Summary of Christineberg
Page 1
Christineberg installation instructions care and firing instructions.
Page 2: Contents
Contents general information ......................................................................................................................................... 1 important points .....................................................................................................................
Page 3: General Information
General information we congratulate you on your choice of tile stove. Christineberg is a new type of tile stove with a unique design. It has been developed and designed to take advantage of modern combustion and heat accumulation technology. The shape originates from 18th century sweden. The christi...
Page 4: Prerequisites
Prerequisites - 2 - building notice when you install a stove and erect a chimney, you need to contact the planning and building committee in your municipality for up-to-date information. Distance to flammable structural units before deciding where to place the tile stove, you must localise the beams...
Page 5: Preparations
Preparations - 3 - 1a corner wall installation there are two different alternatives for connecting the flue: • rear installation (turnable) • top installation (straight up) the height from the floor to the centre of the flue at the rear is 1920 mm. 1b flush wall installation there are two different ...
Page 6: Installation Instructions
- 4 - installation instructions before starting on the installation of the tile stove, the following steps need to be fully completed: • chimney: alternative 1 - an existing chimney prepared for rear connection alternative 2 - a newly installed chimney prepared for rear connection alternative 3 - pr...
Page 7
- 5 - 4. Put in six element 3 pieces with matching gaskets, note the vertical gasket. Place round gasket spacers evenly distributed on all sides, four spacers per course, twelve pieces in total. Push the elements outwards against the safety case, so the spacers are kept in place. 6. Put in the heart...
Page 8
- 6 - 8. Install the two upper horizontal side walls on each side of the hearth, in the same way as the lower ones. 9. Put in the two vertical side walls, with the two holes downwards and the chamfer facing forward. Arrow 7. Push them backwards, into the groove, until they make contact. Arrow 8. Tur...
Page 9
- 7 - 12. Install element 6 right way round with matching gas- ket and four gasket spacers, in the same way as element 5. Also install one element 7 right way round with match- ing gasket, but wait with the gasket spacers. They are installed first in step 14. 13. Apply a string of silicone (red) aro...
Page 10
- 8 - 15. Install the plate cover with silicone (red) in between. Check the joint is sealed all round. 16. Press in the short thick fireproof rope seal between the hearth's bottom plate and the lower edge of the cast iron frame. Apply a string of silicone (red) around the hole for the air intake in ...
Page 11
- 9 - 18. Carefully push out the half-arc-shaped cardboard strip from the template, in which the tile base is to be assembled. Assemble the base on some blobs of silicone (transpar- ent) and with adhesive between the tiles in the numerical order shown in the overview. Make sure that the joints betwe...
Page 12
- 10 - 20. Assemble tile course 2 in adhesive. The middle joint for tiles 1 and 3 must line up with the tile moulding's joint. The inside of the tiles must be in line with the inside of the tile moulding. Fix using tape. Note that tiles and 1 and 3 have chamfered front edges. ( specially cut to fit ...
Page 13
- 11 - 24. Assemble tile course 6 in adhesive. Make sure that the hole for the damper shaft is in the right place. 25. Now the flue gas damper (consisting of a damper box and a damper blade) and the chimney connection sleeve have to be installed. Begin by applying silicone (red) around the edge of t...
Page 14
- 12 - 27. Screw a nut on top of the wing nut on the three front stud bolts that keep the cover down and add washers. Adjust the nuts so the top edge of each washer is at the same height as the course of tiles. Then thread on the three plate brackets and adjust them so that they cover approximately ...
Page 15
- 13 - 29. Assemble tile course 8 (the wide, upper, tile mould- ing) in adhesive. The joint between tiles 1 and 2 must be in line with the tile joint in the course below. Do not fire your christineberg for at least one week after completing the installation to allow for the hardening times. The firs...
Page 16: Care & Firing Instructions
Care & firing instructions the christineberg has been tested by the swedish national testing and research institute. The test results show a very pure combustion and a useful efficiency of not less than 86%. Both the useful efficiency and the environmental results make the christineberg directly com...
Page 17
Also read our warranty terms, which were included in the delivery. If you have questions, you are welcome to contact us. We wish you many pleasant and rewarding years with your christineberg tile stove - an investment that combines use with pleasure. - 15 - firing and refilling with wood open a wind...
Page 18: Technical Specification
Technical specification - 16 - dimensions and performance • height 2265 mm • width 695 mm • depth 600 mm • weight 600 kg • height to centre of rear connection 1920 mm • height to centre of top connection 1920 mm • output over 10 kw • efficiency 86% • cooling time up to 24 hours the christineberg fro...
Page 20
01/03/2012 www.Keddy.Se.