Kelvinator KICB320HWF Instruction Booklet - page 3
13
Türanschlagwechsel
Bevor Sie nachstehende Arbeitsvorgänge
durchführen, Netzstecker unbedingt aus der
Steckdose ziehen!
Den Wechsel auf folgende Weise ausführen:
1.Entlüftungsgitter (D) abnehmen.
2.Unteres Scharnier (E) abnehmen.
3.Untere Tür vom mittleren Scharnier (H) abheben
und Scharnier abschrauben.
4.Obere Tür vom oberen Stift (G) abnehmen.
5.Nachdem Sie die Stöpsel entternt haben, die auf
der gegenüberliegenden Seite wieder
einzusetzen sind, nehmen Sie den oberen Stift
ab und montieren Sie ihn an der
gegenüberliegenden Seite.
6.Obere Tür wieder einsetzen.Mittleres Scharnier
an gegenüberliegende Seite montieren.
7.Untere Tür wieder einsetzen.
8.Mit Hilfe eines 10 mm Schlüssel den unteren
Scharnierstift abschrauben und auf
gegenüberliegenden Scharnierseite wieder
anschrauben.
9.Unteres Scharnier (E) auf gegenüberliegende
Türseite montieren und mittels der vorher
entnommenen Schrauben befestigen.Abdeckung
(F) vom Entlüftungsgitter (D) herausschieben und
auf gegenüberliegende Seite montieren.
10.Entlüftungsgitter wieder einsetzen.
Zur Ausrichtung der Türen kann man auf das mittlere
Scharnier wirken.
Das mittlere Scharnier ist nach dem Lösen der
beiden Schrauben mit Hilfe einer Vorrichtung
horizontal regulierbar.
Achtung
Vergewissern Sie sich nach Ausführung des
Anschlagwechsels der Türen, daß alle Schrauben
fest angezogen sind und überprüfen Sie auch,
ob die Magnetdichtung am Möbel perfekt anliegt.
Bei einer niedrigen Raumtemperatur (z.B. im
Winter) kann es vorkommen, dass die Dichtung
nicht perfekt am Schrank haftet. Die
Wiederherstellung der Dichtung erfolgt
automatisch nach gewisser Zeit. Wollen Sie aber
diesen Prozess beschleunige, so genögt es die
Dichtung mit einem Fön zu erwärmen.
G
H
F
D
PR18
F
F
F
E
E
I
I
I
48
Changing the opening direction of
the doors
Before carrying out any operations, remove the plug
from the power socket.
To change the opening direction of the door,
proceed as follows:
1.pull off the ventilation grille (D) which is clipped
into place;
2.remove the bottom hinge (E) by unscrewing its
fixing screws;
3.remove the lower door, sliding it out of the middle
hinge;
4.unscrew the middle hinge (H);
5.remove the upper door, releasing it from the
upper pin (G);
6.unscrew the upper pin (G) and refit it on the
opposite side;
7.remove the two plugs of the door (where
available), discovering the holes for the hinge
pins, assemble them on the opposite side and
refit the upper door;
8.reassemble the middle hinge on the opposite
side;
9.reassemble the lower door;
10.using a 10 mm spanner, unscrew the hinge pin
(E) and reassemble it on the opposite side of the
hinge;
11.reassemble the lower hinge (E) on the opposite
side, using the screws previously removed.Slide
the hole cover (F) out of the ventilation grille (D)
by pushing it in the direction of the arrow and
reassemble it on the opposite side;
12.refit the ventilation grille (D), clipping it into
place.
To line up the doors, it is possible to adjust the
middle hinge (H) horizontally by means of a tool,
after slackening the two screws (see figure).
Warning:
After having reversed the opening direction of
the doors check that all the screws are properly
tightened and that the magnetic seal adheres to
the cabinet. If the ambient temperature is cold (i.e.
in Winter), the gasket may not fit perfectly to the
cabinet.In that case, wait for the natural fitting of the
gasket or accelerate this process by heating up the
part involved with a normal hairdrier.
G
H
F
D
PR18
F
F
F
E
E
I
I
I