Küppersbusch EKV6750.OJ Instructions For Use And Installation - page 8
8
• Select the quantity of milk required by pressing the
icons (B7) and (B8). The pro-
gress bar shows the quantity of milk selected.
• Press the OK icon (B9) to confirm (or the ESC icon (B6) to cancel the operation.
• Press the ESC (B6) icon (B6) (fig. 18) twice to exit the menu.
Changing the quantity of coffee
• Press the
(B2) icon (B2) to enter the menu (fig. 15), then press the
icons (B7)
and (B8) (fig. 2) until “PROGRAM CAPPUCCINO” is displayed.
• Press the OK icon (B9) to confirm then the
icons (B7 and (B8) (fig. 2) until “COFFEE
FOR CAPPUCC.” is displayed.
• Press the OK icon (B9) again.
• Select the quantity of coffee required by pressing the
icons (B7) and (B8). The pro-
gress bar shows the quantity of coffee selected.
• Press the OK icon (B9) to confirm (or the ESC icon (B6) to cancel the operation.
• Press the ESC icon (B6) (fig. 18) twice to exit the menu.
CLEANING
Cleaning the coffee maker
Do not use solvents or abrasive detergents to clean the coffee maker. A soft damp cloth will
suffice.
Never wash any of the components of the coffee maker in the dishwasher.
The following parts of the machine must be cleaned regularly:
• Waste coffee container (A4).
• Drip tray (A14).
• Water tank (A12).
• Coffee spouts (A13)
• Pre-ground coffee funnel (A21).
• nside of the machine, accessible after opening the service door (A2).
• Brewing unit (A5).
Cleaning the waste coffee container
When “EMPTY WASTE COFFEE CONTAINER” is displayed, the waste coffee container must be emp-
tied and cleaned.
To clean:
• open the service door on the front of the appliance (fig. 16), extract the drip tray (fig. 17)
and clean.
• Clean the waste coffee container thoroughly.
Important!
When extracting the drip tray, the waste coffee container
must
always
be emptied.
Cleaning the drip tray
Important!
If the drip tray is not emptied the water might overflow.
This could damage the machine.
The drip tray is fitted with a level indicator (red) showing the level of water it contains (fig. 28).
Before the indicator protrudes from the cup tray, the drip tray must be emptied and cleaned.
To remove the tray:
1. Open the service door (fig. 16).
2. Remove the drip tray and the waste coffee container (fig. 17).
3. Clean the drip tray and waste coffee container (A4).
4. Replace the drip tray and waste coffee container (A4).
5. Close the service door.
Cleaning the water tank
1. Clean the water tank (A12) regularly (about once a month) with a damp cloth and a little
mild washing up liquid.
2. Remove all traces of washing up liquid.
Cleaning the spouts
1. Clean the nozzles periodically using a sponge.
2. Check regularly that the holes in the coffee spout are not blocked.
If necessary, remove coffee deposits with a toothpick (fig. 27).
Cleaning the pre-ground coffee funnel
• Check regularly (about once a month) that the pre-ground coffee funnel is not blocked (fig.
21).
Danger!
Before performing any cleaning operations, the machine must be turned off
by pressing the main switch (A23) and unplugged from the mains power supply.
Never immerse the coffee maker in water.
Cleaning the inside of the coffee maker
1. Check regularly (about once a week) that the inside of the appliance is not dirty.
If necessary, remove coffee deposits with a sponge.
2. Remove the residues with a vacuum cleaner (fig. 30).
Cleaning the brewing unit
The brewing unit must be cleaned at least once a month.
Important!
The brewing unit (A5) must not be removed when the appliance is on.
Do not use force to remove the brewing unit.
1. Make sure the machine is correctly turned off (see “Turning the appliance off”).
2. Open the service door (fig. 16).
3. Remove the drip tray and waste coffee container (fig. 17);
4. Press the two red release buttons inwards and at the same time pull the brewing unit out-
wards (fig. 31).
Important!
Do not use washing up liquid to clean the brewing unit. It would remove
the lubricant applied to the inside of the piston.
5. Soak the brewing unit in water for about 5 minutes, then rinse.
6. After cleaning, replace the brewing unit (A5) by sliding it onto the internal support and pin
at the bottom, then push the PUSH symbol fully in until it clicks into place.
Support
Pin
N.B.:
If the brewing unit is difficult to insert, you must first adapt it to the right dimen-
sions by pressing it forcefully from the bottom and top as shown in the figure.
7. Once inserted, make sure the two red buttons have snapped out.
8. Replace the drip tray and waste coffee container.
9. Close the service door.
Cleaning the milk container
Important!
Always clean the tubes inside the milk container (C) when you prepare
milk.
If there is still milk in the container, do not leave it out of the refrigerator for longer than strictly
necessary.