Part number 900-532 revision b december 2011 matchport b/g pro integration guide.
Matchport b/g pro integration guide 2 copyright and trademark © 2011 lantronix. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of lantronix. Printed in the united states of america. Matchport®, wit...
Matchport b/g pro integration guide 3 reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv techni...
Matchport b/g pro integration guide 4 contents contents ______________________________________________________________ 4 list of figures __________________________________________________________ 5 list of tables ___________________________________________________________ 5 1: introduction 6 about t...
Matchport b/g pro integration guide 5 list of figures figure 2-1. Matchport b/g pro block diagram _____________________________________ 8 figure 2-2. Connection diagram to an rj45 jack ________________________________ 10 figure 2-3. Recommended led connections ____________________________________ 11...
Matchport b/g pro integration guide 6 1: introduction about the integration guide this guide provides the information needed to integrate the matchport b/g pro™ device server within another product. The intended audiences are the engineers responsible for integrating the matchport b/g pro into their...
Matchport b/g pro integration guide 7 2: description and specifications the matchport b/g pro embedded device server is a complete network-enabling solution on a 1.75"x1.75" pcb. This miniature device server empowers original equipment manufacturers (oems) to go to market quickly and easily with net...
2: description and specifications matchport b/g pro integration guide 8 figure 2-1. Matchport b/g pro block diagram.
2: description and specifications matchport b/g pro integration guide 9 matchport b/g pro pinouts there are two headers of 1x20, 2-mm pin spacing. The odd row header is designated as p1; pins are numbered 1 to 39. The even row header is designated as p2; pins are numbered 2 to 40. Pin # name dir act...
2: description and specifications matchport b/g pro integration guide 10 note: to minimize noises as well as voltage drops at the connection, we recommend direct connection of 3.3v and ground on the matchport b/g pro to 3.3v power and ground planes of the target board in place of heavy trace routing...
2: description and specifications matchport b/g pro integration guide 11 ethernet led connections the e_linkled and e_actled signals are driven by the phy. They are active low. Recommended connections on the target board are shown below. Figure 2-3. Recommended led connections warning: the matchport...
2: description and specifications matchport b/g pro integration guide 12 figure 2-5. Reverse-sma to u.Fl (p/n 500-180-r) figure 2-6. U.Fl to u.Fl cable (p/n 500-181-r) note: the antenna cable is included in the matchport b/g pro sample. For production, it can be purchased from lantronix or a cable s...
2: description and specifications matchport b/g pro integration guide 13 serial input/output the unit has two rs232 compatible serial ports supporting data rates up to 230 kbps. They include dedicated rts and cts hardware flow control signals. Configurable pins can be configured to function as dtr a...
2: description and specifications matchport b/g pro integration guide 14 figure 2-9. Separate rs232/422 transceivers.
2: description and specifications matchport b/g pro integration guide 15 figure 2-10. Separate rs422 transceivers for 2-wire and 4-wire setups to protect the matchport b/g pro and circuitry on the target board against esd at serial ports, the selected transceiver(s) should have rs232/422/485 bus-pin...
2: description and specifications matchport b/g pro integration guide 16 bootp_en# the bootp_en# pin performs two functions simultaneously. It drives an optional external diagnostics led to indicate the status of the bootloader. It also serves as input to enable booting from the network when no vali...
2: description and specifications matchport b/g pro integration guide 17 figure 2-11. Bootp_en# application circuit electrical specifications caution: stressing the device above the rating listed in this table may cause permanent damage to the matchport b/g pro. Exposure to absolute maximum rating c...
2: description and specifications matchport b/g pro integration guide 18 parameter symbol min typical max units e_linkled, e_actled current drive (sink) i eled 12 ma (see note below) w_linkled 10 ma notes: do not connect a pull-down resistor on e_linkled and e_actled. All pins are not 5v-tolerant. W...
2: description and specifications matchport b/g pro integration guide 19 category matchport b/g pro flow control xon/xoff (software), cts/rts (hardware), none network interfaces ethernet 10/100 base tx with auto negotiation, and hp auto mdix ieee802.11bg, with ieee802.11i/psk/eap security. Protocols...
2: description and specifications matchport b/g pro integration guide 20 figure 2-13. Top view figure 2-14. Bottom view.
2: description and specifications matchport b/g pro integration guide 21 recommended pcb layout the hole pattern and mounting dimensions for the matchport b/g pro device server are shown in the following drawing: figure 2-15. Pcb layout (top view) note: if a socket is used for product development pu...
2: description and specifications matchport b/g pro integration guide 22 product information label the product information label contains important information about your specific unit, such as its product id (name), bar code, part number, and mac address. Figure 2-16. Product label mac address revi...
Matchport b/g pro integration guide 23 3: demonstration kit using a matchport b/g pro sample and the matchport demonstration kit, you can get familiar with the product and understand how to integrate the matchport b/g pro into a given product design. Contents of the kit the matchport demonstration k...
3: demonstration kit matchport b/g pro integration guide 24 serial interfaces the demo board has rs-232/422/485 transceivers, one per port. However, note that only serial port 1 supports rs232/rs422/485 on matchport b/g pro. The table below lists the rs232 signals and corresponding pins on the demo ...
3: demonstration kit matchport b/g pro integration guide 25 configuration switch bank table 3-3. Demo board jp1 jumper configuration jp1 pin/signal jp1 pin/signal function 1/cp1 2/led12 jumper 1-2, cp1 controls led12 3/cp2 4/led11 jumper 3-4, cp2 controls led11 5/cp3 6/led10 jumper 5-6, cp3 controls...
3: demonstration kit matchport b/g pro integration guide 26 jp7 pin/signal jp7 pin/signal function b/g pro 13/cp5 14/dtrb jumper 13-14, cp5 drives dtr to rs232 transceiver. 15/cp6 16/dcdb jumper 15-16, cp6 receives dcd from rs232 transceiver. Note: cp allocation in the tables above is the most strai...
3: demonstration kit matchport b/g pro integration guide 27 demo board layout figure 3-1. Matchport demo board layout.
3: demonstration kit matchport b/g pro integration guide 28 demo board schematics figure 3-2. Demo board block diagram.
3: demonstration kit matchport b/g pro integration guide 29 figure 3-3. Schematic.
3: demonstration kit matchport b/g pro integration guide 30 figure 3-3. Schematic, continued.
3: demonstration kit matchport b/g pro integration guide 31 figure 3-3. Schematic, continued.
Matchport b/g pro integration guide 32 a: compliance (according to iso/iec guide 17050-1, 17050-2 and en 45014) manufacturer’s name & address: lantronix 167 technology drive, irvine, ca 92618 usa product name model: matchport b/g pro embedded device server conforms to the following standards or othe...
Matchport b/g pro integration guide 33 b: warranty for details on the lantronix warranty replacement policy, go to our web site at www.Lantronix.Com/support/warranty.