B rew e xpress ® installat ion guide model # be-104r & be-104c by for more information see our instructional video online at www.Brewexpress.Com. Note - be-104r shown in illustrations. Impo rtant no te: do not r eturn this p roduc t to p lace o f purchas e withou t author izatio n. For re turn au th...
Cont en ts 1. Safety 1 - 2 2. Getting started 3 3. Hardware/tools 4 4. Specification and requirements 5 5. Location (area of installation) 6 6. Water installation 7 7. Power installation 8 8. Brewer installation 9 - 13 9. Testing 13 10. Troubleshooting 14 - 16.
1 safety important safeguards when using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. The voltage and frequency of the supply connections should conform to those of...
Important: read and follow instructions carefully before installing your brew express in-the-wall coffee system. For best results, it is advised that you hire a qualified professional. Always turn off all power at main electrical panel before attempting to install brew express. Improper electrical w...
3 get ting started important: read and follow instructions carefully before installing your brew express in-the-wall coffee system. For best results, it is advised that you hire a qualified professional. Getting started 1. Carefully unpack brew express from gift box. 2. Remove carafe and brew basket...
4 hardware/tools hardware brew express comes supplied with the following items to ensure a successful installation. Check to be certain all items have been included with your brewer. • (1) brewer (with short water line attached to connect with incoming water line) • (1) rough-in-box • (1) carafe and...
9 7/8" 249.8mm 11 3/4" 299.6mm 3 1/4" 82.6 mm 1" 24.3mm 9 7/8" 251.7mm 5 1/8" 130.8mm 8 3/8" 213.5 mm 3 7/8" 99.0 mm 3/4" 18.3 mm 8 1/2" 216.70 mm 10 1/8" 254.90 mm area on wall to be cut (use template) important: read and follow instructions carefully before installing your brew express in-the-wall...
6 location (area of installation) the brew express can be installed in most places where power and water are supplied. If only power is available, you may consider using a water bottle and pump. The most common locations are the kitchen, master bathroom or office. Installation inside an exterior wal...
Always turn off water supply at source. It is strongly advised you consult a qualified professional plumber when attempting to install the brew express in-the-wall coffee system. It is important to make sure there are no conflicts or obstructions in the wall cavity such as plumbing or electrical wir...
Always turn off power supply at main electrical panel before attempting any electrical installation. Local electrical codes vary. All electrical installation must be done in accordance with local codes. Installation must be performed by a qualified electrician, or equivalent. Important: installation...
9 brewer installation important: if installing unit prior to cabinets, it is strongly advised to consult with cabinet maker and build- ing contractor for exact height of counter top due to the various thicknesses of counter tops (tile laminate, granite, etc). For best results cut hole and install un...
Installation of rough-in-box 1. Locate wall studs adjacent to the desired location. Place template on wall as shown. Outside edge of slots in template should be even with left or right side of stud edge. The slots in the template designate the area to be cut. Outside edge of template is equivalent t...
5. Bring 1/4” water supply line to cut opening. Bring water line through grommet in rough-in-box (see supply detail). Slide rough-in-box into opening while pulling about 18” of water line through grommet hole. Secure rough-in-box to wall stud with sheet rock screws. Purge water line by running water...
12 brewer installation 6. After sheet rock screws are in place, bend tabs to finish securing rough-in box to wall. See figures 6 and 7. Use pliers (if needed) to bend/crimp tabs firmly to wall. Gently slide excess water line back through grommet into wall cavity leaving top of connector a maximum of...
13 brewer installation & testing testing once brew express has been installed into the rough-in-box it must be tested to ensure proper operation. 1. Turn on electrical power and power switch (located on top of brewer). The brew button icon should be illuminated. If the button icon is not illuminated...
14 troubleshooting button icon is not illuminated • ensure the power to the rough-in box is turned on (check circuit breaker). • ensure brewer is fully pressed into the rough-in box. • ensure the outlet inside the rough-in box is properly wired. Remove the brewer and check outlet with volt meter. If...
15 troubleshooting water overflow from brew basket • paper filter is not high enough and grounds are flowing over and plugging brew basket (use higher filter). • coffee grounds are too fine, use courser grind of coffee. Excessive steam • inlet water line connected to hot water supply (connect to col...
16 troubleshooting troubleshooting carafe or mug not detected (flashing brew light) • ird windows are dirty (wipe with moist towel and dry). • mug not close enough to ird (move further into brewer). Water dripping from spray head • spray head plugged (replace or clean spray head). • normally, some w...
® ® printed in china. Be104-ig/052808 © lance larkin 2008 www.Brewexpress.Com for customer service or technical service please call (866)-268-5953.
