S s s u u u p p p e e e r r r t t t r r r a a a c c c e e e r r r 2 2 2 5 5 5 0 0 0 0 0 0 h h h t t t i i i 2 2 2 5 5 5 0 0 0 0 0 0 w w w i i i n n n t t t e e e l l l l l l i i i g g g e e e n n n t t t d d d i i i s s s c c c h h h a a a r r r g g g e e e f f f o o o l l l l l l o o o w w w s s s ...
1 before connecting and using the projector, it is important to read carefully all the instructions in this manual. Qualified personnel only, in compliance with all the security laws, can do the installation, the maintenance and the utilisation of this projector. Before connecting the projector, mak...
2 general description supertracer is an intelligent followspot ideal for distance between 20 and 80mt, it has an external ballast, zoom between 7.4° and 15.6° and it is perfectly balanced. Supertracer has a colour wheel, filter correction, frost filter, focusing, dimmer and strobe, this effects is c...
3 rear panel as shown in the figure, the following elements ca be seen on the rear panel: 1. Rear handle 2. Serial number plate 3. Dmx address area 4. Control assignment section 5. Xlr dmx 512 in/out 6. Line and electronic fuse 7. Main power supply cable 8. On/off lamp switch 9. Rs232 for tracer con...
4 noise level after the projector has been powered up and the initial configuration takes place, the noise produced by the projector is primarily due to its cooling system. The noise level is much lower than the limit of 70 db a permitted by law. Packing the projector is shipped and delivered in a c...
5 start – up procedures positioning and installation follow these steps for opening the package and installing the projector in its working position: • place the projector near the place it will be installed. • open the package and remove the anchoring elements, accessories, and user manual. • caref...
6 lamp installation • switch off projector • loosen the cheese-headed screw hexagon built in front and on the back of the projector of the top lid and remove the lid. • remove the lamp from the packing and carefully read the manufacturer’s instructions. • insert the lamp into the socket • block the ...
7 dmx channel assignment channel function 01 colour 02 colour correction 03 iris 04 dimmer & shutter 05 focusing 06 special function dmx channel functions are described in the table. When you address a projector keep in mind that the base channel (or starting channel) corresponds to the first channe...
8 channel 1 = colours percent values decimal values 0 > 5.9 % white 0 > 15 6.3 > 9.4 % white / red 16 > 24 9.8 > 13.3 % red 25 > 34 13.7 > 18 % red / yellow 35 > 46 18.4 > 21.6 % yellow 47 > 55 22 > 25.5 % yellow / magenta 56 > 65 25.9 > 29.8 % magenta 66 > 76 30.2 > 33.7 % magenta / green 77 > 86 3...
9 control systems tracer control unit supertracer comes with a control unit mounted on the adjustable bar and connected to the projector by means of a proper cable through 9 pin din connector. The tracer control unit is powered at low voltage 12 volts directly by the projector and it is able to cont...
10 dimmer /shutter section this section contains the controls for light beam characteristics: intensity, my means of the dimmer, and strobe effect, using the variable speed shutter. Note that the action of the slider for this section depends on the position of the dimmer/strobe selector. When the di...
11 cascade control from the tracer console when several projectors are connected by cable, the console on the first projector can control all functions on the following projectors. For this reason, the projectors must be connected with a standard dmx cable, in/out 3 or 5 pin connectors. Each project...
12 optical system the supertracer followspot 2500 is provided with a high-efficiency optical system made of mirror, optic condenser and two anti-flare lenses. This system lets supertracer followspot 2500 project an extremely powerful and homogenous light beam. The supertracer use osram hti 2500w/se ...
13 maintenance safety guards, lenses and filters must be replaced if they are visibly damaged to the point that they become ineffective (i.E.: if they have deep slashes or cuts).. The lamp must be replaced if damaged, cracked or deformed by the heat planned maintenance operration frequency responsib...
14 m3 surface temperature test before you check the temperature, make sure the projector is in the full operating mode (wait about 20 minutes after switching on the projector). Use a contact probe to measure the surface temperature on the projector’s metal case and determine the hottest area at the ...
15 troubleshooting *before switching on the projector, identify and remove the causes that made the safety fuse intervene. Call your area dealer or feel free to contact the manufacturer for any additional assistance. Problem possible cause solution no mains power supply make sure the mains power is ...
16 spare parts when ordering spare parts for the projector remember to mention the model and serial number which can be found on the plate at the rear of the projector. Call your area dealer or feel free to contact the manufacturer for any additional assistance. Spare part list lenses order from rea...
