KAM KMD20 Instruction Manual - page 3

2 

6. Ventilation 

    The appliance should be situated so that it’s location or position does not interfere with it’s proper 

ventilation. For example, the appliance should not be situated on a sofa, bed, or similar surface that may block the 

ventilation opening; or keep the appliance away of those objects such as newspapers, carpet which may cover the 

ventilation opening or impede the flow of air through the ventilation opening. 

7.  Power Source & Power Cord 

    This appliance should be connected to a power supply only of the type described 

in these operating instructions, or marked on the unit.   

Be sure connect the appliance to a mains power socket which with a protective grounding connection. 

Power supply cord should be routed so that the are not likely to be walked upon or pinched by the items placed on or 

against them. When removing the cord from a power outlet be sure to remove it by holding the plug attachment and 

not by pulling on the cord.   

Check the total maximum power of your AC wall outlet and make sure it has the enough power to match the Power 

Consumption of this appliance, otherwise you could overload the wall outlet, which could cause fire.     

8.  Internal / External Voltage Selectors 

    Internal of external voltage selector switches, if any, should only be reset 

and re-equipped with a proper plug for alternative voltage by a qualified service technician . Do not attempt to alter 

this yourself. 

9.  Object & Liquid Entry 

    Take care to avoid any objects falling into or liquids are not spilled in to the inside of the 

appliance. 

10. Cleaning 

    Unplug the appliance first and clean only with a dry cloth. 

11. Non-use Period 

    The power cord of the appliance should be unplugged from the outlet when left unused for long 

periods of time. 

12. Unpacking & Setup 

  Please check your appliance for any damage after unpacking(before connecting) and 

contact your dealer in case of any related complains. Take care of choosing your installation place and the correct AC 

connection. If built in to a case, be aware that the depth and the weight of some kind appliance(such as Amplifier) 

does require an additional fixing on the backside or the use of rack shelf supports. Never mount the amplifier in a rack 

just by fixing it on the front plate – Manufacturer takes no responsibility in this case. 

13.  Damage Requiring Service 

    Servicing is required when the appliance has been damaged in any way, such as 

power cord or plug is damaged, liquid has been spilled or objects have fallen in the appliance, the appliance has been 

exposed to rain or moisture, does not operate normally, or has been dropped. Refer all servicing to qualified service 

personnel or contact your dealer. Do not attempt to repair by yourself. 

Characteristic: 

■  Ultra-low noise discrete Mic preamps with +48V phantom power. 

■  Additional multi-functional stereo channels .(MP6.4=4,MP8.2=2,MP12.2=2) 

■  Switchable 7-band graphic equalizer for ultimate main mix equalization. 

■  ALT 3-4 bus routable to main mix and control room with insert. 

■  Extremely high headroom-offering more dynamic range. 

■  Balanced inputs and main outputs for highest signal integrity. 

■  Ultra-musical 4-band EQ (stereo channels) and 3-band EQ. 

■  Switchable low-cut filter on all mono channels. 

■  AUX sends (pre/post)per channel 

■  FX sends (post)per channel, for internal or external effects and monitoring. 

■  Master AUX sends with gain control and PFL. 

■  Mute/ALT 3-4, solo-in-place and pre-fader-listen function on all channels. 

■  Separate main mix, ALT 3-4, control room and headphone outputs. 

■  2-track inputs assignable to main mix or control room/headphone outputs. 

■  Highly accurate 12-segment barograph meters. 

■  High quality 60mm faders and high quality sealed potentiometers.