La Crosse Technology WS-8117U-IT Quick Setup Manual - page 2
5
x
MINUTES: The Minutes will flash. Use the PLUS button to set the Minutes. Press and
release the SET Button once.
x
YEAR: The Year will flash. Use the PLUS button to set the Year. Press and release the
SET button once.
x
MONTH: The Month will flash. Use the PLUS button to set the Month. Press and release
the SET button once.
x
DATE: The numeric day will flash. Use the PLUS button to set the correct Date.
x
WEEKDAY: The alphabetic Day will flash. Use the PLUS button to set to the correct Day.
x
12/24-HOUR TIME: Either 12 or 24 will flash on the display. Use PLUS button to change
from 12-hour to 24-hour time. Press and release the SET button once.
x
FAHRENHEIT OR CELSIUS: A degree symbol will flash, followed by F or C. Use the
PLUS button to select. Press and release the SET button once to confirm and exit.
SET TIME ALARM
Press and hold the ALM button for five seconds to enter the alarm set mode.
x
HOUR: The Alarm Time will begin to flash and “ALARM” and alarm icon (()) will display.
Press and release the PLUS button to adjust the Hour (watch for am or pm). Press and
release the ALARM button to advance to the minutes.
x
MINUTES: Press and release the PLUS button to adjust the Minutes. Press and release the
ALM button and you are done.
ACTIVATING/DEACTIVATING ALARM:
Press and release the ALARM button.
When the alarm time and Alarm Icon ((())) are showing to the right of the minutes, the alarm is
activated. Unit will return to actual time but continue showing the alarm icon ((())). To turn off the
alarm function, press and release the alarm button. The Icon will no longer be displayed when the
alarm is off.
SNOOZE SETTING
The snooze can only be activated during alarm time for a snooze duration of 10 minutes by
pressing the SNZ button on the back of the clock
6
DISPLAY OPTIONS
There are 4 possible display modes to view the day, seconds, and temperatures. The
month&date/weekday/indoor temperature/outdoor temperature is the default.
Change the display:
1.
Press the PLUS button. The display should now show the
month&date/weekday/seconds/outdoor temperature.
2.
Press the PLUS button a second time and the display will show the
month&date/weekday/indoor temperature/seconds.
3.
Press the PLUS button a third time and the display will show the
month&date/seconds/indoor temperature/outdoor temperature.
Press the PLUS button a fourth time and the display will return to the normal display.
LOW BATTERY ICON
The clock will tell you when the batteries are low in the outside transmitter or the atomic clock.
Low battery icon for atomic clock.
Low battery icon for TX37U-IT transmitter.
POSITIONING AND MOUNTING
POSITIONING THE ATOMIC CLOCK:
There are two possible ways to mount the atomic clock:
Foldout table stand or wall mount.
FOLDOUT TABLE STAND
The foldout table stand is located on the back of the clock.
Pull the stand out from the bottom center edge of the atomic clock, below the
battery compartment. Once the foldout table stand is extended, place the atomic
clock in an appropriate location.
7
WALL MOUNT
x Using a straightedge, horizontally space three screw positions on a wall.
x Install three mounting screws (not included) into a wall within transmission
range—leaving approximately 3/16 of an inch (5mm) extended from the wall.
x Place the atomic clock onto the screws, using the hanging holes on the backside.
x Gently pull the atomic clock down to lock the screws into place.
NOTE:
Always ensure that the atomic clock locks onto the screws before releasing.
POSITIONING THE OUTDOOR TEMPERATURE SENSOR
The remote temperature sensor should be mounted vertically to avoid damage.
MOUNTING WITH SCREWS
1.
Remove the mounting bracket from the remote temperature
sensor.
2.
Place the mounting bracket over the desired location (wall
or table mount).
3.
Through the two screw holes of the bracket, mark the
mounting surface with a pencil.
4.
Carefully screw mounting bracket onto the mounting
surface. Ensure that the screws are flush with the bracket.
5.
Insert the remote temperature sensor into the bracket. Best
if mounted vertically as pictured.
To achieve a true temperature reading, avoid mounting where direct sunlight can reach the
outdoor temperature sensor. It is recommended to mount the outdoor temperature sensor on a
North-facing wall or in any well shaded area. The maximum transmitting range is 330-feet (100
meters) obstacles such as walls, concrete, and large metal objects can reduce the range.
Place both units in their desired location, and wait approximately 10 minutes before permanently
mounting to ensure that there is proper reception. The outdoor temperature sensor is not
waterproof and should not be placed anywhere it will become submerged in water or subject to
standing water or snow.
8
MAINTENANCE
x
Keep the clock in a dry place.
x
Do not expose the instrument to extreme temperatures, vibration or shock.
x
Clean it with a soft damp cloth. Do not use solvents or scouring agents.
x
The product is not a toy. Keep it out of reach of children.
x
The product is not to be used for medical purpose or for public information, but is
determined for home use only.
x
The specifications of this product may change without prior notice.
x
Improper use or unauthorized opening of housing will void the warranty.
x
If the unit does not work properly, change the batteries.
SPECIFICATIONS:
Temperature measuring range
Indoor:
14.1ºF to 100ºF (-9.9ºC to 37.8ºC) ("OF.L" displayed if outside this range)
Outdoor:
-39.8ºF to 139.8ºF (-39.8ºC to 59.9ºC) ("OF.L“ displayed if outside this range)
Temperature checking interval
Indoor:
every 20 seconds
Outdoor:
every 4 seconds
Transmission distance: maximum 330 feet (100 meters) in open field
Power source (Alkaline batteries recommended)
Atomic clock:
2 x AA, 1.5V batteries (not included)
Sensor:
2 x AA, 1.5V batteries (not included)
Battery life:
about 24 months
Dimensions (L x W x H)
Atomic clock:
12.20“ x 1.18“ x 8.03“ (310 x 30 x 204mm)
Sensor:
5.05” x 1.50” x 0.83” (128.3 x 38.2 x 21.2 mm)
Time numbers:
2” tall (50.08mm)
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product against
manufacturing defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on products purchased
and used in North America and only to the original purchaser of this product. To receive warranty