Jenn-Air JMC2430DS Installation Instructions Manual - Installation Requirements
2
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
■
Phillips screwdriver
■
Flat-blade screwdriver
■
Measuring tape
■
Level
■
Drill (for wall cabinet
installations)
■
¹ ⁄
8
" (3 mm) drill bit (for wall
cabinet installations)
■
1" (2.5 cm) drill bit (for wall
cabinet installations)
Parts Needed
■
UL-listed or CSA-approved conduit connector
■
UL-listed wire connectors
Parts Needed – Flush Installation
■
W10752697A Stainless steel flush installation kit for 30"
(76.2 cm) models
■
W10752698A Stainless steel flush installation kit for 27"
(68.6 cm) models
To order, see the “Assistance or Service” section of the
Use and Care Guide.
Parts Supplied
■
For installation above single built-in oven, the junction box
must located inside upper cabinet.
■
If you are installing the junction box on rear wall behind
the microwave oven, the junction box must be recessed
and located in the upper or lower right or left corner of
the cabinet; otherwise, the microwave oven will not fit
into the cabinet opening.
■
Microwave oven support surface must be solid, level
and flush with bottom of cabinet cutout. Floor must be
able to support a weight of 90 lbs (41.0 kg).
IMPORTANT: To avoid damage to your cabinets, check with
your builder or cabinet supplier to make sure that the materials
used will not discolor, delaminate or sustain other damage. This
oven has been designed in accordance with the requirements
of UL and CSA International and complies with the maximum
allowable wood cabinet temperatures of 194°F (90°C).
Product Dimensions
27" (68.6 cm) and 30" (76.2 cm) Microwave Ovens
A
B
C
D
A. Spacer bars (2)
B. Bottom vent (1)
C. ³⁄
8
" hex-head washer
screws (4)
D. ¾" pan-head screws (4)
Check local codes. Check existing electrical supply.
See “Electrical Requirements.”
It is recommended that all electrical connections be made
by a licensed, qualified electrical installer.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■
Cabinet opening dimensions that are shown must be
used. Given dimensions provide minimum clearance with
microwave oven.
■
Recessed installation area must provide complete
enclosure around the recessed portion of the microwave
oven.
■
Grounded electrical supply is required. See “Electrical
Requirements” section.
■
Electrical supply junction box should be located 3" (7.6 cm)
maximum below the support surface when the microwave
oven is installed in a wall cabinet. A 1" (2.5 cm) minimum
diameter hole should have been drilled in the left rear
corner of the support surface to pass the appliance cable
through to the junction box.
B
E
C
D
A
27" (68.6 cm) models
A. 25³⁄
8
" (64.5 cm)
B. 19
7
/
8
" (50.3 cm) overall height
C. 26³⁄
4
" (68.0 cm) overall width
D. 21¹⁄
2
" (54.6 cm)
E. 17³⁄
8
" (44.1 cm)
30" (76.2 cm) models
A. 28³⁄
8
" (72.1 cm)
B. 19
7
/
8
" (50.3 cm) overall height
C. 29³⁄
4
" (75.6 cm) overall width
D. 21¹⁄
2
" (54.6 cm)
E. 17³⁄
8
" (44.1 cm)
27" (68.6 cm) and 30" (76.2 cm) Microwave Oven Spacer Kit
A
27" (68.6 cm) models
A. 26³⁄
4
" (67.9 cm) overall width
30" (76.2 cm) models
A. 29³⁄
4
" (75.6 cm) overall width
NOTE: The microwave oven spacer kit will allow the microwave
oven to be installed in a 17³⁄
8
" to 17³⁄
4
" (44.1 to 45.1 cm)
maximum cutout height.
A microwave oven spacer kit is available from your dealer that
will allow the microwave oven to be installed in a 19" to 19¹³⁄
16
"
(48.3 to 50.2 cm) maximum cutout height. Match the oven size
to the following kits:
27" (68.6 cm) Stainless Steel – Model W10469901
30" (76.2 cm) Stainless Steel – Model W10469903
To order, see the “Assistance or Service” section of the
Use and Care Guide.