- DL manuals
- KUSSMAUL
- Air Compressor
- Auto-Pump 091-9B-220
- Instruction Manual
KUSSMAUL Auto-Pump 091-9B-220 Instruction Manual - Warranty.
VEHICLE WIRING INSTALLATION
1. The Auto Pump is supplied with a 220/240 volt A.C. line cord and is ready to operate. The
line cord may be plugged into an available outlet or the cord may be cut and permanently
wired to the 220/240 volt A.C. system in the vehicle.
2. The compressor is calibrated to cut-in at 70 PSI and cut-out at 90 PSI . For higher cut-in
and cut-out, turn the range nut clockwise . To lower cut-in turn range nut counterclockwise .
Do not exceed 100 PSI .
COMPRESSOR OUTPUT IS 100 PSI MAXIMUM. DO
NOT EXCEED 100 PSI OR YOU WILL VOID
WARRANTY.
NOTE
THIS PUMP REQUIRES A MINIMUM OF 220
VOLTS FOR OPERATION. AT LOWER VOLTAGES
THE PUMP WILL NOT START
220/240 VOLT
POWER CORD
Summary of Auto-Pump 091-9B-220
Page 1
Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....
Page 2: Note
Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...
Page 3: Caution
Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.
Page 4
Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...
Page 5: Warranty.
Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...
Page 6
Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...
Page 7
Template auto pump 3.50 4.75 7/32 dia. Holes 4places.
Page 8
Spare parts layout auto pump.
Page 9
Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...
Page 10: Auto-Pump
Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....
Page 11: Note
Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...
Page 12: Caution
Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.
Page 13
Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...
Page 14: Warranty.
Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...
Page 15
Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...
Page 16
Template auto pump 3.50 4.75 7/32 dia. Holes 4places.
Page 17
Spare parts layout auto pump.
Page 18
Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...
Page 19: Auto-Pump
Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....
Page 20: Note
Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...
Page 21: Caution
Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.
Page 22
Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...
Page 23: Warranty.
Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...
Page 24
Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...
Page 25
Template auto pump 3.50 4.75 7/32 dia. Holes 4places.
Page 26
Spare parts layout auto pump.
Page 27
Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...
Page 28: Auto-Pump
Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....
Page 29: Note
Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...
Page 30: Caution
Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.
Page 31
Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...
Page 32: Warranty.
Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...
Page 33
Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...
Page 34
Template auto pump 3.50 4.75 7/32 dia. Holes 4places.
Page 35
Spare parts layout auto pump.
Page 36
Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...
Page 37: Auto-Pump
Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....
Page 38: Note
Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...
Page 39: Caution
Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.
Page 40
Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...
Page 41: Warranty.
Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...
Page 42
Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...
Page 43
Template auto pump 3.50 4.75 7/32 dia. Holes 4places.
Page 44
Spare parts layout auto pump.
Page 45
Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...
Page 46: Auto-Pump
Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....
Page 47: Note
Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...
Page 48: Caution
Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.
Page 49
Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...
Page 50: Warranty.
Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...
Page 51
Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...
Page 52
Template auto pump 3.50 4.75 7/32 dia. Holes 4places.
Page 53
Spare parts layout auto pump.
Page 54
Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...
Page 55: Auto-Pump
Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....
Page 56: Note
Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...
Page 57: Caution
Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.
Page 58
Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...
Page 59: Warranty.
Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...
Page 60
Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...
Page 61
Template auto pump 3.50 4.75 7/32 dia. Holes 4places.
Page 62
Spare parts layout auto pump.
Page 63
Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...
Page 64: Auto-Pump
Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....
Page 65: Note
Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...
Page 66: Caution
Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.
Page 67
Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...
Page 68: Warranty.
Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...
Page 69
Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...
Page 70
Template auto pump 3.50 4.75 7/32 dia. Holes 4places.
Page 71
Spare parts layout auto pump.
Page 72
Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...
Page 73: Auto-Pump
Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....
Page 74: Note
Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...
Page 75: Caution
Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.
Page 76
Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...
Page 77: Warranty.
Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...
Page 78
Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...
Page 79
Template auto pump 3.50 4.75 7/32 dia. Holes 4places.
Page 80
Spare parts layout auto pump.
Page 81
Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...
Page 82: Auto-Pump
Instruction manual auto-pump 220/240 vac air compressor system tel: in ny 631-567-0314 toll free: 800-346-0857 fax: 631-567-5826 1 year warranty book# 091-9b-220 4-18-2002 ® kussmaul electronics co., inc . 170 cherry ave., west sayville, n.Y. 11796 model #091-9b-220 input :220/240 volt, 50/60 hz, 1....
Page 83: Note
Introduction the 091-9b-1 auto-pump air compressor system is a 220/240 volt 50/60 hz shaded pole a.C. Motor operating a single cylinder air compressor designed specifically for installation on vehicles with air brakes . During long idle periods of the vehicle when even the slightest seepage can caus...
Page 84: Caution
Caution no condensate or water must be allowed to enter or accumulate in the output of the auto pump. Route output pressure line downward from auto pump to permit moisture to drain away. Water in the pump outlet will induce failure ! Water damage will void warranty.
Page 85
Vehicle tubing installation 1. Mount all components in a suitable location, preferably in a high area above the air system . Do not mount in engine compartment or near any source of heat or dirt . The system may be connected to any point in the vehicle's air system . 2. Mount air compressor in a ver...
Page 86: Warranty.
Vehicle wiring installation 1. The auto pump is supplied with a 220/240 volt a.C. Line cord and is ready to operate. The line cord may be plugged into an available outlet or the cord may be cut and permanently wired to the 220/240 volt a.C. System in the vehicle. 2. The compressor is calibrated to c...
Page 87
Specification & outline auto pump input : 220/240 volts a.C. 50/60 hz, 1.9/2.2 amps weight: 13 lbs motor horsepower: 1/8 hp motor type: shaded pole a.C. Compressor output: 0.76 cfm open flow, 100 psi maximum. Pressure switch: adjustable set point-factory set to 70 psi cut-in, 90 psi cut-out switch d...
Page 88
Template auto pump 3.50 4.75 7/32 dia. Holes 4places.
Page 89
Spare parts layout auto pump.
Page 90
Auto pump rebuilding kit 091-9e is available . For simplified mounting mounting plate warranty all auto pumps of kussmaul electronics company inc. Are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any materi...