1. DL manuals
  2. Lantronix
  3. Gateway
  4. PREMIERWAVE XC HSPA+
  5. User Manual

Lantronix PREMIERWAVE XC HSPA+ User Manual

Other manuals for PREMIERWAVE XC HSPA+: User Manual
Manual is about: INTELLIGENT GATEWAY

Summary of PREMIERWAVE XC HSPA+

  • Page 1

    Part number 900-678-r revision a may 2013 premierwave xc hspa+ user guide preliminary draft preliminary draft.

  • Page 2

    Premierwave xc hspa+ user guide 2 copyright & trademark © 2013 lantronix, inc. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of lantronix. Lantronix® registered trademark of lantronix, inc. Device...

  • Page 3

    Premierwave xc hspa+ user guide 3 table of contents list of figures _____________________________________________________________ 9 list of tables _____________________________________________________________ 10 1: using this guide 12 purpose and audience ____________________________________________...

  • Page 4

    Premierwave xc hspa+ user guide 4 6: network settings 32 network 1 (eth0) interface settings ____________________________________________ 32 to configure network interface settings ____________________________________ 33 to view network interface status _________________________________________ 33 n...

  • Page 5

    Premierwave xc hspa+ user guide 5 to configure tunnel accept mode settings __________________________________ 51 connect mode ________________________________________________________ 51 to configure tunnel connect mode settings ________________________________ 52 disconnect mode ____________________...

  • Page 6

    Premierwave xc hspa+ user guide 6 ssh client users ______________________________________________________ 68 to configure ssh settings ______________________________________________ 69 ssl settings _____________________________________________________________ 69 certificate and key generation ______...

  • Page 7

    Premierwave xc hspa+ user guide 7 to view thread information ______________________________________________ 81 clock ___________________________________________________________________ 81 to specify clock setting method __________________________________________ 82 system settings __________________...

  • Page 8

    Premierwave xc hspa+ user guide 8 17: branding the premierwave xc hspa+ 96 web manager customization ________________________________________________ 96 short and long name customization __________________________________________ 97 to customize short or long names __________________________________...

  • Page 9

    Premierwave xc hspa+ user guide 9 list of figures figure 2-1 premierwave xc hspa+product label ______________________________________ 17 figure 3-1 premierwave xc hspa+ top/front view_____________________________________ 19 figure 3-2 premierwave male db9 dte serial ports ___________________________...

  • Page 10

    Premierwave xc hspa+ user guide 10 list of tables table 3-6 premierwave leds and descriptions ________________________________________ 21 table 3-7 cellular signal strength indicator ___________________________________________ 21 table 3-8 diagnostic led indications _________________________________...

  • Page 11

    Premierwave xc hspa+ user guide 11 table 12-1 ssh server host keys ___________________________________________________ 66 table 12-2 ssh client known hosts _________________________________________________ 67 table 12-3 ssh server authorized users _____________________________________________ 68 tab...

  • Page 12: Using This Guide

    Premierwave xc hspa+ user guide 12 1: using this guide purpose and audience this guide provides the information needed to configure, use, and update the premierwave xc hspa+. It is intended for software developers and system integrators who are installing this product into their designs. Summary of ...

  • Page 13

    1: using this guide premierwave xc hspa+ user guide 13 caution: to avoid electric shock and for the device to work properly, do not allow cleaning solution to get inside the device, specifically the interface port connectors, power connector, or power cord. Do not immerse the device in any liquid. A...

  • Page 14: Introduction

    Premierwave xc hspa+ user guide 14 2: introduction premierwave xc hspa+ is a multi-port device server offering ethernet and cellular connectivity for remote access and easy management of machines or equipment over the network and across the internet. Key features power supply: 9-30vdc input voltage ...

  • Page 15

    2: introduction premierwave xc hspa+ user guide 15 arp, http, https, smtp auth, snmp v1/v2c/v3, modbus tcp, udp/ip, tcp/ip, ssh, ssl, tls, rss, upnp, icmp, bootp, dhcp, auto ip, telnet, sntp, ftp, ftps, dns, tftp, xml and syslog for network communications and management. Tftp for uploading/downloadi...

  • Page 16

    2: introduction premierwave xc hspa+ user guide 16 addresses and port numbers hardware address the hardware address is also referred to as the ethernet address, physical address, or mac address. Sample hardware address: 00-80-a3-14-1b-18 00:80:a3:14:1b:18 ip address every device connected to an ip n...

  • Page 17

    2: introduction premierwave xc hspa+ user guide 17 figure 2-1 premierwave xc hspa+product label part number revision serial number country of origin data code imei text preliminary draft preliminary draft.

  • Page 18

    Premierwave xc hspa+ user guide 18 3: installation of premierwave xc hspa+ this chapter describes how to install the premierwave xc hspa+ device server. It contains the following sections: package contents user-supplied items hardware components installing the premierwave xc hspa+ package contents t...

  • Page 19

    3: installation of premierwave xc hspa+ premierwave xc hspa+ user guide 19 figure 3-1 premierwave xc hspa+ top/front view the premierwave has two male db9 serial ports that support rs-232/422/485. Figure 3-2 shows the front view of the device. The default serial port settings are 9600 baud, 8 bits, ...

  • Page 20

    3: installation of premierwave xc hspa+ premierwave xc hspa+ user guide 20 figure 3-2 premierwave male db9 dte serial ports figure 3-3 premierwave pinout configuration for rs-232 figure 3-4 premierwave pinout configuration for full duplex rs-422/485 (4-wire figure 3-5 premierwave pinout configuratio...

  • Page 21

    3: installation of premierwave xc hspa+ premierwave xc hspa+ user guide 21 ethernet leds the ethernet port has two leds that indicate the status of the connection as follows: left led green on 100mbps link green blink 100mbps activity amber on 10mbps link amber blink 10mbps activity right led green ...

  • Page 22

    3: installation of premierwave xc hspa+ premierwave xc hspa+ user guide 22 table 3-8 diagnostic led indications notes: for table 3-8 above, a “long” blink is 0.7 seconds of light followed by 0.3 seconds of no light. A “short” blink is a light that is on for only 0.2 seconds and followed by 0.2 secon...

  • Page 23

    3: installation of premierwave xc hspa+ premierwave xc hspa+ user guide 23 back panel on the premierwave is a power 1 plug and rj-45 ethernet port as shown in table 3-9 . Table 3-9 premierwave bottom/back panel view table 3-10 premierwave xc hspa+ connections (side) installing the premierwave xc hsp...

  • Page 24

    3: installation of premierwave xc hspa+ premierwave xc hspa+ user guide 24 perform the following steps to install your device: 1. With the power unplugged, insert your sim card. 2. Connect an rj-45 ethernet cable between the unit and your ethernet network. 3. Connect the antennas to the sma connecto...

  • Page 25: Using Deviceinstaller

    Premierwave xc hspa+ user guide 25 4: using deviceinstaller this chapter covers the steps for locating a premierwave xc hspa+ unit and viewing its properties and device details. Deviceinstaller is a free utility program provided by lantronix that discovers, configures, upgrades and manages lantronix...

  • Page 26

    4: using deviceinstaller premierwave xc hspa+ user guide 26 group configurable field. Enter a group to categorize the . Double-click the field, type in the value, and press enter to complete. This group name is local to this pc and is not visible on other pcs or laptops using deviceinstaller. Commen...

  • Page 27

    Premierwave xc hspa+ user guide 27 5: configuration using web manager this chapter describes how to configure premierwave using web manager, the lantronix browser-based configuration tool. The unit’s configuration is stored in nonvolatile memory and is retained without power. All changes take effect...

  • Page 28

    5: configuration using web manager premierwave xc hspa+ user guide 28 device status page the device status page is the first to appear after you log into web manager. The device status page also appears when you click status in web manager. Figure 5-1 premierwave xc hspa+ home pages note: the logout...

  • Page 29

    5: configuration using web manager premierwave xc hspa+ user guide 29 web manager components the layout of a typical web manager page is below. Figure 5-2 components of the web manager page menu bar links to subpages items to configure header information and help area configuration and/or status are...

  • Page 30

    5: configuration using web manager premierwave xc hspa+ user guide 30 web manager pages have these sections: the menu bar appears at the left side of the page. The menu bar lists the names of the pages available. To bring up a page, click it in the menu bar. Links near the top of many pages, such as...

  • Page 31

    5: configuration using web manager premierwave xc hspa+ user guide 31 discovery allows you to view and modify the configuration and statistics for device discovery. 83 dns shows the current configuration of the dns subsystem and the dns cache. 59 email shows email statistics and lets you clear the e...

  • Page 32: Network Settings

    Premierwave xc hspa+ user guide 32 6: network settings the network settings show the status of the ethernet interface/link and let you configure the settings on the device. Interface settings are related to the configuration of the ip and related protocols. Link settings are related to the physical ...

  • Page 33

    6: network settings premierwave xc hspa+ user guide 33 to configure network interface settings using web manager to modify ethernet (eth0) settings, click network on the menu and select network 1 -> interface -> configuration . Using the cli to enter the eth0 command level: enable -> config -> if 1 ...

  • Page 34

    6: network settings premierwave xc hspa+ user guide 34 to view ethernet (eth0) status, click network on the menu and select network 1 -> interface -> status . Network 1 (link) settings physical link parameters can be configured for an ethernet (eth0) network interface (see table 6-2 ). Table 6-2 net...

  • Page 35

    6: network settings premierwave xc hspa+ user guide 35 network 1 (failover) premierwave xc hspa+ provides basic ethernet to cellular failover, in the form of a "dead remote host reachability" mechanism (essentially a ping against a known host). If the remote host is determined to be not reachable, t...

  • Page 36

    6: network settings premierwave xc hspa+ user guide 36 to configure network 2 (cellular interface) settings using web manager to modify network 2 cellular interface information, click network on the menu and select network 2 > interface > configuration . Using the cli to enter the cellular command l...

  • Page 37

    6: network settings premierwave xc hspa+ user guide 37 to configure link settings using web manager to modify network 2 cellular interface information, click network on the menu and select network 2 > link > configuration . Using the cli to enter the link command level: enable -> if 2 -> link using ...

  • Page 38

    6: network settings premierwave xc hspa+ user guide 38 to configure gateway wan settings using web manager to modify gateway wan information, click gateway on the menu and select configuration > wan . Using the cli to enter the gateway command level: enable -> config -> gateway using xml include in ...

  • Page 39

    6: network settings premierwave xc hspa+ user guide 39 using the cli to enter the gateway command level: enable -> config -> gateway -> port forwarding rule number > using xml include in your file: forwarding" instance=""> static routes allows the user to add routes to the device routing table. Tabl...

  • Page 40

    6: network settings premierwave xc hspa+ user guide 40 dhcp server allows the user to configure the device as a dhcp server. Table 6-7 dhcp settings to configure gateway dhcp server settings using web manager to modify gateway dhcp server information, click gateway on the menu and select configurati...

  • Page 41: Cellular

    Premierwave xc hspa+ user guide 41 7: cellular the cellular page displays the configuration and status for the cellular module. To configure cellular settings using web manager click cellular on the menu. Using the cli to enter the cellular command level: enable -> config -> cellular using xml inclu...

  • Page 42: Action Settings

    Premierwave xc hspa+ user guide 42 8: action settings actions can be configured for alarms and reports available in the premierwave. Alarms and reports premierwave xc hspa+ updates the action settings page to display and configure the alarms. The following alarm and report acations are available in ...

  • Page 43

    8: action settings premierwave xc hspa+ user guide 43 to configure action settings using web manager to modify action information, click action on the menu and select a specific action from the drop-down menu. Alarms and reports (on page 42) lists the options. Using the cli to enter the link command...

  • Page 44

    8: action settings premierwave xc hspa+ user guide 44 digital input table 8-2 contain additional configuration options for digital input 1 and digital input 2 settings: table 8-2 digital input settings to configure digital input settings using web manager to modify digital input information, click d...

  • Page 45: Line and Tunnel Settings

    Premierwave xc hspa+ user guide 45 9: line and tunnel settings the premierwavehas two tunnels through which you may view statistics or configure the accept mode. The modbus configuration page allows configuration of modbus servers listening on the tcp ports. The premierwave contains two lines . All ...

  • Page 46

    9: line and tunnel settings premierwave xc hspa+ user guide 46 table 9-2 line command mode settings to configure line settings note: the following section describes the steps to view and configure line 1 settings; these steps apply to other line instances of the device. Data bits set the number of d...

  • Page 47

    9: line and tunnel settings premierwave xc hspa+ user guide 47 using web manager to configure a specific line, click line in the menu and select line 1 -> configuration ( table 9-1 ). To configure a specific line in command mode, click line in the menu and select line 1 -> command mode ( table 9-2 )...

  • Page 48

    9: line and tunnel settings premierwave xc hspa+ user guide 48 table 9-3 tunnel serial settings to configure tunnel serial settings using web manager to configure the serial settings for a specific tunnel, click tunnel in the menu and select tunnel 1 -> serial settings . Using the cli to enter tunne...

  • Page 49

    9: line and tunnel settings premierwave xc hspa+ user guide 49 to configure tunnel packing mode settings using web manager to configure the packing mode for a specific tunnel, click tunnel in the menu and select tunnel 1 -> packing mode . Using the cli to enter the tunnel 1 packing command level: en...

  • Page 50

    9: line and tunnel settings premierwave xc hspa+ user guide 50 local port set the port number for use as the network local port. The default local port number: tunnel 1 : 10001 tunnel 2 : 10002 protocol select the protocol type for use with accept mode: ssh ssl tcp (default protocol) tcp aes telnet ...

  • Page 51

    9: line and tunnel settings premierwave xc hspa+ user guide 51 to configure tunnel accept mode settings using web manager to configure the accept mode for a specific tunnel, click tunnel in the menu and select tunnel 1 -> accept mode . Using the cli to enter tunnel 1 accept mode command level: enabl...

  • Page 52

    9: line and tunnel settings premierwave xc hspa+ user guide 52 to configure tunnel connect mode settings using web manager to configure the connect mode for a specific tunnel, click tunnel in the menu and select tunnel 1 -> connect mode . Using the cli to enter the tunnel 1 connect mode command leve...

  • Page 53

    9: line and tunnel settings premierwave xc hspa+ user guide 53 table 9-7 tunnel disconnect mode settings to configure tunnel disconnect mode settings using web manager to configure the disconnect mode for a specific tunnel, click tunnel in the menu and select tunnel 1 -> disconnect mode . Using the ...

  • Page 54

    9: line and tunnel settings premierwave xc hspa+ user guide 54 to configure tunnel modem emulation settings using web manager to configure the modem emulation for a specific tunnel, click tunnel in the menu and select tunnel 1 -> modem emulation . Using the cli to enter the tunnel 1 modem command le...

  • Page 55

    9: line and tunnel settings premierwave xc hspa+ user guide 55 relay output note: when relay is energized/turned on, the relay is closed connecting both relay ports on the io connector through the relay. When the relay is turned off, the signal path is open, disconnecting the relay ports on the io c...

  • Page 56

    Premierwave xc hspa+ user guide 56 10: terminal and host settings predefined connections are available via telnet, ssh, or a serial port. A user can choose one of the presented options and the device automatically makes the predefined connection. Either the telnet, ssh, or serial port connection can...

  • Page 57

    10: terminal and host settings premierwave xc hspa+ user guide 57 to configure the terminal network connection using web manager to configure the terminal on network, click terminal on the menu and select network -> configuration . To configure the terminal on network, click line 1 on the menu and s...

  • Page 58

    10: terminal and host settings premierwave xc hspa+ user guide 58 host configuration table 10-2 host configuration to configure host settings note: the following section describes the steps to view and configure host 1 settings; these steps apply to other host instances of the device. Using web mana...

  • Page 59: 11: Services Settings

    Premierwave xc hspa+ user guide 59 11: services settings dns settings this section describes the active run-time settings for the domain name system (dns) protocol. The primary and secondary dns addresses come from the active interface. The static addresses from the network interface configuration s...

  • Page 60

    11: services settings premierwave xc hspa+ user guide 60 to configure ftp settings using web manager to configure ftp, click ftp in the menu. Using the cli to enter the ftp command level: enable -> config -> ftp using xml include in your file: syslog settings the syslog information shows the current...

  • Page 61

    11: services settings premierwave xc hspa+ user guide 61 using xml include in your file: http settings hypertext transfer protocol (http) is the transport protocol for communicating hypertext documents on the internet. Http defines how messages are formatted and transmitted. It also defines the acti...

  • Page 62

    11: services settings premierwave xc hspa+ user guide 62 to configure http settings using web manager to configure http settings, click http in the menu and select configuration . To view http statistics, click http in the menu and select statistics . Using the cli to enter the http command level: e...

  • Page 63

    11: services settings premierwave xc hspa+ user guide 63 to configure http authentication using web manager to configure http authentication, click http in the menu and select authentication . Using the cli to enter the http command level: enable -> config -> http using xml include in your file: ins...

  • Page 64

    11: services settings premierwave xc hspa+ user guide 64 snmp settings simple network management protocol (snmp) settings may be viewed and configured in this section. Table 11-7 snmp settings to configure snmp settings using web manager to configure snmp, click snmp in the menu. Using the cli to en...

  • Page 65

    11: services settings premierwave xc hspa+ user guide 65 outbound sms table 11-9 outbound sms settings to configure sms using web manager to view and configure inbound sms, click sms in the menu and select inbound . Using the cli to enter the command level: enable -> configure -> sms -> inbound usin...

  • Page 66: 12: Security Settings

    Premierwave xc hspa+ user guide 66 12: security settings the premierwave xc hspa+ device supports secure shell (ssh) and secure sockets layer (ssl). Ssh is a network protocol for securely accessing a remote device. Ssh provides a secure, encrypted communication channel between two hosts over a netwo...

  • Page 67

    12: security settings premierwave xc hspa+ user guide 67 note: ssh keys from other programs may be converted to the required premierwave format. Use open ssh to perform the conversion. Ssh client known hosts the ssh client known hosts are used by all applications that play the role of an ssh client....

  • Page 68

    12: security settings premierwave xc hspa+ user guide 68 table 12-3 ssh server authorized users ssh client users the ssh client users are used by all applications that play the role of an ssh client. Specifically tunneling in connecta mode. To configure the premierwave as an ssh client, an ssh clien...

  • Page 69

    12: security settings premierwave xc hspa+ user guide 69 to configure ssh settings using web manager to configure ssh, click ssh in the menu. Using the cli to enter the ssh command level: enable -> ssh using xml ssl settings secure sockets layer (ssl) is a protocol for managing the security of data ...

  • Page 70

    12: security settings premierwave xc hspa+ user guide 70 table 12-5 certificate and key generation settings to create a new credential using web manager to create a new credential, click ssl in the menu and select credentials . Using the cli to enter the ssl command level: enable -> ssl to enter the...

  • Page 71

    12: security settings premierwave xc hspa+ user guide 71 certificate upload settings ssl certificates identify the premierwave to peers. Certificate and key pairs can be uploaded to the premierwave through either the cli or xml import mechanisms. Certificates can be identified on the premierwave by ...

  • Page 72

    12: security settings premierwave xc hspa+ user guide 72 trusted authorities one or more authority certificates are needed to verify a peer's identity. These certificates do not require a private key. To upload an authority certificate using web manager to upload an authority certificate, click ssl ...

  • Page 73

    Premierwave xc hspa+ user guide 73 13: maintenance and diagnostics settings filesystem settings use the file system to list, view, add, remove, and transfer files. The premierwave uses a flash file system to store files. File display it is possible to view the list of existing files, and to view the...

  • Page 74

    13: maintenance and diagnostics settings premierwave xc hspa+ user guide 74 file modification the premierwave allows for the creation and removal of files on its filesystem. Table 13-2 file modification settings file transfer files can be transferred to and from the premierwave via the tftp protocol...

  • Page 75

    13: maintenance and diagnostics settings premierwave xc hspa+ user guide 75 to transfer or modify filesystem files using web manager to create a new file or directory, upload an existing file, copy or move a file, click filesystem in the menu and select browse . Using the cli to enter the filesystem...

  • Page 76

    13: maintenance and diagnostics settings premierwave xc hspa+ user guide 76 icmp settings table 13-5 icmp network stack settings to configure icmp network stack settings using web manager to configure icmp protocol settings, click protocol stack in the menu and select icmp . Using the cli to enter t...

  • Page 77

    13: maintenance and diagnostics settings premierwave xc hspa+ user guide 77 smtp settings table 13-7 smtp network stack settings to configure smtp network stack settings using web manager to configure smtp protocol settings, click protocol stack in the menu and select smtp . Using the cli to enter t...

  • Page 78

    13: maintenance and diagnostics settings premierwave xc hspa+ user guide 78 diagnostics the premierwave has several tools for diagnostics and statistics. Various options allow for the configuration or viewing of ip socket information, ping, traceroute, memory, and processes. Hardware to view hardwar...

  • Page 79

    13: maintenance and diagnostics settings premierwave xc hspa+ user guide 79 to ping a remote host using web manager to ping a remote host, click diagnostics in the menu and select ping . Using the cli to enter the command level: enable, ping using xml not applicable. Traceroute here you can trace a ...

  • Page 80

    13: maintenance and diagnostics settings premierwave xc hspa+ user guide 80 to configure the diagnostic log output using web manager to configure the diagnostic log output, click diagnostics in the menu and select log . Using the cli to enter the command level: enable -> config -> diagnostics -> log...

  • Page 81

    13: maintenance and diagnostics settings premierwave xc hspa+ user guide 81 using the cli to enter the command level: enable, show processes using xml include in your file: threads the premierwave threads information shows details of threads in the ltrx_evo task which can be useful for technical exp...

  • Page 82

    13: maintenance and diagnostics settings premierwave xc hspa+ user guide 82 to specify clock setting method using web manager to view thread information, click clock in the menu. Using the cli to enter the command level: enable -> config -> clock using the xml include in your file: system settings t...

  • Page 83

    13: maintenance and diagnostics settings premierwave xc hspa+ user guide 83 using xml include in your file: discovery and query port the current statistics and configuration options for device discovery, including query port are available for the premierwave. Table 13-13 discovery settings to config...

  • Page 84: 14: Advanced Settings

    Premierwave xc hspa+ user guide 84 14: advanced settings email settings view and configure email alerts relating to events occurring within the system. Table 14-1 email configuration to view, configure and send email note: the following section describes the steps to view and configure email 1 setti...

  • Page 85

    14: advanced settings premierwave xc hspa+ user guide 85 using the cli to enter email command level: enable -> email 1 using xml include in your file: command line interface settings the command line interface settings allow you to control how users connect to and interact with the premierwave's com...

  • Page 86

    14: advanced settings premierwave xc hspa+ user guide 86 telnet settings the telnet settings control cli access to the premierwave over the telnet protocol. Table 14-3 telnet settings to configure telnet settings using web manager to configure telnet settings, click cli in the menu and select config...

  • Page 87

    14: advanced settings premierwave xc hspa+ user guide 87 to configure ssh settings using web manager to configure ssh settings, click cli in the menu and select configuration . Using the cli to enter the ssh command level: enable -> config -> cli -> ssh using xml include in your file: and xml settin...

  • Page 88

    14: advanced settings premierwave xc hspa+ user guide 88 to export configuration in xml format using web manager to export configuration format, click xml in the menu and select export configuration . Using the cli to enter the xml command level: enable -> xml using xml not applicable. Xml: export s...

  • Page 89

    14: advanced settings premierwave xc hspa+ user guide 89 using xml not applicable. Xml: import configuration here you can import a system configuration from an xml file. The xml data can be imported from a file on the file system or pasted into a cli session. The groups to import can be specified at...

  • Page 90

    14: advanced settings premierwave xc hspa+ user guide 90 using xml not applicable. Preliminary draft preliminary draft.

  • Page 91: 15: Security In Detail

    Premierwave xc hspa+ user guide 91 15: security in detail public key infrastructure public key infrastructure (pki) is based on an encryption technique that uses two keys: a public key and private key. Public keys can be used to encrypt messages which can only be decrypted using the private key. Thi...

  • Page 92

    15: security in detail premierwave xc hspa+ user guide 92 through any number of intermediate authorities, ultimately to the agent that needs to prove its authenticity. Obtaining certificates signed certificates are typically obtained from well-known cas, such as verisign. This is done by submitting ...

  • Page 93

    15: security in detail premierwave xc hspa+ user guide 93 steel belted radius steel belted radius is a commercial radius server from juniper networks that provides a gui administration interface. It also provides a certificate request and self-signed certificate generator. The self-signed certificat...

  • Page 94: 16: Updating Firmware

    Premierwave xc hspa+ user guide 94 16: updating firmware obtaining firmware obtain the most up-to-date firmware and release notes for the unit from the lantronix web site ( www.Lantronix.Com/support/downloads/ ) or by using anonymous ftp ( ftp://ftp.Lantronix.Com/ ). Loading new firmware through web...

  • Page 95

    16: updating firmware premierwave xc hspa+ user guide 95 device will automatically reboot afterwards. 6. Close and reopen the web manager internet browser to view the device’s updated web pages. Note: you may need to increase http max bytes in some cases where the browser is sending data aggressivel...

  • Page 96

    Premierwave xc hspa+ user guide 96 17: branding the premierwave xc hspa+ this chapter describes how to brand your premierwave by using web manager and command line interface (cli). It contains the following sections on customization: web manager customization short and long name customization web ma...

  • Page 97

    17: branding the premierwave xc hspa+ premierwave xc hspa+ user guide 97 short and long name customization you can customize the short and long names in your premierwave. The names display in the cli show command and in the system web page in the current configuration table. The short name is used f...

  • Page 98

    Premierwave xc hspa+ user guide 98 appendix a: technical specifications network cellular umts/hspa+ (850/800/900/1900/2100 mhz) gsm/gprs/edge (850/900/1800/1900 mhz) transfer rates - up to 14.4 mbps (downlink), up to 7.2mbps (uplink) 1 secure sim slot 2 x omni-directional penta-band antennas etherne...

  • Page 99

    Premierwave xc hspa+ user guide 99 usb connector 1 x usb type a host connector (usb 2.0) i/o interface input connection: sensors/events voltage acceptance: 0 to 30 vdc digital input event: user configurable optical: 1.5 kv output software: turn relay output on and off automatic event trigger: on or ...

  • Page 100

    Premierwave xc hspa+ user guide 100 management web browser (ssl option for secure login) cli (over serial ports, telnet, or ssh) xml configuration records via cli or ftp supports snmp version 2c software lantronix device server application suite deviceinstaller. Power input voltage: 9-30 vdc power c...

  • Page 101

    Premierwave xc hspa+ user guide 101 dimensions size: 9.4 cm (3.7 in) l x 10.9 cm (4.3 in) w x 3.0 cm (1.2 in) h weight: 0.44 kg (1.0 lb) warranty 5-year limited preliminary draft preliminary draft.

  • Page 102: Appendix B:  Compliance

    Premierwave xc hspa+ user guide 102 appendix b: compliance (according to iso/iec guide 17050-1, 17050-2 and en 45014) manufacturer's name & address: lantronix, inc. 167 technology drive, irvine, ca 92618 usa product name model: premierwave xc hspa+ this device complies with part 15 of the fcc rules....

  • Page 103

    Appendix b: compliance premierwave xc hspa+ user guide 103 conforms to the following standards or other normative documents: emissions fcc 15.107:2013 fcc 15.109:2013 fcc 22h:2011 fcc 24e:2011 rss-132:2005 rss-133:2009 en 301 489-24 en 301 489-7 en 301 511 (gsm & edge) en 301 908-1 en 301 908-2 (w-c...

  • Page 104

    Appendix b: compliance premierwave xc hspa+ user guide 104 manufacturer's contact: lantronix, inc. 167 technology drive, irvine, ca 92618 usa tel: 949-453-3990 fax: 949-450-7249 rohs notice all lantronix products in the following families are china rohs-compliant and free of the following hazardous ...

  • Page 105

    Premierwave xc hspa+ user guide 105 appendix c: technical support if you are unable to resolve an issue using the information in this documentation, please contact technical support: technical support us check our online knowledge base or send a question to technical support at http://www.Lantronix....

  • Page 106

    Premierwave xc hspa+ user guide 106 appendix d: binary to hexadecimal conversions many of the unit's configuration procedures require you to assemble a series of options (represented as bits) into a complete command (represented as a byte). The resulting binary value must be converted to a hexadecim...

  • Page 107

    Premierwave xc hspa+ user guide 107 figure d-2 windows scientific calculator 4. Click hex . The hexadecimal value appears. Figure d-3 hexadecimal values in the scientific calculator preliminary draft preliminary draft.

  • Page 108: For Windows Hosts

    Premierwave xc hspa+ user guide 108 appendix e: usb-cdc-acm device driver file for windows hosts the following file may be used to enable windows to recognize the usb-cdc-acm connection to the premierwave's usb device port. Create the linux-cdc-acm.Inf file on the windows host somewhere using the co...

  • Page 109

    Appendix e: usb-cdc-acm device driver file for windows hosts premierwave xc hspa+ user guide 109 ;----------------------------------------------------------------------- ; vista-64bit sections ;----------------------------------------------------------------------- [driverinstall.Ntamd64] include=md...