Kaba Simplex 7104 Series Installation Instructions Manual - Kaba Simplex

Other manuals for Simplex 7104 Series: Installation Instructions Manual

Summary of Simplex 7104 Series

  • Page 1

    7 1 0 4 series installation instructions.

  • Page 2

    2 important: please keep these instructions. The combination of this lock has been factory preset: 2 and 4 pressed together, then 3. Warning for your own safety, you must change the combination at the time of installation. Please read and follow all directions carefully since every installation is u...

  • Page 3

    3 for technical assistance please call 1-800-849-tech (8324) or 336-725-1331 table of contents checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 determining the hand of your door . . . . . . . . . . . . . . . ...

  • Page 4: Checklist

    4 checklist use this checklist to make sure that everything has been included. A – front lock b – trim plate c – 2 3 ⁄ 4 " backset latch (7004) – adjustable latch (7104) d – inside thumbturn assembly e – inside combination change assembly f – strike plate screw pack: g – 4 thru-bolts (3") h – 4 comb...

  • Page 5: B. Adjusting The Latch

    5 a. Determining the lock location install the lock with the exterior thumbturn at least 7" (18 cm) above your primary lock set so it is com- fortable to operate and not in the way when you turn the door knob. *a minimum stile width of 4" (10.16 cm) is required for mounting, (see figure 2-1). B. Adj...

  • Page 6

    6 d. Drilling holes in the door caution: positioning and drilling must be done straight to ensure troublefree operation of the 7000 series lockset. Improper drilling may result in excessive force being exerted on the lock which may result in the premature wearing of its mechanical parts. You must do...

  • Page 7: F. Installing The Latch

    7 f. Installing the latch f-1 for doors that swing outward, the curved edge of the latch should be facing inward towards the room. For doors that swing inward, the curved edge of the latch should be facing outward away from the room. F-2 put the latch into the 1" (25 mm) hole, (see figure 6-1). F-3 ...

  • Page 8: Kaba Simplex

    Kaba simplex ® limited warranty kaba access control warrants this product to be free from defects in material and workmanship under normal use and service for a period of one (1) year. Kaba access control will repair or replace, at our discretion, locks found by kaba access control analysis to be de...

  • Page 9

    K a b a a c c e s s c o n t r o l 2 9 4 1 in d ia n a a v e n u e w in s t o n -s a l e m , n c 2 7 19 9 -3 7 7 0 n o p o s t a g e n e c e s s a r y if m a il e d in t h e u n it e d s t a t e s b u s i n e s s r e p l y m a il f ir s t -c l a s s m a il p e r m it n o . 15 6 3 p o s t a g e w il l...

  • Page 10

    T h a n k y o u fo r p u r c h a s in g o u r p r o d u c t. In o r d e r to p r o te c t y o u r in v e s tm e n t a n d to e n a b le u s to b e tt e r s e r v e y o u in th e fu tu re , p le a s e fi ll o u t th is re g is tr a ti o n c a r d a n d r e tu r n it to k a b a a c c e s s c o n tr o ...

  • Page 11: I. Installing The Lock

    8 i. Installing the lock - for 1 3 ⁄ 4 " - 1 3 ⁄ 4 " (33 - 44 mm) thick doors, use the 2 3 ⁄ 8 " (45 mm) thru bolts. - for 2"- 2 1 ⁄ 4 " (51- 57 mm) thick doors, use the 3" (76 mm) thru bolts. Mount the lock from the outside of the door. I-1 insert the tailpiece y into the horizontal cutout of the l...

  • Page 12

    9 j. Checking the lock’s operation important: the following steps must be performed while the door is open. J-1 turn the outside thumbturn to the left (counterclockwise) until it stops, then release it. J-2 press the preset factory combination (2 and 4 pressed together, release, then 3, and release)...

  • Page 13: K. Installing The Strike

    10 j-9 insert the tip of a phillips-head screwdriver into the combination change assembly b (see figure 10-3). J-10 turn the central piece to the right (clockwise) until it stops, do not force, (approximately 30˚ degrees). J-11 remove the screwdriver; the central piece should automatically return to...

  • Page 14

    11 l-2 hold the chamber in one hand by the screw tab (b) on each end with the key-stems (c) facing you and the control shaft (d) at the bottom (see figure 12-2). L-3 rotate the control shaft (d) counter-clockwise and release to clear the chamber (see figure 12-2). L-4 look at the 5 code gears (e). I...

  • Page 15: M. Troubleshooting

    12 testing: enter the combination you preset during the reset process. Turn the outside thumbturn to the right (clockwise). The latch should retract. If the latch does not retract, turn the outside thumbturn left (counter-clockwise) and release, then enter the code again. M. Troubleshooting ? Lock f...

  • Page 16

    Kaba access control 2941 indiana avenue winston-salem, nc 27105 usa tel: (800) 849-8324 (336) 725-1331 fax: (800) 346-9640 (336) 725-3269 www.Kabaaccess.Com pkg0782 0307.