Summary of KCT27036A
Page 1
Heat pump hot water system installation manual.
Page 2
2 contents kelvinator heat pump hot water system congratulations and thank you for choosing our heat pump hot water system. Before you install the hot water system, we recommend that you read through the entire installation manual, which provides instructions on the safe installation of the hot wate...
Page 3
Kelvinator heat pump hot water system important safety instructions 3 this installation manual has been prepared for installers and service technicians of the equipment. Please keep it in a safe place for future reference. For the installer the installation must be completed by suitably licensed ins...
Page 4
4 heat pump specifications kelvinator heat pump hot water system heat pump specifications kse362hpca heat pump dimensions ( w x h x d) in mm 790 x 765 x 275 heating capacity (kw) condition 1* 4.30 standard power (kw) 1.25 heating capacity (kw) condition 2* 4.70 standard power (kw) 1.39 heat pump cir...
Page 5
Kelvinator heat pump hot water system storage tank specifications 5 storage tank specifications model number kct27036a kct27036b kct34036a kct34036b kct42536b diameter (mm) - a 650 600 650 700 700 height (mm) - b 1390 1675 1690 1520 1785 electrical connection height (mm) - c 580 750 680 700 850 cold...
Page 6
6 components kelvinator heat pump hot water system components supplied with tank: kct27036a, kct27036b, kct34036a, kct34036b, kct42536b item no. Quantity image description 1 1 of kct27036a - 270l tank with 3.6kw element kct27036b - 270l tank with 3.6kw element kct34036a - 340l tank with 3.6kw elemen...
Page 7
Kelvinator heat pump hot water system components 7 components supplied with heat pump: kse362hpca item no. Quantity image description 4 1 kse362hpca - heat pump module 5 1 sensor wire 6m 6 1 sensor pocket assembly 7 4 rubber mounting feet 8 1 rubber seal for drain spigot 9 1 drain spigot supplied wi...
Page 8
8 installation kelvinator heat pump hot water system installation of the heat pump hot water system shall be completed in accordance with the as/nzs 3500.1 and as/ nzs 3500.4 plumbing codes regarding water and hot water supply as well as local authority regulations and any other applicable australia...
Page 9
Kelvinator heat pump hot water system installation 9 placing of heat pump and storage tank the heat pump and storage tank must be installed on a level surface and checked with a spirit level. The storage tank in particular must be level to ensure the correct positioning of the anode inside the tank ...
Page 10
10 installation kelvinator heat pump hot water system heat pump connections the heat pump can be installed up to 5 metres away from the storage tank (only 1 meter of hose is supplied). If the heat pump is to be installed further than 1m away, run hard copper piping from the tank to a point near the ...
Page 11
Kelvinator heat pump hot water system installation 11 filling with water and dispelling air from the system at this stage the wiring to the hot water system should either be disconnected at the switchboard or have the power isolated to it (off). Once all plumbing connections have been made to the ho...
Page 12
12 installation diagram kelvinator heat pump hot water system installation diagram uncontrolled hot water outlet (kitchen, laundry) refer to local electrical requirements to ascertain whether isolation switch is required under heat pump (drain assembly viewed from back of unit) – discharge condensat...
Page 13
Tempered (50°c) hot water outlet (bathrooms) tempering valve 20mm diameter conduit cold water expansion control valve (700kpa) may be required refer to local plumbing guidelines kelvinator heat pump hot water system installation diagram 13 relief valve relief valve outlet drain earth terminal return...
Page 14
14 electrical connection kelvinator heat pump hot water system electrical wiring the heat pump hot water system must be installed in accordance with the as/nzs 3000 wiring rules, the local electrical authority regulations and any other applicable standards. The pipe work, storage tank and heat pump ...
Page 15
Kelvinator heat pump hot water system electrical connection 15 electrical connection wiring the heat pump on a continuous power supply only: if the heat pump is to be wired to a continuous power supply only, the jumper leads supplied with the heat pump are to be installed. The red jumper lead is to ...
Page 16
16 electrical connection kelvinator heat pump hot water systems wiring the hot water system to the switchboard: the hot water system is required to be connected to the earthing system of the premises and to the earth stake. Each earth wire is to be wired to the earthing terminal inside the switchboa...
Page 17
Kelvinator heat pump hot water system temperature sensor connection 17 installing the temperature sensor in the storage tank the copper end of the sensor cable is the temperature sensing device and is to be installed in the sensor pocket located at the “return” connection on the storage tank. When i...
Page 18
18commissioning kelvinator heat pump hot water system 3. Once the heat pump has stopped and the tank is up to temperature, drain some water off using a hot tap inside and then operate the auxiliary boost button. Monitor and confirm the operation of the tank element and thermostat. 4. Once the hot wa...
Page 19
Kelvinator heat pump hot water system warranty 19 this document sets out the terms and conditions of the product warranties for electrolux appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should you require service for...
Page 20
P/no. Khwhpi/2 © 2015 electrolux home products pty ltd abn 51 004 762 341 kman_khwhpim_oct15 if you’d like further information about kelvinator appliances, please visit your retailer, phone or email our customer care team or visit our website. Telephone: 13 62 26 email: hotwatersystems@electrolux.Co...