1. DL manuals
  2. KUSSMAUL
  3. Air Compressor
  4. Auto-Pump 091-9B-220
  5. Instruction Manual

KUSSMAUL Auto-Pump 091-9B-220 Instruction Manual

Manual is about: 220/240 VAC

Summary of Auto-Pump 091-9B-220

  • Page 1

    Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....

  • Page 2: Note

    Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...

  • Page 3: Caution

    Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.

  • Page 4

    Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...

  • Page 5: Warranty.

    Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...

  • Page 6

    Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...

  • Page 7

    Template auto pump 3.50 4.75 7/32 dia. Holes 4places.

  • Page 8

    Spare parts layout auto pump.

  • Page 9

    Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...

  • Page 10: Auto-Pump

    Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....

  • Page 11: Note

    Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...

  • Page 12: Caution

    Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.

  • Page 13

    Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...

  • Page 14: Warranty.

    Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...

  • Page 15

    Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...

  • Page 16

    Template auto pump 3.50 4.75 7/32 dia. Holes 4places.

  • Page 17

    Spare parts layout auto pump.

  • Page 18

    Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...

  • Page 19: Auto-Pump

    Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....

  • Page 20: Note

    Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...

  • Page 21: Caution

    Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.

  • Page 22

    Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...

  • Page 23: Warranty.

    Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...

  • Page 24

    Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...

  • Page 25

    Template auto pump 3.50 4.75 7/32 dia. Holes 4places.

  • Page 26

    Spare parts layout auto pump.

  • Page 27

    Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...

  • Page 28: Auto-Pump

    Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....

  • Page 29: Note

    Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...

  • Page 30: Caution

    Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.

  • Page 31

    Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...

  • Page 32: Warranty.

    Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...

  • Page 33

    Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...

  • Page 34

    Template auto pump 3.50 4.75 7/32 dia. Holes 4places.

  • Page 35

    Spare parts layout auto pump.

  • Page 36

    Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...

  • Page 37: Auto-Pump

    Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....

  • Page 38: Note

    Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...

  • Page 39: Caution

    Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.

  • Page 40

    Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...

  • Page 41: Warranty.

    Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...

  • Page 42

    Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...

  • Page 43

    Template auto pump 3.50 4.75 7/32 dia. Holes 4places.

  • Page 44

    Spare parts layout auto pump.

  • Page 45

    Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...

  • Page 46: Auto-Pump

    Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....

  • Page 47: Note

    Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...

  • Page 48: Caution

    Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.

  • Page 49

    Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...

  • Page 50: Warranty.

    Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...

  • Page 51

    Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...

  • Page 52

    Template auto pump 3.50 4.75 7/32 dia. Holes 4places.

  • Page 53

    Spare parts layout auto pump.

  • Page 54

    Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...

  • Page 55: Auto-Pump

    Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....

  • Page 56: Note

    Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...

  • Page 57: Caution

    Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.

  • Page 58

    Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...

  • Page 59: Warranty.

    Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...

  • Page 60

    Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...

  • Page 61

    Template auto pump 3.50 4.75 7/32 dia. Holes 4places.

  • Page 62

    Spare parts layout auto pump.

  • Page 63

    Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...

  • Page 64: Auto-Pump

    Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....

  • Page 65: Note

    Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...

  • Page 66: Caution

    Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.

  • Page 67

    Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...

  • Page 68: Warranty.

    Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...

  • Page 69

    Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...

  • Page 70

    Template auto pump 3.50 4.75 7/32 dia. Holes 4places.

  • Page 71

    Spare parts layout auto pump.

  • Page 72

    Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...

  • Page 73: Auto-Pump

    Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....

  • Page 74: Note

    Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...

  • Page 75: Caution

    Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.

  • Page 76

    Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...

  • Page 77: Warranty.

    Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...

  • Page 78

    Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...

  • Page 79

    Template auto pump 3.50 4.75 7/32 dia. Holes 4places.

  • Page 80

    Spare parts layout auto pump.

  • Page 81

    Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...

  • Page 82: Auto-Pump

    Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....

  • Page 83: Note

    Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...

  • Page 84: Caution

    Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.

  • Page 85

    Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...

  • Page 86: Warranty.

    Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...

  • Page 87

    Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...

  • Page 88

    Template auto pump 3.50 4.75 7/32 dia. Holes 4places.

  • Page 89

    Spare parts layout auto pump.

  • Page 90

    Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...