1. DL manuals
  2. Kasda
  3. Wireless Router
  4. KW5212
  5. User Manual

Kasda KW5212 User Manual

Other manuals for KW5212: User Manual
Manual is about: Wireless VDSL Router

Summary of KW5212

  • Page 1

    \ kw5212 wlan vdsl router user manual.

  • Page 2

    Wlan vdsl router user manual notice this document contains proprietary information protected by copyright, and this manual and all the accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No part of this document may be photocopied or reproduced by mechanical,...

  • Page 3: Content

    Wlan vdsl router user manual content 1 overview ................................................................................................................................... 1 1.1 f eatures ...........................................................................................................

  • Page 4: 1 Overview

    Wlan vdsl router user manual 1 1 overview thank you for choosing our product. The product is a wireless vdsl router combining an vdsl modem, an 802.11n wireless router ,a 4-port switch and an usb port in one unit, bringing high-speed wireless internet connection to a home or office. 1.1 features 1.1...

  • Page 5

    Wlan vdsl router user manual 2  ip static routing  routing information protocol (rip, ripv2)  network address translation (nat)  virtual server, port forwarding  dynamic host configuration protocol (dhcp)  dns relay, ddns  igmp proxy  simple network time protocol (sntp)  vpn pass-through (i...

  • Page 6

    Wlan vdsl router user manual 3  dmz 1.1.7 management support  web based gui  upgrade or update via ftp/http  command line interface via telnet  diagnostic test  firmware upgradeable for future feature enhancement 1.1.8 operating system support  windows 98/98 se/me/2000/xp/vista/7  macintosh ...

  • Page 7

    Wlan vdsl router user manual 4 1.3 system requirements before using this router, verify that you meet the following requirements:  subscription for adsl service. Your adsl service provider should provide you with at least one valid ip address (static assignment or dynamic assignment via dial-up con...

  • Page 8: 2 Hardware Description

    Wlan vdsl router user manual 5 2 hardware description front panel led color function pwr green on: power on off: no power lan1,2,3,4 green on: lan link established and active via lan port blinking: dsl data activity occurs off: no lan link via lan port wlan green on: the wireless module is ready and...

  • Page 9

    Wlan vdsl router user manual 6 rear panel side panel wifi button: enable or disable wireless function. Reset button: system reset or reset to factory defaults. Wps button: a convenient way for wps set. Port function dsl connect the device to an dsl telephone jack or splitter using a rj-11 telephone ...

  • Page 10: 3  Hardware Installation

    Wlan vdsl router user manual 7 3 hardware installation this chapter shows you how to connect router. Meanwhile, it introduces the appropriate environment for the router and installation instructions. 1. Using a telephone line to connect the dsl port of router to the modem port of the splitter, and u...

  • Page 11

    Wlan vdsl router user manual 8 4 pc configuration guide 4.1 local pc configuration in windows 95, 98, me, xp,vista,7 1. In the windows task bar , click the “start” button, point to “settings”, and then click “control panel”. 2. Double- click the “network” icon. 3. On the “configuration” tab, select ...

  • Page 12

    Wlan vdsl router user manual 9 5 web-based management guide in order to use the web-based management software it will be necessary to use a computer that occupies the same subnet as the router. The simplest way to do this for many users will be to use dhcp server that is enabled by default on the ro...

  • Page 13

    Wlan vdsl router user manual 10 we can select wizard setup or advanced setup mode to setup kw5212.The wizard set up will guide us for a basic setting,and the advanced setup will guide us to home page for more detailed setup. 5.2 internet access configuration 5.2.1 adsl setup from home page, you can ...

  • Page 14

    Wlan vdsl router user manual 11 3. Click wan service from the left menu. 4. Click add to select a layer 2 interface for this service and then click next. 5. Choose wan service type, just choose pppoe for example here. You can enter your own service description here if you want and then click next. 6...

  • Page 15

    Wlan vdsl router user manual 12 pppoe service name can be blank unless your internet service provider gives you a value to enter. Authentication method is default to auto. It is recommended that you leave the authentication method in auto, however, you may select pap or chap if necessary. The defaul...

  • Page 16

    Wlan vdsl router user manual 13 enable full cone nat: in full cone nat, all requests from the same private ip address and port are mapped to the same public source ip address and port. Someone on the internet only needs to know the mapping scheme in order to send packets to a device behind the vdsl ...

  • Page 17

    Wlan vdsl router user manual 14 the gateway extends the ip subnet at the remote service provider to the lan computer. That is, the pc becomes a host belonging to the same ip subnet. The adsl gateway bridges the ip packets between wan and lan ports, unless the packet is addressed to the gateway's lan...

  • Page 18

    Wlan vdsl router user manual 15 9. Make sure that the settings below match the settings provided by your isp. Click on the apply/save button to save your configurations. 5.2.2 vdsl setup from home page, you can find advanced setup option on the left router configuration page. 1. From layer2 interfac...

  • Page 19

    Wlan vdsl router user manual 16 3. Click wan service from the left menu. 4.Click add to select a layer 2 interface for this service and then click next. 5. Choose wan service type, just choose pppoe for example here. You can enter your own service description here if you want and then click next. 6....

  • Page 20

    Wlan vdsl router user manual 17 pppoe service name can be blank unless your internet service provider gives you a value to enter. Authentication method is default to auto. It is recommended that you leave the authentication method in auto, however, you may select pap or chap if necessary. The defaul...

  • Page 21

    Wlan vdsl router user manual 18 someone on the internet only needs to know the mapping scheme in order to send packets to a device behind the vdsl device. The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the dial on demand check box and e...

  • Page 22

    Wlan vdsl router user manual 19 the gateway extends the ip subnet at the remote service provider to the lan computer. That is, the pc becomes a host belonging to the same ip subnet. The adsl gateway bridges the ip packets between wan and lan ports, unless the packet is addressed to the gateway's lan...

  • Page 23

    Wlan vdsl router user manual 20 9. Make sure that the settings below match the settings provided by your isp. Click on the apply/save button to save your configurations. 5.2.3 router mode setup 1. From advanced setup, click layer2 interface and select eth interface. Before you configure eth wan inte...

  • Page 24

    Wlan vdsl router user manual 21 5. From advanced setup, click wan service to configure a wan service over the interface you selected. 6. Click add and you ’ll see the following screen. 7. Click next and you ’ll see the following screen. Select pppoe as wan service type for example. Click next..

  • Page 25

    Wlan vdsl router user manual 22 8. Enter the user name and password that your isp has provided to you. Click next..

  • Page 26

    Wlan vdsl router user manual 23 pppoe service name can be blank unless your internet service provider gives you a value to enter. Authentication method is default to auto. It is recommended that you leave the authentication method in auto, however, you may select pap or chap if necessary. The defaul...

  • Page 27

    Wlan vdsl router user manual 24 pppoa and 1492 for pppoe. Do not change these values unless your isp asks you to. Enable full cone nat: in full cone nat, all requests from the same private ip address and port are mapped to the same public source ip address and port. Someone on the internet only need...

  • Page 28

    Wlan vdsl router user manual 25 server within the adsl gateway has only a single ip address to assign to a lan device. Napt and firewall are disabled when this option is selected. The gateway becomes the default gateway and dns server to the computer through dhcp using the lan interface ip address. ...

  • Page 29

    Wlan vdsl router user manual 26 11. Make sure that the settings below match the settings provided by your isp. Click on the apply/save button to save your configurations and reboot the adsl router..

  • Page 30

    Wlan vdsl router user manual 27 5.2.4 lan settings from lan, configure the dsl router’s ip address and subnet mask for lan interface. In this page, you can use dhcp (dynamic host configuration protocol) to control the assignment of ip addresses on your local network (lan only).Kw5212 support ipv4 /i...

  • Page 31

    Wlan vdsl router user manual 28 enable igmp snooping igmp snooping is a method that actually “snoops” or inspects igmp traffic on a switch. When enabled, the switch will watch for igmp messages passed between a host and a router, and will add the necessary ports to its multicast table, ensuring that...

  • Page 32

    Wlan vdsl router user manual 29 5.2.4.2 ipv6 lan settings item description ipv6 address this is the ip address that other devices on your local network will use to connect to the modem. Subnet mask this defines the size of your network. The default is 255.255.255.0. Enable igmp snooping igmp snoopin...

  • Page 33

    Wlan vdsl router user manual 30 use blocking mode to discard unknown multicast traffic. Disable / enable dhcp server the dhcp server assigns an ip addresses from a pre-set pool of addresses upon request from dhcp client (e.G. Your computer). Do not disable the dhcp server unless you wish to let anot...

  • Page 34

    Wlan vdsl router user manual 31 5.3 wireless setting 5.3.1 basic option description enable wireless a checkbox that enables or disables the wireless lan interfaces. The default is to enable wireless communications. Hide access point select hide access point to protect the adsl route access point fro...

  • Page 35

    Wlan vdsl router user manual 32 network name (ssid) enter a name for user’s wireless network here. Ssid stands for service set identifier. This name must be between 1 and 32 characters long. All wireless clients must either detect the gateway or be configured with the correct ssid to access the inte...

  • Page 36

    Wlan vdsl router user manual 33 4.Set wps ap mode as unconfigured and click config ap. 5. Set wps ap mode as configured and click save/apply. 6. Now you can use a wireless adaptor with wps function and the wps button to connect kw5212 to access the internet. 7. To configure security features for the...

  • Page 37

    Wlan vdsl router user manual 34 there are several security methods to choose from, depending on user’s needs and the capabilities of user’s wireless machines. Wep open and wep shared —wep is an encryption scheme that is used to protect user’s wireless data communications. Wep uses a combination of 6...

  • Page 38

    Wlan vdsl router user manual 35 wireless clients. The gateway rejects the login if the client's psk does not match. Wpa2 — wpa2 is a more advanced encryption method than wpa. Because it is a more recent standard, some of user’s wireless devices might not be able to use it. Wpa2 (psk) — this option u...

  • Page 39

    Wlan vdsl router user manual 36 3. Select “network printer” and click “next”. 4. Select connect to a printer on the internet, type “http://192.168.1.1:631/printers/printer” and click “next”. The printer name “printer” must be the same name entered in the adsl router “print server setting” as in step...

  • Page 40

    Wlan vdsl router user manual 37 5. Select driver file directory on cd- rom or in your hard disk and click “ok”. 6. Choose “yes” or “no” for default printer setting and click “next”. 7. Click “finish”. Appendix: frequent asked questions q: none of the leds are on when you power on the adsl router? A:...

  • Page 41

    Wlan vdsl router user manual 38 q: dsl led is in the circulation of slow-flashing and fast-flashing after connecting telephone line? A: this situation means the adsl router is in the status of failing to establish connection with central office. Please check carefully and confirm whether the adsl ro...

  • Page 42

    Wlan vdsl router user manual 39 what you collected from your service provider, re-configure adsl router and reboot it. If you still cannot work it out, you may need to verify these variables with the service provider. If the cause is not given above, please contact your local service provider!.