- DL manuals
- Laney
- Musical Instrument Amplifier
- R5
- User Manual
Laney R5 User Manual
Summary of R5
Page 1
Laney r1 r2 r3/r3h r4/r4h r5 user manual richter bass amplification.
Page 2
Important safety instructions warning: when using electric products, basic cautions should always be followed, including the following. 1. Read all safety and operating instructions before using this product 2. All safety and operating instructions should be retained for future reference 3. Obey all...
Page 3
Laney care of your laney amplifier will prolong it's life.....And yours!. After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to ch...
Page 4
Laney 2 r1 front normal and high inputs are provided for connection of bass guitars. High output basses, either active or passive should be connected via the high socket. Low output basses should be connected using the normal input. High output basses may also be placed in the normal input if pre-am...
Page 5
Laney 3 laney selects the mid-frequencies to be cut or boosted in conjunction with the paramid gain control (7). To access lo mid-frequencies turn the frequency control anticlockwise, to access hi mid frequencies turn the frequency control clockwise. Sets the level of boost or cut applied to the fre...
Page 6
Laney 4 this control is used to set the level of gain present in the pre-amp. The higher the level of gain, the more the signal will clip producing distortion. The gain control should be used in conjunction with the volume control (10) to produce the desired signal characteristics. Engages and disen...
Page 7
Laney 5 laney this socket should be used to connect an extension-cabinet. The impedance of the extension-cabinet must not be less than 8 ohms. Connecting cabinets that have a lower impedance than 8 ohms will result in the amplifier overheating . Continual use in this manner may cause permanent damag...
Page 8
Laney 6 laney the enhance control provides an increased definition at the low-end of the frequency spectrum giving you a tighter, punchier sound. The enhance control does this by providing a dip in the frequency-response of the amplifier at approximately 200hz. This dip eliminates some of the second...
Page 9
T6.3a l 115v t3.15a l 230v ~ t6.3a l 115v t3.15a l 230v ~ f r & s v . Use ating upply oltage tunerout fxreturn fxsend l oudspeakers c - aution r . Efer to users manual for recommended speaker connections a 4 . Total load of no less than ohms may be connected at any time m p c 450 w ~50/60 h aximum o...
Page 10
Laney 8 laney normal and high inputs are provided for connection of bass guitars. High output basses, either active or passive should be connected via the high socket. Low output basses should be connected using the normal input. High output basses may also be placed in the normal input if pre-amp o...
Page 11
Laney 9 laney l imiter h orn v olume d.I. 1 b a ass mplifier r5 p ower 0 7 7 2 2 2 2 7 1 1 4 4 4 4 1 9 9 4 4 4 4 9 3 3 2 2 2 2 3 10 10 5 1k 4k 5 5 5 10 4 4 1 1 1 1 4 6 6 1 1 1 1 6 0 0 5 100 400 5 5 5 0 5 5 0 350 1k5 0 0 0 5 8 8 3 3 3 3 8 2 2 3 3 3 3 2 - - - - + + + + c omp i nputs h igh n ormal e nh...
Page 12
Selects the lo mid-frequencies to be cut or boosted in conjunction with the lo paramid level control (7). To access low lo mid-frequencies turn the frequency control anticlockwise, to access higher lo mid frequencies turn the frequency control clockwise sets the level of boost or cut applied to the ...
Page 13
Laney 11 laney richter r1 r2 r3 r3h r4 r4h r5 power output maximum power consumption 50/60hz input impedance normal/hi input sensitivity norma/hi fx loop level (nominal) minimum ext.Speaker impedance recommended minimum extension speaker power rating recommended richter extension cabinets 65w 120w 1...
Page 16
Laney amplification newlyn road, cradley heath, west midlands b64 6be united kingdom. Www.Laney.Co.Uk in the interest of on going product development laney reserves the right to amend specifications without prior notification.