Kalkhoff Bosch Active Line Original User Manual - Drive Unit Cruise/
English–
1
0 276 001 SAI | (14.8.13)
Bosch eBike Systems
Drive Unit Cruise/
HMI Intuvia
Safety Notes
Read all safety warnings and all instruc-
tions.
Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Save all safety warnings and instructions for future
reference.
The term “battery pack” used in these operating instructions
refers both to standard battery packs (battery packs with
holder on the bike frame) and to rack-type battery packs
(battery packs with holder in the rear rack/carrier).
Do not open the drive unit yourself. The drive unit is
maintenance-free and must be repaired only by quali-
fied experts and only with original spare parts.
This will
ensure that the safety of the drive unit is maintained. Unau-
thorised opening of the drive unit will void warranty claims.
All components mounted to the drive unit and all other
components of the eBike drive (e.g., the chainwheel,
chainwheel seat, pedals) may be replaced only against
identical components or components specifically ap-
proved for your eBike by the bicycle manufacturer.
This
protects the drive unit against overload and damage.
Remove the battery pack from the eBike before begin-
ning work (e.g. assembly, maintenance, work on the
chain, etc.) on the eBike, transporting it by car or
plane, or storing it.
Unintentional activation of the eBike
system poses a risk of injury.
The push-assistance function may only be used when
pushing the eBike.
Danger of injury when the wheels of
the eBike do not have ground contact while using the push-
assistance function.
Use only original Bosch battery packs approved for
your eBike by the manufacturer.
Using other battery
packs can lead to injuries and pose a fire hazard. When us-
ing other battery packs, Bosch shall not assume any liabil-
ity and warranty.
Do not make any modifications to your eBike system or
fit any other products which would be suitable for in-
creasing the performance of your eBike system.
This
normally reduces the lifetime of the system and risks dam-
age to the drive unit and the bike. There is also a risk of los-
ing the guarantee and warranty claims on the bike you have
purchased. By handling the system improperly you are al-
so endangering your safety and that of other road users,
thus running the risk of high personal liability costs and
possibly even criminal prosecution in the event of acci-
dents attributable to manipulation.
Please observe all national regulations on registering
and using eBikes.
Please read and observe the safety warnings and in-
structions enclosed in the operating instructions of the
battery pack as well as in the operating instructions of
your eBike.
Product Description and
Specifications
Intended Use
The drive unit is intended exclusively for your eBike and may
not be used for other purposes.
The eBike is intended for use on paved paths. It is not permit-
ted for use in competition.
Product Features
(See page 2
–
3)
The numbering of the components shown refers to the illus-
trations on the graphic pages at the beginning of the manual.
All illustrations of bike parts except for the drive unit, HMI in-
cluding operating unit, speed sensor and the corresponding
holders are schematic and may differ on your eBike.
1
Display-function button
“i”
2
Illumination button
3
HMI
4
Holder for HMI
5
HMI On/Off button
6 “RESET”
button
7
USB port
8
Protective cap of USB port
9
Drive unit
10
Operating unit
11
Display-function button
“i”
on the operating unit
12
Reduce value/scroll down button
“–”
13
Increase value/scroll up button
“+”
14
Push-assistance button
“WALK”
15
Lock latch for HMI
16
Locking screw for HMI
17
Speed sensor
18
Spoke magnet of the speed sensor
OBJ_BUCH-2074-001.book Page 1 Wednesday, August 14, 2013 12:19 PM