1. DL manuals
  2. Lantronix
  3. Server
  4. MatchPort AR
  5. Integration Manual

Lantronix MatchPort AR Integration Manual

Manual is about: MatchPort AR embedded device server

Summary of MatchPort AR

  • Page 1

    Matchport ar™ integration guide part number 900-481 revision a june 2007.

  • Page 2

    Matchport ar integration guide 2 copyright and trademark © 2007 lantronix. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of lantronix. Printed in the united states of america. Matchport ar, with i...

  • Page 3

    Matchport ar™ integration guide 3 disclaimer and revisions operation of this equipment in a residential area is likely to cause interference to other devices, in which case the user, at his or her own expense, will be required to take whatever measures may be required to correct the interference. No...

  • Page 4: Contents

    Matchport ar™ integration guide 4 contents 1: introduction 6 about the integration guide________________________________________________6 additional documentation _________________________________________________6 2: description and specifications 7 matchport ar block diagram _______________________...

  • Page 5: List of Figures

    Matchport ar™ integration guide 5 list of figures figure 2-1. Matchport ar top and front views .......................................................................... 8 figure 2-2. Matchport ar block diagram.................................................................................... 8 fig...

  • Page 6

    Matchport ar™ integration guide 6 1 1 : : i i n n t t r r o o d d u u c c t t i i o o n n about the integration guide this guide provides the information needed to integrate the matchport ar™ device server within another product. The intended audiences are the engineers responsible for integrating t...

  • Page 7

    Matchport ar™ integration guide 7 2 2 : : d d e e s s c c r r i i p p t t i i o o n n a a n n d d s s p p e e c c i i f f i i c c a a t t i i o o n n s s the matchport ar embedded device server is a complete network-enabling solution on a 1.75"x1.75" pcb. This miniature device server empowers origin...

  • Page 8

    2:description and specifications matchport ar™ integration guide 8 figure 2-1. Matchport ar top and front views matchport ar block diagram the following drawing is a block diagram of the matchport ar showing the relationships of the components. Figure 2-2. Matchport ar block diagram.

  • Page 9

    2:description and specifications matchport ar™ integration guide 9 matchport ar pinouts there are two headers of 1x20, 2-mm pin spacing. The odd row header is designated as p1; pins are numbered 1 to 39. The even row header is designated as p2; pins are numbered 2 to 40. Pin # name function pin # na...

  • Page 10

    2:description and specifications matchport ar™ integration guide 10 there is an on board capacitor, 0.1uf to ground, at the resetin# to filter out transient voltages. However, as always, it is a good practice to have resetin# trace on the target board as short as possible to avoid reset occurrences ...

  • Page 11

    2:description and specifications matchport ar™ integration guide 11 ethernet led connections the e_linkled and e_actled signals are driven by the phy. They are active low. Recommended connections on the target board are shown below. Figure 2-4. Recommended led connections warning: the matchport ar h...

  • Page 12

    2:description and specifications matchport ar™ integration guide 12 table 2-2. Jp6 rs422/485 connections on demo board matchport ar signal (logic) description rs485 signal jp6 pin db25 4 wire db25 2 wire db9 4 wire db9 2 wire txd1 data out tx+485 4 14 14 7 7 txd1 data out tx-485 3 15 15 3 3 rxd1 dat...

  • Page 13

    2:description and specifications matchport ar™ integration guide 13 figure 2-7. Separate rs422 transceivers for 2-wire and 4-wire setups to protect the matchport ar and circuitry on the target board against esd at serial ports, the selected transceiver(s) should have rs232/422/485 bus-pin esd protec...

  • Page 14

    2:description and specifications matchport ar™ integration guide 14 bootp_en# the bootp_en# pin performs two functions simultaneously. It drives an optional external diagnostics led to indicate the status of the bootloader. It also serves as input to enable booting from the network when no valid fw ...

  • Page 15

    2:description and specifications matchport ar™ integration guide 15 figure 2-8. Bootp_en# application circuit electrical specifications caution: stressing the device above the rating listed in this table may cause permanent damage to the matchport ar. Exposure to absolute maximum rating conditions f...

  • Page 16

    2:description and specifications matchport ar™ integration guide 16 specifications table 2-5. Specifications category matchport ar cpu lantronix dstni-fx 32-bit microprocessor, 166 mhz internal bus, 83 mhz external bus memory 4 mbits flash and 8 mbits sdram, and can be expanded. Please contact your ...

  • Page 17

    2:description and specifications matchport ar™ integration guide 17 dimensions the matchport ar dimensions are shown in the following diagrams: figure 2-9. Side views.

  • Page 18

    2:description and specifications matchport ar™ integration guide 18 figure 2-10. Top view figure 2-11. Bottom view.

  • Page 19

    2:description and specifications matchport ar™ integration guide 19 recommended pcb layout the hole pattern and mounting dimensions for the matchport ar device server are shown in the following drawing: figure 2-12. Pcb layout (top view) to optimize noise and cross-talk reduction, noise immunity, an...

  • Page 20

    2:description and specifications matchport ar™ integration guide 20 product information label the product information label contains important information about your specific unit, such as its product id (name), bar code, part number, and mac address. Figure 2-13. Product label mac address revision ...

  • Page 21

    Matchport ar™ integration guide 21 3 3 : : d d e e m m o o n n s s t t r r a a t t i i o o n n k k i i t t using a matchport ar sample and the matchport demonstration kit, you can get familiar with the product and understand how to integrate the matchport ar into a given product design. Contents of ...

  • Page 22

    3:demonstration kit matchport ar™ integration guide 22 serial interfaces the demo board has rs-232/422/485 transceivers, one per port. However, note that only serial port 1 supports rs232/rs422/485 on matchport ar. The table below lists the rs232 signals and corresponding pins on the demo board. All...

  • Page 23

    3:demonstration kit matchport ar™ integration guide 23 configuration switch bank table 3-3. Demo board jp1 jumper configuration jp1 pin/signal jp1 pin/signal function 1/cp1 2/led12 jumper 1-2, cp1 controls led12 3/cp2 4/led11 jumper 3-4, cp2 controls led11 5/cp3 6/led10 jumper 5-6, cp3 controls led1...

  • Page 24

    3:demonstration kit matchport ar™ integration guide 24 table 3-5. Demo board jp5 jumper configuration pin/signal pin/signal function 1/3v3 2/3v3_uut matchport uut power input jumper for current measurement. Jumper 1- 2 must be installed to provide power to uut. If using cps for any combination of th...

  • Page 25

    3:demonstration kit matchport ar™ integration guide 25 demo board schematics figure 3-2. Demo board block diagram * depends on module used..

  • Page 26

    3:demonstration kit matchport ar™ integration guide 26 figure 3-3. Schematic.

  • Page 27

    3:demonstration kit matchport ar™ integration guide 27 figure 3-3. Schematic, continued.

  • Page 28

    3:demonstration kit matchport ar™ integration guide 28 figure 3-3. Schematic, continued.

  • Page 29

    Matchport ar™ integration guide 29 a a : : c c o o m m p p l l i i a a n n c c e e a a n n d d w w a a r r r r a a n n t t y y i i n n f f o o r r m m a a t t i i o o n n compliance information (according to iso/iec guide 17050-1, 17050-2 and en 45014) manufacturer’s name & address: lantronix 15353 ...

  • Page 30

    A:compliance and warranty information matchport ar™ integration guide 30 manufacturer’s contact: director of quality assurance, lantronix 15353 barranca parkway, irvine, ca 92618 usa tel: 949-453-3990 fax: 949-453-3995 warranty lantronix warrants each lantronix product to be free from defects in mat...