Congratulations on the purchase of your of a new motorized treadmill. To help to ensure the enjoyable and trouble-free operation of your new treadmill, we strongly suggest you read this manual carefully and follow its recommendations. Table of contents lohas t2 lohas t3 important safety instruction ...
Front top view 20 00 m m 4 f ee t m in right side left side 1000mm 2 feet min 1000mm 2 feet min danger – to reduce the risk of electrical shock, always unplug this appliance from the electrical outlet immediately after using and before cleaning. ♦ use this appliance only for its intended use as desc...
1: frame 2: base frame 3: support post (left) 4: support post (right) 5: screws 6: nuts 7a: power plug 7b: power wire 8: handlebar (left) 9: handlebar (right) 10: console 11: bottle holder 12: safety key 13: support post housing (upper left) 14: support post housing (lower left) 15: screws 16: suppo...
Lohas t2 assembly instruction 1. Place book holder bracket (25) onto the rear of the console (2 holes on the bracket). Use 4 screws (26) to secure. 2. Slide book holder (24) down onto the brackets (25). Use 4 screws (27) to secure. (3 holes on the bracket) 1. Remove the screw (5) , and nut (6) from ...
Lohas t3 assembly instruction warning after unpacking the fitness equipment, examine it carefully for possible damage. If there is any damage or there are missing parts, please contact your retailer or an authorized repair facility for assistance. 1. Since your treadmill is a heavy piece of equipmen...
Lohas t3 assembly instruction 1. Place book holder bracket (25) onto the rear of the console (2 holes on the bracket). Use 4 screws (26) to secure. 2. Slide book holder (24) down onto the brackets (25). Use 4 screws (27) to secure. (3 holes on the bracket) 1. Remove the screw (5) , and nut (6) from ...
Lohas t2/t3 console operation start / stop : this will start the treadmill and this will stop the treadmill. There will also be an emergency stop switch. (safety key) incline up > : this will select program / level in setting mode before starting. This will increase the elevation by one increment at...
Lohas t2 / t3 lohas t2 / t3 audio in / out (option) lohas t2/t3 console operation 7.
Program operation and instruction lohas t2/t3 console operation under standby status, press the “mode” button, then press the speed “ > ” or “ > ” (incline “ > ” or “ > ” ) button to enter the program setting. Program in sequence as below : manual run “p1~p11”→”user1~user2”→”h.R.C”→”body mass”, when...
(1) use either speed “ > ” or “ > ” (incline “ > ” or “ > ”) buttons to select hrc program. (2) press the “mode” button. (3) use either speed “ > ” or “ > ” (incline “ > ” or “ > ”) buttons to select which time (12 – 99) 24 is the default. (4) press the “mode” button. (5) use either speed “ > ” or “...
4. Body mass mode : (1) use either speed “ > ” or “ > ” (incline “ > ” or “ > ”) buttons to select body mass program. (2) press the “mode” button. (3) use either speed “ > ” or “ > ” (incline “ > ” or “ > ”) buttons to select sex (m – f). (4) press the “mode” button. (5) use either speed “ > ” or “ ...
Under preset programs, the preset workout time is 24 minutes. You can adjust the workout time while in set program mode. Lohas t2/t3 preset program km/h speed program incline program 11.
Under preset programs, the preset workout time is 24 minutes. You can adjust the workout time while in set program mode. Lohas t2/t3 preset program speed program incline program mph 1.2 1.8 2.4 1.2 1.8 2.4 1.2 1.8 2.4 0.6 1.2 1.8 0.6 1.2 1.8 1.2 1.8 2.4 1.8 2.4 3.0 2.4 3.0 3.6 1.8 2.4 2.8 4.3 4.9 5....
Utilization ♦ always stretch your muscles before commencing the exercise program. Warm up slowly by walking at a slow speed. Increase workout intensity gradually until you reach your desired workout pace. Decrease workout intensity gradually to an easy walk. Allow your heart rate to decrease to a no...
Maintenance general cleaning 1. Before proceeding, ensure that the treadmill power is off and that it is unplugged from the electrical outlet. 2. Remove dust, use a small vacuum nozzle to carefully vacuum around all visual components. 3. To remove film or dirt use a slightly damp rag with a mild cle...
Maintenance belt lubrication use only 100% silicone and avoid using aerosol silicone sprays which include additives and petroleum distillates. One ounce of silicone should be used for each application. Your treadmill running belt should be lubricated every 3 months (irregardless of use) or every 50 ...
Maintenance 1.Check the speed sensor if it is damaged or well fixed; the speed sensor has to be fixed where it close to the magnet within 2-3mm. 2.Check the signal cable of speed sensor if it is well connected to the controller. To solve the problem, please reconnect the signal cable to the controll...
