Lantronix xSenso 21R2 Quick Start Manual
WHAT’S
INSIDE
Rubber Feet (4)
xSenso™ 21R2
Wall Mount Bracket
Quick Start Guide
1 HARDWARE REVIEW
2 HARDWARE INSTALLATION
DIN Rail Mount
1. Angle the xSenso™ to position and
hook onto the DIN rail, then push it
back until it is flat against the DIN
rail. Push the orange clip upwards to
secure.
2. To remove from DIN rail, pull the
orange clip downward to unlock.
Angle and lift the xSenso™ upwards
to unlatch and remove.
Desktop, shelf, or table top installation
1. Place xSenso™ upside down on a smooth, flat surface.
2. Peel off the rubber feet from the adhesive strip and place them
adhesive-side down onto each corner of the xSenso™ device.
3. Turn the xSenso™ over so that it is resting on the rubber feet.
Mini USB Port
For management
and configuration of
xSenso™ device
Relay 1
Analog
Input 2
Relay 2
Analog
Input 1
9-30VDC Terminal
Block Power Input
9-30VDC Barrel Locking Power Input
NO = Normally Open
NC = Normally Closed
COM = Common Ground
Input Current I = 0-20mA
Input Voltage V = ±100mV, ±1V, ±10V
Excitation
P = 15VDC, 10mA per channel or 20mA total
= Ground
10/100 Mbps
(Auto-MDIX)
Ethernet port
Reset pin
Input 1 and
Input 2
status LED
Output 1 and
Output 2
status LED
WHAT’S
INSIDE
Rubber Feet (4)
xSenso™ 21R2
Wall Mount Bracket
Quick Start Guide
1 HARDWARE REVIEW
2 HARDWARE INSTALLATION
DIN Rail Mount
1. Angle the xSenso™ to position and
hook onto the DIN rail, then push it
back until it is flat against the DIN
rail. Push the orange clip upwards to
secure.
2. To remove from DIN rail, pull the
orange clip downward to unlock.
Angle and lift the xSenso™ upwards
to unlatch and remove.
Desktop, shelf, or table top installation
1. Place xSenso™ upside down on a smooth, flat surface.
2. Peel off the rubber feet from the adhesive strip and place them
adhesive-side down onto each corner of the xSenso™ device.
3. Turn the xSenso™ over so that it is resting on the rubber feet.
Mini USB Port
For management
and configuration of
xSenso™ device
Relay 1
Analog
Input 2
Relay 2
Analog
Input 1
9-30VDC Terminal
Block Power Input
9-30VDC Barrel Locking Power Input
NO = Normally Open
NC = Normally Closed
COM = Common Ground
Input Current I = 0-20mA
Input Voltage V = ±100mV, ±1V, ±10V
Excitation
P = 15VDC, 10mA per channel or 20mA total
= Ground
10/100 Mbps
(Auto-MDIX)
Ethernet port
Reset pin
Input 1 and
Input 2
status LED
Output 1 and
Output 2
status LED
WHAT’S
INSIDE
Rubber Feet (4)
xSenso™ 21A2
Wall Mount Bracket
Quick Start Guide
1 HARDWARE REVIEW
2 HARDWARE INSTALLATION
DIN Rail Mount
1. Angle the xSenso™ to position and
hook onto the DIN rail, then push it
back until it is flat against the DIN
rail. Push the orange clip upwards to
secure.
2. To remove from DIN rail, pull the
orange clip downward to unlock.
Angle and lift the xSenso™ upwards
to unlatch and remove.
Desktop, shelf, or table top installation
1. Place xSenso™ upside down on a smooth, flat surface.
2. Peel off the rubber feet from the adhesive strip and place them
adhesive-side down onto each corner of the xSenso device.
3. Turn the xSenso™ over so that it is resting on the rubber feet.
Mini USB Port
For management
and configuration of
xSenso™ device
Analog
Output 1
Analog
Input 2
Analog
Output 2
Analog
Input 1
9-30VDC Terminal
Block Power Input
9-30VDC Barrel Locking Power Input
Output Current I = 0-20mA
Output Voltage V = 0-10V
= Ground
Input Current I = 0-20mA
Input Voltage V = ±100mV, ±1V, ±10V
Excitation
P = 15VDC, 10mA per channel or 20mA total
= Ground
10/100 Mbps
(Auto-MDIX)
Ethernet port
Reset pin
Input 1 and
Input 2
status LED
Output 1 and
Output 2
status LED
WHAT’S
INSIDE
xSenso™ 21A2 Quick Start Guide
xSenso™ 21A2 Quick Start Guide
xSenso
™
21R2 Quick Start Guide
xSenso
™
21R2 Quick Start Guide