Küppersbusch EKV6750.OJ Instructions For Use And Installation - page 10
10
Setting water hardness
The operating period can be extended if required, making descaling less frequent by program-
ming the machine on the basis of the real lime content in the water used.
Proceed as follows:
• remove the “Total Hardness Test” strip (attached to page 2) from its packaging then dip it
fully in the water for a few seconds,
Then remove and wait about 30 seconds (until it changes colour and forms red squares).
• turn the appliance on by pressing the ON/OFF/stand-by button (A7).
• Press the
icon (B2) to enter the menu and then the
icons (B7) and (B8) until
“WATER HARDNESS” is displayed.
• Press the OK icon (B9).
• Press the
icons (B7) and (B8) until the number coincides with the number of red
squares on the test strip (for example, if there are 3 red squares on the test strip, select the
message “WATER HARDNESS 3”
• Press the OK icon (B9) to confirm.
The coffee maker is now programmed to provide the descale warning when actually neces-
sary.
Programming coffee
For instructions on programming coffee, see the “CHANGING THE QUANTITY OF COFFEE IN THE
CUP” section.
Programming cappuccino
For instructions on programming cappuccino, see the section “CHANGING THE QUANTITY OF MILK
AND COFFEE FOR CAPPUCCINO”.
Programming water
For instructions, see the “CHANGING THE QUANTITY OF HOT WATER” section.
Descaling
Important!
Respect the safety warnings provided by the manufacturer and given on the descaler pack.
N.B.:
Use the descaler recommended by the manufacturer only.
Use of other descalers invalidates the guarantee.
Failure to descale the appliance as described also invalidates the guarantee.
When “PLEASE DESCALE !” is displayed, the machine requires descaling.
Proceed as follows:
• make sure the machine is ready;
• Press the
icon (B2) to enter the menu and then the
icons (B7) and (B8) until
“DESCALE” is displayed.
• Press the OK icon (B9).
The message “ADD DESCALER PLEASE CONFIRM” is displayed.
• Empty the tank of water, pour the contents of the descaler bottle into the tank respecting
the instructions given on the descaler pack, then add water..
Position a container with a capacity of 2 litres under the hot water spout.
• Press the OK icon (B9). Descaler flows out of the hot water spout into the container below.
The appliance displays: “DESCALING”.
• The descale programme automatically performs a series of deliveries and pauses.
• After about 30 minutes “DESCALE COMPLETE PLEASE CONFIRM” is displayed.
• Press the OK icon (B9). “RINSING FILL TANK” is displayed.
• Empty the water tank, rinse to eliminate descaler residues, then fill with clean water.
• Replace the tank full of clean water.
“RINSING PLEASE CONFIRM” is displayed again.
• Press the OK icon (B9) again.
Hot water flows out of the spout into the container below and “RINSING” is displayed.
• Wait until “RINSING COMPLETE PLEASE CONFIRM” is displayed.
• Press the OK icon (B9).
“DESCALE COMPLETE” is displayed, then “FILL TANK!”.
Fill the tank again with clean water.
• The descale programme is now terminated and the appliance is ready to make coffee again.
NOTE: If descaling is interrupted before completion, the process must be begun again from
the beginning.
Important!
FAILURE TO DESCALE THE APPLIANCE REGULARLY INVALIDATES THE GUAR-
ANTEE.
Resetting default values (reset)
If you change the original values, the default values can be reset as follows:
• Press the
icon (B2) to enter the menu and then the
icons (B7) and (B8) until
“RESET TO DEFAULT” is displayed.
• Press the OK icon (B9) and the appliance displays “RESET TO DEFAULT PLEASE CONFIRM”.
• press the OK button (B9) to reset the default values;
Statistics
This displays statistics relating to the machine.
To display, proceed as follows:
• Press the
icon (B2) to enter the menu and then the
icons (B7) and (B8) until
“STATISTICS” is displayed.
• Press the OK icon (B9).
• Press the
icons (B7) and (B8) to verify:
• How many coffees and cappuccinos have been made.
• How many times the machine has been descaled.
• How many cappuccinos have been made;
• The total number of litres of water delivered.
• Press the ESC icon (B6) once to exit the function or twice to exit the menu.
Buzzer
This activates or deactivates the buzzer emitted by the machine each time an icon is pressed or
an accessory is inserted/removed.
N.B.:
The buzzer is active by default.
•
Press the
icon (B2) to enter the menu and then the
icons (B7) and (B8) until
“BUZZER” is displayed.
• Press the OK icon (B9). “BUZZER PLEASE CONFIRM” is displayed.
• Press the ESC (B6) icon (B6) to disable or the OK icon (B9) to enable the buzzer.
• Press the ESC (B6) icon (B6) to exit the menu.
Adjusting contrast
To increase or reduce the contrast of the display, proceed as follows:
• Press the
icon (B2) to enter the menu and then the
icons (B7) and (B8) until
“CONTRAST” is displayed.
• Press the OK icon (B9).
• Press the
icons (B7) and (B8) until the required display contrast is reached. The pro-
gressive bar indicates the level of contrast selected.
• Press the OK icon (B9) to confirm.
• Press the ESC (B6) icon (B6) once to exit the function or twice to exit the menu.
TURNING THE APPLIANCE OFF
Each time the appliance is turned off, it performs an automatic rinse cycle which cannot be in-
terrupted.
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts.
Avoid contact with splashes of water.
To turn the appliance off, press the ON/OFF button (A7).
The appliance performs the rinse cycle then goes off.
N.B.!
If the appliance is not used for an extended period, place the main switch on the
back of the appliance in the 0 position (A23).
TECHNICAL SPECIFICATION
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1350 W
Pressure: 15 bars
Water tank capacity: 1.8 litres
Size LxHxD: 594x 455x411 mm
Weight: 23/24 kg
The appliance complies with the following EC directives:
• EC Regulation 1275/2008 for standby.