Kawasaki ZX-10R - 2010 Use And Care Manual - page 16
31
30
S
Se
eaalle
ed
d S
Su
urrffaacce
e B
Bu
urrn
ne
errss ((IIff aap
pp
plliiccaab
blle
e))
Wipe up spill-overs as soon as possible after they occur and before
they get a chance to burn in and cook solid. In the event of a spill-
over, follow these steps:
1. Allow the burner and grate to cool to a safe temperature level.
2. Lift off the burner grates.
3. Remove teh burner cap and clean per instructions below.
4. Wipe up any spills which remains on the sealed top surface.
5. Wash grates and burner caps in hot, soapy water and rinse clean.
6. Replace burner cop and grate after drying thoroughly.
If ports on the open or sealed burners are clogged, clean with a
straight pin. Do not enlarge or distort the ports. Do not use a
toothpick to clean the ports. When replacing burner caps, carefully
align the tabs underneath the cap with the outside edge of burner.
Make sure the tabs are not aligned with the igniter and the burner cap
is level.
S
Se
eaalle
ed
d B
Bu
urrn
ne
err A
Allu
um
miin
nu
um
m B
Baasse
e ((IIff aap
pp
plliiccaab
blle
e))
The aluminum base should be wiped regularly withhot soapy water at
the end of each cooling period. D
DO
O N
NO
OT
T use steel wool, abrasive
cloths, cleanser, or powders. To remove encrusted materials, soak the
area with a hot towel to loosen the material, then use a wooden nylon
spatula. D
DO
O N
NO
OT
T use a metal knife, spatula, or any other metal tool to
scrape the aluminum base. N
NO
OT
TE
E: For stubborn stains, use a non
abrasive cleanser such as Bon Ami
TM
and a soft brush or soft Scoth
Brite
TM
pad.
B
Bu
urrn
ne
err C
Caap
pss
The surface burner caps should be routinely removed and cleaned.
Always clean the burner caps after a spill over. Keeping the burner
caps clean will prevent improper ignition and uneven flames. To clean,
pull burner cap straight up from the burner base. Wipe off surface
burner caps with warm, soapy water and a soft cloth after each use.
Use a a non-abrasive cleanser such as Bon Ami and a soft brush or soft
scotch brite
TM
pad for cooked-on foods. Dry thoroughly after cleaning.
For best cleaning and to avoid possible rusting, do not clean in
dishwasher or self-cleaning oven.
C
Co
on
nttrro
oll K
Kn
no
ob
bss
MAKE SURE THE CONTROL KNOBS POINT TO THE OFF POSITION
BEFORE REMOVING. Pull the knobs straight off. Wash in detergent
and warm water. Do not soak knobs. Dry completely and replace by
pushing firmly onto stem. DO NOT USE any cleaners containing
ammonia or abrasives. They could remove the graphics from the knob.
C
Co
on
nttrro
oll P
Paan
ne
ell
D
DO
O N
NO
OT
T U
US
SE
E aan
nyy cclle
eaan
ne
errss cco
on
nttaaiin
niin
ng
g aam
mm
mo
on
niiaa o
orr aab
brraassiivve
ess. They
could remove the graphics from the control panel. Use hot, soapy
water and a soft clean cloth.
W
Wo
okk C
Caasstt IIrro
on
n B
Bu
urrn
ne
err ((IIff aap
pp
plliiccaab
blle
e))
For proper lighting and performance of the burner, keep the
electric igniter and burner ports clean. It is necessary to clean these only
when the flame does not burn blue completely around all rings of the
burner, when there is a severe spillover or when the burner does not
light, even though the electric spark igniter sparks. Clean the burner by
scraping off burned on food soil. Use a wire, a straightened paper clip,
or needle to clean the ports. D
Do
o n
no
ott u
usse
e aa tto
oo
otth
hp
piicckk;; iitt cco
ou
ulld
d b
brre
eaakk o
offff
iin
n tth
he
e p
po
orrtt.. B
Be
e ssu
urre
e tth
he
e vve
en
nttu
urrii ttu
ub
be
e rre
em
maaiin
nss d
drryy..
Burner
ports
Venturi tube