Lab.gruppen fP Series FP 3400 Specifications - Specifications
SPECIFICATIONS
Lab.gruppen AB, Gullregnsvägen 16, SE-434 44 Kungsbacka, Sweden.
Tel +46 300 56 28 00 Fax +46 300 56 28 99 e-mail: info@labgruppen.com www.labgruppen.com
Max output power
1)
EIA
EIA
EIA
EIA
FTC
EIA at 1 kHz and 1% THD
20–20 kHz at 0.1% THD
MLS-switch
–5 dB
–4 dB
–2 dB
0 dB Full
0 dB Full
16
Ω
per channel
160 W
200 W
340 W
520 W
500 W
8
Ω
per channel
300 W
400 W
700 W
1100 W
1000 W
4
Ω
per channel
600 W
750 W
1300 W
1500, 1900
3)
W
1450 W
2
Ω
per channel
1200 W
1400 W
1550, 1900
3)
W
1700
2)
, 3000
3)
W
1650 W
16
Ω
bridged
600 W
800 W
1400 W
2200 W
2000 W
8
Ω
bridged
1200 W
1500 W
2600 W
3000, 3800
3)
W
2900 W
4
Ω
bridged
2400 W
2800 W
3100, 3800
3)
W
3400
2)
, 6000
3)
W
3300 W
Max output voltage
8 ohms load, MLS @ 0 dB
52 Vrms
58 Vrms
75 Vrms
94 Vrms
Peak voltage, no load
79 V
82 V
107 V
132 V
fP 3400
Distortion etc.
THD 20 Hz-20 kHz and 1 W to full power
0.08 %
THD @ 1 kHZ and –1 dB under clip
0.03 %
DIM 30 at –3 dB under clip
0.06 %
Hum and Noise
<–110 dB
Channel separation @10 kHz
70 dB
Output impedance
60 m
Ω
Slew Rate
20 V/
s
Inputs
Gain, selectable [dB]
20, 23, 26, 29, 32, 35, 38, 41
Impedance 20
kohm
Common mode rejection
50 dB
Front Panel
Gain controls
(2) channel A, B
31 pos detent
Clip Indicator
(2) red LEDs
Output headroom
indicators
(10) green LEDs
Fast peak – slow release
Temp Indicator
(2) yellow LEDs
80°C at heatsink
VHF indicator
(2) yellow LEDs
>12 kHz at full power
On Indicator
(2) green LEDs
DC rail voltage for
channel A and B
AC Indicator
(1) green LED
AC power present
AFS Indicator
(1) green LED
Fuse saver activated
Rear Panel
Input connectors
(2) Neutrik Combo XLR type, 3 pin
and 1/4˝ jack
Link connector
(2) XLR type, 3 pin male
Output connectors (2) Neutrik 4-pole Speakon® connectors
Switches:
Clip limiter A and B
On–Off (switchable)
MLS switch
0, –2, –4, –5 dB
Link-switch
Ch. A–B
Power
230 V version
115 V version
Operation voltage
130 V–265 V AC 65 V–135 V AC
Minimum start voltage
175 V
85 V AC
Full output power
at 4 ohms
180 V–265 V AC 90 V–130 V AC
Peak inrush current
(Soft start limited)
5 A
5 A
Current Draw @ 4ohms
Quiescent power (no load) 1 Arms
2 Arms
1/8 of full power (–9 dB)
5 Arms
10 Arms
1/3 of full power (–5 dB)
11 Arms
22 Arms
At full power (0 dB)
@1 kHz 1% THD
26 Arms
52 Arms
Net Dimensions
mm
483 (19˝) W ✕ 88 H ✕ 347 D
inch
19˝ W ✕ 3.5˝ H ✕ 13.7˝D
Shipping Dimensions
mm
560 W ✕ 180 H ✕ 500 D
inch
22˝ W ✕ 7.1˝ H ✕ 19.7˝D
Weight
Net
10 kg (22 lbs)
Shipping
11.6 kg (25.6 lbs)
Approvals
CE:
Emission
EN 55 103-1, E3
Immunity EN 55 103-2, E3, with S/N below 1% at normal operation level4)
Safety
EN 60065, class I
ETL listed: Conforms to ANSI/UL STD 6500 and Certified to CAN/CSA E60065-00
FCC:
Complies with Class B digital device, Part 15 of the FCC Rules.
NOTES:
1) Specifications measured with 230 V AC
2) Component tolerance dependent
3) Continuous power, one channel driven or peak power both channels driven
(Thermal protection may occur at high continuous power)
4) Normal operation level 1/8 of full power or –9 dB below clip level.
Lab.gruppen reserve the right to alter functions or the specification without prior
notice.