1. DL manuals
  2. Jeep
  3. Automobile
  4. Compass 2013
  5. Owner's Manual

Jeep Compass 2013 Owner's Manual

Other manuals for Compass 2013: User Manual, User Manual, Owner's Manual

Summary of Compass 2013

  • Page 1

    Compass chrysler group llc o w n e r ’ s m a n u a l 2013 c ompas s 13mk49-126-aa first edition printed in u.S.A. 2 0 1 3.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million a...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against oper- ating procedures that could result in a collision or bodily injury. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss important ...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder. . . . . . . . . . . . . . . . .14 䡵 sentr...

  • Page 12

    ▫ to lock the doors and liftgate . . . . . . . . . . . .22 ▫ sound horn with remote key lock . . . . . . . . .22 ▫ flash lights with remote key lock/unlock . . .23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . .24 ▫ programming additional transmitters. . . . . . . .25 ▫ general informati...

  • Page 13

    ▫ seat belts in passenger seating positions . . . . . .54 ▫ automatic locking retractor mode (alr) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .54 ▫ energy management feature . . . . . . . . . . . . . .56 ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . .56 ▫ supplemen...

  • Page 14

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 15

    Note: if you try to remove the key before you place the shift lever in park, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in park, rotate the key to the right slightly, then remove the key as described. If a malfunc- tion occurs, the...

  • Page 16

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 17

    Sentry key® the sentry key® immobilizer system prevents unau- thorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded el...

  • Page 18

    Caution! The sentry key® immobilizer system is not compat- ible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronics...

  • Page 19

    Customer key programming if you have two valid sentry keys®, you can program new sentry keys® to the system by performing the following procedure: 1. Cut the additional sentry key® transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the igniti...

  • Page 20

    Note: if a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of s...

  • Page 21

    3. The vehicle security light in the instrument cluster will flash rapidly for approximately 16 seconds. This shows that the vehicle security alarm is arming. During this period, if a door is opened, the ignition switch is turned to on/run, or the power door locks are unlocked in any manner, the veh...

  • Page 22

    Vehicle security alarm manual override the vehicle security alarm will not arm if you lock the doors using the manual door lock plunger. Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances up to approxima...

  • Page 23

    To unlock the doors and liftgate press and release the unlock button on the rke transmitter once to unlock the driver’s door, or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn...

  • Page 24

    Note: pressing the lock button on the rke transmit- ter while you are inside the vehicle will activate the vehicle security alarm. Opening a door with the vehicle security alarm activated will cause the alarm to sound. Press the unlock button to deactivate the vehicle security alarm. Illuminated app...

  • Page 25

    • for vehicles not equipped with the evic, perform the following steps: 1. Press the lock button on a programmed rke trans- mitter for at least 4 seconds, but no longer than 10 sec- onds. Then, press the panic button while still holding the lock button. 2. Release both buttons at the same time. 3. T...

  • Page 26

    • for vehicles not equipped with the evic, perform the following steps: 1. Press and hold the unlock button on a programmed rke transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the lock button while still holding the unlock button. 2. Release both buttons at th...

  • Page 27

    Programming additional transmitters refer to sentry key® “customer key programming.” if you do not have a programmed rke transmitter, contact your authorized dealer for details. General information this device complies with part 15 of fcc rules and with rs-210 of industry canada. Operation is subjec...

  • Page 28

    2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the rke transmitter case, snap the two halves together. Note: if the rke transmitter is equipped wit...

  • Page 29

    How to use remote start all of the following conditions must be met before the engine will remote start: • shift lever in park • doors closed • hood closed • hazard switch off • brake switch inactive (brake pedal not pressed) • ignition key removed from ignition switch • battery at an acceptable cha...

  • Page 30

    Remote start abort message on electronic vehicle information center (evic) — if equipped the following messages will display in the evic if the vehicle fails to remote start or exits remote start prema- turely: • remote start aborted — door ajar • remote start aborted — hood ajar • remote start abor...

  • Page 31

    • the engine can be started two consecutive times (two 15-minute cycles) with the rke transmitter. However, the ignition switch must be cycled to the on/run position before you can repeat the start sequence for a third cycle. Remote start will also cancel if any of the following occur: • the engine ...

  • Page 32

    Door locks manual door locks use the manual door lock knob to lock the doors from inside the vehicle. If the lock knob is down when the door is closed, the door will lock. Make sure the keys are not inside the vehicle before closing the door. Warning! • for personal security and safety in the event ...

  • Page 33

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, a child could operate power windows, other controls, or move the vehicle. Caution! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of...

  • Page 34

    Auto lock doors — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). Auto lock doors programming the automatic door locks feature can be enabled or disabled as follows: • for veh...

  • Page 35

    Automatic unlock doors on exit the doors will unlock automatically if: • the automatic unlock doors on exit feature is enabled. • the transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). • the transmission is in neutral or park. • the driver’s door is opened. • the doors were n...

  • Page 36

    Note: • if you do not hear the chime it means that the system did not enter the programming mode and you will need to repeat the procedure. • use the automatic unlock doors on exit feature in accordance with local laws. Child-protection door lock system — rear doors to provide a safer environment fo...

  • Page 37

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: for emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window and open the doo...

  • Page 38

    Power windows — if equipped power window switches the window controls on the driver’s door trim panel control all the door windows. There are single window controls on each passenger door trim panel, which oper- ate the passenger door windows. The window controls will operate when the ignition switc...

  • Page 39

    Auto-down the driver’s door window switch has an auto-down feature. Push the window switch past the first detent, release, and the window will go down automatically. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Window lockout switch ...

  • Page 40

    Liftgate note: the key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn it to the right (manual lock models only). The liftgate can also be unlocked using the remote keyless entry (rke) tra...

  • Page 41

    Note: • in the event of a power malfunction, or the rke transmitter is inoperative, insert the key into the liftgate lock cylinder and turn to the right (manual lock models only). Using the liftgate handle, pull the lift- gate open with one fluid motion. • although the liftgate has no inside release...

  • Page 42

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for the driver and all passengers • advanced front air bags for driver and front passenger • supplemental active head restraints (ahr) located on top of the ...

  • Page 43

    If you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for children (latch) feature also can be used to hold infant and child restraint systems. For more information on latch, see lower anchors and tether for children (latch). Note: the ...

  • Page 44

    If a child from 1 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (refer to “child restraints”) you should read the instructions provided with your child restraint to make sure that you...

  • Page 45

    Warning! (continued) • supplemental side air bag inflatable curtain (sabic) and seat-mounted side air bags (sab) also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • in a collision, you and your passengers can suffer much greater injuries if you...

  • Page 46

    Lap/shoulder belts all seating positions in your vehicle are equipped with lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. However, in a colli...

  • Page 47

    Warning! (continued) • two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or lap belt for more than one person, no matter what their size. Lap/shoulder belt operating in...

  • Page 48

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into t...

  • Page 49

    Warning! (continued) • a shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thigh...

  • Page 50

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt may not protect you properly. In a collisi...

  • Page 51

    Adjustable upper shoulder belt anchorage in the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the anchorage button to release the anchorage, and move it up or down to the position that fits you best. Note: the adjustable upper shoulde...

  • Page 52

    Second row center lap/shoulder belt operating instructions the second row center lap/shoulder belt features a three-point seat belt with a mini-latch and buckle, which allows the shoulder belt to detach from the lower anchor when the seat is folded. The mini-buckle and shoulder belt can then be stor...

  • Page 53

    3. Route the shoulder belt to the inside of the right head restraint. 4. When the belt is long enough to fit, insert the mini- latch plate into the mini-buckle until you hear a “click.” 5. Sit back in the seat. Slide the regular latch plate up the webbing as far as necessary to allow the belt to go ...

  • Page 54

    7. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 8. Position the shoulder bel...

  • Page 55

    10. To disengage the mini-latch from the mini-buckle for storage, insert the regular latch plate into the black button on the top of the mini-buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. I...

  • Page 56

    Seat belts in passenger seating positions the seat belts in the passenger seating positions are equipped with automatic locking retractors (alr) which are used to secure a child restraint system. For additional information, refer to “installing child re- straints using the vehicle seat belt” under t...

  • Page 57

    Lap/shoulder belt. Use the automatic locking mode any- time a child safety seat is installed in a seating position that has a belt with this feature. Children 12 years old and under should always be properly restrained in the rear seat. How to engage the automatic locking mode 1. Buckle the combinat...

  • Page 58

    Energy management feature this vehicle has a safety belt system with an energy management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on collision. This safety belt system has a retractor assembly that is designed to release webbing in a co...

  • Page 59

    How the active head restraints (ahr) work the occupant restraint controller (orc) determines whether the severity, or type of rear impact will require the active head restraints (ahr) to deploy. If a rear impact requires deployment, both the driver and front passenger seat ahrs will be deployed. Whe...

  • Page 60

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: for more information on properly adjusting and positi...

  • Page 61

    3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 4. The ahr front soft foam and trim half should lock into the back decorative plastic half. 1 — downward movement 2 — rearward movement 3 — final downward movement to engage locking mechanism 2 thin...

  • Page 62

    Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an authorized dealer. Enhanced seat belt use reminder system (beltalert®) beltalert® is a feature in...

  • Page 63

    Unbuckled while traveling at speeds greater than 5 mph (8 km/h), beltalert® will provide both audio and visual notification. The front passenger seat beltalert® is not active when the front passenger seat is unoccupied. Beltalert® may be triggered when an animal or heavy object is on the front passe...

  • Page 64

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt lo...

  • Page 65

    The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation that are based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation ...

  • Page 66

    Air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolster • driver advanced front air bag • passenger advanced front air bag •...

  • Page 67

    Warning! • no objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • do not put anything on or around the air bag covers or attempt to open them manually. Y...

  • Page 68

    When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental side air bag inflatable curtain (sabic) sabic air...

  • Page 69

    • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the supplemental side air bag inflatable curtain and/or seat-mounted side air bag during deployment could cause you to be severely injured or killed. The system includes side ...

  • Page 70

    Children, should not lean on or sleep against the door, side windows, or area where the sab or sabic air bags inflate, even if they are in an infant or child restraint. Always sit upright as possible with your back against the seat back, use the seat belts properly, and use the appro- priate sized c...

  • Page 71

    The advanced front air bags will not deploy in all frontal collisions, including some that may produce sub- stantial vehicle damage — for example, some pole colli- sions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, advanced front ai...

  • Page 72

    It also includes diagnostics that will illuminate the instru- ment cluster air bag warning light if a malfunction is noted that could affect the air bag system. The diagnos- tics also record the nature of the malfunction. Warning! Ignoring the air bag warning light in your instru- ment panel could m...

  • Page 73

    Supplemental seat-mounted side air bag (sab) inflator units the supplemental seat-mounted side air bags (sab) are designed to activate only in certain side collisions. The orc determines if a side collision requires the side air bags to inflate, based on the severity and type of collision. Based on ...

  • Page 74

    Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an air bag should have deployed. Note: in a rollover the pretensioners and/or sab and sabic air bags may deploy on both sides of the vehicle. Front and side impact sensors in f...

  • Page 75

    If you do have a collision, which deploys the air bags, any or all of the following may occur: • the nylon air bag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the air bags deploy and unfold. The abrasions are similar to friction rope burns or tho...

  • Page 76

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 77

    Air bag warning light you will want to have the air bags ready to inflate for your protection in a collision. The air bag warning light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenan...

  • Page 78

    Vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The edr in this vehicle is designed to record such data as: • how various systems in your vehicle were operating; • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if ...

  • Page 79

    Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. There are different sizes and types of restraints for children from newborn size to the ch...

  • Page 80

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 81

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 82

    Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direc- tion are for children who are over two ye...

  • Page 83

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 84

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 85

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 86

    Latch positions for installing child restraints in this vehicle lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol 84 things to know before starting your vehicle.

  • Page 87

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 88

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to install a child seat in the center position next to a child sea...

  • Page 89

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between ...

  • Page 90

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing infant restraint...

  • Page 91

    To install a latch-compatible child restraint 1. If the selected seating position has a switchable auto- matic locking retractor (alr) seat belt, stow the seat belt, following the instructions below. See the section “installing child restraints using the vehicle seat belt” to check what type of seat...

  • Page 92

    How to stow an unused alr seatbelt when using the latch attaching system to install a child restraint, stow all alr seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the seatb...

  • Page 93

    Not necessary to use a locking clip. The alr retractor can be “switched” into a locked mode by pulling all of the webbing out of the retractor and then letting the webbing retract back into the retractor. If it is locked, the alr will make a clicking noise while the webbing is pulled back into the r...

  • Page 94

    What is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint, ...

  • Page 95

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. 2. Pull enough of the seat belt webbing fro...

  • Page 96

    8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “lower anchors and tethers for children (latch) restraint system” for directions to attach a tether anchor. 9. Test t...

  • Page 97

    5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “lower anchors and tethers for children (latch) restraint system” for directions to attach a tether anchor. 6. Test t...

  • Page 98

    Installing child restraints using the top tether anchorage 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for t...

  • Page 99

    Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. If your vehicle is equipped with a split rear seat, make sure the tether st...

  • Page 100

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of diff...

  • Page 101

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can even- tually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confin...

  • Page 102

    Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat b...

  • Page 103

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 104

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 105: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 ▫ inside day/night mirror . . . . . . . . . . . . . . . .107 ▫ automatic dimming mirror — if equipped . . .108 ▫ outside mirror — driver side . . . . . . . . . . . .109 ▫ outside ...

  • Page 106

    ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . . .144 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . . .147 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 ▫ power seats — if equipped . . . . . . . . . . . . . .148 ▫ heated seats — if equipped . . . ....

  • Page 107

    䡵 windshield wipers and washers . . . . . .168 ▫ windshield wiper operation . . . . . . . . . . . . .170 ▫ intermittent wiper system . . . . . . . . . . . . . . .170 ▫ windshield washers . . . . . . . . . . . . . . . . . . .170 ▫ mist feature . . . . . . . . . . . . . . . . . . . . . . . . .171 䡵 ti...

  • Page 108

    ▫ closing sunroof — manual mode . . . . . . . . . .187 ▫ pinch protect feature . . . . . . . . . . . . . . . . . . .187 ▫ venting sunroof — express . . . . . . . . . . . . . .188 ▫ sunshade operation. . . . . . . . . . . . . . . . . . . .188 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . ....

  • Page 109

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 110

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 111

    Outside mirror — driver side adjust the flat outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the door glass. Outside mirror — passenger side adjust the convex outside mirror so you can just see the side of your vehi...

  • Page 112

    Power mirrors the power mirror control is located on the driver’s door trim panel. To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the c...

  • Page 113

    Sun visor sliding feature the sun visors may be extended out to provide more coverage of the side glass. Uconnect® phone — if equipped uconnect® phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect® phone allows you to dial a phone number with your mobile phone using s...

  • Page 114

    Uconnect® phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The uconnect® phone is driven through your bluetooth® “hands-free profile” mobile phone. Uconnect® feature...

  • Page 115

    Voice command button actual button location may vary with the ra- dio. The individual buttons are described in the “operation” section. The uconnect® phone can be used with any hands-free profile certified bluetooth® mobile phone. See the uconnect® website for supported phones. Refer to your mobile ...

  • Page 116

    • for each feature explanation in this section, only the compound form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the compound form voice command “phonebook new entry”, or you can brea...

  • Page 117

    The following are general phone to uconnect® phone pairing instructions: • press the button to begin. • after the “ready” prompt and the following beep, say “device pairing”. • when prompted, after the beep, say “pair a device” and follow the audible prompts. • you will be asked to say a four-digit ...

  • Page 118

    • the system will prompt you to say the number you want to call. • for example, you can say “234-567-8901”. • the uconnect® phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by saying a name • press the button to begin. • after the “read...

  • Page 119

    • when prompted, enter the number designation (e.G., “home”, “work”, “mobile”, or “other”). This will allow you to store multiple numbers for each phonebook entry, if desired. • when prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry...

  • Page 120

    • a maximum of 1000 entries per phone will be down- loaded and updated every time a phone is connected to the uconnect® phone. • depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previou...

  • Page 121

    After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. “phonebook edit entry” can be used to add another phone number to a name entry that already exists in the p...

  • Page 122

    Delete/erase “all” uconnect® phonebook entries • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook erase all”. • the uconnect® phone will ask you to verify that you wish to delete all the entries from the phonebook. • after confirmation, the phonebook entri...

  • Page 123

    Phone call features the following features can be accessed through the uconnect® phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be accessed through the uconnect® phone. Check with your mobile se...

  • Page 124

    Call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to “toggling between calls” in this section. To combine two calls, refer to “conference call” in this section. Place/retrieve a call from hold to put a call on hold, press the button until ...

  • Page 125

    Call termination to end a call in progress, momentarily press the but- ton. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This i...

  • Page 126

    Uconnect® phone features language selection to change the language that the uconnect® phone is using: • press the button to begin. • after the “ready” prompt and the following beep, say the name of the language you wish to switch to english, espanol, or francais. • continue to follow the system prom...

  • Page 127

    Note: • the emergency number dialed is based on the country where the vehicle is purchased (911 for the u.S. And canada and 060 for mexico). The number dialed may not be applicable with the available mobile service and area. • if supported, this number may be programmable on some systems. To do this...

  • Page 128

    Note: • the roadside assistance number dialed is based on the country where the vehicle is purchased (1-800-528-2069 for the u.S., 1-877-213-4525 for canada, 55-14-3454 for mexico city and 1-800-712-3040 for outside mexico city in mexico). Please refer to the “roadside assistance” coverage details o...

  • Page 129

    Followed by the word “send”. For example, if required to enter your pin followed with a pound, (3 7 4 6 #), you can press the button and say, “3 7 4 6 # send”. Saying a number, or sequence of numbers, followed by “send”, is also to be used for navigating through an automated customer service center ...

  • Page 130

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G., the uconnect® phone will not repeat a phone number before you dial it). • press the button to begin. • after the “ready” prompt and the following beep, say one of the followi...

  • Page 131

    Mute/un-mute (mute on/off) when you mute the uconnect® phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect® phone: • press the button. • following the beep, say “mute”. In order to un-mute...

  • Page 132

    • when prompted, say “list phones”. • the uconnect® phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “se- lect” or “delete”. Also, see the next two sections f...

  • Page 133

    Things you should know about your uconnect® phone uconnect® phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect® tutorial.” voice training for users experiencing difficulty with the system recogniz- ing their voice commands or numbers, the uconnect® pho...

  • Page 134

    Voice command • for best performance, adjust the rearview mirror to provide at least ½ in (1 cm) gap between the overhead console (if equipped) and the mirror. • always wait for the beep before speaking. • speak normally, without pausing, just as you would speak to a person sitting a few feet/meters...

  • Page 135

    • even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • in a convertible vehicle, system performance may be compromised with the convertible top down. Far end audio performance • audio quality is maximized under...

  • Page 136

    Read messages: if you receive a new text message while your phone is connected to uconnect® phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • press the button. • after the “ready” prompt and the following beep, say “sms read” o...

  • Page 137

    List of preset messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L o l 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See you in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18....

  • Page 138

    Turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming messages. • press the button. • after the “ready” prompt and the following beep, say “setup, sms incoming message announcement,” you will then be given a choice to ch...

  • Page 139

    3 understanding the features of your vehicle 137.

  • Page 140

    138 understanding the features of your vehicle.

  • Page 141

    3 understanding the features of your vehicle 139.

  • Page 142

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location voice commands primary alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais 140 understanding ...

  • Page 143

    Voice commands primary alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book voice commands primary alternate (s) previous record again redial return to main menu return or main menu select phone select...

  • Page 144

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 145

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. When you press the voice command button, you...

  • Page 146

    At any point, if the system does not recognize one of your commands, you will be prompted to repeat it. To hear the first available menu, press the voice com- mand button and say “help” or “main menu”. Commands the voice command system understands two types of commands. Universal commands are availa...

  • Page 147

    Radio am to switch to the am band, say “am” or “radio am”. In this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next station” (to select the next station) • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “m...

  • Page 148

    Disc mode to switch to the disc mode, say “disc”. In this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) memo mode to switch to the voice ...

  • Page 149

    • “change to setup” • “main menu setup” or • “switch to setup” in this mode, you may say the following commands: • “language english” • “language french” • “language spanish” • “tutorial” • “voice training” note: keep in mind that you have to press the voice command button first and wait for the bee...

  • Page 150

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 151

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 152

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the center instrument panel area. You can choose from high, low or off heat settings. Amber ind...

  • Page 153

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Man...

  • Page 154

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 155

    Manual lumbar — if equipped the lumbar adjustment handle is located on the outboard side of the driver’s seatback. Rotate the lever downward to increase the lumbar support or rotate the lever upward to decrease the lumbar support. Driver’s seatback recline to adjust the seatback, lift the lever loca...

  • Page 156

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Fold-flat front passenger seat to fold the front passenger seat, lift the recliner han...

  • Page 157

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be ...

  • Page 158

    Active head restraints — front seats active head restraints are passive, deployable compo- nents, and vehicles with this equipment cannot be readily identified by any markings, only through visual inspec- tion of the head restraint. The head restraint will be split in two halves, with the front half...

  • Page 159

    For comfort the active head restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Active head restr...

  • Page 160

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 161

    Folding rear seat to provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to fold the rear seatback flat. To raise the seatback, pull the strap forward and lift the seatback into its upright position. Rear seat release strap folded rear seat 3 understandi...

  • Page 162

    Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Reclining rear seat — if equipped for ...

  • Page 163

    To open and close the hood to open the hood, two latches must be released. 1. Pull the hood release lever located on the left kick panel. 2. Move the safety latch, located outside the vehicle under the front edge of the hood, toward the center and raise the hood. Hood release lever hood safety latch...

  • Page 164

    Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment to secure the hood in the open position. Place the hood prop at the location stamped into the inner hood surface. Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood ...

  • Page 165

    Lights multifunction lever the multifunction lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and the fog lights. The multifunction lever is located on the left side of the ste...

  • Page 166

    Headlights and parking lights turn the end of the multifunction lever to the first detent to turn on the parking lights. Turn the end of the lever to the second detent to turn on the headlights. Daytime running lights — if equipped the high beam lights will come on as daytime running lights (lower i...

  • Page 167

    Note: the fog lights will only operate with the head- lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn ...

  • Page 168

    Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. Lane change assist tap the lever up or down once, without ...

  • Page 169

    Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on. Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are o...

  • Page 170

    Map/reading lights these lights are mounted between the sun visors above the rear view mirror. Each light is turned on by pressing the button. Press the button a second time to turn the light off. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the se...

  • Page 171

    Caution! • turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • in cold weather, always turn off the wiper switch and allow the wipers to return to the “park” posi- tion be...

  • Page 172

    Windshield wiper operation rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper operation. Intermittent wiper system use the i...

  • Page 173

    If the lever is pulled while in the off position, the wipers will operate for two wipe cycles, then turn off. Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freez...

  • Page 174

    Tilt steering column this feature allows you to tilt the steering column upward or downward. The tilt steering column lever is located on the left side of the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering whee...

  • Page 175

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 176

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 177

    To deactivate a soft tap on the brake pedal, pushing the cancel button, or normal brake pressure while slowing the vehicle will deactivate electronic speed control without erasing the set speed memory. Pressing the on/off button or turning the ignition switch off erases the set speed memory. To resu...

  • Page 178

    Using electronic speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so...

  • Page 179

    Note: homelink® is disabled when the vehicle secu- rity alarm is active. Homelink® buttons/overhead consoles homelink® buttons/sunvisor/headliner 3 understanding the features of your vehicle 177.

  • Page 180

    Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the d...

  • Page 181

    1. Cycle the ignition to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light in view. 3. Simultaneously press and hold both the homelink® button you want to program and the hand...

  • Page 182

    5. At the garage door opener motor (in the garage), locate the “learn” or “training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener/device motor. Firmly press and release the “learn” or “train- ing” button. On some garage door openers/devices t...

  • Page 183

    Programming a non-rolling code for programming garage door openers manufactured before 1995. 1. Turn the ignition switch to the on/run position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light i...

  • Page 184

    Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink® button until the indicator light begins to flash after 20 seconds. Do not release the butto...

  • Page 185

    3. Continue to press and hold the homelink® button, while you press and release (“cycle”), your hand-held transmitter every two seconds until homelink® has successfully accepted the frequency signal. The indi- cator light will flash slowly and then rapidly when fully trained. 4. Watch for the homeli...

  • Page 186

    Using homelink® to operate, press and release the programmed homelink® button. Activation will now occur for the programmed device (i.E., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The hand-held transmitter of the device may also be used at any...

  • Page 187

    Warning! • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” fea...

  • Page 188

    Power sunroof — if equipped the power sunroof switch is located on the overhead console. Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly un- attended children, can become entrapped by the power sunroof while operating the power sunroof switch...

  • Page 189

    Opening sunroof — express press the switch rearward and release it within one-half second. The sunroof and sunshade will open automati- cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “express open”. During express open operation, any movement...

  • Page 190

    Note: if three consecutive sunroof close attempts re- sult in pinch protect reversals, the fourth close attempt will be a manual close movement with pinch protect disabled. Venting sunroof — express press and release the vent button within one half second and the sunroof will open to the vent positi...

  • Page 191

    Ignition off operation for vehicles not equipped with the electronic vehicle information center (evic) the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. For vehicles equipped with t...

  • Page 192

    Power is available when the ignition switch is in the on or acc position. Insert the cigar lighter or accessory plug into the outlet for use. To preserve the heating element, do not hold the lighter in the heating position. Note: to ensure proper operation a mopar® knob and element must be used. Cau...

  • Page 193

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 194

    Power inverter — if equipped a 115 volt (150 watt) ac power inverter is located on the front of the center console for added convenience. This outlet can power mobile phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such as playstation3 a...

  • Page 195

    Warning! To avoid serious injury or death: • do not use a three-prong adaptor. • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories tha...

  • Page 196

    Cupholders your vehicle is equipped with four cupholders. There are two illuminated cupholders located in the front. There are two cupholders located in the back for the rear passengers. Front cupholders rear cupholders 194 understanding the features of your vehicle.

  • Page 197

    Storage glove compartment and storage bin located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. To open the lower glove compartment, pull outward on the release handle. Storage bins 1 — upper storage bin 2 — lower glove compartment glove compar...

  • Page 198

    Door storage the interior door panels are equipped with lower storage areas. Front door storage rear door storage 196 understanding the features of your vehicle.

  • Page 199

    Console features the floor console contains both an upper and lower storage compartment. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. To open the lower storage compartment, lift upward on the lower handle to unlatch the lower ...

  • Page 200

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injur...

  • Page 201

    To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Cargo cover the cargo area trim panels include two notches for mounting the available tonneau cover that accommo- dates the reclining rear seat. To install the cargo cover, insert either end ...

  • Page 202

    Using the handle, pull the cover toward you and guide the rear cover posts into the guides located on both sides of the rear trim panel. Warning! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store...

  • Page 203

    Removable load floor the cargo area load floor is removable and can be washed with mild soap and water. Cargo tie-down loops there are four tie-downs (d-rings) installed in the cargo area for securing cargo. Removable load floor cargo area tie-downs 3 understanding the features of your vehicle 201.

  • Page 204

    Warning! • cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • the weight and position of cargo a...

  • Page 205

    Fold down speakers — if equipped when the liftgate is open, the speakers can swing down off the trim panel to face rearward, for tailgating and other activities. Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the center portion of the ...

  • Page 206

    Rotate the center portion of the lever upward to the first detent position for rear wiper operation. Note: the rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to op...

  • Page 207

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 208

    The optional crossbars must also be secured in one of the seven detent positions marked with an arrow on the siderails to prevent movement. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately eight turns, then move the crossbar to the desired posit...

  • Page 209

    Caution! (continued) • to avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lb (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. • long loads which extend over the windshield, such as wood panels or surfb...

  • Page 211: Contents

    Understanding your instrument panel contents 䡵 instrument panel features. . . . . . . . . . .212 䡵 instrument cluster . . . . . . . . . . . . . . . . .213 䡵 instrument cluster descriptions . . . . .214 䡵 mini-trip computer — if equipped . . . . .228 ▫ control buttons . . . . . . . . . . . . . . . . ...

  • Page 212

    䡵 uconnect® 230 — am/fm stereo radio and 6–disc cd/dvd changer (mp3/wma aux jack) . . . . . . . . . . . . . . . . .242 ▫ operating instructions - radio mode . . . . . . . .242 ▫ operation instructions - (disc mode for cd and mp3/wma audio play, dvd-video) . . . .251 ▫ list button (disc mode for mp3/...

  • Page 213

    䡵 ipod®/usb/mp3 control — if equipped . .288 ▫ connecting the ipod® or external usb device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 ▫ using this feature. . . . . . . . . . . . . . . . . . . . .290 ▫ controlling the ipod® or external usb device using radio buttons . . . . . . . . ...

  • Page 214

    Instrument panel features 1 — air outlet 5 — storage bin 9 — heated seat switch – if equipped 2 — demisters 6 — glove compartment 10 — hazard warning flasher 3 — instrument cluster 7 — climate controls 11 — esc off switch – if equipped 4 — radio 8 — power outlet 12 — heated seat switch – if equipped...

  • Page 215

    Instrument cluster 4 understanding your instrument panel 213.

  • Page 216

    Instrument cluster descriptions 1. Fuel gauge / fuel door reminder when the ignition switch is in the on/run position, the pointer will show the level of fuel remaining in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 2. Charging system light t...

  • Page 217

    4. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate ...

  • Page 218

    9. High beam indicator this indicator shows that the high beam head- lights are on. Push the multifunction lever for- ward to switch the headlights to high beam, and pull toward yourself (normal position) to return to low beam. 10. Anti-lock brake (abs) light this light monitors the anti-lock brake ...

  • Page 219

    13. Engine temperature warning light this light warns of an overheated engine condi- tion. As engine coolant temperatures rise and the gauge approaches h, this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge...

  • Page 220

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 221

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run position. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Transmission temperature warning light this light indicates that the tra...

  • Page 222

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 223

    20. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: you must apply the brakes before shifting from park. 21. Odometer/trip odometer reset button press this button to change the display...

  • Page 224

    Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped wi...

  • Page 225

    23. Odometer display / trip odometer display area this display indicates the total distance the vehicle has been driven. Note: u.S. Federal regulations require that upon trans- fer of vehicle ownership, the seller certify to the pur- chaser the correct mileage that the vehicle has been driven. If yo...

  • Page 226

    Gascap if the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gascap” message will display in the odometer display area. Tighten the fuel filler cap properly and press the trip odometer button to turn off the message. If the problem contin...

  • Page 227

    Dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the on/run position. To turn off the message temporarily, press and release the trip odometer button on the instrument cluster. To reset the oil change indicator ...

  • Page 228

    Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warnin...

  • Page 229

    Running, a malfunction has been detected in the esc system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and cor...

  • Page 230

    30. Hill descent indicator — if equipped the symbol illuminates (is armed) when the 4wd lock switch is activated and the trans- mission range indicator is in low or reverse position (off-road mode). Mini-trip computer — if equipped the mini-trip computer is located in the instrument cluster and feat...

  • Page 231

    Step button press the step button located on the steering wheel to scroll through sub menus (i.E., temperature, trip func- tions: odometer, trip a, trip b). Reset button to reset the display shown, turn the ignition switch to the on position, then press and hold the reset button located on the steer...

  • Page 232

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • units • vehicle information warning message displays • ...

  • Page 233

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: menu button press and release the menu button to scroll through the main menus (fuel economy, warn- ings, timer, units, system, personal settings) or to exit sub-menus. Compass button ...

  • Page 234

    When the appropriate conditions exist, the evic displays the following messages: • turn signal on (with a continuous warning chime after 1 mile (1.6 km) of distance travelled) • left front turn signal lamp out (with a single chime) • left rear turn signal lamp out (with a single chime) • right front...

  • Page 235

    • key in ignition • low tire • low tire pressure display for premium tpm system • service tpm system engine oil change indicator system — if equipped oil change required your vehicle is equipped with an engine oil change indicator system. The “oil change required” message will flash in the evic disp...

  • Page 236

    Evic functions • compass/temperature/audio • average fuel economy • distance to empty (dte) • units in • elapsed time • tire pressure monitor (tpm) • personal settings to reset the display pressing and holding the select button once will clear the function currently being displayed. Reset will only ...

  • Page 237

    Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. This is not resettable. Note: significan...

  • Page 238

    Display units of measure in to make your selection, press and release the select button until “english” or “metric” appears. Personal settings (customer-programmable features) this allows the driver to set and recall features when the transmission is in park (automatic transmission) or the vehicle i...

  • Page 239

    Auto lock doors when on is selected, all doors lock automatically when the speed of the vehicle reaches 15 mph (24 km/h). Press and hold the select button when in this display until “on” or “off” appears to make your selection. Auto unlock on exit when on is selected, all the vehicle’s doors will un...

  • Page 240

    Sound horn with lock when on is selected, a short horn sound will occur when the rke transmitter lock button is pressed. This feature may be selected with or without the flash lights with lock feature. Press and hold the select button when in this display until “on” or “off” appears to make your sel...

  • Page 241

    Hill start assist (hsa) — if equipped when on is selected, the hsa system is active. Refer to “electronic brake control system” in “starting and oper- ating” for system function and operating information. To make your selection, press and release the select button until “on” or “off” appears. Displa...

  • Page 242

    Manual compass calibration if the compass appears erratic and the “cal” indicator does not appear in the evic display, you must put the compass into the calibration mode manually as follows: 1. Start the engine. Leave the shift lever in park in order to enter the evic programming menus. 2. Press the...

  • Page 243

    1. Turn the ignition switch on. 2. Press and hold the compass button for approxi- mately two seconds. 3. Press the down button until “compass variance” message and the last variance zone number displays in the evic. 4. Press and release the select button until the proper variance zone is selected ac...

  • Page 244

    Uconnect® 230 — am/fm stereo radio and 6-disc cd/dvd changer (mp3/wma aux jack) operating instructions - radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Press the o...

  • Page 245

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 246

    Time button press the time button to alternate locations of the time and frequency display. Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, press the right side tun...

  • Page 247

    Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control...

  • Page 248

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or undefined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news n...

  • Page 249

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 250

    Note: • the available selections for each of the above entries varies depending upon the disc. • these selections can only be made while playing a dvd. • ves™ power - allows you to turn ves™ on and off (if equipped). • ves™ lock - locks out rear ves™ remote controls (if equipped). • ves™ ch1/ch2 - a...

  • Page 251

    Audio language — if equipped selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙ other. ⬙ enter the country code using the tune/scroll control knob to scrol...

  • Page 252

    Autoplay — if equipped when this is set to on and a dvd video is inserted, it will bypass the dvd menu screen and automatically play the movie. In some rare cases, the dvd player may not auto-play the main title. In such cases, use the menu button on the remote control to select desired title to pla...

  • Page 253

    Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory {12 am, 12 fm, and 12 satellite (if equipped) stations}. Disc button pressing the disc button will allow you to switch from am/fm modes to disc modes. Operation instructions - (disc mode for cd and mp3/wm...

  • Page 254

    Radio display will show ⬙ loading disc ⬙ when the disc is loading and “reading disc” when the radio is reading the disc. Caution! This cd player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. Eject button — ejecting compact disc(s) press the...

  • Page 255

    Time button (cd mode) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode) press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (re...

  • Page 256

    • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • level 2: 31 (including a separator ⬙ . ⬙ and a three- character extension) multisession disc formats are supported by the radio. Multisession discs may contain combinat...

  • Page 257

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specification sampling fre- quency (khz) bit rate (kbps) wma 44.1 and 48...

  • Page 258

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button (disc mode for mp3/wma play) pressing the list button will bring up a list of all folders on ...

  • Page 259

    Seek button (auxiliary mode) no function. Scan button (auxiliary mode) no function. Eject button (auxiliary mode) no function. Time button (auxiliary mode) press the time button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Rw/ff (auxi...

  • Page 260

    Dolby® manufactured under license from dolby® laboratories. Dolby® and the double-d symbol are trademarks of dolby® laboratories. Macrovision this product incorporates copyright protection technol- ogy that is protected by u.S. Patents and other intellec- tual property rights. Use of this copyright ...

  • Page 261

    Information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www.Siriuscanada.Ca for canadian residents. Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic seria...

  • Page 262

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 263

    Additional three seconds will make the radio display the song title all of the time (press and hold again to return to normal display). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) tu...

  • Page 264

    Set/rnd button — to set the pushbutton memory when you are receiving a station that you wish to commit to pushbutton memory, press the set/rnd button. The symbol set 1 will now show in the display window. Select the button (1–6) you wish to lock onto this station and press and release that button. I...

  • Page 265

    Uconnect® 130 operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electron...

  • Page 266

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 267

    Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control...

  • Page 268

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored i...

  • Page 269

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 270

    Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pressing and holding the seek ...

  • Page 271

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 272

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 273

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 274

    Uconnect® 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn of...

  • Page 275

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 276

    Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the mi...

  • Page 277

    Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control...

  • Page 278

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or undefined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news n...

  • Page 279

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 280

    You may add a second station to each pushbutton by repeating the above procedure with this exception: press the set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored i...

  • Page 281

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 282

    Seek button press the right seek button for the next selection on the cd. Press the left seek button to return to the beginning of the current selection, or return to the beginning of the previous selection if the cd is within the first second of the current selection. Pressing and holding the seek ...

  • Page 283

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 284

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 285

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 286

    Press and hold the info button again for three seconds to return to ⬙ elapsed time ⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or ipod® and utilize the vehicle’s audio syst...

  • Page 287

    Information, call the toll-free number 888-539-7474, or visit the sirius web site at www.Sirius.Com, or at www.Siriuscanada.Ca for canadian residents. Electronic serial number/sirius identification number (esn/sid) please have the following information available when calling: 1. The electronic seria...

  • Page 288

    Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehicle is parked in an underground parking structure or under a physical obstacle. • dense tree coverage may interrupt reception in the form of short audio mutes. • driving under wide bridges or alon...

  • Page 289

    Additional three seconds will make the radio display the song title all of the time (press and hold again to return to normal display). Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control (rotary) tu...

  • Page 290

    Set button – to set the pushbutton memory when you are receiving a channel that you wish to commit to pushbutton memory, press the set button. The symbol set 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a butt...

  • Page 291

    Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support the ipod® control features. Please visit apple’s website for software updates. Note: • if the radio has a usb port, refer to the appropriate uconnect® multimedia radio user’...

  • Page 292

    Note: if the audio device battery is completely dis- charged, it may not communicate with the ipod®/usb/ mp3 control system until a minimum charge is attained. Leaving the audio device connected to the ipod®/usb/ mp3 control system may charge it to the required level. Using this feature by using an ...

  • Page 293

    • turning it clockwise (forward) by one click, while playing a track, skips to the next track or press the vr button and say ⬙ next track ⬙ . • turning it counterclockwise (backward) by one click, will jump to the previous track in the list or press the vr button and say ⬙ previous track ⬙ • jump ba...

  • Page 294

    • press the scan button to use ipod®/usb/mp3 de- vice scan mode, which will play the first 10 seconds of each track in the current list and then forward to the next song. To stop scan mode and start playing the desired track, when it is playing the track, press the scan button again. During scan mod...

  • Page 295

    • during all list modes, the ipod® displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backward (counter- clockwise) to get to the track faster. • in list mode, the radio preset buttons are used as shortcuts to the following lists on the ipod® ...

  • Page 296

    Caution! • leaving the ipod® or external usb device (or any supported device) anywhere in the vehicle in ex- treme heat or cold can alter the operation or dam- age the device. Follow the device manufacturer’s guidelines. • placing items on the ipod® or external usb device, or connections to the ipod...

  • Page 297

    Selecting a different audio device 1. Press the phone button to begin. 2. After the ⬙ ready ⬙ prompt and following the beep, say ⬙ setup ⬙ , then say ⬙ select audio devices ⬙ . 3. Say the name of the audio device or ask the uconnect® phone system to list the audio devices. Next track use the seek up...

  • Page 298

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pr...

  • Page 299

    Radio operation pressing the top of the switch will “seek” up for the next listenable station and pressing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gram...

  • Page 300

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 301

    Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and inner push knobs. Blower control rotate this control to regulate the...

  • Page 302

    Temperature control rotate this control to regulate the tem- perature of the air inside the passenger compartment. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures. Note: if your air conditionin...

  • Page 303

    • bi-level air is directed through the panel and floor outlets. Note: for all settings, except full cold or full hot, there is a difference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets. This feature gives improved comfort during sunny but cool conditi...

  • Page 304

    • recirculation control pressing the recirculation control button will put the system in recirculation mode. This can be used when outside conditions such as smoke, odors, dust, or high humidity are pres- ent. Activating recirculation will cause the led in the control button to illuminate. Note: • c...

  • Page 305

    Note: the air conditioning compressor will not engage until the engine has been running for about 10 seconds. • max a/c for maximum cooling use the a/c and recirculation buttons at the same time. • economy mode if economy mode is desired, press the a/c button to turn off the indicator light and the ...

  • Page 306

    Automatic operation operation of the system is quite simple. 1. Turn the mode control knob (on the right) and the blower control knob (on the left) to auto. Note: the auto position performs best for front seat occupants only. 2. Dial in the temperature you would like the system to maintain by ro- ta...

  • Page 307

    • if your air conditioning performance seems lower than expected, check the front of the a/c condenser located in front of the radiator for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduc...

  • Page 308

    306 understanding your instrument panel.

  • Page 309

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center ...

  • Page 310

    • air conditioner control press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Press this but- ton a second time to turn off the air conditionin...

  • Page 311

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pressing the recirculation button. However, under certain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the re...

  • Page 312

    Winter operation use of the air recirculation mode during winter months is not recommended because it may cause window fogging. Vacation storage anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five mi...

  • Page 313

    Side window demisters a side window demister outlet is located at each end of the instrument panel. These non-adjustable outlets direct air toward the side windows when the system is in the floor, mix, or defrost mode. The air is directed at the area of the windows through which you view the outside...

  • Page 314

    Control setting suggestions for various weather conditions 312 understanding your instrument panel.

  • Page 315: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .317 ▫ manual transmission – if equipped . . . . . . . .317 ▫ automatic transmission – if equipped . . . . . .318 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .318 ▫ extreme cold weather (below –20°f ...

  • Page 316

    䡵 autostick® . . . . . . . . . . . . . . . . . . . . . . . . .330 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .331 䡵 four-wheel drive operation — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .332 䡵 on-road driving tips . . . . . . . . . . . . . . . .333 䡵 power ste...

  • Page 317

    䡵 tires — general information. . . . . . . . .362 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .362 ▫ tire inflation pressures . . . . . . . . . . . . . . . . .363 ▫ tire pressures for high speed operation . . . .365 ▫ radial ply tires . . . . . . . . . . . . . . . . . . . . . .365 ...

  • Page 318

    ▫ reformulated gasoline . . . . . . . . . . . . . . . . .385 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . .385 ▫ e-85 usage in non-flex fuel vehicles . . . . . . .386 ▫ mmt in gasoline . . . . . . . . . . . . . . . . . . . . .386 ▫ materials added to fuel . . . . . . . . . . . . . . . .387 ...

  • Page 319

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the ...

  • Page 320

    Automatic transmission – if equipped the shift lever must be in the park or neutral position before you can start the engine. Apply the brakes before shifting to any driving gear. Note: you must press the brake pedal before shifting out of park. Tip start do not press the accelerator. Turn the ignit...

  • Page 321

    Warning! (continued) another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. Refer to “jump starting” in “what to do in emer- gencies” for further information. Extreme cold weather (below –20°f or −29°c) to ensure reliable starting at these tempera...

  • Page 322

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 323

    Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in a gear higher than first gear. Caution! • launching in any gear except 1st gear will result in excess...

  • Page 324

    Never shift into reverse until the vehicle has come to a complete stop. Note: during cold weather, until the transmission lubri- cant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the transmission. Recommended shift speeds to use your manual transmissio...

  • Page 325

    Automatic transmission — if equipped caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine i...

  • Page 326

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the ignition key/fob in or ...

  • Page 327

    Out of park, the ignition switch must be turned to the on/run position (engine running or not) and the brake pedal must be pressed. Continuously variable automatic transmission (cvt) the shift lever position display (located in the instrument cluster) indicates the transmission gear range. You must ...

  • Page 328

    Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use...

  • Page 329

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to mo...

  • Page 330

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 331

    Reverse this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift ...

  • Page 332

    Control (refer to autostick® in this section) to select a lower gear ratio. Under these conditions, using a lower gear ratio will improve performance and extend trans- mission life by reducing excessive shifting and heat buildup. During sustained high speed driving or trailer towing up long grades o...

  • Page 333

    Operation note: autostick® is not available until the cvt warms up in cold weather. When the shift lever is in the drive position, autostick® is activated by moving the shift lever side-to-side. Mov- ing the shift lever to the right (+) will activate autostick® and shift up to the next higher manual...

  • Page 334

    • if the system detects powertrain overheating, the transmission will revert to the automatic shift mode and remain in that mode until the powertrain cools off. • if the system detects a problem, it will disable autostick® mode and the transmission will return to automatic mode until the problem is ...

  • Page 335

    Where one or more wheels have wheel spin or if addi- tional traction is needed in sand, deep snow, or loose traction surfaces, activate the “4wd lock” switch by pulling up once and releasing. This locks the center coupling allowing more torque to be sent to the rear wheels. The “4wd indicator light”...

  • Page 336

    Power steering the standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible t...

  • Page 337

    Power steering fluid check checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an aut...

  • Page 338

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave an automatic transmission in park, or manual transmission in reverse or first gear. The parking brake lever is located in the center console. To apply the parking brake, pull the le...

  • Page 339

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 340

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic trans- mission in park, a manual transmission in re- verse or first gear. Failure to do so may cause the vehicle to roll and cause...

  • Page 341

    If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfuncti...

  • Page 342

    Warning! (continued) • the abs cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • the capabilities of an abs-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize th...

  • Page 343

    Abs is activated during braking under certain road or stopping conditions. Abs-inducing conditions can in- clude ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops. You may also experience the following when the brake system goes into anti-lock mode: • the abs motor running (it ...

  • Page 344

    Electronic brake control system your vehicle may be equipped with an optional ad- vanced electronic brake control system that includes anti-lock brake system (abs), traction control system (tcs), brake assist system (bas), electronic roll mitiga- tion (erm), hill descent control (hdc), hill start as...

  • Page 345

    Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 346

    Electronic roll mitigation (erm) this system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When erm determines that the rate of change of the steering wheel angle and vehicles speed are sufficient to potentially cause wheel lif...

  • Page 347

    Hill descent control (hdc) – if equipped this system maintains vehicle speed while descending hills during off-road driving situations. Hdc will auto- matically apply the brakes to control downhill speed to between 4 mph (7 km/h) and 6 mph (9 km/h) depending on terrain. The system is activated by pl...

  • Page 348

    Hill start assist (hsa) – manual transmission only the hsa system is designed to assist the driver when starting a vehicle from a stop on a hill. Hsa will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If t...

  • Page 349

    For vehicles not equipped with the evic, perform the following steps: note: you must complete steps 1 through 8 within 90 seconds. 1. Center the steering wheel (front wheels pointing straight forward). 2. Shift the transmission into neutral. 3. Apply the parking brake. 4. Start the engine. 5. Releas...

  • Page 350

    Electronic stability control (esc) this system enhances directional control and stability of the vehicle under various driving conditions. Esc cor- rects for over-steering or under-steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over-steering or ...

  • Page 351

    Esc operating modes the esc system has three available operating modes for four–wheel drive equipped vehicles and two available operating modes for two–wheel drive equipped vehicles. Full on (four-wheel drive models) or on (two-wheel drive models) this is the normal operating mode for esc. Whenever ...

  • Page 352

    Warning! When in “partial off” mode, the tcs functionality of esc (except for the limited slip feature described in the tcs section) has been disabled and the “esc off indicator light” will be illuminated. When in “par- tial off” mode, the engine power reduction of tcs is disabled, and the enhanced ...

  • Page 353

    To turn esc on again, momentarily press the “esc off” switch. This will restore the “esc on” mode of operation. Note: the “esc off” message will display and an audible chime will sound when the shift lever is placed into the park position from any other position, and then moved out of the park posit...

  • Page 354

    Malfunction indicator light” begins to flash during ac- celeration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. Note: • the “esc activation/malfunction indicator light” and the “esc off indicator ligh...

  • Page 355

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 356

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ ....Blank.... ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 21...

  • Page 357

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 358

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 359

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 360

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire and loading information placard this placard tells you important information about the: ...

  • Page 361

    3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to th...

  • Page 362

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 363

    5 starting and operating 361.

  • Page 364

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 365

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear pat- terns...

  • Page 366

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire infl...

  • Page 367

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 368

    The tire sidewall. Use all season tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Summer or three season tires – if equipped summer tires provide traction in both wet and dry conditions, and are not intended to be driven in snow or on ice. S...

  • Page 369

    Spare tire matching original equipped tire and wheel – if equipped your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for y...

  • Page 370

    Since this tire has limited tread life the original equip- ment tire should be repaired (or replaced) and reinstalled on your vehicle at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically fo...

  • Page 371

    Tire affects vehicle handling. Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Warning! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects ...

  • Page 372

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 373

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 374

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 375

    Tire chains (traction devices) due to limited clearance, tire chains or traction devices are not recommended. Caution! Damage to the vehicle may result if tire chains are used. Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform differ...

  • Page 376

    The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure b...

  • Page 377

    Also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pressure. The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects, or natural pr...

  • Page 378

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, ty...

  • Page 379

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Base system this is the tpms warning indicator located in the instrument cluster. The tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pres...

  • Page 380

    Check tpms warnings the tire pressure monitoring telltale light will flash on and off for 75 seconds and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The ti...

  • Page 381

    3. However, after driving the vehicle for up to 20 minutes above 15 mph (24 km/h), the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. 4. For each subsequent ignition key cycle, a chime will sound and the tire pressure monitoring telltale light ...

  • Page 382

    Tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster and an audible chime will be activated when one or more of the four active road tire pressures are low. The audible chime will sound once every ignition cycle for th...

  • Page 383

    “low tire” text message will no longer be displayed, the graphic display of the pressure value(s) will stop flashing, and the tire pressure monitoring light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 k...

  • Page 384

    Text message will not be present, and a pressure value will be displayed instead of dashes. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing some form...

  • Page 385

    2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warn- ing limit, upon the next ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will still turn on due to the low tire. The “low tire” text message and th...

  • Page 386

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 387

    Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recom- mends the use of gasolines...

  • Page 388

    E-85 usage in non-flex fuel vehicles non-ffv vehicles are compatible with gasoline contain- ing 10% ethanol (e10). Gasoline with higher ethanol content may void the vehicle’s warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • ...

  • Page 389

    Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the f...

  • Page 390

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 391

    After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. Caution! • damage to the fuel system or emission control system could result from using an improper fuel tank filler c...

  • Page 392

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas...

  • Page 393

    Vehicle certification label your vehicle has a vehicle certification label attached to the driver’s door b-pillar. The label contains the following information: • name of manufacturer • month and year of manufacture • gross vehicle weight rating (gvwr) • vehicle identification number (vin) • type of...

  • Page 394

    Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a comm...

  • Page 395

    Trailer towing in this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow t...

  • Page 396

    Gross axle weight rating (gawr) the gawr is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear gawr. Refer to “vehicle loading/vehicle certifica- tion label” in “starting and operating” for...

  • Page 397

    Weight-carrying hitch a weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kinds of hitches are the most popular on the market today and they are commonly used to tow small- and medium-size...

  • Page 398

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 399

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.0l auto/man 22 sq ft (2.04 sq m) 1,000 lbs (450 ...

  • Page 400

    Which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions. Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of t...

  • Page 401

    Towing requirements to promote proper break-in of your vehicle drivetrain components, the following guidelines are recommended: caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, during the f...

  • Page 402

    Warning! (continued) • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parke...

  • Page 403

    Towing requirements – tires • do not attempt to tow a trailer while using a compact spare tire. • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation proce...

  • Page 404

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 405

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 406

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Manual transmission – if equipped if using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippag...

  • Page 407

    To prevent excess heat generation, avoid continuous driving at high rpm. Reduce vehicle speed as necessary to avoid extended driving at high rpm. Return to a higher gear or vehicle speed when grade and road conditions allow. Electronic speed control – if equipped • do not use in hilly terrain or wit...

  • Page 408

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neutral • key in acc position not allowed dolly tow front ok (fwd only) ok (fwd only) rear not all...

  • Page 409: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .408 䡵 if your engine overheats . . . . . . . . . . . .408 䡵 automatic transmission overheating . . . . . . . . . . . . . . . . . . . . . . .409 䡵 jacking and tire changing . . . . . . . . . .410 ▫ jack location . . . ....

  • Page 410

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency...

  • Page 411

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 412

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 413

    Jack location the jack and jack-handle are stowed under the load floor in the cargo area. Spare tire stowage the compact spare tire is stowed under the rear load floor in the cargo area. Spare tire removal lift up the load floor cover and remove the hold down. Preparations for jacking 1. Park the ve...

  • Page 414

    2. Turn on the hazard warning flasher. 3. Set the parking brake. 4. Place the shift lever in park (automatic transmission) or reverse (manual transmission). 5. Turn off the ignition. 6. Block both the front and rear of the wheel diagonally opposite the jack- ing position. For example, if chang- ing ...

  • Page 415

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 416

    Note: refer to “tires — general information” in “start- ing and operating” for further information about the spare tire, it’s use, and operation. 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench and remove the wr...

  • Page 417

    Note: there are front and rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts on one of the flanges in the sill flange assembly. The rear location is the same but with two rectangular cutouts. For vehicles equipped with plastic trim, the plasti...

  • Page 418

    Do not raise the vehicle until you are sure the jack is securely engaged. Front jacking location rear jacking location 416 what to do in emergencies.

  • Page 419

    3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. Warning! Raising the vehicle higher than necessary ...

  • Page 420

    Caution! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. Warning! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. Note: the wheel cover is held on th...

  • Page 421

    8. Remove the wheel blocks and lower the jack until it is free. Release the parking brake. Reassemble the lug wrench to the jack assembly and stow it in the spare tire area. Secure the assembly using the means provided. Warning! A loose tire or jack thrown forward in a collision or hard stop could e...

  • Page 422

    3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in pe...

  • Page 423

    About the correct tightness, have them checked with a torque wrench by your authorized dealer or service station. 6. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel. Vehicles without wheel covers 1. Mount the road...

  • Page 424

    Jump-starting procedures if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section caref...

  • Page 425

    Air intake finger screws positive battery post 6 what to do in emergencies 423.

  • Page 426

    Warning! • take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You coul...

  • Page 427

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Note: remove air intake before proceeding with this jump-starting procedure. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the...

  • Page 428

    Once the engine is started, remove the jumper cables in the reverse sequence: 6. Disconnect the negative (-) jumper cable from the engine ground of the vehicle with the discharged battery. 7. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. 8. Di...

  • Page 429

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse (with automatic transmission) or 2nd gear an...

  • Page 430

    Caution! • when “rocking” a stuck vehicle by shifting be- tween drive/2nd gear and reverse, do not spin the wheels faster than 15 mph (24 km/h), or drive- train damage may result. • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damag...

  • Page 431

    3. Using a small screwdriver or similar tool, remove the shift lever override access cover (located on the right side of the shifter housing). 4. Turn the ignition switch to the acc or on/run position, but do not start the engine. 5. Press and maintain firm pressure on the brake pedal. 6. Insert the...

  • Page 432

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. Towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neutral • key in acc or on/run position not allowed wheel li...

  • Page 433

    With ignition key automatic transmission • front wheel drive (fwd) vehicles can be towed with the front wheels elevated, or on a flatbed truck (all four wheels off the ground). • four-wheel drive (4wd) vehicles must be towed on a flatbed truck (all four wheels off the ground). Caution! • do not flat...

  • Page 434

    All transmissions if you must use the accessories (wipers, defroster, etc.) while being towed, the key must be in the on/run position, not the acc position. Make certain the trans- mission remains in neutral. If the vehicle’s battery is discharged, see “shift lever override” in this section for inst...

  • Page 435: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.0l . . . . . . . . . .435 䡵 engine compartment — 2.4l . . . . . . . . . .436 䡵 onboard diagnostic system — obd ii . . .437 ▫ loose fuel filler cap message . . . . . . . . . . . .437 䡵 emissions inspection and maintenance programs . . . . . ....

  • Page 436

    ▫ automatic transmission – if equipped . . . . . .462 ▫ manual transmission – if equipped . . . . . . . .463 ▫ rear drive assembly (rda) – awd/4wd models only . . . . . . . . . . . . . . .464 ▫ power transfer unit (ptu) – awd/4wd models only . . . . . . . . . . . . . . .465 ▫ appearance care and pro...

  • Page 437

    Engine compartment — 2.0l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 7 maintaining your vehicle 43...

  • Page 438

    Engine compartment — 2.4l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 436 maintaining your vehicle.

  • Page 439

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 440

    The gas cap is properly tightened. Press the trip odometer reset button to turn off the message. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resol...

  • Page 441

    4. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 442

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 443

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 444

    Caution! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Also, be sure the oil fill cap is replaced and tightened after adding oil. Change engine oil the oil change i...

  • Page 445

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity (sae grade) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperatu...

  • Page 446

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 447

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 448

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and are identified on the battery case. Cable clamps should b...

  • Page 449

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 450

    Warning! Do not remove the a/c air filter while the blower is operating or personal injury may result. The a/c air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1. Open the glove compartment and remove all contents. 2. Push in...

  • Page 451

    5. Remove the a/c air filter by pulling it straight out of the housing. 6. Install the a/c air filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. Caution! The a/c air filter is identified with an arrow...

  • Page 452

    Windshield wiper blades clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the w...

  • Page 453

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 454

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 455

    To minimize the possibility of catalytic converter damage: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires disc...

  • Page 456

    Coolant checks check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh engine coolant (anti- freeze). Chec...

  • Page 457

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybrid ...

  • Page 458

    Adding coolant your vehicle has been built with an improved engine coolant (oat coolant conforming to ms-12106) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to ten years or 150,000 miles (240,000 km) before replacement. To pre- vent reducing this extend...

  • Page 459

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign mat...

  • Page 460

    Coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling and warm to normal operating tempera- ture, the level of the engine coolant (antifreeze) in the bottle should be between the “add” and “full” lines shown on the ...

  • Page 461

    • if frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested for leaks. • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms-12106) and distilled water for proper corrosion protection of your engine w...

  • Page 462

    Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning light is on. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level u...

  • Page 463

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 464

    Automatic transmission – if equipped selection of lubricant (cvt) it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s recommended transmission fluid which has the special friction coefficient additives necessary for pr...

  • Page 465

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 466

    Fluid level check check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16 in (4.7 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency of fluid change under normal oper...

  • Page 467

    Power transfer unit (ptu) – awd/4wd models only lubricant selection use only the manufacturer’s recommended fluid. Refer to “fluids, lubricants, and genuine parts” in “maintain- ing your vehicle” for further information. Fluid level check visually inspect the unit at each oil change for leakage. If ...

  • Page 468

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 469

    Special care • if you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • it is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • if you detect any stone chips or scratches...

  • Page 470

    Caution! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s pro- tective finish. Only mopar® whee...

  • Page 471

    Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar® total clean. ...

  • Page 472

    Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar® glass cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window ...

  • Page 473

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol con...

  • Page 474

    Fuses integrated power module the integrated power module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed on the inside of the cover. Refer to “engine compartment” in “main-...

  • Page 475

    Cavity car- tridge fuse mini- fuse description 1 empty empty 2 15 amp lt blue awd/4wd control module – if equipped 3 10 amp red rear center brake light switch 4 10 amp red ignition switch/ occupant classifica- tion module 5 20 amp yellow trailer tow – if equipped cavity car- tridge fuse mini- fuse d...

  • Page 476

    Cavity car- tridge fuse mini- fuse description 11 15 amp lt blue power outlet 12 20 amp yellow 115v ac inverter – if equipped 13 20 amp yellow cigar lighter 14 10 amp red instrument cluster 15 40 amp green radiator fan 16 15 amp lt blue dome lamp/ sunroof/rear wiper motor cavity car- tridge fuse min...

  • Page 477

    Cavity car- tridge fuse mini- fuse description 23 15 amp lt blue auto shutdown relay 24 15 amp lt blue power sunroof – if equipped 25 10 amp red heated mirror – if equipped 26 15 amp lt blue auto shutdown relay 27 10 amp red airbag control module 28 10 amp red airbag control module/occupant classifi...

  • Page 478

    Cavity car- tridge fuse mini- fuse description 35 40 amp green antilock brake pump 36 30 amp pink headlamp/washer control/smart glass – if equipped 37 25 amp natural diesel fuel heater – if equipped caution! • when installing the ipm cover, it is important to ensure the cover is properly positioned ...

  • Page 479

    Vehicle storage if you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • disengage the mini-fuse in the power distribution center labeled iod (ignition off-draw). • or disconnect the negative cable from the battery. • anytime you store your ...

  • Page 480

    Exterior bulbs bulb number low beam headlamp h11 high beam headlamp 9005 front park/turn signal lamp 7444na front side marker lamp 194 front fog lamp h11 center high mounted stop lamp (chmsl) led assembly (serviced at authorized dealer) rear tail/stop lamp led assembly (serviced at authorized dealer...

  • Page 481

    Fog lamps 1. Access lamp through the lower fascia cutout. 2. Remove electrical connector from bulb. 3. Remove bulb from housing. Rear turn signal and backup lamp 1. Remove the two push-pins from the taillamp housing. 2. Grasp the taillamp and pull firmly to disengage the lamp from the aperture panel...

  • Page 482

    Fluid capacities u.S. Metric fuel (approximate) 13.6 gallons 51.5 liters engine oil with filter 2.0l and 2.4l engine (sae 5w-20, api certified) 4.5 quarts 4.26 liters cooling system * 2.0l and 2.4l engine (mopar® antifreeze/ engine coolant 10 year/150,000 mile formula or equivalent) 7.2 quarts 6.8 l...

  • Page 483

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standard ms-12106. Engine o...

  • Page 484

    Chassis component fluid, lubricant, or genuine part automatic transmission (cvt) – if equipped we recommend you use mopar® cvtf+4® continuously variable transmission fluid. Manual transmission – if equipped we recommend you use mopar® atf+4® automatic transmission fluid. Rear drive assembly (rda) we...

  • Page 485: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .484 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .486 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 486

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 487

    Note: under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km) or twelve months, whichever comes first. Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire inflation pressures and look for unusual wear or dam...

  • Page 488

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 489

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 490

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 491

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 492

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to per- form a service job, take your vehicle to a competent mechanic. • failure to properly inspect and m...

  • Page 493: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . .493 ▫ prepare for the appointment. . . . . . . . . . . . .493 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .493 ▫ be reasonable with requests . . . . ....

  • Page 494

    䡵 department of transportation uniform tire quality grades . . . . . . . . .499 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .499 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .500 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .500 492 if you need consum...

  • Page 495

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 496

    Warranty service must be done by an authorized dealer. We strongly recommend that you take the vehicle to an authorized dealer. They know your vehicle the best, and are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trai...

  • Page 497

    Chrysler canada inc. Customer center p.O. Box 1621 windsor, ontario n9a 4h6 phone: (800) 465–2001 english / (800) 387–9983 french in mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer ass...

  • Page 498

    Service contract you may have purchased a service contract for a vehicle to help protect you from the high cost of unexpected repairs after the manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufactur...

  • Page 499

    Warning! (continued) birth defects, or other reproductive harm. In addi- tion, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemi- cals known to the state of california to cause cancer and birth defects, or other reproductive harm. Warranty informatio...

  • Page 500

    Washington, d.C. 20590. You can also obtain other infor- mation about motor vehicle safety from http:// www.Safercar.Gov. In canada if you believe that your vehicle has a safety defect, you should contact the customer service department imme- diately. Canadian customers who wish to report a safety d...

  • Page 501

    The first time, using step-by-step troubleshooting and driv- ability procedures, proven diagnostic tests and a complete list of all tools and equipment. Owner’s manuals these owner’s manuals have been prepared with the assistance of service and engineering specialists to ac- quaint you with specific...

  • Page 502

    Significantly from the norm due to variations in driving habits, service practices, and differences in road charac- teristics and climate. Traction grades the traction grades, from highest to lowest, are aa, a, b, and c. These grades represent the tire’s ability to stop on wet pavement, as measured ...

  • Page 503

    Warning! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure. 9 if you need consumer assistance 501.

  • Page 505: Index

    Index 10

  • Page 506

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .339 adding engine coolant (antifreeze) . . . . . . . . . . . .456 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .388 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .450 additives, fuel . . . . . . . . . ...

  • Page 507

    Fluid and filter changes . . . . . . . . . . . . . . . . . .463 fluid level check . . . . . . . . . . . . . . . . . . . . . . .463 fluid type . . . . . . . . . . . . . . . . . . . . . . . . . . . .462 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . .325 special additives . . . . . . ...

  • Page 508

    Luggage carrier . . . . . . . . . . . . . . . . . . . . . . . .205 cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198 cargo load floor . . . . . . . . . . . . . . . . . . . . . . . . .201 cargo tie-downs . . . . . . . . . . . . . . . . . . . . . . . . .201 car washes . . . . . ...

  • Page 509

    Coolant level . . . . . . . . . . . . . . . . . . . . . . . . . .454 disposal of used coolant . . . . . . . . . . . . . . . . .457 drain, flush, and refill . . . . . . . . . . . . . . . . . . .454 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .458 points to remember . . . . . . . ...

  • Page 510

    Electronic speed control (cruise control) . . . . . . . .173 electronic stability control (esc) . . . . . . . . . . . . . .348 electronic vehicle information center (evic) . . . . . .230 emergency, in case of jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .410 jump starting . . ...

  • Page 511

    Flashers hazard warning . . . . . . . . . . . . . . . . . . . . . . . .408 turn signal . . . . . . . . . . . . . . . . . . . . . . . . . . .102 flooded engine starting . . . . . . . . . . . . . . . . . . . .319 fluid, brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .482 fluid capacitie...

  • Page 512

    Garage door opener (homelink®) . . . . . . . . . . . .176 gas cap (fuel filler cap) . . . . . . . . . . . . . . . . . . .388 gasoline, clean air . . . . . . . . . . . . . . . . . . . . . . . .385 gasoline (fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . .384 gasoline, reformulated . . . . ...

  • Page 513

    Homelink® (garage door opener) . . . . . . . . . . . .176 hood release . . . . . . . . . . . . . . . . . . . . . . . . . . . .161 ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 ignition key remova...

  • Page 514

    Lead free gasoline . . . . . . . . . . . . . . . . . . . . . . . .384 leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .370 liftgate (sedan) . . . . . . . . . . . . . . . . . . . . . . . . . . .38 liftgate...

  • Page 515

    Security alarm (theft alarm) . . . . . . . . . . . . . . . .19 service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .478 theft alarm (security alarm) . . . . . . . . . . . . . . .219 tire pressure monitoring (tpms) . . . . . . . . . . . .221 traction control . . . . . . . . . . . . . ...

  • Page 516

    Exterior folding . . . . . . . . . . . . . . . . . . . . . . . .109 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 vanity . . . . . . ...

  • Page 517

    Overheating, engine . . . . . . . . . . . . . . . . . . . . . . .220 owner’s manual (operator manual) . . . . . . . . . . . . .5 paint care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .465 panic alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 parking brake. . . . . ...

  • Page 518

    Rear window features . . . . . . . . . . . . . . . . . . . . .203 rear wiper/washer. . . . . . . . . . . . . . . . . . . . . . . .203 recorder, event data . . . . . . . . . . . . . . . . . . . . . . .75 recreational towing . . . . . . . . . . . . . . . . . . . . . . .406 reformulated gasoline . . . ...

  • Page 519

    Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 adjustable shoulder belt . . . . . . . . . . . . . . . . . . .49 adjustable upper shoulder anchorage . . . . . . . . .49 and pregnant women . . . . . . . . . . . . . . . . . . . . .62 child restraint . . . . . . . . . . . ....

  • Page 520

    Speedometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . .215 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .317 automatic transmission . . . . . . . . . . . . . . . . . .318 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . .319 engine fails to start ...

  • Page 521

    General information . . . . . . . . . . . . . . . . . . . . .362 high speed . . . . . . . . . . . . . . . . . . . . . . . . . . .365 inflation pressures . . . . . . . . . . . . . . . . . . . . . . .363 jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .410 life of tires . . . . . ....

  • Page 522

    Transaxle automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 transmission automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .323 fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .462 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 523

    Washer adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .450 washers, windshield . . . . . . . . . . . . . . . . . . . . . . .170 washing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .466 wheel and wheel trim . . . . . . . . . . . . . . . . . . . . .467 wheel and wheel tri...

  • Page 524

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 525

    Patriot 2 0 1 3.