1. DL manuals
  2. Jeep
  3. Automobile
  4. Compass 2013
  5. Owner's Manual

Jeep Compass 2013 Owner's Manual

Other manuals for Compass 2013: User Manual, User Manual, Owner's Manual

Summary of Compass 2013

  • Page 1

    Compass chrysler group llc o w n e r ’ s m a n u a l 2013 c ompas s 13mk49-126-aa first edition printed in u.S.A. 2 0 1 3.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 ...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    Control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat belts pro- vided is a major cause of severe or fatal injury. In fact, the u.S. Government notes that the unive...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right front body vin location 8 introduct...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder. . . . . . . . . . . . . . . . .14 䡵 sentr...

  • Page 12

    ▫ sound horn with remote key lock . . . . . . . . .22 ▫ flash lights with remote key lock/unlock . . .23 ▫ using the panic alarm . . . . . . . . . . . . . . . . . .24 ▫ programming additional transmitters. . . . . . . .24 ▫ general information . . . . . . . . . . . . . . . . . . . .24 ▫ transmitter ...

  • Page 13

    ▫ energy management feature . . . . . . . . . . . . . .54 ▫ seat belt pretensioners . . . . . . . . . . . . . . . . . .55 ▫ supplemental active head restraints (ahr) — if equipped . . . . . . . . . . . . . . . . . . .55 ▫ enhanced seat belt use reminder system (beltalert 威 ) . . . . . . . . . . . . ...

  • Page 14

    A word about your keys the authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition key removal 1. Place the shift lever in...

  • Page 15

    Note: if you try to remove the key before you place the shift lever in park, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in park, rotate the key to the right slightly, then remove the key as described. If a malfunc- tion occurs, the...

  • Page 16

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 17

    Sentry key 姞 the sentry key 威 immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded ...

  • Page 18

    Caution! The sentry key 威 immobilizer system is not compat- ible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehicle electronic...

  • Page 19

    Customer key programming if you have two valid sentry keys 威 , you can program new sentry keys 威 to the system by performing the following procedure: 1. Cut the additional sentry key 威 transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ig...

  • Page 20

    Authorized dealer at the time of service to be repro- grammed. General information the sentry key 威 system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accep...

  • Page 21

    Alarm will automatically disarm. After approximately 16 seconds, the vehicle security light will flash slowly. This shows that the vehicle security alarm is fully armed. Rearming the system if something triggers the alarm, and no action is taken to disarm it, the vehicle security alarm will turn off...

  • Page 22

    Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances up to approximately 66 ft (20 m) using a hand-held remote keyless entry (rke) transmitter. The rke transmitter does not need to be pointed at the vehicl...

  • Page 23

    (customer-programmable features)” in “understand- ing your instrument panel” for further information. • for vehicles not equipped with the evic, perform the following steps: 1. Press and hold the lock button on a programmed rke transmitter for at least 4 seconds, but no longer than 10 seconds. Then,...

  • Page 24

    To lock the doors and liftgate press and release the lock button on the rke transmit- ter to lock all doors and liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Sound horn with remote key lock this feature will cause the horn to chirp when the doors are ...

  • Page 25

    Unlock button to deactivate the vehicle security alarm. Flash lights with remote key lock/unlock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proce...

  • Page 26

    Using the panic alarm to turn the panic alarm feature on or off, press and hold the panic button on the rke transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on. The...

  • Page 27

    2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or cb radios. Transmitter battery replacement note: perchlorate material – special handling may ap- ply. See www.Dtsc.Ca.Gov/hazardouswaste/perchlorate the recommended replacement b...

  • Page 28

    Note: if the rke transmitter is equipped with a screw, reinstall and tighten the screw until snug. Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system...

  • Page 29

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Carbon monoxide is poisonous and can cause serious in- jury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 30

    Note: • the park lamps will turn on and remain on during remote start mode. • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the remote start mode. • if your power door locks were unlocked, remote start will automatically lock the doors. • ...

  • Page 31

    To exit remote start mode and drive the vehicle before the end of the 15-minute cycle, press and release the unlock button on the rke transmitter to unlock the doors and disarm the vehicle security alarm (if equipped). Then, insert the key into the ignition switch and turn the switch to the on/run p...

  • Page 32

    Warning! (continued) • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allow...

  • Page 33

    Auto lock doors — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer. Please see your authorized d...

  • Page 34

    2. Within 15 seconds, cycle the ignition switch between lock and on/run and then back to lock four times ending up in the lock position (do not start the engine). 3. Within 30 seconds, press the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the programmi...

  • Page 35

    Equipped/personal settings (customer- programmable features)” in “understanding your in- strument panel” for further information. • for vehicles not equipped with the evic, perform the following procedure: 1. Close all doors and place the key in the ignition. 2. Within 15 seconds, cycle the ignition...

  • Page 36

    3. Repeat steps 1 and 2 for the opposite rear door. Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Child-protection door lock location child-protection door lock function 34 thi...

  • Page 37

    Note: for emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window and open the door with the outside door handle. Power windows — if equipped power window switches the window controls on the driver’s door trim panel control all the door windows. There ...

  • Page 38

    Warning! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto-down the driver’s door window switch...

  • Page 39

    Window lockout switch the window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lockout switch. To enable the window con- trols, press the window lockout switch a second time. Liftga...

  • Page 40

    Once unlocked, the liftgate can be opened or closed without using the key. To open the liftgate, squeeze the liftgate release and pull the liftgate open with one fluid motion. Note: • in the event of a power malfunction, or the rke transmitter is inoperative, insert the key into the liftgate lock cy...

  • Page 41

    Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are c...

  • Page 42

    • knee bolsters for front seat occupants • front seat belts incorporate pretensioners that may enhance occupant protection by managing occupant energy during an impact event • all seat belt systems (except the driver’s) include automatic locking retractors (alrs), which lock the seat belt webbing in...

  • Page 43

    Warning! Infants in rear facing child restraints should never ride in the front seat of a vehicle with a passenger advanced front air bag. An air bag deployment can cause severe injury or death to infants in that position. Children that are not big enough to wear the vehicle seat belt properly (see ...

  • Page 44

    Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belts even though you have air bags. • being too close to the steeri...

  • Page 45

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 46

    Warning! (continued) • wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • two pe...

  • Page 47

    Warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden stop you...

  • Page 48

    Warning! (continued) • a belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause inter- nal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your...

  • Page 49

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt may not protect you properly. In a collisi...

  • Page 50

    Adjustable upper shoulder belt anchorage in the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the anchorage button to release the anchorage, and move it up or down to the position that fits you best. Note: the adjustable upper shoulde...

  • Page 51

    In the rear seat, move toward the center of the seat to position the belt away from your neck. Second row center lap/shoulder belt operating instructions the second row center lap/shoulder belt features a three-point seat belt with a mini-latch and buckle, which allows the shoulder belt to detach fr...

  • Page 52

    3. Route the shoulder belt to the inside of the right head restraint. 4. When the belt is long enough to fit, insert the mini- latch plate into the mini-buckle until you hear a “click.” 5. Sit back in the seat. Slide the regular latch plate up the webbing as far as necessary to allow the belt to go ...

  • Page 53

    7. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 8. Position the shoulder bel...

  • Page 54

    10. To disengage the mini-latch from the mini-buckle for storage, insert the regular latch plate into the black button on the top of the mini-buckle. The belt will automatically retract to its stowed position. If neces- sary, slide the latch plate down the webbing to allow the belt to retract fully....

  • Page 55

    • n/a — not applicable • alr — automatic locking retractor if the passenger seating position is equipped with an alr and is being used for normal usage: only pull the belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activa...

  • Page 56

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the belt and retractor assembly must be replaced if the seat belt ...

  • Page 57

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 58

    When ahrs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the ahr. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear imp...

  • Page 59

    Caution! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. Note: for more information on properly adjusting and positi...

  • Page 60

    3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 4. The ahr front soft foam and trim half should lock into the back decorative plastic half. 1 — downward movement 2 — rearward movement 3 — final downward movement to engage locking mechanism 58 thi...

  • Page 61

    Note: • if you have difficulties or problems resetting the active head restraints, see an authorized dealer. • for safety reasons, have the active head restraints checked by a qualified specialist at an authorized dealer. Enhanced seat belt use reminder system (beltalert 姞 ) beltalert 威 is a feature...

  • Page 62

    Unbuckled while traveling at speeds greater than 5 mph (8 km/h), beltalert 威 will provide both audio and visual notification. The front passenger seat beltalert 威 is not active when the front passenger seat is unoccupied. Beltalert 威 may be triggered when an animal or heavy object is on the front pa...

  • Page 63

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt lo...

  • Page 64

    The advanced front air bags have a multistage inflator design. This allows the air bag to have different rates of inflation that are based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation ...

  • Page 65

    • instrument panel • knee impact bolster • driver advanced front air bag • passenger advanced front air bag • supplemental seat-mounted side air bags (sab) • supplemental side air bag inflatable curtains (sabic) • front and side impact sensors • front seat belt pretensioners, seat belt buckle switch...

  • Page 66

    Warning! (continued) • do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air ba...

  • Page 67

    When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental side air bag inflatable curtain (sabic) sabic air...

  • Page 68

    • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • being too close to the supplemental side air bag inflatable curtain and/or seat-mounted side air bag during deployment could cause you to be severely injured or killed. The system includes side ...

  • Page 69

    Windows, or area where the sab or sabic air bags inflate, even if they are in an infant or child restraint. Always sit upright as possible with your back against the seat back, use the seat belts properly, and use the appropriate sized child restraint, infant restraint or booster seat recommended fo...

  • Page 70

    Including the severity and type of collision. Advanced front air bags are not expected to reduce the risk of injury in rear, side, or rollover collisions. The advanced front air bags will not deploy in all frontal collisions, including some that may produce sub- stantial vehicle damage — for example...

  • Page 71

    Turns on the air bag warning light, either momentarily or continuously. A single chime will sound if the light comes on again after initial startup. It also includes diagnostics that will illuminate the instru- ment cluster air bag warning light if a malfunction is noted that could affect the air ba...

  • Page 72

    The advanced front air bag gas is vented through the vent holes in the sides of the air bag. In this way, the air bags do not interfere with your control of the vehicle. Supplemental seat-mounted side air bag (sab) inflator units the supplemental seat-mounted side air bags (sab) are designed to acti...

  • Page 73

    Inflates. This especially applies to children. The side curtain air bag is only about 3-1/2 in (9 cm) thick when it is inflated. Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an air bag should have deployed. Note: in a rol...

  • Page 74

    Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision, which deploys the air bags, any or all of the following may occur: • the nylon air bag material may sometimes cause abrasions and/or skin red...

  • Page 75

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 76

    Air bag warning light you will want to have the air bags ready to inflate for your protection in a collision. The air bag warning light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenan...

  • Page 77

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 78

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Chil...

  • Page 79

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 80

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 81

    Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direc- tion are for children who are over two ye...

  • Page 82

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 83

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 84

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 85

    Latch positions for installing child restraints in this vehicle lower anchorage symbol 2 anchorages per seating position top tether anchorage symbol 2 things to know before starting your vehicle 83.

  • Page 86

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 87

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 88

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between ...

  • Page 89

    Restraints with flexible, webbing mounted lower attach- ments can be installed in any rear seating position. Warning! Never use the same lower anchorage to attach more than one child restraint. If you are installing latch- compatible child restraints next to each other, you must use the seat belt fo...

  • Page 90

    4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 91

    Warning! Improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. Installing child restraints using...

  • Page 92

    Lap/shoulder belt systems for installing child restraints in this vehicle 90 things to know before starting your vehicle.

  • Page 93

    What is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint, ...

  • Page 94

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. 2. Pull enough of the seat belt webbing fro...

  • Page 95

    9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. Installing a...

  • Page 96

    Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. If the buckle or the cinching latch plate is too close to the belt path opening of the child restraint, you may have trouble tightening the seat belt. If this happens, discon- nect the latch p...

  • Page 97

    4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly be- hind the child seat to secure a child res...

  • Page 98

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 99

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be serious...

  • Page 100

    Warning! (continued) • if it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained ...

  • Page 101

    Air bag warning light the light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned on. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked...

  • Page 102

    Warning! (continued) • never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfer- ing with the pedals or the ability to control the vehicle. • never put floor mats or other floor coverings on top of already inst...

  • Page 103

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 105: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 ▫ inside day/night mirror . . . . . . . . . . . . . . . .107 ▫ automatic dimming mirror — if equipped . . .108 ▫ outside mirror — driver side . . . . . . . . . . . .109 ▫ outside ...

  • Page 106

    ▫ commands . . . . . . . . . . . . . . . . . . . . . . . . . .144 ▫ voice training . . . . . . . . . . . . . . . . . . . . . . . .147 䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 ▫ power seats — if equipped . . . . . . . . . . . . . .148 ▫ heated seats — if equipped . . . ....

  • Page 107

    䡵 windshield wipers and washers . . . . . .168 ▫ windshield wiper operation . . . . . . . . . . . . .169 ▫ intermittent wiper system . . . . . . . . . . . . . . .170 ▫ windshield washers . . . . . . . . . . . . . . . . . . .170 ▫ mist feature . . . . . . . . . . . . . . . . . . . . . . . . .171 䡵 ti...

  • Page 108

    ▫ closing sunroof — express. . . . . . . . . . . . . . .186 ▫ closing sunroof — manual mode . . . . . . . . . .186 ▫ pinch protect feature . . . . . . . . . . . . . . . . . . .186 ▫ venting sunroof — express . . . . . . . . . . . . . .187 ▫ sunshade operation. . . . . . . . . . . . . . . . . . . .18...

  • Page 109

    Mirrors inside day/night mirror a two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicl...

  • Page 110

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 111

    Outside mirror — driver side adjust the flat outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the door glass. Outside mirror — passenger side adjust the convex outside mirror so you can just see the side of your vehi...

  • Page 112

    Power mirrors the power mirror control is located on the driver’s door trim panel. To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the c...

  • Page 113

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “rear window features” in “understanding the features of your vehicle” for further information. Vanity mirrors — if equipped to use the vanit...

  • Page 114

    Uconnect™ phone — if equipped uconnect™ phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ phone al- lows you to dial a phone number with your mobile phone using simple voice commands (e.G., “call” ѧ “mike” ѧ “work” or “dial” ѧ “248-555-1212”). Your mobile phone’s a...

  • Page 115

    Used with the system at a time. The system is available in english, spanish, or french languages. Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. All atten- tion should be kept on the roadway ahead....

  • Page 116

    The radio display will be used for visual prompts from the uconnect™ phone such as “cell” or caller id on certain radios. Operation voice commands can be used to operate the uconnect™ phone and to navigate through the uconnect™ phone menu structure. Voice commands are required after most uconnect™ p...

  • Page 117

    To activate the uconnect™ phone, simply press the button and follow the audible prompts for direc- tions. Uconnect™ phone sessions begin with a press of the button on the radio control head. Cancel command at any prompt, after the beep, you can say “cancel” and you will be returned to the main menu....

  • Page 118

    • you will then be asked to give your mobile phone a priority level between one and seven, with one being the highest priority. You can pair up to seven mobile phones to your uconnect™ phone. However, at any given time, only one mobile phone can be in use, connected to your uconnect™ system. The pri...

  • Page 119

    Or downloaded phonebook. To learn how to store a name in the phonebook, refer to “add names to your uconnect™ phonebook”, in the phonebook. • the uconnect™ system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Add names to your ...

  • Page 120

    Phonebook download – automatic phonebook transfer from mobile phone if equipped and specifically supported by your phone, uconnect™ phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific bluetooth 威 phones with phone book access profile may s...

  • Page 121

    Edit uconnect™ phonebook entries note: • editing names in the phonebook is recommended when the vehicle is not in motion. • automatic downloaded phonebook entries cannot be deleted or edited. • press the button to begin. • after the “ready” prompt and the following beep, say “phonebook edit entry”. ...

  • Page 122

    • after you enter the phonebook delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say “list names” to hear a list of the entries in the phonebook from which you choose. To select ...

  • Page 123

    • after the “ready” prompt and the following beep, say “phonebook list names”. • the uconnect™ phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available. • to call one of the names in the list, press the but- ton during the playing of the desi...

  • Page 124

    Mobile phone. Press the button to place the current call on hold and answer the incoming call. Note: the uconnect™ phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it...

  • Page 125

    Three-way calling to initiate three-way calling, press the button while a call is in progress, and make a second phone call, as described under “making a second call while current call is in progress”. After the second call has established, press and hold the button until you hear a double beep, ind...

  • Page 126

    Ends, or until the vehicle battery condition dictates cessation of the call on the uconnect™ phone and transfer of the call to the mobile phone. • after the ignition key is switched to off, a call can continue on the uconnect™ phone for a certain dura- tion, after which the call is automatically tra...

  • Page 127

    If the phone is not reachable and the uconnect™ phone is operational, you may reach the emergency number as follows: • press the button to begin. • after the “ready” prompt and the following beep, say “emergency” and the uconnect™ phone will instruct the paired mobile phone to call the emergency num...

  • Page 128

    • after the “ready” prompt and the following beep, say “roadside assistance”. Note: • the roadside assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the u.S., 1-877-213-4525 for canada, 55-14- 3454 for mexico city and 1-800-712-3040 for outside mexi...

  • Page 129

    On your mobile phone keypad, you can press the button and say the sequence you wish to enter, followed by the word “send”. For example, if required to enter your pin followed with a pound, (3 7 4 6 #), you can press the button and say, “3 7 4 6 # send”. Saying a number, or sequence of numbers, follo...

  • Page 130

    Turning confirmation prompts on/off turning confirmation prompts off will stop the system from confirming your choices (e.G., the uconnect™ phone will not repeat a phone number before you dial it). • press the button to begin. • after the “ready” prompt and the following beep, say one of the followi...

  • Page 131

    Mute/un-mute (mute on/off) when you mute the uconnect™ phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect™ phone: • press the button. • following the beep, say “mute”. In order to un-mute...

  • Page 132

    • when prompted, say “list phones”. • the uconnect™ phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the button and say “select” or “delete”. Also, see the next two sections for...

  • Page 133

    Things you should know about your uconnect™ phone uconnect™ phone tutorial to hear a brief tutorial of the system features, press the button and say “uconnect™ tutorial.” voice training for users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect™ pho...

  • Page 134

    This will delete all phone pairing, phone book entries, and other settings in all language modes. The system will prompt you before resetting to factory settings. Voice command • for best performance, adjust the rearview mirror to provide at least ½ in (1 cm) gap between the overhead console (if equ...

  • Page 135

    • phonebook (downloaded and uconnect™ phone lo- cal) name recognition rate is optimized when the entries are not similar. • numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • you can say “o” (letter “o”) for “0” (zero). • even though international ...

  • Page 136

    Sms uconnect™ phone can read or send new messages on your phone. Read messages: if you receive a new text message while your phone is connected to uconnect™ phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • press the button. • ...

  • Page 137

    List of preset messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L o l 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See you in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18....

  • Page 138

    Turn sms incoming announcement on/off turning the sms incoming announcement off will stop the system from announcing the new incoming mes- sages. • press the button. • after the “ready” prompt and the following beep, say “setup, sms incoming message announcement,” you will then be given a choice to ...

  • Page 139

    3 understanding the features of your vehicle 137.

  • Page 140

    138 understanding the features of your vehicle.

  • Page 141

    3 understanding the features of your vehicle 139.

  • Page 142

    Voice commands primary alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all call voice commands primary alternate (s) cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help home language...

  • Page 143

    Voice commands primary alternate (s) list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again redial voice commands primary alternate (s) return to main menu return or main menu select phone select send set up phone settings or...

  • Page 144

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment....

  • Page 145

    Warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws. All attention should be kept on the roadway ahead. Failure to do so may result in a collision causing serious injury or death. When you press the voice command button, you will hear a be...

  • Page 146

    To hear the first available menu, press the voice com- mand button and say “help” or “main menu”. Commands the voice command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the volum...

  • Page 147

    • “previous station” (to select the previous station) • “radio menu” (to switch to the radio menu) • “main menu” (to switch to the main menu) radio fm to switch to the fm band, say “fm” or “radio fm”. In this mode, you may say the following commands: • “frequency #” (to change the frequency) • “next...

  • Page 148

    Disc to switch to the disc mode, say “disc”. In this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) memo to switch to the voice recorder m...

  • Page 149

    • “change to setup” • “main menu setup” or • “switch to setup” in this mode, you may say the following commands: • “language english” • “language french” • “language spanish” • “tutorial” • “voice training” note: keep in mind that you have to press the voice command button first and wait for the bee...

  • Page 150

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 151

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 152

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the center instrument panel area. You can choose from high, low or off heat settings. Amber ind...

  • Page 153

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Man...

  • Page 154

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 155

    Driver’s seatback recline to adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired angle and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Warning! Do not ride with the seatback reclined so that the sho...

  • Page 156

    Fold-flat front passenger seat to fold the front passenger seat, lift the recliner handle to the full upward position and push the seatback forward until it rests on the seat cushion. Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event ...

  • Page 157

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 158

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. For comfort the active head restraints can be tilted forward and backward. To tilt the head restrain...

  • Page 159

    Note: • the head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer. • in the event of deployment of an active head re- straint, refer to “occupant restraints/resetting active head re...

  • Page 160

    Warning! (continued) • active head restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the ac- tive head restraint ensure that all cargo is secured, as loose cargo could contact the active head re- straint during sudden st...

  • Page 161

    To raise the seatback, pull the strap forward and lift the seatback into its upright position. Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers...

  • Page 162

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only with the vehicle is parked. To open and close the hood to open the hoo...

  • Page 163

    2. Move the safety latch, located outside the vehicle under the front edge of the hood, toward the center and raise the hood. Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment to secure the hood in the open position. Place the hood prop at the locati...

  • Page 164

    Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 8 in (20 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is ful...

  • Page 165

    Headlights and parking lights turn the end of the multifunction lever to the first detent to turn on the parking lights. Turn the end of the lever to the second detent to turn on the headlights. Daytime running lights — if equipped the high beam lights will come on as daytime running lights (lower i...

  • Page 166

    Fog lights — if equipped the front fog light switch is on the multifunction lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the multifunction lever. Note: the fog lights will only operate with the head- lights on low beam. Select...

  • Page 167

    Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. Lane change assist tap the lever up or down once, without ...

  • Page 168

    Instrument panel dimming rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument pane...

  • Page 169

    Map/reading lights these lights are mounted between the sun visors above the rear view mirror. Each light is turned on by pressing the button. Press the button a second time to turn the light off. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the se...

  • Page 170

    Windshield wipers and washers the windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “rear window fea- tures” in “understand...

  • Page 171

    Caution! • turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • in cold weather, always turn off the wiper switch and allow the wipers to return to the “park” posi- tion be...

  • Page 172

    Intermittent wiper system use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Select the delay interval by turning the end of the lever. Rotate the end of the lever upward (clockwise) to decrease the delay time and downwar...

  • Page 173

    Mist feature push down on the control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Note: the mist feature does not activate the washer pump; therefore, no washer fluid wil...

  • Page 174

    Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Push the lever up to lock the steering column firmly in place. Warning! Do not adjust the steering column while driving. Adjusting the steering column wh...

  • Page 175

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 176

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 177

    To decrease speed while the electronic speed control is set, push the set (-) button. If the button is continually held in the set (-) position, the set speed will continue to decrease until the button is released. Release the button when the desired speed is reached, and the new set speed will be e...

  • Page 178

    Garage door opener — if equipped homelink 威 replaces up to three hand-held transmitters that operate devices such as garage door openers, motor- ized gates, lighting or home security systems. The homelink 威 unit is powered by your vehicles 12 volt battery. The homelink 威 buttons, located on either t...

  • Page 179

    Note: homelink 威 is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink 姞 be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is rec...

  • Page 180

    Programming a rolling code for programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “learn” or “train” button located where the hanging antenna is attached to the garage door opener. It is not the button that is normally used to open...

  • Page 181

    2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink 威 button you wish to pro- gram while keeping the homelink 威 indicator light in view. 3. Simultaneously press and hold both the homelink 威 button you want to program and the hand-held trans- mitter button. 4. Continue to ...

  • Page 182

    Reprogramming a single homelink 威 button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press and hold the desired homelink 威 button until the indicator light begins to flash after 20 seconds. Do not release the but...

  • Page 183

    • to program the two remaining homelink 威 buttons, repeat each step for each remaining button. Do not erase the channels. Reprogramming a single homelink 威 button to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. 2. Press...

  • Page 184

    2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink 威 button you wish to pro- gram while keeping the homelink 威 indicator light in view. 3. Continue to press and hold the homelink 威 button, while you press and release (“cycle”), your hand-held transmitter every two second...

  • Page 185

    3. Without releasing the button proceed with “canadian/gate operator programming” step 2 and follow all remaining steps. Using homelink 姞 to operate, press and release the programmed homelink 威 button. Activation will now occur for the programmed device (i.E., garage door opener, gate opera- tor, se...

  • Page 186

    Warning! • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” fea...

  • Page 187

    Power sunroof — if equipped the power sunroof switch is located on the overhead console. Warning! • never leave children in a vehicle with the key in the ignition switch (or with the ignition in the accessory or run position, for vehicles equipped with keyless enter-n-go™). Occupants, particu- larly...

  • Page 188

    Opening sunroof — express press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- cally. This is called “express open”. During express open operation, any movement of the sunroof switch ...

  • Page 189

    Note: if three consecutive sunroof close attempts re- sult in pinch protect reversals, the fourth close attempt will be a manual close movement with pinch protect disabled. Venting sunroof — express press and release the vent button within one half second and the sunroof will open to the vent positi...

  • Page 190

    Ignition off operation for vehicles not equipped with the electronic vehicle information center (evic) the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the lock position. Opening either front door will cancel this feature. For vehicles equipped with t...

  • Page 191

    Note: to ensure proper operation a mopar 威 knob and element must be used. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watt (13 amp) power rating is exceeded the fuse protecting the system will need to be replaced. • power outlets are designed for accesso...

  • Page 192

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 193

    Power inverter — if equipped a 115 volt (150 watt) ac power inverter is located on the front of the center console for added convenience. This outlet can power mobile phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such as playstation3 a...

  • Page 194

    Warning! To avoid serious injury or death: • do not use a three-prong adaptor. • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories tha...

  • Page 195

    Cupholders your vehicle is equipped with four cupholders. There are two illuminated cupholders located in the front. There are two cupholders located in the back for the rear passengers. Front cupholders rear cupholders 3 understanding the features of your vehicle 193.

  • Page 196

    Storage glove compartment and storage bin located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. To open the lower glove compartment, pull outward on the release handle. Storage bins 1 — upper storage bin 2 — lower glove compartment glove compar...

  • Page 197

    Door storage the interior door panels are equipped with lower storage areas. Front door storage rear door storage 3 understanding the features of your vehicle 195.

  • Page 198

    Console features the floor console contains both an upper and lower storage compartment. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. To open the lower storage compartment, lift upward on the lower handle to unlatch the lower ...

  • Page 199

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injur...

  • Page 200

    To operate the flashlight, press the switch once for high, twice for low, and a third time to return to off. Cargo cover the cargo area trim panels include two notches for mounting the available tonneau cover that accommo- dates the reclining rear seat. To install the cargo cover, insert either end ...

  • Page 201

    Using the handle, pull the cover toward you and guide the rear cover posts into the guides located on both sides of the rear trim panel. Warning! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store...

  • Page 202

    Removable load floor the cargo area load floor is removable and can be washed with mild soap and water. Cargo tie-down loops there are four tie-downs (d-rings) installed in the cargo area for securing cargo. Removable load floor cargo area tie-downs 200 understanding the features of your vehicle.

  • Page 203

    Warning! • cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • the weight and position of cargo a...

  • Page 204

    Fold down speakers — if equipped when the liftgate is open, the speakers can swing down off the trim panel to face rearward, for tailgating and other activities. Rear window features rear window wiper/washer the rear wiper/washer is controlled by a rotary switch located on the center portion of the ...

  • Page 205

    Rotate the center portion of the lever upward to the first detent position for rear wiper operation. Note: the rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to op...

  • Page 206

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 207

    The optional crossbars must also be secured in one of the seven detent positions marked with an arrow on the siderails to prevent movement. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately eight turns, then move the crossbar to the desired posit...

  • Page 208

    Caution! • to prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other prot...

  • Page 209: Contents

    Understanding your instrument panel contents 䡵 instrument panel features. . . . . . . . . . .210 䡵 instrument cluster . . . . . . . . . . . . . . . . .211 䡵 instrument cluster descriptions . . . . .212 䡵 mini-trip computer — if equipped . . . . .226 ▫ control buttons . . . . . . . . . . . . . . . . ...

  • Page 210

    ▫ operation instructions - (disc mode for cd and mp3/wma audio play, dvd-video) . . .248 ▫ list button (disc mode for mp3/wma play). . . . . . . . . .253 ▫ info button (disc mode for mp3/wma play). . . . . . . . . .253 ▫ uconnect™ multimedia (satellite radio) — if equipped . . . . . . . . . . . . . ...

  • Page 211

    ▫ uconnect™ multimedia (satellite radio) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .282 䡵 ipod 威 /usb/mp3 control — if equipped . .287 ▫ connecting the ipod 威 or external usb device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .288 ▫ using this feature. . . . . . ....

  • Page 212

    Instrument panel features 1 — air outlet 5 — storage bin 9 — heated seat switch – if equipped 2 — demisters 6 — glove compartment 10 — hazard warning flasher 3 — instrument cluster 7 — climate controls 11 — esc off switch – if equipped 4 — radio 8 — power outlet 12 — heated seat switch – if equipped...

  • Page 213

    Instrument cluster 4 understanding your instrument panel 211.

  • Page 214

    Instrument cluster descriptions 1. Fuel gauge / fuel door reminder when the ignition switch is in the on/run position, the pointer will show the level of fuel remaining in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 2. Charging system light t...

  • Page 215

    On briefly as a bulb check. If the light does not come on during starting, have the system checked by an autho- rized dealer. 4. Oil pressure warning light this light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while drivi...

  • Page 216

    Alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 9. High beam indicator this indicator shows that the high beam head- lights are on. Push the multifunction lever for- ward to switch the headlights to high beam, and pull toward ...

  • Page 217

    12. Tachometer the white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 13. Engine temperature warning light this light warns of an overheated engine condi- tio...

  • Page 218

    Booster, the abs pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by ...

  • Page 219

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Transmission temperature warning light this light indicates that the t...

  • Page 220

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If ...

  • Page 221

    20. Shift lever indicator the shift lever indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. Note: you must apply the brakes before shifting from park. 21. Odometer/trip odometer reset button press this button to change the display...

  • Page 222

    Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped wi...

  • Page 223

    23. Odometer display / trip odometer display area this display indicates the total distance the vehicle has been driven. Note: u.S. Federal regulations require that upon trans- fer of vehicle ownership, the seller certify to the pur- chaser the correct mileage that the vehicle has been driven. If yo...

  • Page 224

    Note: if the vehicle is equipped with the optional electronic vehicle information center (evic) in the in- strument cluster, all warnings including “door ajar”, and “gate ajar” will only be displayed in the evic display. For additional information, refer to “electronic vehicle information center — i...

  • Page 225

    Engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the on/run position. To turn off the message temporarily, press and release the trip odometer button on the instrument cl...

  • Page 226

    Caution! Prolonged driving with the mil on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warning! A malfunctioning catalytic ...

  • Page 227

    System. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. Note: the “esc off indicator light” and the ...

  • Page 228

    Mini-trip computer — if equipped the mini-trip computer is located in the instrument cluster and features a driver-interactive trip information and temperature display. Note: the system will display the last known outside temperature when starting the vehicle and may need to be driven several minute...

  • Page 229

    Reset button to reset the display shown, turn the ignition switch to the on position, then press and hold the reset button located on the steering wheel. The following displays can be reset or changed: • trip a • trip b trip odometer (odo) this display shows the distance traveled since the last rese...

  • Page 230

    Electronic vehicle information center (evic) — if equipped the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • vehicle information warning message displays • personal...

  • Page 231

    The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: menu button press and release the menu button to scroll through the main menus (fuel economy, warn- ings, timer, units, system, personal settings) or to exit sub-menus. Compass button ...

  • Page 232

    Down button press and release the down button to scroll downward through the sub-menus. When the appropriate conditions exist, the evic displays the following messages: • turn signal on (with a continuous warning chime after 1 mile (1.6 km) of distance travelled) • left front turn signal lamp out (w...

  • Page 233

    • remote start aborted — fuel low • remote start aborted — system fault • key in ignition • low tire • low tire pressure display for premium tpm system • service tpm system engine oil change indicator system — if equipped oil change required your vehicle is equipped with an engine oil change indicat...

  • Page 234

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. Evic functions • compass/temperature/audio • average fuel economy • distance to empty (dte) • units in • elapsed time • tire pressure monitor (tpm...

  • Page 235

    History information will be erased, and the averaging will continue from the last fuel reading before the reset. Distance to empty (dte) shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantan...

  • Page 236

    Reset all digits will change to zeros and time will start incrementing again if the ignition switch is in run or start. Personal settings (customer-programmable features) this allows the driver to set and recall features when the transmission is in park (automatic transmission) or the vehicle is sto...

  • Page 237

    Position (automatic transmission). Press and hold the select button when in this display until “on” or “off” appears to make your selection. Rke unlock driver’s door 1st when driver’s door 1st is selected only the driver’s door will unlock on the first press of the remote keyless entry (rke) transmi...

  • Page 238

    Key off power delay when this feature is selected the power window switches, radio, uconnect™ phone, power sunroof, and power outlets will remain active for up to 10 minutes after the ignition switch has been turned off. Opening either front vehicle door will cancel this feature. Press and hold the ...

  • Page 239

    Automatic compass calibration this compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the evic will display “cal” until the compass is calibrated. You may also calibrate the compass by completing one or more...

  • Page 240

    5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “cal” indicator turns off. The compass will now function normally. Compass variance compass variance is the difference between magnetic north and geographic north. To compensate for the differen...

  • Page 241

    3. Press the down button until “compass variance” message and the last variance zone number displays in the evic. 4. Press and release the select button until the proper variance zone is selected according to the map. 5. Press and release the compass button to exit. Media center 230 (req) — am/fm st...

  • Page 242

    Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Press the on/volume control knob a second time to turn off the radio. Electronic volume control the electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the ...

  • Page 243

    Phone button uconnect™ phone — if equipped press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” for further details. If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect phone” message will ...

  • Page 244

    Rw/ff pressing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in am, fm or satellite (if equipped) frequencies. Tune control turn the rotary tune/scroll control knob clockwise to increase or counter...

  • Page 245

    Music type button pressing this button once will turn on the music type mode for five seconds. Pressing the music type button or turning the tune/scroll control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast music type inf...

  • Page 246

    Program type 16-digit character display soft rhythm and blues soft r & b sports sports talk talk top 40 top 40 weather weather by pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music ty...

  • Page 247

    • dvd play options - selecting the dvd play options will display the following: • subtitle – repeatedly pressing select will switch subtitles to different subtitle languages that are avail- able on the disc (if equipped). • audio stream – repeatedly pressing select will switch to different audio lan...

  • Page 248

    Menu language — if equipped selecting this item will allow the user to choose the default startup dvd menu language (effective only if language supported by disc). If you want to select a language not listed, then scroll down and select ⬙ other. ⬙ enter the four-digit country code using the tune/ sc...

  • Page 249

    Aspect ratio — if equipped selecting this item allows you to choose between wide screen, pan scan, and letter box. Autoplay — if equipped when this is set to on and a dvd video is inserted, it will bypass the dvd menu screen and automatically play the movie. In some rare cases, the dvd player may no...

  • Page 250

    Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the stations that you commit to pushbutton memory {12 am, 12 fm, and 12 satellite (if equipped) stations}. Disc button pressing the disc button will allow you to switch from ...

  • Page 251

    Prompt when to insert disc. After the radio displays ⬙ insert disc, ⬙ insert the cd into the player. Radio display will show ⬙ loading disc ⬙ when the disc is loading and “reading disc” when the radio is reading the disc. Caution! This cd player will accept 4–3/4 in (12 cm) discs only. The use of ot...

  • Page 252

    Time button (cd mode) press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff (cd mode) press and hold ff (fast forward) and the cd player will begin to fast forward until ff is released, or rw or another cd button is pressed. The rw (re...

  • Page 253

    • maximum number of characters in file/folder names: • level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • level 2: 31 (including a separator ⬙ . ⬙ and a three- character extension) multisession disc formats are supported by the radio. Multisession discs may contain combinat...

  • Page 254

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48 wma specification sampling fre- quency (khz) bit rate (kbps) wma 44.1 and 48...

  • Page 255

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. List button (disc mode for mp3/wma play) pressing the list button will bring up a list of all folders on ...

  • Page 256

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Seek button (auxiliary mode) no function. Scan button (auxiliary mode) no functi...

  • Page 257

    Operating instructions - video entertainment system (ves)™ (if equipped) refer to “video entertainment system (ves)™” for fur- ther details. Dolby 威 manufactured under license from dolby 威 laboratories. Dolby 威 and the double-d symbol are trademarks of dolby 威 laboratories. Macrovision this product ...

  • Page 258

    System activation sirius satellite radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, includ...

  • Page 259

    Decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehi...

  • Page 260

    Info button pressing the info button will cycle the display informa- tion between artist, song title, and composer (if avail- able). Also, pressing and holding the info button for an additional three seconds will make the radio display the song title all of the time (press and hold again to return t...

  • Page 261

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set/rnd button — to set the pushbutton memory ...

  • Page 262

    Media center 730n/430/430n (rhr/rer/rbz/ rhb) cd/dvd/hdd/nav — if equipped note: the sales code is located on the lower right side of the unit’s faceplate. Refer to your uconnect™ multimedia rhr, rer, rbz or rhb user’s manual for detailed operating instructions. Operating instructions (voice command...

  • Page 263

    Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electronic volume cont...

  • Page 264

    3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side tune/ scroll control knob. Press the tune/scroll con- trol knob to save time change. 5. To exit, press any button/knob, or wait...

  • Page 265

    Push the rotary tune/scroll control knob a fifth time and fade will display. Turn the tune/scroll control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary tune/scroll control knob again to exit setting tone, balance, and fade. Am/fm button pres...

  • Page 266

    Disc button pressing the disc button will allow you to switch from am/fm modes to disc modes. Operation instructions — cd mode for cd and mp3 audio play note: • the ignition switch must be in the on or acc position to operate the radio. • this radio is capable of playing compact discs (cd), recordab...

  • Page 267

    Eject button - ejecting a cd press the eject button to eject the cd. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the cd is not removed, the radio will reinsert the cd but will not play it. A disc can be ejected with the radio and ignition off. Note: ...

  • Page 268

    Set/rnd button (random play button) press this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right seek button to move to the next ran- domly selected track. Press the ...

  • Page 269

    Display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) • maximum number of characters in file/folder names: • level 1: 12 (including ...

  • Page 270

    Mpeg specification sampling fre- quency (khz) bit rate (kbps) mpeg-1 audio layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 mpeg-2 audio layer 3 24, 22.05, 16 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 id3 tag information for artist, song title, and a...

  • Page 271

    To increase the speed of disc loading, it is recommended to use cd-r media and single-session discs. To create a single-session disc, enable the “disc at once” option before writing to the disc. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack, which allows the...

  • Page 272

    Media center 130 with satellite radio (sales code res+rsc) note: the radio sales code is located on the lower right side of the radio faceplate. Operating instructions — radio mode note: the ignition switch must be in the on or acc position to operate the radio. Power switch/volume control (rotary) ...

  • Page 273

    Seek buttons press and release the seek buttons to search for the next listenable station in am/fm mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations wit...

  • Page 274

    Clock setting procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side tune/ scroll control knob. 3. After adjusting the hours, press the right side tune/ scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the mi...

  • Page 275

    Setting the tone, balance, and fade push the rotary tune/scroll control knob and bass will display. Turn the tune/scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control...

  • Page 276

    Toggle the music type button to select the following format types: program type 16-digit character display no program type or undefined none adult hits adlt hit classical classicl classic rock cls rock college college country country foreign language language information inform jazz jazz news news n...

  • Page 277

    By pressing the seek button when the music type icon is displayed, the radio will be tuned to the next frequency station with the same selected music type name. The music type function only operates when in the fm mode. If a preset button is activated while in the music type (program type) mode, the...

  • Page 278

    The set/rnd button twice and set 2 will show in the display window. Each button can be set for set 1 and set 2 in both am and fm. This allows a total of 12 am and 12 fm stations to be stored into pushbutton memory. The stations stored in set 2 memory can be selected by pressing the pushbutton twice....

  • Page 279

    If you insert a disc with the ignition on and the radio on, the unit will switch from radio to cd mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. Caution! • this cd player will ac...

  • Page 280

    The current selection. Pressing and holding the seek button will allow faster scrolling through the tracks in cd and mp3 modes. Time button press this button to change the display from a large cd playing time display to a small cd playing time display. Rw/ff press and hold ff (fast forward) and the ...

  • Page 281

    Supported media (disc types) the mp3 file recording media supported by the radio are cdda, cd-r, cd-rw, mp3, and cdda+mp3. Supported medium formats (file systems) the medium formats supported by the radio are iso 9660 level 1 and level 2 and includes the joliet extension. When reading discs recorded...

  • Page 282

    Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid mp3 and will not play the file. When using the mp3 encoder to co...

  • Page 283

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 284

    Press and hold the info button again for three seconds to return to ⬙ elapsed time ⬙ display. Operation instructions - auxiliary mode the auxiliary (aux) jack is an audio input jack which allows the user to plug in a portable device such as an mp3 player or cassette player and utilize the vehicle’s ...

  • Page 285

    System activation sirius satellite radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, includ...

  • Page 286

    Decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception quality satellite reception may be interrupted due to one of the following reasons: • the vehi...

  • Page 287

    Info button pressing the info button will cycle the display informa- tion between artist, song title, and composer (if avail- able). Also, pressing and holding the info button for an additional three seconds will make the radio display the song title all of the time (press and hold again to return t...

  • Page 288

    Setup button pressing the setup button allows you to select the following items: • display sirius id number — press the audio/ select button to display the sirius id number. This number is used to activate, deactivate, or change the sirius subscription. Set button – to set the pushbutton memory when...

  • Page 289

    Ipod 姞 /usb/mp3 control — if equipped note: this section is for sales code res and req/ rel/ret radios only with uconnect™. For sales code rbz/rhb, rhr, rhp, rhw or rb2 touch-screen radio ipod 威 /usb/mp3 control feature, refer to the separate rbz/rhb, rhr, rhp, rhw or rb2 user’s manual. Ipod 威 /usb/...

  • Page 290

    Connecting the ipod 姞 or external usb device use the connection cable to connect an ipod 威 or external usb device to the vehicle’s usb/aux connector port which is located in the center console or glove compart- ment. Once the audio device is connected and synchronized to the vehicle’s ipod 威 /usb/mp...

  • Page 291

    • the audio device can be controlled using the radio buttons to play, browse, and list the ipod 威 contents. • the audio device battery charges when plugged into the usb/aux connector (if supported by the specific audio device) controlling the ipod 姞 or external usb device using radio buttons to get ...

  • Page 292

    • a single press backward rw or forward ff >> will jump backward or forward respectively, for five sec- onds. • use the seek and seek >> buttons to jump to the previous or next track. Pressing the seek >> button during play mode will jump to the next track in the list, or press the vr button and say...

  • Page 293

    List or browse mode during play mode, pressing any of the buttons described below, will bring up list mode. List mode enables scrolling through the list of menus and tracks on the audio device. • tune control knob: the tune control knob functions in a similar manner as the scroll wheel on the audio ...

  • Page 294

    • to exit list mode without selecting a track, press the same preset button again to go back to play mode . • list button: the list button will display the top level menu of the ipod 威 or external usb device. Turn the tune control knob to list the top-menu item to be selected and press the tune cont...

  • Page 295

    Bluetooth streaming audio (btsa) music can be streamed from your cellular phone to the uconnect™ phone system. Controlling btsa using radio buttons to get into the btsa mode, press either “aux” button on the radio or press the vr button and say “bluetooth streaming audio”. Play mode when switched to...

  • Page 296

    Browse browsing is not available on a btsa device. Only the current song that is playing will display info. Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a...

  • Page 297

    Pressing the center button will make the radio switch between the various modes available (am/fm/sat/ cd/hdd/aux/ves, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The follo...

  • Page 298

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 299

    Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. Manual heating and air conditioning the manual temperature controls consist of a series of outer rotary dials and inner push knobs. Blower control rotate this control to regulate the...

  • Page 300

    Temperature control rotate this control to regulate the tem- perature of the air inside the passenger compartment. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures. Note: if your air conditionin...

  • Page 301

    Bi-level air is directed through the panel and floor outlets. Note: for all settings, except full cold or full hot, there is a difference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets. This feature gives improved comfort during sunny but cool condition...

  • Page 302

    Recirculation control pressing the recirculation control button will put the system in recirculation mode. This can be used when outside conditions such as smoke, odors, dust, or high humidity are pres- ent. Activating recirculation will cause the led in the control button to illuminate. Note: • con...

  • Page 303

    Note: the air conditioning compressor will not engage until the engine has been running for about 10 seconds. • max a/c for maximum cooling use the a/c and recirculation buttons at the same time. • economy mode if economy mode is desired, press the a/c button to turn off the indicator light and the ...

  • Page 304

    Note: the auto position performs best for front seat occupants only. Dial in the temperature you would like the system to maintain by rotating the temperature control knob. Once the comfort level is selected, the sys- tem will maintain that level automati- cally using the heating system. Should the ...

  • Page 305

    Blower control for full automatic operation or for automatic blower operation, turn the knob to the auto position. In manual mode there are seven blower speeds that can be individual selected. In off position the blower will shut off. Manual operation this system offers a full complement of manual o...

  • Page 306

    304 understanding your instrument panel.

  • Page 307

    The operator can override the auto mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • panel air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. Note: the center ...

  • Page 308

    • air conditioner control press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the mode control dial. Press this but- ton a second time to turn off the air conditionin...

  • Page 309

    • most of the time, when in automatic operation, you can temporarily put the system into recirculation mode by pressing the recirculation button. However, under certain conditions, while in automatic mode, the system is blowing air out the defrost vents. When these conditions are present, and the re...

  • Page 310

    Adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window fogging interior fogging on the windshield can be quickly re- moved by turning the mode selector to defrost. The defrost/floor mode can be used to maintain a clear windshield and pro...

  • Page 311

    Control setting suggestions for various weather conditions 4 understanding your instrument panel 309.

  • Page 313: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .315 ▫ manual transmission – if equipped . . . . . . . .315 ▫ automatic transmission – if equipped . . . . . .316 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .316 ▫ extreme cold weather (below –20°f ...

  • Page 314

    䡵 autostick 威 . . . . . . . . . . . . . . . . . . . . . . . . .329 ▫ continuously variable automatic transmission (cvt) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .329 䡵 four-wheel drive operation — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .331 䡵 on-road driving...

  • Page 315

    䡵 tires — general information. . . . . . . . .359 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .359 ▫ tire inflation pressures . . . . . . . . . . . . . . . . .360 ▫ tire pressures for high speed operation . . . .362 ▫ radial ply tires . . . . . . . . . . . . . . . . . . . . . .362 ...

  • Page 316

    ▫ reformulated gasoline . . . . . . . . . . . . . . . . .382 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . .382 ▫ e-85 usage in non-flex fuel vehicles . . . . . . .383 ▫ mmt in gasoline . . . . . . . . . . . . . . . . . . . . .383 ▫ materials added to fuel . . . . . . . . . . . . . . . .384 ...

  • Page 317

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the ...

  • Page 318

    Automatic transmission – if equipped the shift lever must be in the park or neutral position before you can start the engine. Apply the brakes before shifting to any driving gear. Note: you must press the brake pedal before shifting out of park. Tip start do not press the accelerator. Turn the ignit...

  • Page 319

    Warning! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a d...

  • Page 320

    Caution! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Engine block heater — if equipped the engine block ...

  • Page 321

    Fully press the clutch pedal before you shift gears. As you release the clutch pedal, lightly press the accelerator pedal. Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can re...

  • Page 322

    Recommended shift speeds to use your manual transmission for optimal fuel economy, it should be upshifted as listed in the following table. Manual transmission recommended shift speeds units in mph (km/h) engine size accel- era- tion rate 1 to 2 2 to 3 3 to 4 4 to 5 all en- gines accel 14 (23) 23 (3...

  • Page 323

    Automatic transmission — if equipped caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to a complete stop. • shift into or out of reverse only after the vehicle has come to a complete stop and the engine i...

  • Page 324

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the ignition key in or near...

  • Page 325

    Continuously variable automatic transmission (cvt) the shift lever position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of park (refer to “brake/transmission shift interlock system” in this section). To...

  • Page 326

    Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park this range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use...

  • Page 327

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to mo...

  • Page 328

    Warning! (continued) • when leaving the vehicle, always remove the igni- tion key and lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could b...

  • Page 329

    • with brake pedal released, verify that the shift lever will not move out of park. Reverse this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral use this range when the vehicle is standing for prolonged periods with the engine ...

  • Page 330

    Drive this range should be used for most city and highway driving. It provides the best fuel economy. The drive position provides optimum driving characteristics under all normal operating conditions. When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading ...

  • Page 331

    Autostick 姞 continuously variable automatic transmission (cvt) autostick 威 is a driver-interactive transmission feature providing six manually selectable gear ratios, giving you more control of the vehicle. Autostick 威 allows you to maximize engine braking, eliminate undesirable upshifts and downshi...

  • Page 332

    • the transmission will automatically upshift when nec- essary to prevent engine over-speed. • if a downshift would cause the engine to overspeed, that shift will not occur until it is safe for the engine. • transmission shifting will be more noticeable when autostick 威 is engaged. • heavy anti-lock...

  • Page 333

    Four-wheel drive operation — if equipped this feature provides full time, on-demand, four–wheel drive (4wd). Where one or more wheels have wheel spin or if addi- tional traction is needed in sand, deep snow, or loose traction surfaces, activate the “4wd lock” switch by pulling up once and releasing....

  • Page 334

    An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfacto- rily in off-road cond...

  • Page 335

    Warning! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature an...

  • Page 336

    If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further informa- tion. Parking brake before leaving the vehicle, make sure that the parki...

  • Page 337

    Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • this light only shows that ...

  • Page 338

    Warning! (continued) • always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic trans- mission in park, a manual transmission in re- verse or first gear. Failure to do so may cause the vehicle to roll and cause...

  • Page 339

    If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfuncti...

  • Page 340

    Warning! (continued) • the abs cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • the capabilities of an abs-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize th...

  • Page 341

    Working properly. This self-check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h). Abs is activated during braking under certain road or stopping conditions. Abs-inducing conditions can in- clude ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops. Yo...

  • Page 342

    (tcs), brake assist system (bas), electronic roll mitiga- tion (erm), hill descent control (hdc), hill start assist (hsa), and electronic stability control (esc). All sys- tems work together to enhance vehicle stability and control in various driving conditions and are commonly referred to as esc. A...

  • Page 343

    Quickly results in the best bas assistance. To receive the benefit of the system, you must apply continuous brak- ing pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the bas is...

  • Page 344

    Prevent wheel lift due to other factors such as road conditions, leaving the roadway or striking objects or other vehicles. Note: anytime the esc system is in the “full off” mode, erm is disabled. Refer to “electronic stability control (esc)” in this section for a complete explanation of the availab...

  • Page 345

    Off” button for five seconds. Refer to “electronic stability control (esc)” in this section of the manual. Hdc operation can be overridden with brake application to slow the vehicle down below the hdc control speed. Conversely, if more speed is desired during hdc control, the accelerator pedal will ...

  • Page 346

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 7% grade or greater hill. • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphill is in rever...

  • Page 347

    5. Release the clutch pedal (if equipped). 6. Rotate the steering wheel one-half turn to the left. 7. Press the “esc off” switch (located in the lower switch bank below the climate controls) four times within 20 seconds. The “esc activation/malfunction indicator light” should turn on and turn off tw...

  • Page 348

    Warning! • the electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • esc cannot prevent accidents, including those re- sulting from excessive speed in turns, driving on ve...

  • Page 349

    In deep snow, sand or gravel conditions and more wheel spin than esc would normally allow is required to gain traction. To turn esc on again, momentarily press the “esc off” switch. This will restore the normal “esc on” mode of operation. Note: to improve the vehicle’s traction when driving with sno...

  • Page 350

    “esc off” message will appear in the odometer. Press and release the trip odometer button located on the instrument cluster to clear this message. In this mode, esc and tcs, except for the “limited slip” feature described in the tcs section, are turned off until the vehicle reaches a speed of 35 mph...

  • Page 351

    Esc activation/malfunction indicator light and esc off indicator light the “esc activation/malfunction indicator light” in the instrument cluster will come on when the ignition switch is turned to the on position. It should go out with the engine running. If the “esc activation/malfunction indicator...

  • Page 352

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 353

    Compact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Ex- ample: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 r15 lt. Tire sizing chart...

  • Page 354

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 355

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 356

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 357

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Tire and loading information placard this placard tells you important information about the: ...

  • Page 358

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 359

    2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and pas- sengers from xxx lbs or xxx kg. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amou...

  • Page 360

    358 starting and operating.

  • Page 361

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 362

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns t...

  • Page 363

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” cold tire infl...

  • Page 364

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and ...

  • Page 365

    The tire sidewall. Use all season tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Summer or three season tires – if equipped summer tires provide traction in both wet and dry conditions, and are not intended to be driven in snow or on ice. S...

  • Page 366

    Spare tire matching original equipped tire and wheel – if equipped your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for y...

  • Page 367

    Since this tire has limited tread life the original equip- ment tire should be repaired (or replaced) and reinstalled on your vehicle at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically fo...

  • Page 368

    Your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than ...

  • Page 369

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is wo...

  • Page 370

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 371

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 372

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation a...

  • Page 373

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (6.9 kpa) for every 12°f (6.5°c). This means that when the ...

  • Page 374

    Driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressur...

  • Page 375

    Note: • the tpms is not intended to replace normal tire care and maintenance or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat a...

  • Page 376

    • four tire pressure monitoring sensors • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster, a low tire message will be displayed for a minimum of five seconds, and an audible...

  • Page 377

    5. Using wheels/tires not equipped with tpm sensors. Note: your vehicle is equipped with a compact spare wheel and tire assembly. 1. The compact spare tire does not have a tire pressure monitoring sensor. Therefore, the tpms will not moni- tor the tire pressure in the compact spare tire. 2. If you i...

  • Page 378

    Premium system – if equipped the tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure lev- els. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is particularly important for you to ...

  • Page 379

    Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible and inflate all tires that are flashing on the graphic display to the vehicle’s recommended cold placard pres- sure value. The system will automatically update, the “low tire” text message w...

  • Page 380

    Service tpms message the tire pressure monitoring telltale light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime. The evic will display a “service tpm sys- tem” message for a minimum of five seconds. This text messag...

  • Page 381

    If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the tire pressure monitoring telltale light will no longer flash, the ⬙ service tpm system ⬙ text message will not be present, and a pressure value will be display...

  • Page 382

    2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warn- ing limit, upon the next ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will still turn on due to the low tire. The “low tire” text message and th...

  • Page 383

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 384

    Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the world- wide fuel charter, wwfc) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recom- mends the use of gasolines...

  • Page 385

    E-85 usage in non-flex fuel vehicles non-ffv vehicles are compatible with gasoline contain- ing 10% ethanol (e10). Gasoline with higher ethanol content may void the vehicle’s warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • ...

  • Page 386

    Can be used at levels higher than those allowed in the united states. Mmt is prohibited in federal and califor- nia reformulated gasoline. Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or other additi...

  • Page 387

    Note: intentional tampering with the emissions control system can result in civil penalties being assessed against you. Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: (continued) warning! (continue...

  • Page 388

    Adding fuel fuel filler cap (gas cap) the gas cap is behind the fuel filler door, on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. After removing the gas cap, place the gas cap tether cable over a hook on the inside of the ...

  • Page 389

    Caution! • damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. • a poorly fitting gas cap may cause the “malfunc- tion indicator light (mil)” to turn on. • to avoid fu...

  • Page 390

    Loose fuel filler cap message if the vehicle diagnostic system determines that the fuel filler cap is loose or improperly installed, a “gascap” message will be displayed in the odometer/trip odom- eter in the instrument cluster. Refer to “instrument cluster description” in “understanding your instru...

  • Page 391

    Gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the gvwr. Tire size the tire size on the vehicle certification label represents the actual tire size on you...

  • Page 392

    Overloading can cause potential safety hazards and shorten useful service life. Heavier suspension compo- nents do not necessarily increase the vehicle’s gvwr. Loading to load your vehicle properly, first figure out its empty weight. Store heavier items down low and be sure you distribute their weig...

  • Page 393

    Exceed the gvwr. Refer to “vehicle loading/vehicle certification label” in “starting and operating” for further information. Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer ...

  • Page 394

    Than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal area the frontal area is the maximum height multiplied by the maximum width of the front of a trailer. Trailer sway control the trailer sway control is a telescoping link that can be in...

  • Page 395

    And trailer configuration / loading to comply with gross axle weight rating (gawr) requirements. Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability, braking performance, and could result in a collision. • weight distributing systems may not be compat- i...

  • Page 396

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/transmission frontal area maximum gtw (gross trailer wt.) maximum tongue wt. (see note) 2.0l auto/man 22 sq ft (2.04 sq m) 1,000 lbs (450 ...

  • Page 397

    Which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions. Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of t...

  • Page 398

    Towing requirements to promote proper break-in of your vehicle drivetrain components, the following guidelines are recommended: caution! • do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • then, during the f...

  • Page 399

    Warning! (continued) • safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • vehicles with trailers should not be parke...

  • Page 400

    • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation procedures. • check the trailer tires for proper tire inflation pres- sures before trailer usage. • c...

  • Page 401

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Warning! • do not connect trailer brake...

  • Page 402

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 403

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Manual transmission – if equipped if using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippag...

  • Page 404

    Extended driving at high rpm should be avoided to prevent excess heat generation. A reduction in vehicle speed may be required to avoid extended driving at high rpm. Return to a higher gear or vehicle speed when grade and road conditions allow. Electronic speed control – if equipped • do not use in ...

  • Page 405

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none • transmission in neutral • key in acc position not allowed dolly tow front ok (fwd only) ok (fwd only) rear not all...

  • Page 406

    Note: vehicles equipped with manual transmissions may be recreationally towed (flat towed) at any legal highway speed, for any distance, if the manual transmis- sion is in neutral and the ignition key is in the acc position. Caution! • do not flat tow any vehicle equipped with an automatic transmiss...

  • Page 407: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .406 䡵 if your engine overheats . . . . . . . . . . . .406 䡵 jacking and tire changing . . . . . . . . . .408 ▫ jack location . . . . . . . . . . . . . . . . . . . . . . . .408 ▫ spare tire stowage . . . . . . . . . . ....

  • Page 408

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel, below the radio. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Press th...

  • Page 409

    • you can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling system could damage ...

  • Page 410

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 411

    Spare tire stowage the compact spare tire is stowed under the rear load floor in the cargo area. Spare tire removal lift up the load floor cover and remove the hold down. Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to ...

  • Page 412

    6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle while the vehicle is being jacked. Jacking instructions warning! Carefully follow these ...

  • Page 413

    Warning! (continued) • only use the jack in the positions indicated and for lifting this vehicle during a tire change. • if working on or near a roadway, be extremely careful of motor traffic. • to assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve s...

  • Page 414

    Note: the jack handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place. 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is s...

  • Page 415

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated. Jacking locations front jacking location 6 what to do in emergencies 413.

  • Page 416

    Do not raise the vehicle until you are sure the jack is securely engaged. 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 417

    5. Remove the wheel nuts and pull the wheel and wheel covers, where applicable, off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the whee...

  • Page 418

    Note: the wheel cover is held on the wheel by the wheel nuts. When reinstalling the original wheel, prop- erly align the wheel cover to the valve stem, place the wheel cover onto the wheel, then install the wheel nuts. 6. Lower the vehicle by turning the jack screw to the left. 7. Finish tightening ...

  • Page 419

    Road tire installation vehicles equipped with wheel covers 1. Mount the road tire on the axle. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand. Do not use a hammer or excessive force to install the cover. Tire and wheel cover or center cap 1 — ...

  • Page 420

    3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in pe...

  • Page 421

    3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. The correct tight- ness of...

  • Page 422

    Preparations for jump-start the battery in your vehicle is located in the front of the engine compartment below the air intake duct. To access the battery remove the air intake duct by turning the two finger screws, located on the radiator support. Air intake finger screws positive battery post 420 ...

  • Page 423

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 424

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Note: remove air intake before proceeding with this jump-starting procedure. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the...

  • Page 425

    Once the engine is started, remove the jumper cables in the reverse sequence: 6. Disconnect the negative (-) jumper cable from the engine ground of the vehicle with the discharged battery. 7. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. 8. Di...

  • Page 426

    Caution! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the en- gine to idle with the shift lever in neutral for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure du...

  • Page 427

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 428

    6. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever forward. 7. Move the shift lever to the neutral position. 8. The vehicle may then be started in neutral. 9. Reinstall the shift lever override access cover. Towing a disabled vehicle this sec...

  • Page 429

    With ignition key automatic transmission • front wheel drive (fwd) vehicles can be towed with the front wheels elevated or on a flatbed truck (all four wheels off the ground). • four-wheel drive (4wd) vehicles must be towed on a flatbed truck (all four wheels off the ground). Caution! • do not flat ...

  • Page 430

    All transmissions if you must use the accessories (wipers, defroster, etc.) while being towed, the key must be in the on/run position, not the acc position. Make certain the trans- mission remains in neutral. If the battery is discharged, see “shift lever override” in “what to do in emergencies” for...

  • Page 431: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 2.0l . . . . . . . . . .431 䡵 engine compartment — 2.4l . . . . . . . . . .432 䡵 onboard diagnostic system — obd ii . .433 ▫ loose fuel filler cap message . . . . . . . . . . . .433 䡵 emissions inspection and maintenance programs . . . . . . ....

  • Page 432

    ▫ automatic transmission – if equipped . . . . . .455 ▫ manual transmission – if equipped . . . . . . . .457 ▫ rear drive assembly (rda) – awd/4wd models only . . . . . . . . . . . . . . .458 ▫ power transfer unit (ptu) – awd/4wd models only . . . . . . . . . . . . . . .458 ▫ appearance care and pro...

  • Page 433

    Engine compartment — 2.0l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 7 maintaining your vehicle 43...

  • Page 434

    Engine compartment — 2.4l 1 — washer fluid reservoir 6 — air cleaner filter 2 — power steering fluid reservoir 7 — coolant pressure cap 3 — engine oil fill 8 — engine oil dipstick 4 — brake fluid reservoir 9 — engine coolant reservoir 5 — integrated power module (fuses) 432 maintaining your vehicle.

  • Page 435

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 436

    Persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the mil. Resolving the problem will turn the mil light off. Emissions inspection and maintenance programs in some localities, ...

  • Page 437

    4. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 438

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 439

    Caution! • failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle perfor- mance. Immediately have potential malfunctions examined by an authorized dealer or qualified repai...

  • Page 440

    Will result in the oil level at the full end of the indicator range. Caution! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Also, be sure the oil fill cap is replac...

  • Page 441

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity (sae grade) sae 5w-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperatu...

  • Page 442

    Station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine oil filter the engine oil filter should be replaced with a new filter at every engine oil change. Engine oil filter selection this manufacturer’s engines have a full-flow ...

  • Page 443

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 444

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 445

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 446

    Hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of...

  • Page 447

    In cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exer...

  • Page 448

    Warning! (continued) • a hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your ve- hicle in areas where your exhaust system can con- tact anything that can burn. ...

  • Page 449

    Note: intentional tampering with emissions control systems can result in civil penalties being assessed against you. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn ...

  • Page 450

    Coolant checks check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh engine coolant (anti- freeze). Chec...

  • Page 451

    Selection of coolant refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decr...

  • Page 452

    Period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze). When adding engine coolant (antifreeze): • the manufacturer recommends using mop...

  • Page 453

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 454

    The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for the coolant freeze point or replacing the engine coolant (antifreeze). Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bot...

  • Page 455

    • make sure that the coolant expansion bottle overflow hoses are not kinked or obstructed. • keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • do not change the thermostat for summer or winter operation. If replacement i...

  • Page 456

    When the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Note: if your vehicle is equipped with a manual trans- mission , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in...

  • Page 457

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 458

    Only the manufacturer’s recommended transmission fluid which has the special friction coefficient additives necessary for proper steel belt traction on the drive and driven pulleys. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further informa- tion. It is import...

  • Page 459

    Routine fluid level checks are not required, therefore the transmission has no dipstick. Your authorized dealer can check your transmission fluid level using special service tools. If you notice fluid leakage or transmission malfunc- tion, visit you authorized dealer immediately to have the fluid le...

  • Page 460

    Note: if contaminated with water, the fluid should be changed immediately. Rear drive assembly (rda) – awd/4wd models only lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further informa...

  • Page 461

    Frequency of fluid change refer to the “maintenance schedule” for the proper maintenance intervals. Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads p...

  • Page 462

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar 威 car wash or equiva- lent, or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar 威 super kleen b...

  • Page 463

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as...

  • Page 464

    Stain repel fabric cleaning procedure – if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by blotting with a clean, dry towel. • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar 威 total clean or equival...

  • Page 465

    Solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather condi- tioner is not required to maintain the original condition. Warning! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they m...

  • Page 466

    When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Instrument panel cover the instrument panel cover has a low glare surface which minimizes reflections on the windshield. Do not use protectants or other products whi...

  • Page 467

    Replace the belts if they appear frayed or worn or if the buckles do not work properly. Fuses integrated power module the integrated power module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini-fuses. A label that identifies each comp...

  • Page 468

    Cav- ity cartridge fuse mini- fuse description 3 10 amp red rear center brake light switch 4 10 amp red ignition switch/ occupant classifica- tion module 5 20 amp yellow trailer tow – if equipped 6 10 amp red power mirror/ steering control satel- lite radio/hands-free phone 7 30 amp green ignition o...

  • Page 469

    Cav- ity cartridge fuse mini- fuse description 16 15 amp lt blue dome lamp/ sunroof/rear wiper motor 17 10 amp red wireless control mod- ule 18 40 amp green auto shutdown relay 19 20 amp yellow radio amplifiers 20 15 amp lt blue radio 21 10 amp red intrusion module/ siren – if equipped 22 10 amp red...

  • Page 470

    Cav- ity cartridge fuse mini- fuse description 30 20 amp yellow heated seat – if equipped 31 10 amp red headlamp washer – if equipped 32 30 amp pink auto shutdown relay 33 10 amp red j1962 conn/ powertrain control module 34 30 amp pink antilock brakevalve 35 40 amp green antilock brake pump cav- ity...

  • Page 471

    Caution! (continued) • when replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it indicates a problem in ...

  • Page 472

    Exterior bulbs bulb number low beam headlamp h11 high beam headlamp 9005 front park/turn signal lamp 7444na front side marker lamp 194 front fog lamp h11 center high mounted stop lamp (chmsl) led assembly (serviced at authorized dealer) rear tail/stop lamp led assembly (serviced at authorized dealer...

  • Page 473

    Fog lamps 1. Access lamp through the lower fascia cutout. 2. Remove electrical connector from bulb. 3. Remove bulb from housing. Rear turn signal and backup lamp 1. Remove the two push-pins from the taillamp housing. 2. Grasp the taillamp and pull firmly to disengage the lamp from the aperture panel...

  • Page 474

    License lamps 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate. 2. Rotate the socket 1/4 turn counterclockwise. 3. Pull bulb from socket. Center high-mounted stoplamp this light is an led assembly. See your authorized dealer for replacement. F...

  • Page 475

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar 威 antifreeze/coolant 10 year/150,000 mile for- mula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standard ms-12106. Engine oil use api certifi...

  • Page 476

    Chassis component fluid, lubricant, or genuine part automatic transmission (cvt) – if equipped mopar 威 cvtf+4 威 continuously variable transmission fluid manual transmission – if equipped mopar 威 atf+4 威 automatic transmission fluid or equivalent licensed atf+4 威 product. Rear drive assembly (rda) mo...

  • Page 477: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .476 ▫ maintenance chart. . . . . . . . . . . . . . . . . . . . .478 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 478

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 479

    Note: under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km) or twelve months, whichever comes first. Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire inflation pressures and look for unusual wear or dam...

  • Page 480

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 481

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 482

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 483

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 484

    ** the spark plug change interval is mileage based only, yearly intervals do not apply. Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a servi...

  • Page 485: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .485 ▫ prepare for the appointment. . . . . . . . . . . . .485 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .485 ▫ be reasonable with requests ....

  • Page 486

    䡵 department of transportation uniform tire quality grades . . . . . . . . .491 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .491 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .492 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .492 484 if you need consum...

  • Page 487

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 488

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 489

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 490

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 491

    Mopar 姞 parts mopar 威 fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your ve...

  • Page 492

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 493

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 494

    Traction grades the traction grades, from highest to lowest, are aa, a, b, and c. These grades represent the tire’s ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked c may have poor traction perfor- m...

  • Page 495

    Compass chrysler group llc o w n e r ’ s m a n u a l 2013 c ompas s 13mk49-126-aa first edition printed in u.S.A. 2 0 1 3.

  • Page 496

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 497: Index

    Index 10

  • Page 498

    Abs (anti-lock brake system) . . . . . . . . . . . . . . . .337 adding engine coolant (antifreeze) . . . . . . . . . . . .449 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .386 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .444 additives, fuel . . . . . . . . . ...

  • Page 499

    Fluid level check . . . . . . . . . . . . . . . . . . . . . .456 fluid type . . . . . . . . . . . . . . . . . . . . . . . . . . .455 gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . .323 special additives . . . . . . . . . . . . . . . . . . . . . . .456 autostick . . . . . . . . . . . ....

  • Page 500

    Cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197 cargo load floor . . . . . . . . . . . . . . . . . . . . . . . . .200 cargo tie-downs . . . . . . . . . . . . . . . . . . . . . . . . .200 car washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .460 cellular phone ....

  • Page 501

    Disposal of used coolant . . . . . . . . . . . . . . . . .451 drain, flush, and refill . . . . . . . . . . . . . . . . . .448 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 points to remember . . . . . . . . . . . . . . . . . . . . .452 pressure cap . . . . . . . . . . . . . ....

  • Page 502

    Electronic stability control (esc) . . . . . . . . . . . . . .345 electronic vehicle information center (evic) . . . . . .228 emergency, in case of jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .408 jump starting . . . . . . . . . . . . . . . . . . . . . . . . .419 towing . . . ....

  • Page 503

    Flooded engine starting . . . . . . . . . . . . . . . . . . . .317 fluid, brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .474 fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . . .472 fluid leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 fluid level ch...

  • Page 504

    Gasoline (fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . .381 gasoline, reformulated . . . . . . . . . . . . . . . . . . . . .382 gauges coolant temperature . . . . . . . . . . . . . . . . . . . .217 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212 odometer . . . . ...

  • Page 505

    Ignition key removal . . . . . . . . . . . . . . . . . . . . . . .12 immobilizer (sentry key) . . . . . . . . . . . . . . . . . . . .15 infant restraint . . . . . . . . . . . . . . . . . . . . . . . . . . .76 information center, vehicle . . . . . . . . . . . . . . . . . .228 inside rearview mirror ....

  • Page 506

    Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 anti-lock . . . . . . . . . . . . . . . . . . . . . . . . . . . .214 back-up . . ....

  • Page 507

    Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . .390 tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .355 locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 automatic door . . . . . . . . . . . . . . . . . . . . . . . .31 child protection...

  • Page 508

    Mtbe/etbe . . . . . . . . . . . . . . . . . . . . . . . . . . . .382 multi-function control lever . . . . . . . . . . . . . . . . .162 new vehicle break-in period . . . . . . . . . . . . . . . . . .96 occupant restraints . . . . . . . . . . . . . . . . . . . . . . . .39 occupant restraints (sedan) ....

  • Page 509

    Pets, transporting. . . . . . . . . . . . . . . . . . . . . . . . . .95 phone, cellular . . . . . . . . . . . . . . . . . . . . . . . . . . .112 phone, hands-free (uconnect™). . . . . . . . . . . . . . .112 placard, tire and loading information . . . . . . . . . .355 power door locks . . . . . . . ....

  • Page 510

    Reminder, seat belt. . . . . . . . . . . . . . . . . . . . . . . . .59 remote control door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 security alarm . . . . . . . . . . . . . . . . . . . . . . . . .18 remote keyless entry (sedan) . . . . . . . . . . . . . . . . .20 remote sound ...

  • Page 511

    Front seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . .55 rear seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 untwisting procedure...

  • Page 512

    Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 starting procedures . . . . . . . . . . . . . . . . . . . . . . . .315 steering power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .332 tilt column . . . . . . . . . . . . . . . . . . . . . . . . . . .171 steering ...

  • Page 513

    Pressure monitor system (tpms) . . . . . . . . . . .371 pressure warning light . . . . . . . . . . . . . . . . . .219 quality grading . . . . . . . . . . . . . . . . . . . . . . .491 radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .362 replacement . . . . . . . . . . . . . . . . ....

  • Page 514

    Transmitter battery service (remote keyless entry) . .25 transmitter, garage door opener (homelink 威 ) . . . .176 tread wear indicators . . . . . . . . . . . . . . . . . . . . . .367 trip computer . . . . . . . . . . . . . . . . . . . . . . . . . . .226 trip odometer . . . . . . . . . . . . . . . . ...

  • Page 515

    Window fogging . . . . . . . . . . . . . . . . . . . . . . . . .308 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 windshield defroster . . . . . . . . . . . . . . . . . . . . . . .99 windshield washers ...

  • Page 516

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 517

    Patriot 2 0 1 3.