Kemppi Minarc 120 AU Operating Manual

Other manuals for Minarc 120 AU: Operating Manual

Page of 22

Download

Print this page

Bookmark us

Käyttöohje • Suomi

Bruksanvisning • Svenska

Bruksanvisning • Norsk

Brugsanvisning • Dansk

Operating manual • English

Gebrauchsanweisung • Deutsch

Gebruiksaanwijzing • Nederlands

Manuel d’utilisation • Français

Manual de instrucciones • Español

Instrukcja obsługi • Polski

Инструкции по эксплуатации • По-русски

1910150

0901

INARC™

150, 151

150 VRD

120 AU, 150 AU

1 2 3 4 5 6 7 Next › »

Summary of Minarc 120 AU

Page 1
Käyttöohje • suomi bruksanvisning • svenska bruksanvisning • norsk brugsanvisning • dansk operating manual • english gebrauchsanweisung • deutsch gebruiksaanwijzing • nederlands manuel d’utilisation • français manual de instrucciones • español instrukcja obsługi • polski Инструкции по эксплуатации •...
Page 4: Contents
En contents 1. Preface ....................................................... 3 1.1 introduction ......................................................................................................... 3 1.2 safety instructions .........................................................................
Page 5: Preface
En 1. Preface 1.1 introduction congratulations on having purchased a kemppi product. Properly installed and used kemppi products should prove to be productive machines requiring only a small amount of regular maintenance. This manual is arranged to give you a good understanding of the equipment and ...
Page 6: Spatter and Fire Safety
En • never wear the device on the shoulder during welding and never suspend it by the carrying strap during welding. • do not expose the machine to high temperatures, as heat may cause damage to the machine. • keep the torch cable and earthing cable as close to each other as possible throughout thei...
Page 7: Welding Power Circuit
En • make sure that faulty and damaged welding torches are changed immediately as they can be lethal and may cause electrocution or fire. • remember that the cable, plugs and other electric devices may be installed or replaced only by an electrical contractor or engineer authorised to perform such o...
Page 8: Disclaimer
En • always store the machine in a dry and clean space. • protect the machine from sand and dust during use and in storage. • the recommended operating temperature range is -20 to +40 °c. The machine’s operation efficiency decreases and it becomes more prone to damage if used in temperatures in exce...
Page 9: 1.3
En 1.3 product introduction kemppi minarc is a manual metal arc welding machine, small in size, suitable for industry, site and repair welding. The unit uses one phase connection voltage and it is manufactured for two different mains voltages: 230 v (minarc 150) and 110 v (minarc 151). Minarc 150vrd...
Page 10: 2.2
En 2.2 placing the unit place the unit on horizontal, solid and clean surface. Shield it from heavy rain and scorching sun. Make sure that cooling air circulates freely. 2.3 serial number serial number of the unit is marked on the rating plate of the unit. The serial number makes it possible to trac...
Page 11: 2.5
En 1 2 3 4 5 6 7 8 2.5 connecting to power supply mains the unit has a mains cable and a wall plug (note! Minarc 151 (110 v) is delivered without a plug). You can find fuse and cable sizes in the end of these instructions in technical data. 2.6 filler materials and equipment see also 2.4. Main compo...
Page 12: Use
En 3. Use note! It is forbidden to weld in places where there is a danger of fire or explosion! 3.1 welding processes 3.1.1 manual metal arc welding (mma) in manual metal arc (mma) the welding filler material is melted from the electrode to the weld pool. Rate of welding current is selected on the b...
Page 13: Inarc
En on ics tm a 10 20 40 60 80 100 120 140 m inarc ø 1,6 ø 2,0 ø 2,5 ø3,25 fe-rutile 30-60 40-80 50-110 80-140 fe-basic 30-55 50-80 80-110 110-140 1 3 2 4 5 6 main switch and signal light when you turn the main switch to position i, signal light is lit and the unit is ready for welding. Signal light ...
Page 14: 3.3
En 3.3 welding selections 3.3.1 manual metal arc welding (mma) select welding parameters according to filler manufacturer’s recommendations. 1. Select polarity (+ or -) of welding current cable and return current cable according to filler. 2. Select mma welding with the switch . 3. Select suitable w...
Page 15: 3.5
En arc is lit move the electrode slowly forwards tilting it to appr. 10-15° pulling angle. If necessary, adjust current value. Shielding gas is used in dc tig welding. Your dealer will give you advice on choosing gas and equipment. Open the gas valve on the ttm 15v tig torch. When gas starts to flow...
Page 16: 4.2
En 4.2 troubleshooting problem cause the main switch indicator will not light up no electricity connected to the machine • check the mains supply fuses. • check the mains cable and plug. Poor welding result several factors affect the welding quality. • check that the earthing clamp is firmly attache...
Page 17: Ordering Numbers
En 6. Ordering numbers item ordering number minarc 150 welding machine (includes earth- and welding cables) 6102150 minarc 150 welding machine (denmark) (includes earth- and welding cables) 6102150dk minarc 151 welding machine (includes earth- and welding cables) 6101151 minarc 120au welding machine...
Page 18
En welding range mma 10 a/20,5 v - 140 a/25,6 v 10 a/20,5 v - 140 a/25,6 v tig 5 a/10 v - 150 a/16 v 5 a/10 v - 150 a/16 v welding current control stepless stepless open-circuit voltage 85 v, (vrd 30 v) 85 v idle power power factor 0,60 0,60 efficiency 80 % 80 % electrode sizes to be welded, diamete...
Page 19
En welding range mma 10 a/20,5 v - 110 a/24,4 v 10 a/20,5 v - 140 a/25,6 v tig 5 a/10 v - 120 a/15 v 5 a/10 v - 150 a/16 v welding current control stepless stepless open-circuit voltage 30 v 30 v idle power power factor 0,60 0,60 efficiency 80 % 80 % electrode sizes to be welded, diameter Ø 1,5-2,5 ...
Page 20: Warranty Policy
En 8. Warranty policy kemppi oy provides a warranty for products manufactured and sold by the company if defects in materials or workmanship occur. Warranty repairs are to be carried out only by an authorised kemppi service agent. Packing, shipping, and insurance are at the orderer’s expense. The wa...
Page 22: Www.Kemppi.Com
Www.Kemppi.Com kemppi oy pl 13 fin-15801 lahti finland tel +358 3 899 11 telefax +358 3 899 428 www.Kemppi.Com kemppikoneet oy pl 13 fin-15801 lahti finland tel +358 3 899 11 telefax +358 3 734 8398 e-mail: myynti.Fi @kemppi.Com kemppi sverige ab box 717 s-194 27 upplands vÄsby sverige tel +46 8 590...