Summary of ZR44 Hi-Mass
Page 1
User manual zr44 hi-mass p/n 35010032-b tm.
Page 2
2 safety information safety information...................................................................................................................... 3 product overview ....................................................................................................................... 6 p...
Page 3
Safety information 3 safety information the following symbols are used to identify important safety information: caution! Safety hazard. Risk of personal injury. Caution! Burn hazard. Hot surface. Do not touch. Danger! Hazardous voltage. Contact will cause electric shock. Caution! Fire hazard. Warni...
Page 4
4 safety information • do not remove the covers or attempt to repair a faulty machine. Refer any service not described in this manual to martin. • do not operate the machine if any parts are damaged, defective or missing. • moisture and electricity do not mix. Do not aim smoke output at electrical c...
Page 5
Safety information 5 p r e v e n t i n g b r e a t h i n g p r o b l e m s • a smoke machine can operate safely only with the smoke fluid it is designed for. Use the machine only with fluids specified under “smoke fluid options” on page 13 or you may cause the release of toxic gases, presenting a se...
Page 6
6 product overview product overview p r o d u c t d e s c r i p t i o n the jem zr44 hi-mass™ is a reliable and highly efficient fogger capable of precise fog delivery from subtle to massive. Ideal for a variety of settings from small venues to huge stadiums and arenas, it features advanced technolo...
Page 7
Quick start 7 quick start you are no doubt eager to switch on the machine and try it out by making a lot of fog. This section tells you how to do that. However, please also make the time to read the safety and servicing instructions in the remainder of this manual. S e t t i n g u p locate the machi...
Page 8
8 installation and setting up installation and setting up danger! Do not operate the smoke machine until you have read and observed all the precautions listed under “safety information” on page 3. L o c a t i o n the smoke machine may be located on the floor or may be suspended using the flying brac...
Page 9
Installation and setting up 9 check that the local ac voltage is appropriate, as indicated on the machine’s serial number label. If your ac voltage is outside the appropriate range, do not use the machine. Contact martin service for assistance. S e t t i n g u p fill the fluid tank with martin-appro...
Page 10
10 control settings control settings o v e r v i e w the unit is controlled using the remote control. You can control it in these ways: • manual firing by holding down the fog button • automatic fog bursts using a repeating timer m a n u a l f i r i n g hold down the fog button. The machine will pro...
Page 11
Dmx control 11 dmx control o v e r v i e w dmx is a digital control system widely used in entertainment and architectural lighting. Any controller meeting the dmx-512 standard may be used to control and program the fog output of the smoke machine. C o n n e c t i o n the smoke machine provides both ...
Page 12
12 dmx control s e t t i n g t h e d m x a d d r e s s each unit on a dmx system must be allocated an address so that the dmx controller can send separate commands to the unit. On the smoke machine, the dmx address is set using the bank of switches (“dip switches”) on the back panel next to the dmx ...
Page 13
Fog fluid types 13 fog fluid types the following types of martin/jem fog fluid are suitable for use in this machine. Each produces a different effect as described below. Martin supplies high quality fog fluids that are based on ultra-pure deionized water. Use only the following genuine martin/jem fo...
Page 14
14 basic service basic service before servicing the smoke machine, read and observe all the precautions listed in “safety information” on page 3. Any service not described in this section must be carried out by a martin service technician. C l e a n i n g excessive dust, smoke fluid, and dirt build-...
Page 15
Troubleshooting 15 troubleshooting problem probable cause(s) suggested remedy machine not at operating temperature wait 10 to 15 minutes machine not powered up or heaters disabled ensure mains power switch on, enable heaters by pressing fog machine will not produce fog when remote control fog button...
Page 16
16 specifications specifications physical length: 685 mm (27.0 in.) width: 345 mm (13.6 in.) height: 225 mm (8.9 in.) dry weight: 19 kg (41.9 lbs.) performance max. Fog output (approx.): 1200 m 3 max. Operating time at full output (approx.) operating time: continuous, automatic level adjustment warm...
Page 17
Specifications 17 exterior surface temperature, steady state: 50° c (122° f) max. Nozzle temperature: 220° c (392° f) approvals etl approvals (cetlus) pending included items user manual remote control container 9.5 l a c c e s s o r i e s digital multi-function remote control ..........................
Page 18
18 notes notes.
Page 19
19.
Page 20
Martin professional a/s,olof palmes allé 18, dk-8200,aarhus n phone: +45 87 40 00 00 internet: www.Martin.Com.