Push the power button (4) to turn off the tire service kit. 2. Remove the speed limit sticker from the top of the sealant bottle (1) and place the sticker on the instru- ment panel. 3. Imm...

  • Page 476

    Warning! Tire service kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using tire service kit. Do not exceed 55 mph (90 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you,...

  • Page 477

    2. Disconnect the tire service kit from the valve stem, reinstall the cap on the valve stem and unplug from 12 volt outlet. 3. Place the tire service kit in its proper storage area in the vehicle. 4. Have the tire inspected and repaired or replaced at the earliest opportunity at an authorized dealer...

  • Page 478

    6. Verify that the cap is installed on the fitting at the end of the sealant hose (6) and return the hose to its storage area (located on the bottom of the air pump). 7. Return the tire service kit to its storage location in the vehicle. Jump-starting procedures if your vehicle has a discharged batt...

  • Page 479

    Preparations for jump-start the battery in your vehicle is located in the front of the engine compartment below the air intake duct. To access the battery remove the air intake duct by turning the two finger screws, located on the radiator support. Air intake finger screws positive battery post 6 wh...

  • Page 480

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 481

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Note: remove air intake before proceeding with this jump-starting procedure. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to...

  • Page 482

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the dis- charged battery. 2. Disconnect the opposite end of the negative (-) jumper cable...

  • Page 483

    And reverse (with automatic transmission) or 2nd gear and reverse (with manual transmission), while gently pressing the accelerator. Use the least amount of accel- erator pedal pressure that will maintain the rocking motion, without spinning the wheels, or racing the engine. Caution! Racing the engi...

  • Page 484

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 485

    4. Turn the ignition switch to the acc or on/run position, but do not start the engine. 5. Press and maintain firm pressure on the brake pedal. 6. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever forward. 7. Move the gear selector to the neutr...

  • Page 486

    Towing condition wheels off the ground manual transmission 6-speed automatic (fwd only) 6-speed auto- matic 4wd cvt automatic transmission flat tow none • transmission in neutral • key in acc or on/run position if transmission is operable: • transmission in neutral • 25 mph (40 km/h) max speed • 15 ...

  • Page 487

    With ignition key automatic transmission • front wheel drive (fwd) vehicles can be towed with the front wheels elevated, or on a flatbed truck (all four wheels off the ground). • four-wheel drive (4wd) vehicles can be towed on a flatbed truck (all four wheels off the ground). If the transmission is ...

  • Page 488

    Manual transmission • front wheel drive (fwd) or four-wheel drive (4wd) vehicles can be flat towed (all four wheels on the ground) with the transmission in neutral. • fwd vehicles can be towed with the front wheels elevated. • fwd or 4wd vehicles can be towed on a flatbed truck (all wheels off the g...

  • Page 489

    All transmissions if you must use the accessories (wipers, defroster, etc.) while being towed, the key must be in the on/run position, not the acc position. Make certain the trans- mission remains in neutral. Caution! • do not use sling-type equipment when towing. Vehicle damage may occur. • when se...

  • Page 491: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.0l . . . . . . . . . .491 䡵 engine compartment — 2.4l . . . . . . . . . .492 䡵 onboard diagnostic system — obd ii . .493 ▫ loose fuel filler cap message . . . . . . . . . . . .493 䡵 emissions inspection and maintenance programs . . . . . . ....

  • Page 492

    ▫ automatic transmission (six-speed) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .518 ▫ automatic transmission (cvt) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .520 ▫ manual transmission — if equipped . . . . . . .522 ▫ rear drive assembly (rda) — awd/4wd mod...

  • Page 493

    Engine compartment — 2.0l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 7 maintaining your vehicle 49...

  • Page 494

    Engine compartment — 2.4l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 492 maintaining your vehicle.

  • Page 495

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 496

    Persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil light off. Emissions inspection and maintenance programs in some localities, ...

  • Page 497

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 498

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 499

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, or air conditi...

  • Page 500

    At the low end of the indicated range will result in the oil level at the full end of the indicator range. Caution! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Al...

  • Page 501

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american petroleum institute (api). The manufacturer only recommends api certified engine oils. This symbol certifies 0w-20, 5w- 20, 0w-30, 5w-30 and 10w-30 en- gine oils. Cau...

  • Page 502

    Synthetic engine oils you may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Synthetic engine oils which do not have both the engine oil certification mark and the correct sae...

  • Page 503

    Engine air cleaner filter refer to the “maintenance schedule” in the “mainte- nance schedules” section for the proper maintenance intervals. Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air inductio...

  • Page 504

    Warning! (continued) splashes in eyes or on skin, flush the area imme- diately with large amounts of water. Refer to “jump-starting procedures” in “what to do in emergencies” for further information. • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a b...

  • Page 505

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 506

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized dealer or othe...

  • Page 507

    3. Pivot the glove compartment downward. 4. Disengage the two retaining tabs that secure the filter cover to the hvac housing, and remove the cover. 5. Remove the a/c air filter by pulling it straight out of the housing. 6. Install the a/c air filter with the arrow on the filter pointing toward the ...

  • Page 508

    Operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure pro...

  • Page 509

    When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperat...

  • Page 510

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 511

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 512

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot eng...

  • Page 513

    If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with oat coolant (antifreeze) (conforming to ms.90032). Refer to the “maintenance schedule” for the proper maintenance intervals. Selection of coolant refer to “fluids, lubricants, and...

  • Page 514

    Caution! (continued) • this vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (an- tifreeze) is not recommended. Adding coolant your vehicle has been built with an improved engine coolant (oat coolant conformin...

  • Page 515

    Note: • it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. • some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to ...

  • Page 516

    Warning! (continued) pressure cap while the system is hot or under pressure. • do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result. Disposal of used engine coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated...

  • Page 517

    Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when th...

  • Page 518

    Result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emis- sions. Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “maintenance schedule” for the proper maintenance interv...

  • Page 519

    Not indicate any leaks or other problems, it may be a result of a leak in the hydraulic clutch release system. See your local authorized dealer for service. Use only manufacturer’s recommended brake fluid. Re- fer to “fluids, lubricants, and genuine parts” in “main- taining your vehicle” for further...

  • Page 520

    Caution! Use of improper brake fluids will affect overall clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of clutch function and the ability to shift the transmis- sion. Automatic transmission (six-speed) — if equipped selection of lubricant (six-speed...

  • Page 521

    Leaks. Avoid using transmission sealers as they may adversely affect seals. Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is prese...

  • Page 522

    Fluid becomes contaminated (with water, etc.), or if the transmission is disassembled for any reason. Automatic transmission (cvt) — if equipped selection of lubricant (cvt) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufac...

  • Page 523

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 524

    Manual transmission — if equipped lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check check the fluid level by removing the fill plug. The fluid level ...

  • Page 525

    Frequency of fluid change refer to the “maintenance schedule” for the proper maintenance intervals. Power transfer unit (ptu) — awd/4wd models only lubricant selection use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for ...

  • Page 526

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 527

    Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • if you detect any stone chips or scratches...

  • Page 528

    Note: if your vehicle is equipped with dark vapor or black satin chrome wheels do not use wheel cleaners, abrasives or polishing compounds. They will perma- nently damage this finish and such damage is not cov- ered by the new vehicle limited warranty. Use only mild soap and water with a soft cloth....

  • Page 529

    Interior care use mopar total clean to clean fabric upholstery and carpeting. Use mopar total clean to clean vinyl upholstery. Mopar total clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particl...

  • Page 530

    Caution! Do not use alcohol and alcohol-based and/or keton based cleaning products to clean leather seats, as damage to the seat may result. Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratc...

  • Page 531

    Instrument panel bezels caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Cleaning plastic instrument cluster lenses the...

  • Page 532

    Warning! (continued) damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assem- blies must be replaced after a collision if they have been damaged (i.E., bent retractor, torn webbing, etc.). Fuses warning! • when replacing a blown fuse, always use an appro-...

  • Page 533

    Integrated power module (ipm) the integrated power module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed on the inside of the cover. Refer to “engine compartment” in “main-...

  • Page 534

    Cavity cartridge fuse mini-fuse description 4 – 10 amp red ignition switch/clock spring 5 – 15 amp lt blue battery feed for power tech 6 – 10 amp red power mirror/steering control sat- ellite radio/hands-free phone 7 – 30 amp green ignition off draw 8 – 30 amp green ignition off draw 9 40 amp green ...

  • Page 535

    Cavity cartridge fuse mini-fuse description 17 – 10 amp red wireless control module 18 40 amp green – auto shutdown relay 19 – 20 amp yellow radio amplifiers 20 – 15 amp lt blue radio 21 – 10 amp red intrusion module/siren – if equipped 22 – 10 amp red heating, ac/compass 23 – 15 amp lt blue auto sh...

  • Page 536

    Cavity cartridge fuse mini-fuse description 30 – 20 amp yellow heated seat – if equipped 31 – 10 amp red headlamp washer – if equipped 32 30 amp pink – auto shutdown relay 33 – 10 amp red j1962 conn/powertrain control module 34 30 amp pink – antilock brakevalve 35 40 amp green – antilock brake pump ...

  • Page 537

    Caution! • when installing the ipm cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the ipm, and possibly result in an electrical system failure. • when replacing a blown fuse, it is important to use only a fuse having ...

  • Page 538

    Interior bulbs bulb number front header lamp t578 center dome lamp t578 rear cargo lamp/flashlight 8–a35lf exterior bulbs bulb number low beam/high beam headlamp h13 front park/turn signal/side marker lamp 3757ka front fog lamp psx24w center high mounted stop lamp (chmsl) led assembly (serviced at a...

  • Page 539

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamps 1. Raise the hood and loc...

  • Page 540

    Rear tail, turn signal and backup lamps 1. Raise the liftgate. 2. Remove the two push-pins from the taillamp housing. 3. Grasp the taillamp and pull firmly to disengage the light from the aperture panel. 4. Twist and remove socket from the light. 5. Remove bulb from socket and replace. License lamps...

  • Page 541

    Fluid capacities u.S. Metric fuel (approximate) 13.6 gallons 51 liters engine oil with filter 2.0l and 2.4l engine (sae 5w-20, api certified) 4.5 quarts 4.26 liters cooling system * 2.0l and 2.4l engine (mopar antifreeze/engine coolant 10 year/150,000 mile formula or equivalent) 7.2 quarts 6.8 liter...

  • Page 542

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar antifreeze/coolant 10 year/ 150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of fca material standard ms.90032. Engine oil w...

  • Page 543

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 544

    Chassis component fluid, lubricant, or genuine part automatic transmission (cvt) — if equipped use only mopar cvtf+4 continuously variable transmission fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Automatic transmission (six-speed...

  • Page 545

    Component fluid, lubricant, or genuine part power transfer unit (ptu) we recommend you use mopar gear & axle lubricant sae 80w-90 api gl 5. Brake master cylinder we recommend you use mopar dot 3, sae j1703 should be used. If dot 3, sae j1703 brake fluid is not available, then dot 4 is acceptable. Po...

  • Page 547: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . .546 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .549 8.

  • Page 548

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 549

    Note: under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 hours of engine run time, whichever comes first. The 350 hours of engine run or idle time is generally only a concern for fleet customers. Severe duty all models change engine oil at 4,00...

  • Page 550

    Required maintenance intervals . Refer to the maintenance schedules on the following page for the required maintenance intervals. At every oil change interval as indicated by oil change indicator system: • change oil and filter. • rotate the tires. Rotate at the first sign of irregu- lar wear, even ...

  • Page 551

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 552

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 553

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 554

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 555: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .555 ▫ prepare for the appointment. . . . . . . . . . . . .555 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .555 ▫ be reasonable with requests ....

  • Page 556

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .561 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .561 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .562 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .562 554 if...

  • Page 557

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 558

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 559

    In mexico contact av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 puerto rico and u.S. Virgin islands customer service chrysler international services llc p.O. Box 191857 san juan 00919-1857 tel.: (787) 782-57...

  • Page 560

    Warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufacturer’s service contract, you will receive plan provisions and an owner identification card in the mail within three weeks of the vehicle delivery date. If you have any questions abo...

  • Page 561

    Warranty information see the warranty information booklet, located on the dvd, for the terms and provisions of fca us llc warranties applicable to this vehicle and market. Mopar parts mopar fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for...

  • Page 562

    Defect to the canadian government should contact trans- port canada, motor vehicle defect investigations and recalls at 1-800-333-0510 or go to http://www.Tc.Gc.Ca/ roadsafety/ publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. V...

  • Page 563

    Owner’s manuals these owner’s manuals have been prepared with the assistance of service and engineering specialists to ac- quaint you with specific fca us llc vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips. C...

  • Page 564

    Significantly from the norm due to variations in driving habits, service practices, and differences in road charac- teristics and climate. Traction grades the traction grades, from highest to lowest, are aa, a, b, and c. These grades represent the tire’s ability to stop on wet pavement, as measured ...

  • Page 565

    Warning! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure. 9 if you need consumer assistance 563.

  • Page 567: Index

    Index 10

  • Page 568

    Adding engine coolant (antifreeze) . . . . . . . . . . . .512 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .428 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .506 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .426 adjust down . . . . . . ....

  • Page 569

    Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . .539 disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .514 anti-lock brake system (abs) . . . . . . . . . . . . . . . .374 anti-lock warning light . . . . . . . . . . . . . . . . . . . .239 appearance care . . . . . ....

  • Page 570

    Bulbs, light . . . . . . . . . . . . . . . . . . . . . . . . . .103, 535 calibration, compass . . . . . . . . . . . . . . . . . . . . . .258 camera, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . .182 capacities, antifreeze (engine coolant) . . . . . . . . . .539 capacities, fluid . . . ...

  • Page 571

    Installing child restraints using the vehicle seat belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 lower anchors and tethers for children . . . . . . .84 older children and child restraints . . . . . . . . . .80 seating positions . . . . . . . . . . . . . . . . . . . . . ....

  • Page 572

    Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204 customer assistance . . . . . . . . . . . . . . . . . . . . . . .555 data recorder, event . . . . . . . . . . . . . . . . . . . . . . .75 dealer service. . . . . . . . . . . . . . . . . . . . . . . . . . . .496 defroster, rear w...

  • Page 573

    Emergency, in case of jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .454 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .476 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .483 emission control system maintenance . . . . . . . . . .494 engine....

  • Page 574

    Fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . . .539 fluid leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 fluid level checks automatic transaxle . . . . . . . . . . . . . . . . . . . . .521 automatic transmission . . . . . . . . . . . . . . . . . .519 cooling s...

  • Page 575

    Gauges fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . .344, 351 gear select lever override . . . . . . . . . . . . . . . . . .482 general information . . . . . . . . . . . . . . . . . . . . . . .145 glass cleaning...

  • Page 576

    Instrument cluster . . . . . . . . . . . . . . . . . .229, 230, 243 instrument panel and controls . . . . . . . . . . . . . . .218 instrument panel cover . . . . . . . . . . . . . . . . . . . . .528 instrument panel lens cleaning . . . . . . . . . . . . . . .529 integrated power module (fuses) . . ....

  • Page 577

    Brake warning . . . . . . . . . . . . . . . . . . . . . . . . .226 bulb replacement . . . . . . . . . . . . . . . . . . . . . . .537 cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .205 center mounted stop . . . . . . . . . . . . . . . . . . . .538 daytime running . . . . . . . . ....

  • Page 578

    Lug nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .452 lumbar support . . . . . . . . . . . . . . . . . . . . . . . . . .157 maintenance free battery. . . . . . . . . . . . . . . . . . . .501 maintenance procedures . . . . . . . . . . . . . . . . . . . .496 maintenance schedule . ...

  • Page 579

    Oil change indicator, reset . . . . . . . . . . . . . . . . . .251 oil, engine . . . . . . . . . . . . . . . . . . . . . . .497, 539, 540 capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .539 change interval . . . . . . . . . . . . . . . . . . . . . . . .498 checking . . . . . . . . ...

  • Page 580

    Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .193 transfer unit . . . . . . . . . . . . . . . . . . . . . . . . . .523 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 power seats down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153 forward ...

  • Page 581

    Remote control door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 security alarm . . . . . . . . . . . . . . . . . . . . . . . . . .18 remote keyless entry (sedan) . . . . . . . . . . . . . . . . .20 remote starting system. . . . . . . . . . . . . . . . . . . . . .26 replacement bu...

  • Page 582

    Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .42, 101 adjustable shoulder belt . . . . . . . . . . . . . . . . . . .50 adjustable upper shoulder anchorage . . . . . . . . .50 child restraint . . . . . . . . . . . . . . . . . . . . . . . . . .77 extender . . . . . . . . . . . . . ...

  • Page 583

    Spare tire . . . . . . . . . . . . . . . . . . . . .406, 407, 408, 456 spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .540 speed control accel/decel . . . . . . . . . . . . . . . . . . . . . . . . . . .181 cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179 r...

  • Page 584

    Air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . .400 chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .412 changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .454 compact spare . . . . . . . . . . . . . . . . . . . . . . . . .407 general information ....

  • Page 585

    Minimum requirements . . . . . . . . . . . . . . . . . .439 tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .444 trailer and tongue weight . . . . . . . . . . . . . . . .438 wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .442 trailer towing guide. . . . . . ....

  • Page 586

    Uconnect (hands-free phone) . . . . . . . . . . . . . . . .114 understanding your instrument panel. . . . . . . . . . .218 uniform tire quality grades . . . . . . . . . . . . . . . . .561 universal consumer interface (uci) connector . . . .306 universal transmitter . . . . . . . . . . . . . . . . . ...

  • Page 587

    Windshield defroster . . . . . . . . . . . . . . . .101, 319, 325 windshield washers . . . . . . . . . . . . . . . . . . . .172, 174 windshield wiper blades . . . . . . . . . . . . . . . . . . . .506 windshield wipers . . . . . . . . . . . . . . . . . . . . . . . .172 wiper blade replacement . . . ....

  • Page 588

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 589

    First edition printed in u.S.A. Stick with the specialists ® 16mk74-126-aa ©2015 fca us llc. All rights reserved. Jeep is a registered trademark of fca us llc..