1. DL manuals
  2. Lassco Wizer
  3. Paper Cutters
  4. Spinnit EBM-S
  5. User Manual

Lassco Wizer Spinnit EBM-S User Manual

Summary of Spinnit EBM-S

  • Page 1

    Provided by http://www.Mybinding.Com http://www.Mybindingblog.Com lassco spinnit ebm-s paper drill user's manual.

  • Page 2

    Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference. Serial number: date of purchase: dealer: address: telephone number: 485 hague street, rochester, ny 14606 u.S.A. Tel: 585-436-1934 fax: 585-464-8665 www.Lasscowizer....

  • Page 3

    Table of contents introduction operating instructions maintenance trouble shooting guide introduction....................................................................... Shipping damage inspection............................................ Page 02 page 02 safety information safety instructions.....

  • Page 4

    Introduction shipping damage inspection page 02 thank you for your purchase of the spinnit ebm-s paper drill. Lassco-wizer has been designing and manufacturing proven performance equipment for the graphic arts, office, screen printing, sign, awards and engraving industries for over 60 years. We ask ...

  • Page 5

    Safety information page 03 all operators must read and understand the users manual and all other safety instruc- tions before using this equipment. If after reading the manual you are still uncertain about use, please contact a service technician for assistance. If you need contact information for a...

  • Page 6

    Setting up your machine loose materials inventory page 04 remove and inspect the following items: ebm2-1048: chip bag (1) ebms-115a: backgauge assembly (1) ebm-10: drill block (1) this item comes installed this item comes installed hollow drill bit (1) spin-eze: drill bit lubricant (1) cc-2: chip cl...

  • Page 7

    Setting up your machine back gauge assembly stop collars and paper side stop page 05 attach the backguage (ebms-115a) to the table by hooking the left end over the side iron (fm4-4003) on the side as shown in the accompanying pictures. Align both ends of the backgauge using the table scales so that ...

  • Page 8

    Setting up your machine page 06 your spinnit paper drill is now ready for use. With proper operation and maintenence, it will give you trouble free operation for years. Electrical start up making sure nothing is interfering with the drill bit, plug the cord set into a grounded 115v outlet. To turn t...

  • Page 9

    Operating instructions drill bit removal and installation page 07 remove the hole guard which is attached to the chuck. This is done by grasping the bent end and sliding the guard off. Step #1 using the chuck release key (ebm-32), insert the tapered end facing down into the chuck hole. With a clockw...

  • Page 10

    Operating instructions leveling the drill bits page 08 to level the drill bits to the table, first loosen the leveling knob on the right hand side of the machine as shown. Pull down on the handle to raise the table until the hollow drill bit is just touching the drill strip (ebm2-1034). Hold the han...

  • Page 11

    Operating instructions clearing the chips page 09 tips on drilling use a sharp bit at all times...Using a drill bit sharpener (lassco-wizer ms-1 recom- mended), sharpen your drill bits regularly. Apply light pressure when sharpening. Too much pressure may cause flaring of the tip. (once a drill bit ...

  • Page 12: Maintenance of This Machine.

    Maintenance page 10 every 6 months remove back panel and lubricate the lift pin with a good grade of light machine oil. Note: refer to your trouble shooting guide for problem solving caution: keep fingers from between lift components. Observe all safety precautions during the preventative maintenanc...

  • Page 13

    Trouble shooting guide page 11 problem cause correction drill bit not concentric. Foreign material in chuck or in drill plug. Inspect and clean. Drill bit is bent. Replace drill bit. Drill bit not seated in chuck properly. Reinsert drill bit correctly. Chuck is not tight to spindle. Tighten set scre...

  • Page 14: See Parts List On Page 14

    Parts diagrams front, back, and side view page 12 see parts list on page 14.

  • Page 15: See Parts List On Page 14

    Parts diagrams page 13 interiror front and back see parts list on page 14.

  • Page 16

    Parts diagrams page 14 parts list ez-108a: handle assembly fm5-5006: rocker switch (on/off) ez-117a: shroud assembly fm5-5003: chuck fm5-5011: chuck release guard hollow drill bit ebm2-0111a: pressure foot assembly 3s-14: table scales ebms-114a: table assembly ez-1025: base ebm-44a: channel guard fm...