Lamson & Sessions HW2155D Instruction Manual - page 2
LIMITED WARRANTY
The product you have purchased is guaranteed against defects
in workmanship and materials for the period stated on the
package. Warranties implied by law are subject to the same
time period limitation. Some states do not allow limitations on
how long an implied warranty lasts, so this time limitation may
not apply to you.
If the product fails due to a manufacturing defect during normal
use, return the product and dated sales receipt to the store
where purchased for replacement OR send the product and the
dated sales receipt to:
Lamson & Sessions
25701 Science Park Drive
Cleveland, OH 44122 USA
Attn: LHP Customer Service
Not Covered - Batteries, light bulbs, and other expendable items
are not covered by this warranty. Repair service, adjustment and
calibration due to misuse, abuse or negligence are not covered
by this warranty. Unauthorized service or modification of the
product or of any furnished components will void this warranty
in its entirety. This warranty does not include reimbursement for
inconvenience, installation, set-up time, loss of use, postage,
unauthorized service, or other products used in conjunction with,
but are not supplied by, Lamson & Sessions.
All requests for replacement must include a
dated sales receipt
(copies accepted). LAMSON & SESSIONS IS NOT LIABLE FOR
LOST PROFITS, INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL OR
CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION
ANY SUCH DAMAGES DUE TO IMPROPER WIRING OR MISUSE
OF THE PRODUCT. As some states do not allow the exclusion
or limitation of incidental or consequential damages, the above
limitation and exclusion may not apply to you.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
This device complies with RSS-210 of Industry Canada.
ALSO AVAILABLE FROM CARLON:
• Extend-A-Chime® – lets you hear your existing wired doorbell
in remote areas of your home or yard
• Plug-in and Battery Doorbells and Chimes
• On/Off Remote Switches
• Touch and Automatic Lighting Controls
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state. If
you have questions or need further assistance, please call
Lamson & Sessions at: 1-800-346-2646 Mon. - Fri., 9 a.m.
- 4 p.m. EST.
CHANGING DIGITAL CODE CHANNELS (optional)
This product utilizes digital channels to send a signal from
Transmitter to Receiver. The user can change the signal if out-
side interference occurs. If you use other wireless products in
your home, there is a slight possibility of interference. Use the
following instructions to change the current channel setting to
a new setting.
IMPORTANT! If you change the channel combination on the
Transmitter, you must change the combination on the Receiver.
If the channel combinations do not match, the system will
Front of
Receiver
Back of
Transmitter
not function!
1. Turn off power to the Receiver by removing the fuse
or switching the circuit breaker to “Off.”
2. Slide the Control Switch on Receiver Switch to the “Off”
position. Locate Channel Jumpers on back of the Transmitter
Switch and on front of the Receiver.
3. Channel codes are A, B, C & D.
4. Select proper channel by moving jumpers with tweezers.
5. Slide the Control Switch on the Receiver Switch to the
”ON” position.
6. Reinstall Receiver and Transmitter Switch by following
Installation Instructions.
SPECIFICATIONS
Detection Range: Up to 50'
Maximum Load: 350W, incandescent only
Rated Voltage:
120V AC, 60 Hz
Battery:
12-volt Type A23 alkaline
For indoor use only. Do not use with existing
three-way circuits.
CODE OPTIONS
0409 IS186
Made in China
©2004
25701 Science Park Drive
Cleveland, Ohio 44122
www.lamson-sessions.com
CODE OPTIONS
CHANNEL
JUMPERS
(Under plug)
Control
Switch
2. Coloque el Interruptor de Control del Interruptor Receptor en
la posición “Off” (apagado). Ubique los Conexiones del Canal
en la parte posterior del interruptor transmisor y en la parte
frontal del receptor.
3. Los códigos de canal son A, B, C y D.
4. Seleccione el canal correcto desplazando las conexiones
móviles con pinzas.
5. Coloque el Interruptor de Control del Interruptor Receptor en
la posición “ON” (encendido).
6. Vuelva a instalar el interruptor del receptor y del transmisor
siguiendo las instrucciones de instalación.
ESPECIFICACIONES
Alcance de detección: Hasta 50 pies
Carga máxima:
350 W, incandescente solamente
Tensión nominal:
120 VCA, 60 Hz
Batería:
Alcalina de 12V tipo A23
Para uso interior solamente. No apto para usar con los cir-
cuitos existentes de tres direcciones.
GARANTÍA LIMITADA
Este producto que ha comprado está garantizado por el periodo
que se informa en el envase contra defectos de mano de obra y
materiales. Las garantías implícitas legales se limitan al mismo
periodo de tiempo. Algunos estados no permiten limitaciones
en el periodo de extensión de las garantías, por lo tanto, estas
limitaciones pueden no aplicarse a su caso.
Si el producto tiene una falla provocada por defectos de fabri-
cación durante su uso normal, devuelva el producto y el recibo
de compra fechado a la tienda en donde lo compró para que
se lo sustituyan o envíe el producto y el recibo de compra
fechado a:
Lamson & Sessions
Atencíon: Servicio de cliente de LHP
25701 Science Park Drive
Cleveland, Ohio 44122 EE.UU.
Las siguientes piezas no están cubiertas por la garantía: pilas,
bombillas o focos y cualquier otra pieza fungible. Esta garantía
tampoco incluye el servicio de reparación, ajuste o calibración
debido al uso indebido o negligente. El servicio de reparación
o modificación no autorizado del producto o de cualquiera de
las piezas que se suministran invalidará la garantía en su to-
talidad. Esta garantía no incluye reembolso por inconveniencia,
instalación, tiempo de preparación para la puesta en marcha,
pérdida de tiempo de uso, franqueo, servicio de reparación no
autorizado u otro producto utilizado conjuntamente con éste
pero que no lo suministra Lamson & Sessions.
Todas las solicitudes de sustitución deben incluir
el recibo de
compra fechado (se aceptan copias). LAMSON & SESSIONS
NO ASUME RESPONSABILIDAD POR GANANCIAS PERDIDAS,
DAÑOS INDIRECTOS, ESPECIALES, EJEMPLARES, INCIDENTALES
O PERJUICIOS DEBIDO AL USO INDEBIDO DEL PRODUCTO O LA
PREPARACIÓN INCORRECTA DE LOS CABLES. Como algunos
Estados no permiten la exclusión o limitación de los daños y
perjuicios, las limitaciones y exclusión anteriores pueden no
aplicarse a su caso.
Este dispositivo cumple las reglas de la Comisión Federal de
Comunicaciones (FCC), parte 15. La operación está sujeta a las
dos condiciones siguientes:
1. Este dispositivo no puede causar interferencia nociva; y
2. Este dispositivo debe aceptar cualquier interferencia que
puede recibir, incluyendo interferencia que pueda causar
operación indeseable.
Este dispositivo cumple con la norma industrial RSS-210 del
Canadá.
CARLON OFRECE TAMBIÉN:
• Extend-A-Chime® – para oír la campanilla conectada ex-
istante en un área distante de la casa o del patio.
• Campanillas y carillones enchufables y a baterias
• Interruptores remotos de encendido/apagado
• Controles de iluminacion automatico y por tacto
Esta garantía le proporciona derechos legales específicos y
además puede contar con otros derechos que varían según
el estado. Si desea formular preguntas o necesita asistencia,
sírvase llamar a: Lamson & Sessions al: 1-800-346-2646 de
lunes a viernes, de 09:00. a 16:00 hs (hora del Este).
CAMBIO DE LOS CODIGOS DE CANALES (opcional)
Este producto utiliza codigos digitales para enviar una señal
desde el transmisor al receptor. El usuario puede cambiar la
señal si ocurre interferencia exterior. Si usted usa otros productos
inalámbricos en su casa, existe una pequeña posibilidad de
interferencia. Utilice las instrucciones siguientes para cambiar
el ajuste actual del canal a un ajuste nuevo.
¡IMPORTANTE! Si usted cambia el codigo de canal en el
transmisor, usted puede cambiar el codigo en el receptor. Si el
codigo de canales no coinciden, el sistema no funcionará.
1. Desconecte la alimentación eléctrica al receptor sacando
el fusible o poniendo el disyuntor en la posición “Off.”
Parte frontal
del receptor
Parte
posterior del
transmisor
OPCIONES DEL
CÓDIGO
CONEXIONES DEL
CANAL (Debajo del
enchufe)
Interruptor de
Control
0409 IS186
Hecho en China
©2004
25701 Science Park Drive
Cleveland, Ohio 44122
www.lamson-sessions.com