1. DL manuals
  2. Jeep
  3. Automobile
  4. WRANGLER 2017
  5. Owner's Manual

Jeep WRANGLER 2017 Owner's Manual

Other manuals for WRANGLER 2017: Quick Reference Manual, User Manual

Summary of WRANGLER 2017

  • Page 1

    Wrangler o w n e r ’ s m a n u a l 2 0 1 7.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 graphical table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 rollover warning . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . . .5 ▫ essential information . . . . . . . . . . . . . . . . . . . . . .5 ▫ symbols . . . . . . . ....

  • Page 6

    Introduction congratulations on selecting your new fca us llc ve- hicle. Be assured that it represents precision workmanship, distinctive styling, and high quality. The two-wheel drive version of this vehicle was designed for on-road use only. It is not intended for off-road driving or use in other ...

  • Page 7

    Higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not. Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle con- trol. Failure to operate this vehicle safely may result in a collision, ro...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may mi...

  • Page 11: Contents

    Graphical table of contents contents 䡵 front view . . . . . . . . . . . . . . . . . . . . . . . . . . .10 䡵 rear view. . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 䡵 instrument panel . . . . . . . . . . . . . . . . . . . . .12 䡵 interior . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 12

    Front view front view 1 — doors 2 — exterior mirrors 3 — wheels/tires 4 — windshield 5 — hood/engine compartment 6 — headlights 10 graphical table of contents.

  • Page 13

    Rear view rear view 1 — rear lights 2 — rear windshield wiper — if equipped 3 — swing gate 2 graphical table of contents 11.

  • Page 14

    Instrument panel instrument panel 1 — air outlet 7 — power outlet 2 — instrument cluster 8 — climate controls 3 — radio 9 — lower switch bank 4 — power window switches 10 — power mirror switch — if equipped 5 — assist handle 11 — horn 6 — glove compartment 12 graphical table of contents.

  • Page 15

    Interior interior features 1 — seats 2 — power window switches 3 — radio 4 — climate controls 5 — switch panel 6 — transmission gear selector 2 graphical table of contents 13.

  • Page 17: Contents

    Getting to know your vehicle contents 䡵 key fobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 䡵 ignition switch . . . . . . . . . . . . . . . . . . . . . . .21 ▫ ignition key removal . . . . . . . . . . . . . . . ...

  • Page 18

    䡵 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 ▫ manual front seats . . . . . . . . . . . . . . . . . . . . . .37 ▫ manual rear seats . . . . . . . . . . . . . . . . . . . . . . .41 ▫ heated seats — if equipped . . . . . . . . . . . . . . .45 䡵 head restraints . . . . . . ...

  • Page 19

    ▫ windshield washers. . . . . . . . . . . . . . . . . . . . . .58 ▫ mist feature . . . . . . . . . . . . . . . . . . . . . . . . . . .58 ▫ rear window wiper/washer — if equipped . . . .59 䡵 climate controls . . . . . . . . . . . . . . . . . . . . .60 ▫ manual climate control overview . . . . . . . ....

  • Page 20

    ▫ lowering the soft top . . . . . . . . . . . . . . . . . . .110 ▫ raising the soft top. . . . . . . . . . . . . . . . . . . . .119 䡵 sunrider (two-door models) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 ▫ opening the sunrider . . . . . . . . . . . . . . . . . . .128 ▫ ...

  • Page 21

    Key fobs your vehicle uses a key start ignition system. The ignition system consists of a remote keyless entry (rke) key fob with an ignition switch. Key fob the key fob allows you to lock or unlock the doors and liftgate from distances up to approximately 66 ft (20 m) using a handheld key fob. The ...

  • Page 22

    To lock the doors and swing gate push and release the lock button on the key fob to lock all doors. The turn signals will flash, and the horn will chirp once to acknowledge the lock signal. Key fob battery replacement the recommended replacement battery is cr2032. Note: perchlorate material – specia...

  • Page 23

    Refer to “sentry key” in “getting to know your vehicle” for further information. General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss...

  • Page 24

    Warning! • before exiting a vehicle, always shift the automatic transmission into park or the manual transmission into first gear or reverse, apply the parking brake, turn the engine off, remove the key fob from the vehicle and lock your vehicle. • never leave children alone in a vehicle, or with ac...

  • Page 25

    • hazard switch off • brake switch inactive (brake pedal not pushed) • ignition key removed from ignition • battery at an acceptable charge level • panic button not pushed • system not disabled from previous remote start event • vehicle security alarm not active warning! • do not start or run an eng...

  • Page 26

    • the engine can be started two consecutive times (two 15-minute cycles) with the key fob. However, the igni- tion switch must be cycled to the on/run position before you can repeat the start sequence for a third cycle. Remote start will also cancel if any of the following occur: • the engine stalls...

  • Page 27

    Sentry key the sentry key immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses key fobs that have an embedded electroni...

  • Page 28

    Duplication of key fobs may be performed at an authorized dealer or by following the customer key programming procedure. This procedure consists of programming a blank key fob to the vehicle electronics. A blank key fob is one that has never been programmed. Note: when having the sentry key immobili...

  • Page 29

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 30

    Arming period, opening any door or the swing gate will cancel the arming. If the vehicle security alarm is success- fully set, the vehicle security light will flash at a slower rate to indicate the vehicle security alarm is armed. To disarm the system to disarm the vehicle security alarm, you will n...

  • Page 31

    Manual door locks all doors are equipped with an interior rocker-type door lock lever. To lock a door when leaving your vehicle, push the rocker lever forward to the lock position and close the door. To unlock the door, push the rocker lever rearward. Note: the ignition key that is used to start the...

  • Page 32

    Warning! (continued) • when leaving the vehicle, always remove the key from the ignition and lock your vehicle. Unsuper- vised use of vehicle equipment may cause severe personal injuries and death. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children ...

  • Page 33

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking b...

  • Page 34

    Upper half door window removal — if equipped grasp the half door window and pull upward. Upper half door window installation — if equipped 1. Grasp the half door window and line up the pins with the pockets in the lower door. 2. Push down to ensure the half door window is fully seated. Front door re...

  • Page 35

    1. Roll down the glass window to prevent any damage. 2. Remove the hinge pin screws from the upper and lower outside hinges (using a #t50 torx head driver). Note: the hinge pin screws and nuts can be stowed in the rear cargo tray located under the rear loadfloor. 3. Unplug the wiring harness connect...

  • Page 36

    Note: doors are heavy; use caution when removing them. To reinstall the door(s), perform the previous steps in the opposite order. Rear door removal (four-door models) warning! Do not drive your vehicle on public roads with the doors removed as you will lose the protection that they can provide. Thi...

  • Page 37

    3. Slide the front seat(s) fully forward. 4. Remove the trim access door from the bottom of the b-pillar. 5. Unplug the wiring harness connector. Note: squeeze the tab on the base of the connector. This will unlock the connector tab, allowing the harness to be disconnected. Hinge pin screw trim acce...

  • Page 38

    6. Unhook the door strap from the body hook. 7. With the door open, lift the door to clear the hinge pins from their hinges and remove the door. Note: doors are heavy; use caution when removing them. To reinstall the door(s), perform the previous steps in the opposite order. Connector latched connec...

  • Page 39

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 40

    Warning! (continued) • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. Manual seat height adjustment — if equipped the driver’s seat height can be raised or lowered by using the ratchetin...

  • Page 41

    Front passenger easy entry seat — two-door models pull upward on the recline lever (toward the rear of the vehicle) and slide the entire seat forward. To return the seat to a sitting position, rotate the seatback upright until it locks and push the seat rearward until the track locks. Note: • the fr...

  • Page 42

    Tip n’ slide seats — two-door models this feature allows the front seats to be rotated toward the instrument panel to allow easier entry into the rear seats. Driver’s seat pull upward on the recline lever and bring the seatback to its full forward position. Rotate the entire seat assembly toward the...

  • Page 43

    Passenger seat in addition to easy entry, the front passenger seat is also equipped with tip n’ slide. This feature allows for easier entry for rear passengers. Pull upward on the recline lever and slide the entire seat forward (easy entry). With the seat forward, pull the entire seat assembly towar...

  • Page 44

    1. Lift the seatback release lever and fold the seatback forward. 2. Slowly flip the entire seat forward. Warning! Do not drive the vehicle with the seat in the forward tumble position. The seat must be latched to all floor attachments when the vehicle is in motion. 3. Push down on the release bar o...

  • Page 45

    Warning! • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be...

  • Page 46

    Note: • prior to folding the rear seat, it may be necessary to reposition the front seat to its mid-track position. • be sure that the front seats are fully upright and posi- tioned forward. This will allow the rear seat to fold down easily. Warning! • it is extremely dangerous to ride in a cargo ar...

  • Page 47

    Note: if the rear seatback is not fully latched, the center shoulder belt will not be able to be extended for use. If you cannot extend the center shoulder belt, make sure your seatback is fully latched. Warning! Be certain that the seatback is securely locked into position. If the seatback is not s...

  • Page 48

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 49

    Warning! • a loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow re- moved head restraints in a location outside the occupant compartment. (continued) warning! (continued) • all the head restraints must...

  • Page 50

    Warning! • do not drive the vehicle without the rear seat head restraints installed while passengers are occupying the rear seat. In a collision, people riding in this area without the head restraints installed are more likely to be seriously injured or killed. • a loose head restraint thrown forwar...

  • Page 51

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Mirrors inside day/night ...

  • Page 52

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activat...

  • Page 53

    Warning! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distan...

  • Page 54

    Vanity mirrors vanity mirrors are located on the sun visors. To use the mirrors, rotate the sun visor down and swing the mirror cover upward. Exterior lights headlights and parking lights turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second dete...

  • Page 55

    High/low beam switch push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam. Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the multifunction lever towar...

  • Page 56

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: • if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside...

  • Page 57

    In the multifunction lever. These lights are also controlled automatically by the illuminated entry system. A courtesy light is also found in the rear of the center console. You can turn this light on and off from the dimmer control in the multifunction lever. This light is also con- trolled automat...

  • Page 58

    Switch on the multifunction lever fully upward, or if equipped, when the unlock button is pushed on the remote keyless entry key fob. The sports bar reading lights (available on four-door models) can be turned on by pushing the switches, located on either side of the lens. Push a switch a second tim...

  • Page 59

    Lever. For information on using the rear window wiper/ washer, refer to “rear window wiper/washer” in this section for more information. Windshield wiper operation rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end o...

  • Page 60

    Intermittent wiper system use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Rotate the end of the lever to the first detent position for one of five intermittent settings. The delay cycle can be set anywhere between 1 to 1...

  • Page 61

    Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Rear window wiper/washer — if equipped a rotary switch on the center portion of the control lever...

  • Page 62

    Rotate the switch upward to the first detent position for rear wiper operation. Rotate the switch upward past the first detent to activate the rear washer. The washer pump and the wiper will continue to operate as long as the switch is held. Upon release, the wiper will cycle two to three times befo...

  • Page 63

    Manual climate control descriptions icon description a/c button push the a/c button to engage the air conditioning (a/c). An led will illuminate when the a/c system is engaged. Recirculation button push and release this button to change the system between recirculation mode and outside air mode. Rec...

  • Page 64

    Icon description rear defrost button push and release the rear defrost control button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window de- froster is on. The rear window defroster automatically turns off after 10 min...

  • Page 65

    Icon description bi-level mode bi-level mode air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Note: bi-level mode is designed under comfort conditions to provide cooler air out of the panel outlets...

  • Page 66

    Automatic climate control overview automatic climate control descriptions icon description a/c button push the a/c button to engage the air conditioning (a/c). An led will illuminate when the a/c system is engaged. Automatic temperature controls 64 getting to know your vehicle.

  • Page 67

    Icon description automatic operation the automatic temperature control system automatically maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. Operation of the system is quite simple. Turn the mode control knob (on the right) and the blower c...

  • Page 68

    Icon description temperature control use this control to regulate the temperature of the air inside the passenger compartment. Rotat- ing the knob counterclockwise, from top center into the blue area of the scale, indicates cooler temperatures. Rotating the knob clockwise, into the red area, indicat...

  • Page 69

    Icon description bi-level mode bi-level mode air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Note: bi-level mode is designed under comfort conditions to provide cooler air out of the panel outlets...

  • Page 70

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear win- dow. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heat- ing eleme...

  • Page 71

    Window fogging vehicle windows tend to fog on the inside in mild, rainy and/or humid weather. To clear the windows, select de- frost or mix mode and increase the front blower speed. Do not use the recirculation mode without a/c for long periods, as fogging may occur. Outside air intake make sure the...

  • Page 72

    Operating tips chart power windows — if equipped the power window switches are located on the instrument panel below the radio. Push the switch downward to open the window and upward to close the window. The top left switch controls the left front window and the top right switch controls the right f...

  • Page 73

    Warning! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, or in a location accessible to children. Occupants, particularly unat- tended children, can become entrapped by the win- dows while operating the p...

  • Page 74

    Dual top — two-door models — if equipped please visit http://www.Jeep.Com/en/wrangler-rooftop- instructions/ for instructional videos. If your vehicle is equipped with a dual top, you must remove one of the tops from the vehicle. If the soft top is removed, the pivot brackets must also be removed fr...

  • Page 75

    Note: to aid in disconnecting the knuckles, you may carefully tap on the knuckles using a rubber mallet. 5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #t30 torx head driver. Recover and re-zip the sports bar cover. Store the pivot brackets and s...

  • Page 76

    4. If the soft top has been removed, follow these steps to reinstall the soft top. If the soft top is on the vehicle, proceed to step #5. A. If the pivot brackets have been removed, unzip the sport bar covers and attach the pivot brackets to the sports bar with the four screws that were removed usin...

  • Page 77

    Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 5. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside. Note: be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top. 6. U...

  • Page 78

    Removing the soft top — four-door models 1. Locate and remove the two boxes that contain the following items: • right and left door frames • six door frame attachment knobs • right and left quarter windows • rear window • two rear window roll up straps • two sunrider secure straps (if equipped) • tw...

  • Page 79

    5. The tether strap must be hooked onto the pivot bracket prior to removal of soft top from vehicle (both sides). 6. Remove the soft top bow assembly pivot bracket bolts (two per side) from the sport bar using a 10.0 mm wrench or socket driver. 7. Lift the soft top in a upward motion to release the ...

  • Page 80

    8. Remove the soft top from the vehicle and store in a clean, dry location (another person may be needed to help with this operation). Note: if you are doing this alone, use one arm to hold the bundle up, the other to remove the brackets. 9. Reinstall the hard top. Refer to “freedom top three- piece...

  • Page 81

    Installing the soft top — four-door models note: the following procedures are for first time set up only. For future soft top procedures, refer to “soft top” in this section. 1. Locate and remove the following items prior to hard top removal: • right and left door frames • six door frame attachment ...

  • Page 82

    6. Install the pivot bracket bolts back into place using a 10.0 mm wrench or socket driver. Secure them until they are snug, being careful not to cross-thread the screws or overtighten. Caution! Do not overtighten the screws. You can strip the screws if they are overtightened. 7. Remove the tether s...

  • Page 83

    8. Using the plastic reinforcement as a handle remove the tether strap from the bracket hook by sliding strap up off hook and slide down the side bow (both sides). 9. Button the side bow tether strap (both sides). 10. Remove the swing gate bar (black metal bar for bottom of rear window) and set asid...

  • Page 84

    12. Put up the soft top. Refer to “soft top — putting up the soft top” in this section. Freedom top three-piece modular hard top — if equipped caution! • the hard top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or lugga...

  • Page 85

    3. Turn the center l-shaped locks (two) from the center of the roof panel. 4. Turn the rear l-shaped lock (located above the shoulder belt anchorage). Step two step three 3 getting to know your vehicle 83.

  • Page 86

    5. Unlatch the header panel latch located at the top of the windshield. 6. Remove the left-hand panel. To remove the right panel, follow the steps above except for step 3. Step four step five 84 getting to know your vehicle.

  • Page 87

    Freedom top storage bag vehicles equipped with a freedom top modular hard top, come with a freedom top storage bag that allows you to store your freedom top panels. The storage bag contains two compartments and fits behind the rear seat. Lay the freedom bag down so the loops and hooks are facing dow...

  • Page 88

    2. Unfold the black panel divider (ensure the divider is laying flat). Secure the velcro, located at the center of the divider. 3. Insert the left-side freedom panel into the bag with the latches facing upward. Note: ensure the front freedom panel latch is closed prior to inserting the panel into th...

  • Page 89

    4. Unfold the outer flap and zip the freedom bag closed. 5. Install the seat attachment strap (at the top of the bag) through the loops. Step four step five 3 getting to know your vehicle 87.

  • Page 90

    6. Lift the freedom bag into the vehicle with the hooks and straps facing the back of the rear seat. Attach the clips at the bottom of the bag to the child restraint anchorages, located at the base of the rear seat. 7. Wrap the upper strap around the rear head restraints and loop the strap through t...

  • Page 91

    Front panel(s) installation with rear hard top removed 1. Turn the left and right panels over and move the spacer block (located on the rear of the panel) upward 90 degrees. Note: the front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there i...

  • Page 92

    5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass. 6. Locate the wire harness on the left rear inside corner of the vehicle. Step five wire harness connector 90 getting to know your vehicle.

  • Page 93

    7. Release the red locking tab by pulling outward to the right. 8. To remove the wiring harness push the tab and pull downward to disconnect. 9. To remove the washer hose, pinch the grips on hose connector and pull downward. Red locking tab push tab to disconnect 3 getting to know your vehicle 91.

  • Page 94

    10. Close the swing gate. 11. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage. Caution! The removal of the freedom top requires four adults located on each corner. Failure to follow this caution could damage the freedom top. Rear hard top installation not...

  • Page 95

    Door frame warning! • do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only. • do not drive your vehicle on public roads with the doors removed as you will los...

  • Page 96

    3. Pull the frame toward you with your rearward hand to remove the frame from the vehicle. 4. Screw the knobs back into the door frame and fold for storage. Store in a secure location. Warning! • do not drive your vehicle on public roads with the door frame(s) removed as you will lose the protection...

  • Page 97

    Door frame installation — two-door models — if equipped 1. Unfold door frame and unscrew thumbscrews. 2. Set the door frame pin into the hole on top of the body side, behind the door opening. 3. After the door frame pin has been set into the body side hole, carefully set the front of the door frame ...

  • Page 98

    5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side. Door frame installation — four-door models — if equipped 1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening. 3. Position t...

  • Page 99

    4. Loosely install the rear knob (long knob) to hold the door rail in position. 5. Carefully set the front of the front door frame in the rubber seal at the top of the windshield. 6. Clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched...

  • Page 100

    8. Loosely install both knobs beginning with the front knob (long knob). Then, install the middle knob (short knob) through the front and rear door frames and screw into the top of the b-pillar. 9. Tighten the front knob, then the rear most knob, and then the middle knob. Repeat this procedure for t...

  • Page 101

    Soft top — two-door models please visit http://www.Jeep.Com/en/wrangler-rooftop- instructions/ for instructional videos. Warning! • do not drive the vehicle with the rear window curtain up unless the side curtains are also removed. Dangerous exhaust gases could enter the vehicle causing harm to the ...

  • Page 102

    Caution! • do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. • do not lower the top when the temperature is below 41°f (5°c). Damage to the top may result. • do not move your vehicle until the top has been either fully attached to the windshield fra...

  • Page 103

    Quick steps to lowering the soft top refer to “lowering the soft top” in this section for further information. 1. Remove the side windows. 2. Remove the back window. Step one step two 3 getting to know your vehicle 101.

  • Page 104

    3. Release header latches from the windshield frame. 4. Release the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. Step three step four 102 getting to know your vehicl...

  • Page 105

    5. Make sure the plastic sleeves are slid rearward over the sunrider link to lock in the link (sunrider models only). 6. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top. Step five step six 3 getting to know your vehicle 103.

  • Page 106

    7. Release the sunrider latch (both sides). 8. Open the swing gate and lower the top. Note: ensure fabric does not overhang the sides of the vehicle. Step seven step eight 104 getting to know your vehicle.

  • Page 107

    Quick steps to raising the soft top refer to “raising the soft top” in this section for further information. 1. Open the swing gate and raise the top, engaging the sunrider latches (another person may be needed to help with this operation). 2. Engage header latches. Step one step one 3 getting to kn...

  • Page 108

    3. Install rear corner panels. 4. Install the back window. Step two step three 106 getting to know your vehicle.

  • Page 109

    5. Install the side windows. 6. To install the side windows, affix the window tempo- rarily by attaching to the velcro in the rear corner. Start the zipper but close only about 1 inch (2.5 cm). 7. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated...

  • Page 110

    Step seven retainer insertion 1 — incorrect insertion 2 — correct insertion 108 getting to know your vehicle.

  • Page 111

    8. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro along the top and rear of the window. Repeat this step for the opposite side. Step ...

  • Page 112

    Lowering the soft top side view top and components 1 — 3–bow 6 — bottom retainer — quarter window 2 — 2–bow 7 — quarter window 3 — header bow 8 — sail panel 4 — front retainer — quarter window 9 — check strap 5 — body side retainer 110 getting to know your vehicle.

  • Page 113

    Rear view top and components 1 — sail panels 2 — zipper finish 3 — swing gate bar 4 — zipper start 5 — swing gate brackets 3 getting to know your vehicle 111.

  • Page 114

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 115

    5. Before unzipping the rear window, release the first 3 inches (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rear- ward out of the swing gate brackets. 6. Unzip the rear window starting at the right lower corner of the window. Pull the zipper up, ac...

  • Page 116

    8. Stow the windows carefully to avoid scratching. 9. Undo the velcro that runs along the top and rear edge of the side window. 10. Beginning from the rear lower corner, completely un- zip the window. 11. Once unzipped, remove the side window retainers from the door channel and body side channel. Re...

  • Page 117

    Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 13. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top. 14. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove th...

  • Page 118

    15. Completely release the latches from the loops on the windshield frame. If your vehicle is not equipped with the sunrider package, proceed to step 18. 16. Make sure the plastic sleeves are slid rearward over the sunrider link to lock in the link (sunrider models only). Step fourteen step fifteen ...

  • Page 119

    17. Unlatch the side bows from both door rails (sunrider models only). 18. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Move to the front of the vehicle. Grasp the side bow behind the header and lift the top, folding it toward t...

  • Page 120

    19. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle. 20. Close the front header latches. 21. Remove the door frames, if desired. Refer to “door frame” in this section for further informati...

  • Page 121

    Raising the soft top 1. Unclip and move the sun visors to the side. 2. Install door frames, if removed. Refer to “door frame” in this section for further information. 3. Make sure the plastic sleeve is slid over sunrider link (sunrider models only). 4. Standing on the side of the vehicle, lift the t...

  • Page 122

    6. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 7. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel u...

  • Page 123

    8. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow. 9. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to reac...

  • Page 124

    10. To install the side windows, affix the window tempo- rarily by attaching to the velcro in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 11. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on t...

  • Page 125

    12. Insert the retainer along the bottom edge of the win- dow into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro along the top and rear of the window. Repeat this step for the opposite side. St...

  • Page 126

    13. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. Step twelve step twelve 124 getting to know your vehicle.

  • Page 127

    14. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. Step thirteen step fourteen 3 getting to know your vehicle 125.

  • Page 128

    15. Run the zipper fully around to the right side of the window. 16. Grasp the swing gate bar and position it into the swing gate brackets. 17. Insert the rear window retainer into the swing gate bracket on both the left and right sides. Step fourteen step sixteen 126 getting to know your vehicle.

  • Page 129

    18. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel. 19. Close the header latches and return the sun visors to their secured position. Step seventeen step nineteen 3 getting to know your vehicle 1...

  • Page 130

    Sunrider (two-door models) — if equipped caution! Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. Note: if you are going to be driving faster than 40 mph (64 km/h) with the sunrider feature open, it is recom- mended tha...

  • Page 131

    4. Grasp the header and lift the top back. Make sure the material is folded back as shown. Note: the sunrider latch on the door rail should not be activated for sunrider use. If activated, the soft top must be reinstalled starting from the sail panels. 5. Locate the straps to secure the side bows. W...

  • Page 132

    6. Reposition the sun visors. Closing the sunrider 1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the front of the vehicle. 4. Hook the header latches to the loops on the windshield frame, close latches, and return the...

  • Page 133

    Caution! The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environme...

  • Page 134

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • it is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle...

  • Page 135

    Quick steps for lowering the soft top 1. Remove the side windows. 2. Remove the back window. Note: start zipper from the right side to remove back window. Step one step two 3 getting to know your vehicle 133.

  • Page 136

    3. Release header latches from the windshield frame. 4. Release the sail panel retainers from the body side channel at the rear corners of the vehicle. Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. Step three step four 134 getting to know your vehicl...

  • Page 137

    5. Fold the sail panels so that they rest on top of the soft top. 6. Fold header rearward, pulling the fabric to the rear. Step five step six 3 getting to know your vehicle 135.

  • Page 138

    7. Release sunrider latch (both sides). Step six step seven 136 getting to know your vehicle.

  • Page 139

    8. Open the swing gate and lower the top. Note: ensure the fabric does not overhang the sides of the vehicle. Quick steps for raising the soft top 1. Open the swing gate and raise the top, engaging the sunrider latches (another person may be needed to help with this operation). Step eight step one 3...

  • Page 140

    2. Install rear corner panels. Step one step two 138 getting to know your vehicle.

  • Page 141

    3. Rotate the header forward. 4. Engage the header latches. Step three step four 3 getting to know your vehicle 139.

  • Page 142

    5. Install the back window. 6. Install the side windows. Step five step six 140 getting to know your vehicle.

  • Page 143

    7. To install the side windows, affix the window tempo- rarily by attaching to the velcro in the rear corner. Start the zipper but close only about 1 in (2.5 cm). 8. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the...

  • Page 144

    9. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the velcro along the top and rear of the window. Repeat this step for the opposite side. Step ...

  • Page 145

    Folding down the soft top side view top and components 1 — 4– bow 6 — quarter window 2 — 3–bow 7 — body side retainer 3 — 2–bow 8 — bottom retainer — quarter window 4 — header bow 9 — sail panel 5 — front retainer — quarter window 10 — check strap 3 getting to know your vehicle 143.

  • Page 146

    Rear view top and components 1 — sail panels 2 — zipper finish 3 — swing gate bar 4 — zipper start 5 — swing gate brackets 144 getting to know your vehicle.

  • Page 147

    Note: clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. I...

  • Page 148

    6. Unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage it from the zipper on the top cover. 7. Remove the rear window retaine...

  • Page 149

    8. Stow the windows carefully to avoid scratching. 9. Undo the velcro that runs along the top and rear edge of the side window. 10. Beginning from the rear lower corner, completely un- zip the window. 11. Once unzipped, remove the side window retainers from the door channel and body side channel. Re...

  • Page 150

    Note: when releasing the sail panel retainers, it is helpful to pull down on the rear roof bow. 13. Fold the sail panels so that they rest on top of the soft top. Step twelve step thirteen 148 getting to know your vehicle.

  • Page 151

    14. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage. 15. Grasp the front side bow behind the header, and lift th...

  • Page 152

    16. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck. 17. Fold the top so that the material forms a ⬙ w ⬙ as shown. Enter the vehicle and move the material into two folds. Step sixteen step seventeen 150 getting to kno...

  • Page 153

    18. Release the side bows by pushing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side. 19. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Grasp the folded s...

  • Page 154

    21. Tuck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside of the vehicle. 22. Once the top is fully down, use the velcro straps provided to secure the top to the vehicle by wrapping the strap around the side bows ...

  • Page 155

    Putting up the soft top note: be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “door frame” in this section for further information. 2. Undo the straps used to sec...

  • Page 156

    6. Ensure that the top locks into the sunrider locking mechanisms that are located above the front of the rear doors. 7. Unclip and move the sun visors to the side. 8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame. Step five step six 154 get...

  • Page 157

    9. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches). 10. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel ...

  • Page 158

    11. Ensure that the straps are positioned correctly before pulling the sail panels over the rear roof bow (4–bow). Step ten step eleven 156 getting to know your vehicle.

  • Page 159

    Partially install the sail panel retainers into the body side channel, leaving the last 3 inches (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (4–bow) will aid in reaching the channel with the retainers. 12. To install the side windows, affix the window tem...

  • Page 160

    13. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window. 14. Insert the retainer along the bottom edge of the win- dow into the b...

  • Page 161

    15. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed. Step fourteen step fourteen 3 getting to know your vehicle 159.

  • Page 162

    16. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage. 17. Run the first zipper fully around to the right side of the window. Step fifteen step sixteen 16...

  • Page 163

    18. Grasp the swing gate bar and position it into the swing gate brackets. 19. Insert the rear window retainer into the swing gate bracket on both the left and right sides. 20. Complete the installation of the sail panel by inserting the rest of the retainer into the body channel. Step eighteen step...

  • Page 164

    21. Close the header latches and return the sun visors to their secured position. Sunrider (four-door models) — if equipped caution! Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. Note: if you are going to be driving f...

  • Page 165

    3. Make sure to slide the plastic sleeves forward to unlock the sunrider links. 4. Grasp the front side bow behind the header, and lift the top. Step three step four 3 getting to know your vehicle 163.

  • Page 166

    5. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 6. Fold the top so that the material forms a ⬙ w ⬙ as shown. Enter the vehicle and move the material into two folds. Step five step six 164 getting to know your vehicle.

  • Page 167

    7. Secure the top by using the two provided straps. Each strap will wrap around the side bow and velcro to itself; use one strap on each side of the vehicle. Closing the sunrider perform the above steps in the opposite order. Note: failure to fold the fabric rearward will allow the material to sag a...

  • Page 168

    Outside rearview mirrors are mounted on the doors. If you choose to remove the doors, see your authorized dealer for a replacement cowl-mounted outside mirror. Federal law requires outside mirrors on vehicles for on-road use. Warning! Carefully follow these warnings to help protect against personal ...

  • Page 169

    3. Remove the sun visor. 4. Remove the a-pillar cap. 5. Disconnect microphone (if equipped with uconnect phone). 6. Open the sport bar velcro covering. 7. Remove the one hex bolt (13 mm) visible through the plastic trim on the bottom side of the side bar, one hex bolt (13 mm) on the side of the side...

  • Page 170

    9. To safely store the side bars in your vehicle, use four cinch straps (available from your authorized dealer). Attach the straps through the slots located on the floor behind the folded rear seat at the front of the storage bin cover. Warning! You or others could be injured if you carry the side b...

  • Page 171

    Raising the windshield and replacing side bars 1. Raise the windshield. 2. Loosely attach the rear of the side bar to the sport bar. Refer to step 4 of “lowering windshield and removing side bars” earlier in this section. 3. Reattach the sport bar velcro covering. 4. Attach the front of the side bar...

  • Page 172

    8. Reinstall the wiper arms. Hood opening the hood release both the hood latches. Raise the hood and locate the safety latch, located in the middle of the hood opening. Push the safety latch to the left side of the vehicle, to open the hood. You may have to push down slightly on the hood before push...

  • Page 173

    Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. Rear swing gate the rear swing gate can be unlocked by ...

  • Page 174

    Caution! Do not push on rear wiper blade when closing the rear flip-up window, as damage to the blade will result. Internal equipment storage glove compartment the lockable glove compartment is located on the passen- ger side of the lower instrument panel. Pull outward on the handle/latch to open th...

  • Page 175

    There is an extra storage area underneath the console lid. The console lid has an integrated paper clip feature that can hold small items. Rear storage compartment — if equipped the rear cargo area storage compartment cover is held by a spring-loaded latch. In order to remove the rear storage compar...

  • Page 176

    Cupholders the front cupholders are located in the center console. The rear cupholders are located on the back of the center console. Electrical power outlets there are two 12 volt (13 amp) auxiliary power outlets that can provide power for accessories designed for use with the standard power outlet...

  • Page 177

    When the optional cigar lighter heating element is used in the power outlet, it heats when pushed in and pops out automatically when ready for use. To preserve the heating element, do not hold the lighter in the heating position. A second power outlet is located inside the center console and is powe...

  • Page 178

    Warning! To avoid serious injury or death: • do not insert any objects into the receptacles. • do not touch with wet hands. • close the lid when not in use. (continued) rear power outlet — if equipped power outlet fuse locations 1 — m36 fuse 20 a yellow power outlet console bin 2 — m6 fuse 20 a yell...

  • Page 179

    Warning! (continued) • if this outlet is mishandled, it may cause an electric shock and failure. Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery ...

  • Page 180

    The power inverter is designed with built-in overload protection. If the power rating of 150 watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet, the inverter should automatically reset. If the power rating exceeds approxima...

  • Page 181: Contents

    Getting to know your instrument panel contents 䡵 instrument cluster . . . . . . . . . . . . . . . . . .180 ▫ instrument cluster descriptions . . . . . . . . . . . .181 䡵 instrument cluster display — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183 ▫ instrument cluster display...

  • Page 182

    Instrument cluster instrument cluster 180 getting to know your instrument panel.

  • Page 183

    Instrument cluster descriptions 1. Fuel gauge • the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position. • the fuel pump symbol points to the side of the vehicle where the fuel filler door is located. 2. Speedometer • indicates vehicle speed. 3. Tachom...

  • Page 184

    5. Odometer / trip odometer display area • the odometer display shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “odometer/trip odometer/eco (fuel saver indicator) button” for further information. • u.S. Federal regulations require that ...

  • Page 185

    Instrument cluster display — if equipped your vehicle may be equipped with an instrument cluster display, which offers useful information to the driver. With the ignition in the stop/off mode, opening/closing of a door will activate the display for viewing, and display the total miles, or kilometers...

  • Page 186

    • digital speedometer • average fuel economy • distance to empty • tire pressure monitor system — if equipped • elapsed time • vehicle info • units selection • system status and warnings (door open, etc.) • personal settings (customer-programmable features) the system allows the driver to select inf...

  • Page 187

    • compass button push and release the compass button to return to the compass/outside temperature/audio information/eco screen whenever the current display is not the compass/ outside temperature/audio information/eco screen. • right arrow button push and release the right arrow button when prompted...

  • Page 188

    • check gascap (refer to “refueling the vehicle” in “starting and operating” for further information) • oil change required (with a single chime) • eco (fuel saver indicator) — if equipped gear shift indicator (gsi) — if equipped — up shift indicator light — down shift indicator light the gear shift...

  • Page 189

    3. Turn the ignition switch to the lock position. Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Instrument cluster display menu items note: the instrument cluster display menu items display i...

  • Page 190

    Manual compass calibration if the compass appears erratic and the “cal” indicator does not appear in the instrument cluster display, you must put the compass into the calibration mode manually as follows: 1. Start the engine. Leave the gear selector in park in order to enter the instrument cluster d...

  • Page 191

    To change the compass variance: 1. Turn the ignition switch run (it is not necessary to start the engine). 2. Push the menu button until personal settings (customer-programmable features) displays in the in- strument cluster display. 3. Push the down arrow button until “compass variance” message and...

  • Page 192

    Elapsed time shows the total elapsed time of travel since the last reset. Elapsed time will increment when the ignition switch is in the run or start position. Elapsed time displays minutes: seconds. After 59 minutes: 59 seconds have elapsed, hours will be displayed before minutes. Elapsed time can ...

  • Page 193

    Personal settings (customer-programmable features) personal settings allows the driver to set and recall features when the vehicle speed is at 0 mph (0 km/h) (manual transmission) or when the gear selector is in park (auto transmission). Push and release the menu button until personal settings displ...

  • Page 194

    Flash lamp with lock when on is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the key fob. This feature may be selected with or without the sound horn with lock feature selected. To make your selection, push and release the right arrow button until “...

  • Page 195

    Hill start assist (hsa) — if equipped when “on” is selected, the hsa system is active. Refer to “electronic brake control system” in “starting and oper- ating” for system function and operating information. To make your selection, push and release the right arrow button until “on” or “off” appears. ...

  • Page 196

    All active telltales will display first, if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Some tell- tales are optional and may not appear. The following warning lamps and indicators will alert you to a vehicle condition that may beco...

  • Page 197

    Battery charge warning light red telltale light what it means battery charge warning light this light illuminates when the battery is not charging properly. If it stays on while the engine is run- ning, there may be a malfunction with the charging system. Contact your authorized dealer as soon as po...

  • Page 198

    The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a s...

  • Page 199

    Coolant temperature warning light red telltale light what it means coolant temperature warning light this light warns of an overheated engine condition. If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into...

  • Page 200

    Electronic throttle control (etc) warning light red telltale light what it means electronic throttle control (etc) warning light this light informs you of a problem with the electronic throttle control (etc) system. If a prob- lem is detected while the vehicle is running, the light will either stay ...

  • Page 201

    Oil pressure warning light red telltale light what it means oil pressure warning light this light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehi...

  • Page 202

    Vehicle security warning light — if equipped red telltale light what it means vehicle security warning light — if equipped this light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. Yellow tel...

  • Page 203

    Anti-lock brake (abs) indicator light yellow telltale light what it means anti-lock brake (abs) indicator light this light monitors the anti-lock brake system (abs). The light will turn on when the ignition switch is placed in the on/run position and may stay on for as long as four seconds. If the a...

  • Page 204

    Yellow telltale light what it means light after vehicle start. The vehicle should be serviced if the light stays on through several typi- cal driving styles. In most situations, the vehicle will drive normally and will not require towing. When the vehicle is running, the mil may flash to alert serio...

  • Page 205

    Tire pressure monitoring system (tpms) warning light yellow telltale light what it means tire pressure monitoring system (tpms) warning light the warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss...

  • Page 206

    Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to main- tain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the tpms low tire pressure telltale. Your vehicle has also been equipped ...

  • Page 207

    Electronic stability control (esc) indicator light yellow telltale light what it means electronic stability control (esc) indicator light — if equipped the “esc indicator light” in the instrument cluster will come on when the ignition is placed in the on/run position. It should go out when the engin...

  • Page 208

    Electronic stability control (esc) off indicator light — if equipped yellow telltale light what it means electronic stability control (esc) off indicator light — if equipped this light indicates the electronic stability control (esc) is off. Front axle lock indicator light — if equipped yellow tellt...

  • Page 209

    4wd indicator light — if equipped yellow telltale light what it means 4wd indicator light this light alerts the driver that the vehicle is in the four-wheel drive mode, and the front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. ...

  • Page 210

    Turn signal indicator lights green telltale light what it means turn signal indicator lights the left or right arrow will flash with the corresponding exterior turn signal lights when the turn signal lever is operated. A chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either...

  • Page 211

    Hill descent control (hdc) indicator light — if equipped white telltale light what it means hill descent control (hdc) indicator light this indicator shows when the hill descent control (hdc) feature is turned on. The lamp will be on solid when hdc is armed. Hdc can only be armed when the transfer c...

  • Page 212

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic trans- mission control systems. When these systems are operating properly, your vehicle will provide ...

  • Page 213

    For further information, refer to “privacy practices” and “uconnect cybersecurity” in “all about uconnect access” in your owner’s manual radio supplement and “cyber- security” in “multimedia”. Loose fuel filler cap message after fuel is added, the vehicle diagnostic system can determine if the fuel ...

  • Page 214

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the igni- tion or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/...

  • Page 215: Safety

    Safety contents 䡵 safety features . . . . . . . . . . . . . . . . . . . . . .214 ▫ anti-lock brake system (abs) . . . . . . . . . . . . .214 ▫ electronic brake control system . . . . . . . . . . . .215 䡵 auxiliary driving systems . . . . . . . . . . . . .227 ▫ tire pressure monitor system (tpms) . ....

  • Page 216

    Safety features anti-lock brake system (abs) the anti-lock brake system (abs) provides increased vehicle stability and brake performance under most brak- ing conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking. The abs performs a self-check cycle to ...

  • Page 217

    Warning! (continued) • the capabilities of an abs equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user’s safety or the safety of others. Abs is designed to function with the oem tires. Modifica- tion may result in degraded abs performance. Anti-lo...

  • Page 218

    Brake system warning light the red “brake system warning light” will turn on when the ignition is turned to the on/run mode and may stay on for as long as four seconds. If the “brake system warning light” remains on or comes on while driving, it indicates that the brake system is not functioning pro...

  • Page 219

    The following conditions must be met in order for hsa to activate: • the feature must be enabled. • the vehicle must be stopped. • park brake must be off. • driver door must be closed. • the vehicle must be on a sufficient grade. • the gear selection must match vehicle uphill direction (i.E., vehicl...

  • Page 220

    For vehicles not equipped with an instrument cluster display, perform the following steps: 1. Center the steering wheel (front wheels pointing straight forward). 2. Shift the transmission into park. 3. Apply the parking brake. 4. Start the engine. 5. Rotate the steering wheel slightly more than one-...

  • Page 221

    The intended path, esc applies the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition. • oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • understeer - when the vehicle is turning less than appropriate for th...

  • Page 222

    The esc system has three available operating modes in 4h range. The system has one operating mode in 4l range. Two-wheel drive vehicles and four-wheel drive vehicles in 2h range have two operating modes. 4h range (4wd models) esc on this is the normal operating mode for esc in 4h range. Esc partial ...

  • Page 223

    Esc full off this mode is entered by pushing and holding the esc off switch for five seconds. In the ⬙ esc full off ⬙ mode, the engine torque reduction and stability features are disabled. Therefore, the enhanced vehicle stability offered by esc is unavailable. In an emergency evasive maneuver, the ...

  • Page 224

    Esc and tcs, except for the brake limited differential (bld) feature described in the tcs section, are turned off until the vehicle reaches an approximate speed of 40 mph (64 km/h). For speeds at or exceeding approximately 40 mph (64 km/h) the esc goes into ⬙ esc partial off ⬙ when the vehicle speed...

  • Page 225

    Note: to improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it may be desirable to switch to the ⬙ esc partial off ⬙ mode by pushing the ⬙ esc full off ⬙ switch. Once the situation requiring esc to be switched to the ⬙ esc partial off ⬙ mode ...

  • Page 226

    Note: • the “esc activation/malfunction indicator light” and the “esc off indicator light” come on momentarily each time the ignition is turned on. • each time the ignition is turned on, the esc system will be on even if it was turned off previously. • the esc system will make buzzing or clicking so...

  • Page 227

    Note: tsc cannot stop all trailers from swaying. Always use caution when towing a trailer and follow the trailer tongue weight recommendations. Refer to “trailer tow- ing” in “starting and operating” for further information. When tsc is functioning, the “esc activation/ malfunction indicator light” ...

  • Page 228

    Gear approximate hdc set speed drive 7.5 mph (12 km/h) reverse 1 mph (1.5 km/h) however, the driver can override hdc operation by applying the brake to slow the vehicle down below the hdc control speed. If more speed is desired during hdc control, the accelerator pedal will increase vehicle speed in...

  • Page 229

    Auxiliary driving systems tire pressure monitor system (tpms) the tire pressure monitoring system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (7.0 kpa) for every 12°f (6.5°c)....

  • Page 230

    The “tire pressure monitoring telltale light” will still be on. In this situation, the “tire pressure monitoring telltale light” will turn off only after the tires have been inflated to the vehicle’s recommended cold placard pressure value. Caution! • the tpms has been optimized for the original equ...

  • Page 231

    Monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is particularly important for you to check the tire pressure in all of your tires regularly and to maintain the proper pressure. The tire pressure ...

  • Page 232

    3. Lots of snow or ice around the wheels or wheel hous- ings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with tpm sensors. Vehicles not equipped with instrument cluster display will inform the driver which tire(s) are low but not provide actual tire pressure. The low tir...

  • Page 233

    “tire pressure monitoring telltale light” will turn off, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. Premium ...

  • Page 234

    • tire pressure monitoring telltale light a tire pressure monitoring sensor is located in the spare wheel, if the vehicle is equipped with a matching full-size spare wheel and tire assembly. The matching full-size spare tire can be used in place of any of the four road tires. Tire pressure monitorin...

  • Page 235

    Note: when filling warm tires, the tire pressure may need to be increased up to an additional 4 psi (30 kpa) above the recommended cold placard pressure in order to turn the tire pressure monitoring telltale light off. The vehicle may need to be driven for up to 10 minutes above 15 mph (24 km/h) to ...

  • Page 236

    Note: • if your vehicle is equipped with a matching full-size spare wheel and tire assembly, it has a tire pressure monitoring sensor, and can be monitored by the tire pressure monitoring system (tpms) when swapped with a low pressure road tire. In the event that the matching full-size spare tire is...

  • Page 237

    Tpms deactivation — if equipped the tpms can be deactivated if replacing all four wheel and tire assemblies (road tires) with wheel and tire assem- blies that do not have tpms sensors, such as when installing winter wheel and tire assemblies on your vehicle. To deactivate the tpms, first, replace al...

  • Page 238

    Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: occupant restraint systems features • seat belt systems • supplemental restraint systems (srs) air bags • child restraints some of the safety features described in this section may be sta...

  • Page 239

    Bags will inflate forcefully into the space between occu- pants and the door and occupants could be injured. 9. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, refer to the “cus- tomer assistance” section for customer service contact information. Warning!...

  • Page 240

    Seat belts are buckled. The outboard front passenger seat beltalert is not active when an outboard front passenger seat is unoccupied. Beltalert warning sequence the beltalert warning sequence is activated when the vehicle is moving above a specified vehicle speed range and the driver or outboard fr...

  • Page 241

    The seat belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoulder part of the seat belt to move freely with you under normal conditions. However, in a collision the seat belt will lock and reduce your risk of striking the inside of the vehicle or...

  • Page 242

    Warning! • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not protect you pro...

  • Page 243

    Equipped with a rear seat). Grasp the latch plate and pull out the seat belt. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Positi...

  • Page 244

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automatically ...

  • Page 245

    Warning! (continued) the retractor, immediately take the vehicle to your authorized dealer for service. Failure to follow this warning could result in serious injury or death. Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the ...

  • Page 246

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release button. To verify the shoulder belt anchorage is latched, pull downward on the should...

  • Page 247

    Seat belts and pregnant women seat belts must be worn by all occupants including preg- nant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong...

  • Page 248

    Switchable automatic locking retractor (alr) the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) which is used to secure a child restraint system. For additional information, refer to “installing child restraints using the vehicle seat b...

  • Page 249

    In automatic locking mode, the shoulder belt is automati- cally pre-locked. The seat belt will still retract to remove any slack in the shoulder belt. Use the automatic locking mode anytime a child restraint is installed in a seating position that has a seat belt with this feature. Children 12 years...

  • Page 250

    Supplemental restraint systems (srs) some of the safety features described in this section may be standard equipment on some models, or may be optional equipment on others. If you are not sure, ask your autho- rized dealer. The air bag system must be ready to protect you in a collision. The occupant...

  • Page 251

    The orc also includes diagnostics that will illuminate the instrument panel air bag warning light if a malfunction is detected that could affect the air bag system. The diagnos- tics also record the nature of the malfunction. While the air bag system is designed to be maintenance free, if any of the...

  • Page 252

    Warning! • being too close to the steering wheel or instrument panel during front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. (continued) warning! (continued)...

  • Page 253

    Driver or front passenger seat belt is buckled. The seat belt buckle switch may adjust the inflation rate of the ad- vanced front air bags. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the advanced front air bags ba...

  • Page 254

    When the orc detects a collision requiring the front air bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the front air bags. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air b...

  • Page 255

    When the sab deploys, it opens the seam on the outboard side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not se...

  • Page 256

    Sabs (if equipped with sabs) are a supplement to the seat belt restraint system. Sabs deploy in less time than it takes to blink your eyes. Warning! • occupants, including children, who are up against or very close to side air bags can be seriously injured or killed. Occupants, including children, s...

  • Page 257

    • front and side impact sensors • seat belt pretensioners • seat track position sensors • seat belt buckle switch if a deployment occurs the front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean som...

  • Page 258

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • after any collision, the vehicle should be taken to an authorized dealer immediately. Enhanced accident response system in the event of an impact, if the communication network remains inta...

  • Page 259

    Warning! (continued) • it is dangerous to try to repair any part of the air bag system yourself. Be sure to tell anyone who works on your vehicle that it has an air bag system. • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function proper...

  • Page 260

    Law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the edr. Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requi...

  • Page 261

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child re- straint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrie...

  • Page 262

    Child seats can be used either rear-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rear-facing direction than infant carriers do, so they can be used rear-facing by children who have outgrown their infant carrier but are still less than at le...

  • Page 263

    Warning! (continued) remove the child restraint before adjusting the ve- hicle seat position. When the vehicle seat has been adjusted, reinstall the child restraint. • when your child restraint is not in use, secure it in the vehicle with the seat belt or latch anchorages, or remove it from the vehi...

  • Page 264

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 265

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchorage system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch-equipped child seats. There ...

  • Page 266

    Frequently asked questions about installing child restraints with latch what is the weight limit (child’s weight + weight of the child re- straint) for using the latch anchor- age system to attach the child re- straint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the...

  • Page 267

    Frequently asked questions about installing child restraints with latch can the latch anchorages and the seat belt be used together to attach a rear-facing or forward-facing child restraint? No do not use the seat belt when you use the latch anchorage system to attach a rear-facing or forward-facing...

  • Page 268

    Frequently asked questions about installing child restraints with latch can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint ...

  • Page 269

    Locating the upper tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat, near the floor. Latch anchorages (four-door models) tether strap anchorages (two-door models) 5 safety 267.

  • Page 270

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear- facing child restraint...

  • Page 271

    Warning! (continued) child restraint system” for typical installation in- structions. Always follow the directions of the child restraint manu- facturer when installing your child restraint. Not all child restraint systems will be installed as described here. To install a latch-compatible child rest...

  • Page 272

    Unused belt could injure a child if they play with it and accidentally lock the seat belt retractor. Before installing a child restraint using the latch system, buckle the seat belt behind the child restraint and out of the child’s reach. If the buckled seat belt interferes with the child restraint ...

  • Page 273

    Description in “switchable automatic locking retractors (alr)” under “occupant restraint systems” for additional information on alr. Please see the table below and the following sections for more information. Lap/shoulder belt systems for installing child restraints in this vehicle automatic locking...

  • Page 274

    Frequently asked questions about installing child restraints with seat belts what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tethe...

  • Page 275

    1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its rear-most position to make...

  • Page 276

    Installing child restraints using the top tether anchorage warning! Do not attach a tether strap for a rear-facing car seat to any location in front of the car seat, including the seat frame or a tether anchorage. Only attach the tether strap of a rear-facing car seat to the tether anchorage that is...

  • Page 277

    3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • an incorrectly anchored tether strap could lead to increased head motion and possib...

  • Page 278

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be serious...

  • Page 279

    The passenger compartment. In addition, inspect the ex- haust system each time the vehicle is raised for lubrication or oil change. Replace as required. Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. D...

  • Page 280

    Warning! (continued) your floor mat to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control. To prevent serious injury or death: • always securely attach your floor mat using the floor mat fasteners. Do not install your floor mat upside down or turn your floor ...

  • Page 281

    Warning! (continued) • it is recommended to only use mild soap and water to clean your floor mats. After cleaning, always check your floor mat has been properly installed and is secured to your vehicle using the floor mat fasteners by lightly pulling mat. Periodic safety checks you should make outsi...

  • Page 283: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . . .283 ▫ manual transmission — if equipped . . . . . . . .283 ▫ automatic transmission — if equipped . . . . . .283 ▫ normal starting — gasoline engine . . . . . . . . .283 ▫ extreme cold weather (below –22°f or −30°...

  • Page 284

    䡵 power steering . . . . . . . . . . . . . . . . . . . . . .305 ▫ power steering fluid check . . . . . . . . . . . . . . .306 䡵 speed control — if equipped . . . . . . . . . .306 ▫ to activate . . . . . . . . . . . . . . . . . . . . . . . . . . .307 ▫ to set a desired speed. . . . . . . . . . . . . ...

  • Page 285

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • when leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to...

  • Page 286

    Cycle the ignition switch to the start position and release when the engine starts. If the engine fails to start within 10 seconds, cycle the ignition switch to the lock/off posi- tion, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Extreme cold weather (below –22°f or −30°c) to...

  • Page 287

    Released. If this occurs, continue cranking with the accel- erator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. If the engine shows no sign of starting after two 15-second periods of cranking with the accelerator pedal held to ...

  • Page 288

    Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration...

  • Page 289

    When the parking brake is applied with the ignition switch on, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the automatic transmission is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime ...

  • Page 290

    Warning! (continued) • always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic trans- mission in park, a manual transmission in re- verse or first gear. Failure to do so may cause the vehicle to roll and cause d...

  • Page 291

    Shifting fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal. You should always use first gear when starting from a standing position. Recommended vehicle shift speeds to utilize your manual transmission efficiently for both fuel e...

  • Page 292

    Caution! • skipping gears and downshifting into lower gears at higher vehicle speeds can damage the engine and clutch systems, any attempt to shift into lower gear with clutch pedal depressed may result damage to the clutch system. Shifting into lower gear and releasing the clutch may result in engi...

  • Page 293

    Reverse shifting to shift into reverse, bring the vehicle to a complete stop. Press the clutch and pause briefly to allow the gear train to stop rotating. Beginning from the neutral position, move the gear selector in one quick, smooth motion straight across and into the reverse area (the driver wil...

  • Page 294

    Warning! (continued) vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal. • unintended movement of a vehicle could injure...

  • Page 295

    Transmission out of park, the ignition must be turned to the on/run position (engine running or not) and the brake pedal must be pressed. Five-speed automatic transmission — if equipped the transmission gear position display (located in the instrument cluster) indicates the transmission gear range. ...

  • Page 296

    Note: • after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. • if there is a need to restart the engine, be sure to cycle the ignition to the lock/off position before restarting. Transmission gea...

  • Page 297

    Warning! (continued) foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal...

  • Page 298

    • look at the transmission gear position display and verify that it indicates the park position (p). • with brake pedal released, verify that the gear selector will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to ...

  • Page 299

    Transmission limp home mode transmission function is monitored electronically for ab- normal conditions. If a condition is detected that could result in transmission damage, transmission limp home mode is activated. In this mode, the transmission remains in the current gear until the vehicle is brou...

  • Page 300

    Vehicle. Autostick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and im- prove overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many ot...

  • Page 301

    To disengage autostick mode, hold the gear selector to the right (+) until ⬙ d ⬙ is once again displayed in the instrument cluster. You can shift in or out of the autostick mode at any time without taking your foot off the accelerator pedal. Warning! Do not downshift for additional engine braking on...

  • Page 302

    In the event that additional traction is required, the transfer case 4h and 4l positions can be used to lock the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed. The 4h and 4l positions are intended for loose, slippery road surfaces only and not int...

  • Page 303

    Shift positions for additional information on the appropriate use of each 4wd system mode position, see the information below: 2h position this range is used for normal street and highway driving on hard-surfaced roads. 4h position this range locks the front and rear driveshafts together, forcing th...

  • Page 304

    Transfer case will engage/disengage faster if you momen- tarily release the accelerator pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 4h to 4l or 4l to 4h with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission into neut...

  • Page 305

    Warning! On vehicles equipped with a limited-slip differential, never run the engine with one rear wheel off the ground. The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of your vehicle. Axle lock (tru–lok) — rubicon models the axle lock switch is lo...

  • Page 306

    This system is controlled by the sway bar switch located on the instrument panel (to the left of the steering column). Push the sway bar switch to activate the system. Push the switch again to deactivate the system. The “sway bar indicator light” (located in the instrument cluster) will illuminate w...

  • Page 307

    Note: the stabilizer/sway bar may be torque locked due to left and right suspension height differences. This condi- tion is due to driving surface differences or vehicle loading. In order for the stabilizer/sway bar to disconnect/ reconnect, the right and left halves of the bar must be aligned. This...

  • Page 308

    Caution! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Power steering fluid check checking the power steering fluid level at a define...

  • Page 309

    Note: in order to ensure proper operation, the speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the speed control system can be reactivated by pushing the speed control on/off button and resetting the desired vehic...

  • Page 310

    To set a desired speed turn the speed control on. When the vehicle has reached the desired speed, push the set (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. Note: the vehicle should be traveling at a steady speed and on level ground before pushin...

  • Page 311

    • if the button is continually pushed, the set speed will continue to decrease until the button is released, then the new set speed will be established. Metric speed (km/h) • pushing the set (-) button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a...

  • Page 312

    Warning! Speed control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control and have an accident. Do not use speed control in heavy traffic or on roads that are winding, icy, snow-covered or slippery. Refuel...

  • Page 313

    Caution! • damage to the fuel system or emission control sys- tem could result from using an improper fuel filler cap. A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “malfunction indicator light (mil)” to illuminate, due to fuel v...

  • Page 314

    Included on this label and indicates the month, day and hour of manufacture. The bar code that appears on the bottom of the label is your vin. Gross vehicle weight rating (gvwr) the gvwr is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo. The lab...

  • Page 315

    Loading the actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. The entire vehicle should first be weighed on a commercial scale to insure that the gvwr has not been exceeded. The weig...

  • Page 316

    Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load ...

  • Page 317

    Trailer sway control – if equipped the trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue. It typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer sway- ing motions while traveling...

  • Page 318

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 319

    Trailer towing weights (maximum trailer weight ratings) engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/manual 3.21 two–door sport model (4wd) 6,900 lbs (3 130 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907...

  • Page 320

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.21 two–door sahara model (4wd) 7,000 lbs (3 175 kg) 25 sq ft (2.32 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6l/ automatic 3.73 two–door ...

  • Page 321

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/manual 3.73 four–door sport model (4wd) 8,900 lbs (4 037 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (158 kg) 3.6l/ automatic 3.21 four–door ...

  • Page 322

    Engine/ transmission axle model gcwr (gross com- bined wt. Rating) frontal area max. Gtw (gross trailer wt.) max. Trailer tongue wt. (see note) 3.6l/ automatic 3.73 four–door sahara model (4wd) 9,000 lbs (4 082 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (158 kg) 3.6l/manual 4.10 four–door...

  • Page 323

    Trailer and tongue weight never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your...

  • Page 324

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible per- sonal injury. • an electronically actuated trailer brake controller is required when towing a trailer...

  • Page 325

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustration. Towing tips before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual tra...

  • Page 326

    Autostick — if equipped • when using the autostick shift control, select the high- est gear that allows for adequate performance and avoids frequent downshifts. For example, choose “4” if the desired speed can be maintained. Choose “3” or “2” if needed to maintain the desired speed. • to prevent exc...

  • Page 327

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground four-wheel drive models flat tow none see instructions • automatic transmission in park. • manual transmission in gear (not in neutral [n]). • transfer case in neutral (n). ...

  • Page 328

    Caution! (continued) damage. Tow with all four wheels either on the ground, or off the ground (using a vehicle trailer). • tow only in the forward direction. Towing this vehicle backwards can cause severe damage to the transfer case. • automatic transmissions must be placed in park for recreational ...

  • Page 329

    1. Bring the vehicle to a complete stop. 2. Press and hold the brake pedal. 3. Shift the automatic transmission into neutral or depress the clutch pedal on a manual transmission. 4. Turn the engine off. 5. Shift the transfer case lever into neutral (n). 6. Start the engine. 7. Shift the transmission...

  • Page 330

    6. Press and hold the brake pedal. 7. Shift the transmission into neutral. 8. Shift the transfer case lever to the desired position. Note: when shifting the transfer case out of neutral (n), the engine should remain off to avoid gear clash. 9. Shift the automatic transmission into park, or place man...

  • Page 331

    Off road driving tips side step removal — if equipped note: prior to off-road usage, the side steps should be removed to prevent damage if so equipped. 1. Remove the two nuts from the bodyside. 2. Remove one bolt from the underside of the vehicle. 3. Remove the side step assembly. The basics of off-...

  • Page 332

    Or braking. In most cases, there are no road signs, posted speed limits or signal lights. Therefore, you will need to use your own good judgment on what is safe and what is not. When on a trail, you should always be looking ahead for surface obstacles and changes in terrain. The key is to plan your ...

  • Page 333

    Lost. If you start to slow to a stop, try turning your steering wheel no more than a 1/4 turn quickly back and forth, while still applying throttle. This will allow the tires to get a fresh ⬙ bite ⬙ and help maintain your momentum. Caution! On icy or slippery roads, do not downshift at high engine r...

  • Page 334

    Crossing obstacles (rocks and other high points) while driving off-road, you will encounter many types of terrain. These varying types of terrain bring different types of obstacles. Before proceeding, review the path ahead to determine the correct approach and your ability to safely recover the vehi...

  • Page 335

    Large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover. If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires. Use the removed dirt to fill the rut ahead of the turnout you just created. You should...

  • Page 336

    Hill climbing hill climbing requires good judgment and a good under- standing of your abilities and your vehicle’s limitations. Hills can cause serious problems. Some are just too steep to climb and should not be attempted. You should always feel confident with the vehicle and your abilities. You sh...

  • Page 337

    Is there plenty of distance at the base of the hill to regain control if the vehicle descends to fast? If you feel confident in your ability to proceed, then make sure you are in 4l (low) and proceed with caution. Allow engine braking to control the descent and apply your brakes, if necessary, but d...

  • Page 338

    Driving through water extreme care should be taken crossing any type of water. Water crossings should be avoided, if possible, and only be attempted when necessary in a safe, responsible manner. You should only drive through areas which are designated and approved. You should tread lightly and avoid...

  • Page 339

    Vehicle will sink in, effectively increasing the water level on the vehicle. Be sure to consider this when determining the depth and the ability to safely cross. Crossing puddles, pools, flooded areas or other standing water puddles, pools, flooded or other standing water areas normally contain murk...

  • Page 340

    Always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • inspect the radiato...

  • Page 341: In Case Of Emergency

    In case of emergency contents 䡵 hazard warning flashers . . . . . . . . . . . .340 䡵 bulb replacement . . . . . . . . . . . . . . . . . . . .340 ▫ replacement bulbs . . . . . . . . . . . . . . . . . . . . .340 ▫ bulb replacement . . . . . . . . . . . . . . . . . . . . . .341 䡵 fuses . . . . . . . . ...

  • Page 342

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Push the switch to turn on the hazard warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. P...

  • Page 343

    Exterior bulbs bulb number headlamps (2) h13 front park/turn signal lamps (2) 3157na front side marker lamps (2) 168 fog lamps psx24w rear stop/tail/turn lamps (2) 3157 center high-mounted stop lamp l.E.D. Backup lamps (2) 3157 license lamp 194 note: numbers refer to commercial bulb types that can b...

  • Page 344

    6. Remove the lamp from the collar. 7. Grasp the bulb and turn 1/4 turn counterclockwise. 8. Pull the bulb from the housing. 9. Push connector locking tab to the unlock position. 10. Remove connector from bulb. 11. Push connector onto new bulb base, and push the connector locking tab to the lock pos...

  • Page 345

    Caution! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Rear tail, stop, turn signal, and backup lamp 1. Remove the two inboard screws attaching the tail light ho...

  • Page 346

    Fuses warning! • when replacing a blown fuse, always use an appro- priate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may re...

  • Page 347

    Totally integrated power module the totally integrated power module is located in the engine compartment near the battery. This center contains cartridge fuses, mini fuses, and relays. A label that identi- fies each component is printed on the inside of the cover. Cavity cartridge fuse mini fuse des...

  • Page 348

    Cavity cartridge fuse mini fuse description j9 40 amp green – pzev sec motor/flex fuel – if equipped j10 30 amp pink – headlamp wash relay/manifold tuning valve j11 30 amp pink – sway bar j12 – – – j13 60 amp yellow – ignition off draw (iod) – main j14 40 amp green – rear defroster j15 40 amp green ...

  • Page 349

    Cavity cartridge fuse mini fuse description m5 – 25 amp clear power inverter – if equipped m6 – 20 amp yellow power outlet #1/rain sensor m7 – 20 amp yellow power outlet #2 (batt/acc select) m8 – 20 amp yellow front heated seat m9 – 20 amp yellow rear heated seat – if equipped m10 – 15 amp blue igni...

  • Page 350

    Cavity cartridge fuse mini fuse description m15 – 20 amp yellow climate control system, rear view mirror, cabin compartment node, transfer case switch, multi-function control switch, tire pressure monitor, glow plug module – ex- port diesel only m16 – 10 amp red airbag module m17 – 15 amp blue left ...

  • Page 351

    Cavity cartridge fuse mini fuse description m30 – 15 amp blue wiper motor frt, j1962 diagnostic feed m31 – 20 amp yellow backup lamps m32 – 10 amp red airbag controller, tt europe m33 – 10 amp red powertrain controller m34 – 10 amp red park assist, climate control system, head- lamp wash, compass m3...

  • Page 352

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 353

    Note: turn the black plastic wing nut counterclockwise to loosen the jack from the storage bin. Spare tire removal to remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. Note: if you have added afterma...

  • Page 354

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. • block the ...

  • Page 355

    1. Remove the spare tire, jack and tools from the stored location. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 3. Assemble the jack and jacking tools. Connect the jack handle driver to the extension, then to the lug wr...

  • Page 356

    6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the lug nuts clockwise. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the ...

  • Page 357

    Nut has been tightened twice. For the correct lug nut torque refer to “torque specifications” in “technical specifications”. If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or service station. 5. After 25 miles (40 km) check the lug nut torqu...

  • Page 358

    1 — positive battery post 2 — negative battery post warning! • take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that co...

  • Page 359

    Jump-starting procedure warning! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Not...

  • Page 360

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the remote negative (-) post of the discharged vehicle. 2. Disconnect the opposite end of the negative (-) jumper cable from th...

  • Page 361

    Caution! (continued) (h), and you hear continuous chimes, turn the engine off immediately and call for service. Note: there are steps that you can take to slow down an impending overheat condition: • if your air conditioner (a/c) is on, turn it off. The a/c system adds heat to the engine cooling sys...

  • Page 362

    5. Press and maintain firm pressure on the brake pedal. 6. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever down. 7. Move the gear selector to the neutral position. 8. The vehicle may then be started in neutral. 9. Reinstall the gear selector ...

  • Page 363

    Note: push the ⬙ esc off ⬙ switch to place the electronic stability control (esc) system in ⬙ partial off ⬙ mode before rocking the vehicle. Refer to “electronic brake control system” in “safety” for further information. Once the vehicle has been freed, push the ⬙ esc off ⬙ switch again to restore ⬙...

  • Page 364

    Towing condition wheels off the ground 4wd models flat tow none see instructions under “recreational towing” in “starting and operating”. • automatic transmission in park • manual transmission in gear ( not in neu- tral) • transfer case in neutral • tow in forward direction wheel lift or dolly tow f...

  • Page 365

    Caution! (continued) • if the vehicle being towed requires steering, the ignition switch must be in the acc or on/run position, not in the lock/off position. Without the ignition key special care must be taken when the vehicle is towed with the ignition in the lock position. The only approved method...

  • Page 366

    Warning! • do not use a chain for freeing a stuck vehicle. Chains may break, causing serious injury or death. • stand clear of vehicles when pulling with tow hooks. Tow straps may become disengaged, causing serious injury. Caution! Tow hooks are for emergency use only, to rescue a vehicle stranded o...

  • Page 367: Servicing And Maintenance

    Servicing and maintenance contents 䡵 scheduled servicing . . . . . . . . . . . . . . . . .367 ▫ maintenance plan. . . . . . . . . . . . . . . . . . . . . . .368 ▫ heavy duty use of the vehicle . . . . . . . . . . . .372 䡵 engine compartment . . . . . . . . . . . . . . . . .373 ▫ engine compartment —...

  • Page 368

    ▫ spare tires — if equipped . . . . . . . . . . . . . . . .417 ▫ wheel and wheel trim care . . . . . . . . . . . . . .419 ▫ tire chains (traction devices) . . . . . . . . . . . . .420 ▫ tire rotation recommendations . . . . . . . . . . . .421 䡵 department of transportation uniform tire quality grade...

  • Page 369

    Scheduled servicing your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This ...

  • Page 370

    Once a month or before a long trip: • check engine oil level • check windshield washer fluid level • check the tire inflation pressures and look for unusual wear or damage • check the fluid levels of the coolant reservoir, brake master cylinder, power steering and automatic transmis- sion, and fill ...

  • Page 371

    Mileage or time passed (which- ever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208...

  • Page 372

    Mileage or time passed (which- ever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208...

  • Page 373

    Mileage or time passed (which- ever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208...

  • Page 374

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 375

    Engine compartment engine compartment — 3.6l 1 — integrated power module (fuses) 7 — washer fluid reservoir 2 — battery 8 — engine coolant reservoir 3 — engine oil dipstick 9 — air cleaner filter 4 — automatic transmission dipstick (under engine cover) 10 — coolant pressure cap 5 — engine oil fill 1...

  • Page 376

    Checking oil level to ensure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. The engine oil level should be checked five minutes after a warmed up engine has been shut off. Checking the oil while the vehicle is on level ground will improve the acc...

  • Page 377

    Warning! (continued) a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Refer to “jump-starting procedure” in “in case of emergency” for further information. • battery gas is flammable and explosive. Keep flame or sparks away...

  • Page 378

    Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. Engine oil change engine oil — gasolin...

  • Page 379

    The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the “engine compart- ment” illustration in this section. Note: mopar sae 5w-30 engine oil approved to fca material standard ms-6395 such as pennzoil,...

  • Page 380

    Note: be sure to follow the “severe duty conditions” maintenance interval if applicable. Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such remo...

  • Page 381

    2. Remove air hose and loosen clean air hose clamp then release the spring clips on the air intake cover. 3. Lift the air cleaner cover to access the air cleaner filter. Air cleaner filter cover 1 — spring clips 2 — air hose 3 — clean air hose clamp air cleaner air hose 1 — air filter cleaner cover ...

  • Page 382

    4. Remove the air cleaner filter element from the housing assembly. Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleane...

  • Page 383

    When inspecting accessory drive belts, small cracks that run across ribbed surface of belt from rib to rib, are considered normal. These are not a reason to replace belt. However, cracks running along a rib (not across) are not normal. Any belt with cracks running along a rib must be replaced. Also ...

  • Page 384

    Warning! • use only refrigerants and compressor lubricants ap- proved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flam- mable and can explode, injuring you. Other unap- proved refrigerants or lubricants can cause the sys- tem to fail, requiring costly repai...

  • Page 385

    Air conditioning filter replacement (a/c air filter) warning! Do not remove the cabin air filter while the vehicle is running, or while the ignition is in the acc or on/ run mode. With the cabin air filter removed and the blower operating, the blower can contact hands and may propel dirt and debris ...

  • Page 386

    5. Open the two air filter access doors. 6. Remove the two particulate air filters from the hvac air inlet housing. Pull the filter elements straight out of the housing, one at a time. 7. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. Ca...

  • Page 387

    8. Close a/c air filter access doors and secure retaining tabs. 9. Rotate the glove compartment door back into position. Refer to the “maintenance plan” for the proper mainte- nance intervals. Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot poi...

  • Page 388

    • hardening or cracking • deformation or fatigue if a wiper blade or wiper arm is damaged, replace the affected wiper arm or blade with a new unit. Do not attempt to repair a wiper arm or blade that is damaged. Wiper blade removal/installation caution! Do not allow the wiper arm to spring back again...

  • Page 389

    3. With the wiper blade disengaged, remove the wiper blade from the wiper arm. 4. Gently lower the wiper arm onto the glass. Wiper blade with release tab in unlocked position 1 — wiper blade 2 — wiper arm 3 — release tab wiper blade removed from wiper arm 1 — wiper blade 2 — wiper arm 3 — release ta...

  • Page 390

    Installing the front wipers 1. Lift the wiper arm off of the glass, until the wiper arm is in the full up position. 2. Position the wiper blade near the hook on the tip of the wiper arm. 3. Insert the hook on the tip of the arm through the opening in the wiper blade. 4. Slide the wiper blade up into...

  • Page 391

    2. To remove the wiper blade from the wiper arm, grasp the wiper blade nearest to wiper arm with your right hand. With your left hand hold the wiper arm as you pull the wiper blade away from the wiper arm past its stop far enough to unsnap the wiper blade pivot pin from the receptacle on the end of ...

  • Page 392

    3. Still grasping the wiper blade, move the wiper blade away from the wiper arm to disengage. Installing the rear wiper 1. Insert the wiper blade pivot pin into the opening on the end of the wiper arm. Grab the bottom end of the wiper arm with one hand, and apply pressure to the wiper blade flush wi...

  • Page 393

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips” in “safety” for further information. • a hot exhaust system can start a ...

  • Page 394

    To minimize the possibility of catalytic converter damage: • do not interrupt the ignition when the transmission is in gear and the vehicle is in motion. • do not try to start the vehicle by pushing or towing the vehicle. • do not idle the engine with any ignition components disconnected or removed,...

  • Page 395

    Gently spraying water from a garden hose vertically down the face of the a/c condenser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect...

  • Page 396

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 397

    Note: • some vehicles require special tools to add coolant prop- erly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system, please contact your local authorized dealer. • mixing engine coolant (antifreeze) types is no...

  • Page 398

    Coolant level the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine off and cold, the level of the engine coolant (antifreeze) in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely ...

  • Page 399

    • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms.90032) and distilled water for proper corrosion pro- tection of your engine which contains aluminum com- ponents. • make sure that the coolant expansion bottle overflow hoses are not kinked or obst...

  • Page 400

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids and lubricants” in “technical specifications” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle...

  • Page 401

    Transfer case fluid level check the fluid level should be to the bottom edge of the fill hole (a) when the vehicle is in a level position. Adding fluid add fluid at the filler hole, until it runs out of the hole, when the vehicle is in a level position. Drain first remove the fill plug (b), then the...

  • Page 402

    Note: no chemical flushes should be used in any trans- mission; only the approved lubricant should be used. Caution! Using a transmission fluid other than the manufactur- er’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder, and will require mo...

  • Page 403

    5. Place the gear selector momentarily into each gear position (allowing time for the transmission to fully engage in each position), ending with the transmission in park. 6. Remove the dipstick, wipe it clean and reinsert it until seated. 7. Remove the dipstick again and note the fluid level on bot...

  • Page 404

    Note: to prevent dirt and water from entering the transmission after checking or replenishing fluid, make sure that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tub...

  • Page 405

    Tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designation. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to th...

  • Page 406

    Tire identification number (tin) the tin may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 407

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located be- hind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hour...

  • Page 408

    Tire loading and tire pressure note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 406 servicing and maintenance.

  • Page 409

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 410

    Steps for determining correct load limit— (1) locate the statement “the combined weight of occupants and cargo should never exceed xxx kg or xxx lbs.” on your vehicle’s placard. (2) determine the combined weight of the driver and passengers that will be riding in your vehicle. (3) subtract the combi...

  • Page 411

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them. 8 servicing and maintenance 409.

  • Page 412

    Tires — general information tire pressure proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Four primary areas are affected by improper tire pressure: • safety and vehicle stability • economy • tread wear • ride comfort safety warning! • improperly i...

  • Page 413

    Fuel economy underinflated tires will increase tire rolling resistance resulting in higher fuel consumption. Tread wear improper cold tire inflation pressures can cause abnormal wear patterns and reduced tread life, resulting in the need for earlier tire replacement. Ride comfort and vehicle stabili...

  • Page 414

    Pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire ...

  • Page 415

    Run flat tires — if equipped run flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the run flat mode. A run flat mode occurs when the tire inflation pressure is of/or below 14 psi...

  • Page 416

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (1.6 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information....

  • Page 417

    Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold ...

  • Page 418

    Warning! (continued) • failure to equip your vehicle with tires having ad- equate speed capability can result in sudden tire failure and loss of vehicle control. Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire types all s...

  • Page 419

    Snow tires some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a “mountain/snowflake” symbol on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the origi- nal equipment tires. Use snow tires only in sets of...

  • Page 420

    Spare by looking at the spare tire description on the tire and loading information placard located on the driver’s side door opening or on the sidewall of the tire. Compact spare tire descriptions begin with the letter “t” or “s” preceding the size designation. Example: t145/80d18 103m. T, s = tempo...

  • Page 421

    Handling. Since it is not the same as your original equip- ment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Warning! Limited use spares are for emergency use only. Instal- lation of this limited use spare tire affects vehicle handling....

  • Page 422

    Select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels. Do not use any products on dark vapor or black satin chrome wheels. They will permanently dam- age this finish and such damage is not covered by the new vehicle limited warranty. Caution! Do not use scouring pads, steel wool, a...

  • Page 423

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 424

    The suggested rotation method is the “rearward-cross” shown in the following diagram. Caution! Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. Tire rotation schedule...

  • Page 425

    On wet pavement, as measured under controlled condi- tions on specified government test surfaces of asphalt and concrete. A tire marked c may have poor traction performance. Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acce...

  • Page 426

    We recommend you use storage mode for more infor- mation refer to (“instrument cluster display menu items” in “getting to know your instrument panel”). • clean and protect the painted parts by applying protec- tive waxes. • clean and protect polished metal parts by applying protective waxes. • apply...

  • Page 427

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resis- tance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • ro...

  • Page 428

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8,274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty r...

  • Page 429

    • be especially careful when washing the windows by following the directions for “care of fabric top win- dows.” washing – use mopar car wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles. If extra cleaning is required, use mopar convertible cloth top cleaner or eq...

  • Page 430

    2. When washing, never use hot water or anything stron- ger than a mild soap. Never use solvents such as alcohol or harsh cleaning agents. 3. Always rinse thoroughly with cold water, then wipe with a soft and slightly moist, clean cloth. 4. When removing frost, snow or ice, never use a scraper or de...

  • Page 431

    Replace the belts if they appear frayed or worn or if the buckles do not work properly. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immed...

  • Page 432

    Note: if equipped with light colored leather, it tends to show any foreign material, dirt, and fabric dye transfer more so than darker colors. The leather is designed to for easy cleaning, and fca recommends mopar total care leather cleaner applied on a cloth to clean the leather seats as needed. Ca...

  • Page 433: Technical Specifications

    Technical specifications contents 䡵 vehicle identification number . . . . . . . .432 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . . .432 䡵 wheel and tire torque specifications . .432 ▫ torque specifications . . . . . . . . . . . . . . . . . . . .433 䡵 fuel requirements. . . . . . . . ....

  • Page 434

    Vehicle identification number the vehicle identification number (vin) is found on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears underbody, on the right side of the frame rail near the center of the vehicle, as ...

  • Page 435

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/bolt socket size 100 ft-lbs (135 n·m) 1/2” x 20 19 mm **use only your authorized dealer recommended lug nuts/ bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the t...

  • Page 436

    Fuel requirements 3.6l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when using high-quality unleaded “regular” gasoline having an octane rating of 87 as specified by the (r+m)/2 method. The use of higher octane “premium” gaso- ...

  • Page 437

    Gasoline is recommended. Visit www.Toptiergas.Com for a list of top tier detergent gasoline retailers. Indiscriminate use of fuel system cleaning agents should be avoided. Many of these materials intended for gum and varnish removal may contain active solvents or similar ingredients. These can harm ...

  • Page 438

    Cng and lp fuel system modifications modifications that allow the engine to run on compressed natural gas (cng) or liquid propane (lp) may result in damage to the engine, emissions, and fuel system compo- nents. Problems that result from running cng or lp are not the responsibility of the manufactur...

  • Page 439

    Note: intentional tampering with the emissions control system can result in civil penalties being assessed against you. Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon mon- oxide poisoning: • do not inhale exhaust gase...

  • Page 440

    Fluid capacities u.S. Metric fuel (approximate) two door models 18.6 gallons 70 liters four door models 22.5 gallons 85 liters engine oil with filter 3.6l engine 6 quarts 5.6 liters cooling system * 3.6l engine (mopar antifreeze/ engine coolant 10 year/150,000 mile formula or equivalent) 10.5 quarts...

  • Page 441

    Fluids and lubricants engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive tech- nology) or equivalent meeting the requirements of fca material standard ms.90032. Engine oil we recommend you...

  • Page 442

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine dam- age and may decrease corrosion protection. Organic additive technology (oat) engine coolant is differ- ent and should not be mixed with hyb...

  • Page 443

    Chassis component fluid, lubricant, or genuine part automatic transmission – if equipped use only atf+4 automatic transmission fluid. Failure to use atf+4 fluid may affect the function or performance of your transmission. We recommend mopar atf+4 fluid. Manual transmission – if equipped we recommend...

  • Page 445: Multimedia

    Multimedia contents 䡵 radio 130 . . . . . . . . . . . . . . . . . . . . . . . . . . . .445 ▫ operating instructions — radio mode . . . . . . . .452 ▫ operation instructions — cd mode for cd and mp3 audio play. . . . . . . . . . . . . . . . . . . . . . . .447 ▫ notes on playing mp3 files . . . . . . ...

  • Page 446

    ▫ regulatory and safety information . . . . . . . . . .467 䡵 cd/dvd disc maintenance . . . . . . . . . . . .469 䡵 uconnect phone — if equipped . . . . . . . .469 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .471 ▫ help command . . . . . . . . . . . . . . . . . . . . . . . .472 ▫...

  • Page 447

    Radio 130 operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn off the radio. Electron...

  • Page 448

    4. Adjust the minutes using the right side tune/scroll control knob. Push the tune/scroll control knob to save time change. 5. To exit, push any button/knob, or wait five seconds. Rw/ff pushing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next frequency in the dire...

  • Page 449

    Within five seconds after pushing the set/rnd button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: push the set/rnd button twice and set 2 will show in the displa...

  • Page 450

    Caution! • this cd player will accept 4–3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • the radio 130 is a single cd player. Do not attempt to insert a second cd if ...

  • Page 451

    Set/rnd button (random play button) push this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Push the right seek button to move to the next randomly selected track. Push the rnd b...

  • Page 452

    Writing ⬙ are most likely multi-session discs. The use of multi-session for cd audio or mp3 playback may result in longer disc loading times. Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause...

  • Page 453

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 454

    Radio 130 with satellite radio operating instructions — radio mode note: the ignition switch must be in the on/run or acc position to operate the radio. Power switch/volume control (rotary) push the on/volume control knob to turn on the radio. Push the on/volume control knob a second time to turn of...

  • Page 455

    If your vehicle is not equipped with or this feature is not available on your vehicle, a “not equipped with uconnect phone” message will display on the radio screen. Phone button uconnect phone — if equipped push this button to operate the uconnect phone feature (if equipped). Refer to “uconnect pho...

  • Page 456

    Push the rotary tune/scroll control knob a second time and mid will display. Turn the tune/scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary tune/scroll control knob a third time and treble will display. Turn the tune/scroll control knob to the rig...

  • Page 457

    Program type 16-digit character dis- play personality persnlty public public rhythm and blues r & b religious music rel musc religious talk rel talk rock rock soft soft soft rock soft rck soft rhythm and blues soft r&b sports sports talk talk top 40 top 40 weather weather by pushing the seek button ...

  • Page 458

    Within five seconds after pushing the set/rnd button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: push the set/rnd button twice and set 2 will show in the displa...

  • Page 459

    Caution! • this cd player will accept 4–3/4 inch (12 cm) discs only. The use of other sized discs may damage the cd player mechanism. • do not use adhesive labels. These labels can peel away and jam the player mechanism. • the radio 130 is a single cd player. Do not attempt to insert a second cd if ...

  • Page 460

    Set/rnd button (random play button) push this button while the cd is playing to activate random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Push the right seek button to move to the next randomly selected track. Push the rnd b...

  • Page 461

    Writing ⬙ are most likely multi-session discs. The use of multi-session for cd audio or mp3 playback may result in longer disc loading times. Supported mp3 file formats the radio will recognize only files with the *.Mp3 exten- sion as mp3 files. Non-mp3 files named with the *.Mp3 extension may cause...

  • Page 462

    Playback of mp3 files when a medium containing mp3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the mp3 files. Loading times for playback of mp3 files may be affected by the following: • med...

  • Page 463

    Note: the aux device must be turned on and the device’s volume set to the proper level. If the aux audio is not loud enough, turn the device’s volume up. If the aux audio sounds distorted, turn the device’s volume down. Time button (auxiliary mode) push this button to change the display to time of d...

  • Page 464

    Selecting uconnect (satellite) mode push the sat button until ⬙ sat ⬙ appears in the display. A cd may remain in the radio while in the satellite radio mode. Satellite antenna to ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within...

  • Page 465

    Additional three seconds will make the radio display the song title all of the time (push and hold again to return to normal display). Rw/ff pushing the rw (rewind) or ff (fast forward) buttons causes the tuner to search for the next channel in the direction of the arrows. Tune control turn the rota...

  • Page 466

    Allows a total of 12 satellite channels to be stored into push button memory. The channels stored in set 2 memory can be selected by pushing the push button twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 these buttons tune the radio to the channe...

  • Page 467

    The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as uconnect software) is installed. Warning! • it is not possible to know or to predict all of the possible outcomes if your vehicle’s systems are breached....

  • Page 468

    The right-hand control is a rocker-type switch with a push-button in the center and controls the volume and mode of the sound system. Pushing the top of the rocker switch will increase the volume, and pushing the bottom of the rocker switch will decrease the volume. Pushing the center button will ma...

  • Page 469

    Multiple-disc cd player is equipped on the vehicle, the center button will select the next available cd in the player. Aux/usb/mp3 control — if equipped this feature allows an external usb device to be plugged into the usb port, located in the center console. Connecting an electronic audio device to...

  • Page 470

    Environments, such as aboard airplanes. If you are unsure of restrictions, you are encouraged to ask for authorization before turning on the wireless radio. This device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the followi...

  • Page 471

    Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch...

  • Page 472

    Uconnect phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The uconnect phone is driven through your bluetooth “hands-free profile” mobile phone. Uconnect features bl...

  • Page 473

    Voice command button warning! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. Actual button location ...

  • Page 474

    “phonebook new entry,” or you can break the com- pound form command into two voice commands: “phonebook” and “new entry.” please remember, the uconnect phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you. Voice command tre...

  • Page 475

    • you will then be asked to give your mobile phone a priority level between one and seven, with one being the highest priority. You can pair up to seven mobile phones to your uconnect phone. However, at any given time, only one mobile phone can be in use, connected to your uconnect system. The prior...

  • Page 476

    Phonebook download – automatic phonebook transfer from mobile phone if equipped and specifically supported by your phone, uconnect phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific bluetooth phones with phone book access profile may supp...

  • Page 477

    • when prompted, enter the number designation (e.G., “home,” “work,” “mobile,” or “other”). This will allow you to store multiple numbers for each phonebook entry, if desired. • when prompted, recite the phone number for the phone- book entry that you are adding. After you are finished adding an ent...

  • Page 478

    To delete a uconnect phonebook entry using voice com- mands: 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say “phonebook delete.” 3. After you enter the phonebook delete menu, you will then be asked for the name of the entry that you wish to delete. You can ...

  • Page 479

    Answer or reject an incoming call — no call currently in progress when you receive a call on your mobile phone, the uconnect phone will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. Push the phone button to accept the call. To reject the call, push and...

  • Page 480

    Conference call when two calls are in progress (one active and one on hold): 1. Push and hold the phone button until you hear a double beep, indicating that the two calls have been joined into one conference call. Three-way calling to initiate three-way calling, push the voice command button while a...

  • Page 481

    The vehicle battery condition dictates cessation of the call on the uconnect phone and transfer of the call to the mobile phone. 2. After the ignition is cycled to off, a call can continue on the uconnect phone for a certain duration, after which the call is automatically transferred from the uconne...

  • Page 482

    Note: • the emergency number dialed is based on the country where the vehicle is purchased (911 for the u.S. And canada and 060 for mexico). The number dialed may not be applicable with the available mobile service and area. • if supported, this number may be programmable on some systems. To do this...

  • Page 483

    You can use your uconnect phone to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some services require immediate response selection. In some instances, that may be too quick for use of the uconnect phone. When calling a number with y...

  • Page 484

    To turn confirmation prompts on or off using voice com- mand: 1. Push the phone button to begin. 2. After the “ready” prompt and the following beep, say: • “setup confirmations prompts on” • “setup confirmations prompts off” phone and network status indicators if available on the radio and/or on a p...

  • Page 485

    Advanced phone connectivity transfer call to and from mobile phone the uconnect phone allows ongoing calls to be transferred from your mobile phone to the uconnect phone without terminating the call. To transfer an ongoing call from your uconnect phone paired mobile phone to the uconnect phone or vi...

  • Page 486

    Delete uconnect phone paired mobile phones • push the phone button to begin. • after the “ready” prompt and the following beep, say “setup phone pairing.” • at the next prompt, say “delete” and follow the prompts. • you can also push the voice command button at any time while the list is being playe...

  • Page 487

    Voice command for best performance: • adjust the rearview mirror to provide at least ½ inch (1 cm) gap between the overhead console (if equipped) and the mirror. • always wait for the beep before speaking. • speak normally without pausing, just as you would speak to a person sitting a few feet/meter...

  • Page 488

    Far end audio performance audio quality is maximized under: • low-to-medium blower setting • low-to-medium vehicle speed • low road noise • smooth road surface • fully closed windows • dry weather conditions • operation from the driver’s seat • performance, such as audio clarity, echo, and loudness ...

  • Page 489

    • you can either say the message you wish to send or say “list messages.” there are 20 preset messages. To send a message, push the voice command button while the system is listing the message and say “send.” uconnect phone will prompt you to say the name or number of the person you wish to send the...

  • Page 490

    Bluetooth communication link mobile phones have been found to lose connection to the uconnect phone. When this happens, the connection can generally be reestablished by switching the phone off/on. Your mobile phone is recommended to remain in bluetooth on mode. Power-up after switching the ignition ...

  • Page 491

    10 multimedia 489.

  • Page 492

    Voice commands primary alternate (s) zero one two three primary alternate (s) four five six seven eight 490 multimedia.

  • Page 493

    Primary alternate (s) nine star (*) plus (+) pound (#) add location all call cancel confirmation prompts continue delete dial download edit emergency english erase all espanol francais help primary alternate (s) home language list names list phones mobile mute mute off new entry no other pair a phon...

  • Page 494

    Primary alternate (s) set up phone settings or phone set up towing assistance transfer call uconnect tutorial voice training work yes general information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the ...

  • Page 495

    Note: if you do not say a command within a few seconds, the system will present you with a list of options. If you would like to interrupt the system while it lists options, push the voice command button, listen for the beep, and say your command. Pushing the voice command button while the system is...

  • Page 496

    In this mode, you can say the following commands: • “radio am” (to switch to the radio am mode) • “radio fm” (to switch to radio fm mode) • “sat” (to switch to satellite radio mode) • “disc” (to switch to the disc mode) • “usb” (to switch to usb mode) • “bluetooth streaming” (to switch to bluetooth ...

  • Page 497

    Disc mode to switch to the disc mode, say “disc.” in this mode, you may say the following commands: • “track” (#) (to change the track) • “next track” (to play the next track) • “previous track” (to play the previous track) • “main menu” (to switch to the main menu) usb mode to switch to usb mode, s...

  • Page 498

    Setup to switch to system setup, you may say one of the following: • “change to setup” • “switch to system setup” • “main menu setup” • “switch to setup” in this mode, you may say the following commands: • “language english” • “language french” • “language spanish” • “tutorial” • “voice training” no...

  • Page 499: Customer Assistance

    Customer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . . .498 ▫ prepare for the appointment . . . . . . . . . . . . . .498 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . .498 ▫ be reasonable with requests . . . ...

  • Page 500

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 501

    Any communication to the manufacturer’s customer center should include the following information: • owner’s name and address • owner’s telephone number (home and office) • authorized dealer name • vehicle identification number (vin) • vehicle delivery date and mileage fca us llc customer center p.O....

  • Page 502

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommunica- tion devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 503

    Warning! Engine exhaust (internal combustion engines only), some of its constituents, and certain vehicle compo- nents contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids con- tained in vehicles and c...

  • Page 504

    In canada if you believe that your vehicle has a safety defect, you should contact the customer service department imme- diately. Canadian customers who wish to report a safety defect to the canadian government should contact transport canada, motor vehicle defect investigations and recalls at 1-800...

  • Page 505

    Owner’s manuals these owner’s manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific fca us llc vehicles. Included are starting, operating, emergency and maintenance proce- dures as well as specifications, capabilities and safety tips. Cal...

  • Page 507: Index

    Index 12.

  • Page 508

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . . .432 adding engine coolant (antifreeze) . . . . . . . . . . . . .394 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .310 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . .434 air bag . . . ....

  • Page 509

    Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195, 374 charging system light . . . . . . . . . . . . . . . . . . . .195 keyless key fob replacement . . . . . . . . . . . . . . . .20 belts, seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277 body mechanism lu...

  • Page 510

    Clean air gasoline . . . . . . . . . . . . . . . . . . . . . . . . .434 cleaning wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .419 climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6...

  • Page 511

    Driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .328 dual top. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72, 75 electrical outlet, auxiliary (power outlet) . . . . . . . . .174 electrical power outlets . . . . . . . . . . . . . . . . . . . . . .174 electric ...

  • Page 512

    Filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . .377 air conditioning . . . . . . . . . . . . . . . . . . . . . .69, 383 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . .377, 439 engine oil disposal . . . . . . . . . . . . . . . . . . . . . . .377 flashers ha...

  • Page 513

    Gasoline, clean air . . . . . . . . . . . . . . . . . . . . . . . . .434 gasoline (fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . .434 gasoline, reformulated . . . . . . . . . . . . . . . . . . . . . .434 gauges fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200...

  • Page 514

    Intermittent wipers (delay wipers). . . . . . . . . . . . . . .58 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 inverter, power . . . . . . . . . . . . . . . . . . . . . . . . . . . .177 ipod/usb/mp3 control bluetooth streaming audio . . . . . . . . . . . . . . . . .4...

  • Page 515

    Security alarm . . . . . . . . . . . . . . . . . . . . . . . . . .200 service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .341 side marker . . . . . . . . . . . . . . . . . . . . . . . . . . . .343 tire pressure monitoring (tpms) . . . . . . . . . . . . .203 traction control . . . ...

  • Page 516

    Filter disposal . . . . . . . . . . . . . . . . . . . . . . . . . . .377 identification logo . . . . . . . . . . . . . . . . . . . . . . .376 materials added to . . . . . . . . . . . . . . . . . . . . . . .377 pressure warning light . . . . . . . . . . . . . . . . . . . .199 recommendation . . . . ....

  • Page 517

    Radio operation . . . . . . . . . . . . . . . . . . . . . . . . . . .467 rear axle (differential) . . . . . . . . . . . . . . . . . . . . . .398 rear swing gate . . . . . . . . . . . . . . . . . . . . . . . . . . .171 rear wiper/washer. . . . . . . . . . . . . . . . . . . . . . . . . .59 recreationa...

  • Page 518

    Front seat . . . . . . . . . . . . . . . . . . . . . . .237, 238, 240 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277 operating instructions . . . . . . . . . . . . . . . . . . . . .240 pregnant women . . . . . . . . . . . . . . . . . . . . . . . . .245 pretensioners . . . ...

  • Page 519

    Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .309 speed control (cruise control) . . . . . . . . . . . . . . . . .306 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22, 283 automatic transmission . . . . . . . . . . . . . . . . . . . .283 cold weather . ....

  • Page 520

    Snow tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .417 spare tire . . . . . . . . . . . . . . . . . . . . . . .351, 417, 418 spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .413 tread wear indicators . . . . . . . . . . . . . . . . . . . . .413 tire safety infor...

  • Page 521

    Untwisting procedure, seat belt . . . . . . . . . . . . . . . .243 vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 variance, compass. . . . . . . . . . . . . . . . . . . . . . . . . .188 vehicle identification number (vin) . . . . . . . . . . . . .432 vehicle loading . . ....

  • Page 522

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 523

    First edition printed in u.S.A. 17mk74-126-aa ©2016 fca us llc. All rights reserved. Jeep is a registered trademark of fca us llc. Stick with the specialists ® 17jk72-126-ab second edition.