1. DL manuals
  2. Laguna
  3. Lathe
  4. Revo 2036
  5. Instruction Manual

Laguna Revo 2036 Instruction Manual

Summary of Revo 2036

  • Page 3

    4 safety rules as with all machinery there are certain hazards involved with the operation and use. Using it with caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. If you h...

  • Page 4

    Limited warranty new machines and accessories sold by laguna tools carry a one-year warranty effective from the date of shipping. Machines sold through dealers must be registered with laguna tools within 30 days of purchase to be covered by this warranty. Laguna tools guarantees all new machines and...

  • Page 5

    Introduction to the lathe turbo lathes are designed and built to satisfy the most imaginative fantasies of woodworkers. With outstanding new features, energetic performances and so many user- friendly considerations, turbo lathes simply turn turning jobs an unprecedented experience. Featuring  high...

  • Page 6

    Identifications.

  • Page 7

    Specifications models t-50 t-60 operation information swing over bed 20” 24” dist. Between centers 36” 48” swing over tool rest base 16” 20” spindle speeds: h 200-3500rpm (variable) 200-3500rpm (variable) l 50-820rpm （variable） 50-820rpm (variable) floor to spindle center height 44” 44” headstock tr...

  • Page 8

    Power supply warning: for your own safty and protection of property, consult an electrician if you are unsure about wiring practices or electrical codes in your area. Caution: if the plug does not fit the available receptacle, or the machine must be reconnected for use on a different type of circuit...

  • Page 9

    Assembling instruction warning: the lathe must be disconnected from power source during assembly. Legs installation (fig. 2) 1, life the lathe off the pallet by using a hoist or forklift. Place it on a table or workbench with sufficient clearance to allow the support legs to be attached from underne...

  • Page 10

    Comparator brackets (optional) see fig.4, mount the front comparator bracket c to the back of the headstock with two 12mm socket head cap screws. This bracket can be also used for spindle shield guard mounts. Rear comparator bracket should be mounted to the back of the tailstock. The bracket has a s...

  • Page 11

    A: right end of be d: for up to 56” center distanc (fig. 6). B: right leg: for outboard turning (fig.7) c:front bed: for convenience operation (fig.8) 12” swing away extension bed (standard for t-60, optional for t-50) 12” swing away bed is standard for t60 lathe (pre-installed before delivery). If ...

  • Page 12: Operation Of Lathe

    1, with an assistant, attach the extension bed to lathe bed right end with two head cap bolts b. Slightly tighten the bolts. These two bolts must be taken off as soon as swing away system assembly is completed (fig.9) 2, adjust the extension bed flush to the lathe bed. Make sure inside ways and surf...

  • Page 13

    Change over of low-high speed ranges this lathe is designed with two speed ranges (low/high speed range) , within each range, speed can be changed variablly by an electronic variable speed controller. To change the spindle speed range, please follow instructions as below (fig 14): fig.14 1, unplug t...

  • Page 14

    Tool rest base (banjo) the banjo is designed with cam-lock system. It can slide along the bed freely when unlocked. Loosen the locking handle and move the banjo to the desired place. Lock the lever firmly after adjustment. Tool rest a 14” tool support is provided with your lathe as standard. It is d...

  • Page 15: Maintenance

    4, insert lock rod a (fig.16) into handwheel hole. Hold the rod and tighten the faceplate with faceplate wrench. 5 ， there is a set screw on face plate. Please tighten it when you work with the lathe in reverse rotation. Fig. 16 tailstock quill the tailstock quill can be turned in and out by turning...

  • Page 16: Parts List / Diagrams

    Parts list / diagrams parts list for models t-50 and t-60 note: the parts for t-50 and t-60 lathes are mostly the same, except for some parts are different which are underlined below and clearly specified for t-50 or t-60. Index no. Part no. Description size qty 1 hwt50-01-10 headstock casting for t...

  • Page 17

    25 hwt50-01-27 position pin 1 26 gb/t 889.1-2000 lock nut m12 1 27 hwt50-01-14 degree indictor 28 hwt50-01-16 spindle hand-wheel 1 29 hwt50-01-35 cover for t-50 t-50 1 29a hwt60-01-35 cover for t-60 t-60 1 30 hinge 1 31 gb/t70.3-2000 hex socket cap screw m5×14/16 4 32 gb/t 97.1-1985 flat washer 5 8 ...

  • Page 18

    55 ce4t-10r-01 emergency stop button 1 56 mpd2-11b on/off switch 1 mcbh-00 bracket 1 mcb-10 contact point 1 mcb-01 contact point 1 57 c3ss1-10b-20 three-position switch 1 58 speed controller 1 59 hwt50-04-15 speed adjusting button 1 60 gb/t 77-2000 hex socket cap screw m4×6 1 61 cable clamp 10.4mm 1...

  • Page 19

    82 gb/t 889.1-2000 hex nut m8 1 83 hwt50-02-01 tail stock for t-50 t-50 1 83a hwt60-02-01 tail stock for t-60 t-60 1 84 hwt50-02-11 position block 1 85 hwt50-02-10 lock handle 1 86 hwt50-02-02 sleeve 1 87 hwt50-02-03 lead screw 1 88 hwt50-02-04 position ring 1 89 hwt50-02-05 washer 1 90 hwt50-02-06 ...

  • Page 20

    114 hwt50-01-52 wrench 1 115 hwt50-01-40 dead center 1 116 hwt50-01-41 live center 1 117 hwt50-01-42 knockout bar 1 118 hwt50-01-43 profiling center 1 119 hwt50-01-44 profiling center 1 120 hwt50-01-45 knockout rod 1 121 hwt50-01-55 spindle locating rod 122 hwt50-03-02 tool rest 1 123 leveler m16×65...

  • Page 21

    150 gb/t 6170-2000 hex nut m12 4 151 hwt50-05-05 swing extension bed 12” 1 152 gb/t70.1-2000 hex socket cap screw m12×40 2 153 hwt50-05-06 hinge 2 154 gb/t 70.1-2000 hex socket cap screw m8×25 6 155 gb/t 93-1987 spring washer 8 6 156 gb/t 77-2000 set screw m6×10 4 157 hwt50-05-07 hinge shaft 1 158 h...

  • Page 22: Parts Diagrams

    Parts diagrams.

  • Page 24

    Laguna tools is not responsible for errors or omissions. Specifications subject to change. Machines may be shown with optional accessories. © 2017, laguna tools, inc. Laguna® and the laguna logo® are the registered trademarks of laguna tools, inc. All rights reserved. 2072 alton parkway. Irvine, ca 9...