Active products - switches www.Lanpro.Com lpsgw2400_ug_enb01w lp-sgw2400 24 ports 10/100/1000 24 ports remote web manageable smart switch 10/100/1000 mbps snmp capable lp-sgw2400 24 ports 10/100/1000 24 ports remote web manageable smart switch 10/100/1000 mbps snmp capable..
Www.Lanpro.Com active products - switches - lp-sgw2400 chapter 1 product specification thank you for the loyalty you have shown to our company and products. We are sure the performance and the quality of our devices will be up to your demanding standards. Lanpro provides technical support to your pro...
Www.Lanpro.Com active products - switches - lp-sgw2400 chapter 2 hardware installation b 2.1 quick installation guide choose a proper place for the lp-sgw2400 rack mountable switch, considering the surroundings such as power requirements, space, keep it away from sunlight, heat source, and electroma...
Www.Lanpro.Com active products - switches - lp-sgw2400 input the password (default there is no password), then click the “apply” and the configuration window will show as below: 5 open the browser, input the http://192.168.2.1 and “enter” it, you will see the switch login window as below (take 24 por...
Www.Lanpro.Com active products - switches - lp-sgw2400 3.3 ports port display link station and can set each port as: speed, flow control. Every port can choose one work mode in 7 kinds as below: 10m half-duplex, 10m full-duplex, 100m half-duplex, 100m full-duplex, 1000m full-duplex, auto- negotiation...
Www.Lanpro.Com active products - switches - lp-sgw2400 3.6 lacp lacp (ieee 802.3ad link aggregation protocol) provides a way to set up aggregation automatically between switches. Figure 7 3.7 rstp rstp is a protocol that prevents loops in the network and dynamically reconfigures which physical links ...
Www.Lanpro.Com active products - switches - lp-sgw2400 3.9 igmp snooping per default – and when enabled - igmp snooping will function in each statically defined vlan (i.E. Those vlans that are stored in non-volatile configuration memory). The igmp snooping module will listen to ip multicast router igm...
Www.Lanpro.Com active products - switches - lp-sgw2400 8 3.12 filter sets the source ip filter per port to block unwanted access. Figure 13 3.13 rate limit the rate limit can prevent the saome customer to occupy a huge bandwidth which may affect the normal network using. An isp or wisp application as...
Www.Lanpro.Com active products - switches - lp-sgw2400 9 chapter 4 monitoring guide d 4.1 statistics overview display all the port current transmit information and receive information. Figure 16 4.2 detailed statistics display the port current transmit detailed information and receive detailed infor...
Www.Lanpro.Com active products - switches - lp-sgw2400 10 4.4 rstp port status display the port rstp port status. Figure 19 4.5 igmp status display igmp status. Figure 20 type of diagnostics. “full” comprises cable length and full anomaly check, “anomaly” comprises full anomaly check and “terminatio...
Www.Lanpro.Com active products - switches - lp-sgw2400 11 chapter 5 maintenance guide e 5.1 warm restart warm restart: click “yes” to start restart the switch. Figure 22 5.2 factory default restore factory configuration: click “yes” to start restore factory default configuration. Notice: please do log...
Www.Lanpro.Com active products - switches - lp-sgw2400 12 6.1 com port set-up to use the command line interface you may connect a pc com port to the rs-232 connector and activate a terminal program, e.G. Hyperterminal under windows. The com port must be set up to run 8 data bits, 1 stop bit, no pari...
Www.Lanpro.Com active products - switches - lp-sgw2400 13 6.3 login/logout procedures to get access to the cli you must login by entering a password. You will automatically be queried about the password. The password is configurable. The password check may be disabled by setting the password to an em...
Www.Lanprod.Com active products - switches - lp-sgw2400 14 6.5 example 2 please open the hyperterminal console. Configure the hyper terminal. Figure 31 input the password an press hit enter you will be located at the console root, indicated by the symbol > in order to know the available commands in t...
