K+H O 500 C Installation And Operation Manual - page 23
Page 23
3.3 System Menu
(Eprom-Version-Nr. KH 1.038)
Description of the Menu Steps:
K+H O 500 C
- System Menu -
Menu headline
1 Brightness
Here the brightness of the VF display can be
adjusted. The selection of the steps can be
made by pressing the +/- increment keys.
The new setting is activated by pressing
ENTER.
2 MIDI Settings
In this menu the internal MIDI/RS-232 –
interfaces are determined. The individual
options are spread across several menu-
subpages, which are selected by the LEFT /
RIGHT - arrow keys. For more details see
chapter 4.2.
3 Security Level / Password
In this menu step it is possible to select 6 dif-
ferent user security levels (0...5) for operating
the O 500 C. By hiding menupoints it is
possible to make adjustments and operation
of the O 500 C accessible to differnt groups
of users with different background /
knowledge, to avoid misuse. Apart from this
it is possible to make the everyday use much
easier, because for this purpose all rarely
needed adjustments are not accessible in
normal operation, so it will be less confusing
and the „toy effect“ is kept low.
The security levels can be recalled with the
numbers 0 to 5 after the correct password
has been entered. First, the cursor has to be
moved to the right side of the display. After
pressing ENTER, the correct password
positions can be reached by pressing the
LEFT / RIGHT arrow keys, and the correct
characters are selected by pressing the +/-
increment keys. After pressing ENTER, the
writing „unlocked“ appears, if the password
was correct. After moving the cursor to the
left display side at
Security Level Nr.
the
number of the desired security level is entered
by the +/- increment keys. By pressing the
ENTER key the level is changed and locked
again.
4 Change of Password
This menu changes the name of the
password of the digital controller. First, the
active password has to be entered as
described above and to be confirmed by
pressing ENTER. Now the display will show
„unlocked“ and with the DOWN arrow key the
CHANGE PASSWORD page will be opened.
After pressing ENTER the display will show
the actual password, which now can be
changed / modified by pressing the LEFT /
RIGHT arrow keys and the +/- increment
keys. When ready, the new password should
be noted and confirmed by pressing ENTER.
Important note:
If the password can not be
remembered it will not be possible to find it
on site. In this case it is recommended to
initialize the O 500 C by activating the menu
Options
Units
Default Settings
0
1
2
3
4
5
1
Brightness
Display [%]
25,50,100 %
100
X
X
X
X
Channel
1...16
1
out [out only / out-trough / loop]
---
out only
Baudrate [Midi / RS232]
31250 / 9600
RS-232 (9600)
ParaChg [on / off]
---
off
TX-Chn
1...16, OCM
1
Midi-Monitor [start]
---
---
Load Level Nr.
0...5
5
Passwort
---
locked
4
Change Password
(Name)
---
0000
X
5
IR Control
[on / off]
---
on
X
X
X
6
AES Stat./ Sample Rate
S.Rate [kHz]
---
---
X
X
Reeboot
---
---
Initialize
---
---
8
Service Section
Check LED Bargraph
---
---
X
9
Version No. (Eprom)
---
---
App V KH 1.0XX
X
X
X
X
X
X
10
Logo
on / off
---
on
X
X
X
X
3
Security Level / Password
2
No. / Name of Menu Step
Midi Settings
7
Version No. (Betriebssystem)
X
K+H O 500 C
0
System Menu
X
X
X
X
X
X
X
User Security Levels