- DL manuals
- Laundrylux
- Dryer
- DAWF0 SERIES
- Operating Manual
Laundrylux DAWF0 SERIES Operating Manual
Summary of DAWF0 SERIES
Page 1
Crossover in a class by itself laundrylux 461 doughty boulevard inwood, ny 11096-0338 www.Laundrylux.Com service: (516) 371-0700 parts: (516) 271-2000 dawf0 and daws0 series dryers w d r y e r o p e r a t i n g m a n u a l x.
Page 2
2 laundrylux 112999-1 table of contents _____________________ retain this manual in a safe place for future reference please read this manual carefully to thoroughly familiarize yourself with the phase 5 coin computer system features, operational instructions, and programming characteristics. This m...
Page 3
112999-1 www.Laundrylux.Com 3 introduction __________________________ the phase 5 coin computer system is a fully programmable, highly sophisticated dryer control system. The manufacturer has designed the phase 5 coin microprocessor controller (computer) to be the most versatile and reliable coin-op...
Page 4
4 laundrylux 112999-1 anti-wrinkle this program selection helps keep permanent press items wrinkle free when they are not removed from the dryer promptly at the end of the drying and cooling cycles. The anti-wrinkle program settings are: 1. Guard delay time ..............1 to 9 minutes 2. Guard on t...
Page 5
112999-1 www.Laundrylux.Com 5 operating instructions _______________ note: unless otherwise specified at the time of ordering, the phase 5 coin microprocessor controller (computer) has been preprogrammed by the factory with the parameters shown on page 36. Should program changes be found necessary, ...
Page 6
6 laundrylux 112999-1 program selection ____________________ note: programs are stored in the phase 5 coin microprocessor controller (computer) memory and are cataloged as pl. Temperature display mode by closing the ps located on the back side of the phase 5 coin microprocessor controller (computer)...
Page 7
112999-1 www.Laundrylux.Com 7 timed mode (tine) when this parameter is selected (“tine”) and the phase 5 coin microprocessor controller (computer) has been activated, the dryer will continue to run until the preset time, including the cool down period (pl04, pl06, or pl08), has elapsed, at which tim...
Page 8
8 laundrylux 112999-1 formula: (lcde/atst) (tfas) = vended time for “ lcde” (25¢/50¢) (30) = 15 minutes settings: pl09 (lcde) ...................... 25 pl11 (tfas) ........................ 30 pl12 (atst) ........................ 50 (dual coin) in the accumulative time (atin) mode, when using a dual ...
Page 9
112999-1 www.Laundrylux.Com 9 rotational safe guard – optional (nsen) this program monitors the rotation of the tumbler and works in conjunction with a special sensor (optional) located at the rear tumbler support area of the dryer . If the tumbler is not rotating (i.E., broken belt, failed motor , ...
Page 10
10 laundrylux 112999-1 pl12 – amount to start (atst) this program sets the “amount to start” the dryer and can be programmed from a minimum of 1 to a maximum of 9999. Pl13 – minimum amount for additional time (afat) this program need only be set when the phase 5 microprocessor controller (computer) ...
Page 11
112999-1 www.Laundrylux.Com 11 ➞ notes _______________________________________________________ ____________________________________________________________ ____________________________________________________________ ____________________________________________________________ ______________________...
Page 12
12 dryer off (power on) display reads to enter temperature display display reads to enter program locations press the “perm press” keypad selection button. Display reads to advance to next program location press the “hi temp” selection button. Display reads to accelerate advance, press and hold in “...
Page 13
13 to accelerate press and hold in “lo temp” selection button. Display reads program locations and will advance downward until “lo temp” selection button is released. To enter a specific program location (i.E. Pl01) push the “perm press” selection button. Display will read specific program location ...
Page 14
14 programming ______________________________________________________________________ temperature display mode and/or (amount to start) (dryer temperature display) (temperature selection/time) cycle in progress (dryer temperature display) fill 25 (close program switch) 75f hi°2°0 13°5°f 135f (close ...
Page 15
15 left coin count (no cycle in progress) and/or (amount to start) (dryer temperature display) press “hi temp” key. Display will read “lcc” (left coin count). Press “perm press” key to display coin count. Display will read actual coin count. I.E. 0126 = 126 units or coins. To retain or save existing...
Page 16
16 right coin count (no cycle in progress) and/or (amount to start) (dryer temperature display) press “hi temp” key. Display will read “lcc” (left coin count). Press “hi temp” key. Display will read “rcc” (right coin count). Press “perm press” key to display coin count. Display will read actual coin...
Page 17
17 hi temp °far lo temp °far °cel lo temp auto tine °cel perm press hi temp auto tine hi temp lo temp lo temp hi temp perm press perm press 70f fill 25 continue pl01 (close program switch) program location 01 (pl01) (no cycle in progress) and/or (amount to start) to enter program mode, close program...
Page 18
18 display will read anti-wrinkle (guard) program status. If no change, press “perm press” key, otherwise press “hi” or “lo” key and then “perm press” key. If guard (grd) was selected, display will read tone/buzzer status. If no change, press “perm press” key, otherwise press “hi” or “lo” key and th...
Page 19
19 hi temp atst lo temp atst fill lo temp bclo bcrs fill perm press hi temp bclo bcrs hi temp lo temp lo temp hi temp perm press continue perm press nfls nfls fls fls hi temp lo temp hi temp lo temp continue or display will read l.E.D. Display status. Either no flash (nfls) or flash (fls). If no cha...
Page 20
20 hi temp sen lo temp sen nsen lo temp pl02 nsen perm press hi temp continue perm press atin atin acon acon hi temp lo temp hi temp lo temp proceed to next location to be changed to exit program mode open program switch or or or or display will read coin/time accumulation status. I.E. “atin” accumu...
Page 21
21 program location 02 (pl02) percent dry from 90 to 100% dryness level increase dryness level decrease summary: the percentage of dryness is programmable from a minimum of 90% to a maximum of 100%. Or pl02 pdry pl03 perm press 100 hi temp perm press to exit program mode open program switch lo temp ...
Page 22
22 program location 03 (pl03) hi temp location to be viewed/changed. Press “perm press” key. Display will read “hi°f,” “hi temp” key status for 3-seconds and then the actual temperature programmed. If no changes, press “perm press” key otherwise press “hi” or “lo” key and then “perm press” key. Temp...
Page 23
23 program location 04 (pl04) hi temp cool down temperature/time location to be viewed/changed. Press “perm press” key. Display will read “hicd,” hi temp cool down status for 3-seconds and then the actual temp and time programmed. If no change press “perm press” key twice, otherwise press “hi” or “l...
Page 24
24 summary: lo temp is programmable from a minimum of 100 ° f to a maximum of 190 ° f in ten-degree increment s or from a minimum of 38° c to a maximum of 88° c in five-degree increments. Program location 05 (pl05) lo temp location to be viewed/changed. Press “perm press” key. Display will read “lo°...
Page 25
25 program location 06 (pl06) lo temp cool down temperature/time pl06 locd perm press · 100 · 2 hi temp perm press lo temp refer to programming instructions for instructions on entering program locations. (wait 3-seconds) 100 · 2 lo temp hi temp perm press pl07 proceed to next location to be changed...
Page 26
26 program location 07 (pl07) perm press temp location to be viewed/changed. Press “perm press” key. Display will read “pp°f,” “perm press” temperature key status for 3-seconds and then actual temperature programmed. If no change, press “perm press” key otherwise press “hi” or “lo” key and then “per...
Page 27
27 program location 08 (pl08) perm press cool down temperature/time location to be viewed/changed. Press “perm press” key. Display will read “ppcd,” “perm press” key cool down status for 3-seconds and then cool down temperature and time programmed. If no changes, press “perm press” key twice. Otherw...
Page 28
28 program location 09 (pl09) left coin denomination location to be viewed/changed. Press “perm press” key. Display will read “lcde,” left coin denomination for 3-seconds and the left coin acceptor denomination programmed (i.E. 25¢). If no change, press “perm press” key, otherwise press “hi” or “lo”...
Page 29
29 program location 10 (pl10) right coin denomination location to be viewed/changed. Press “perm press” key. Display will read “rcde,” right coin denomination for 3-seconds and the right coin acceptor denomination programmed (i.E. 25¢). If no change, press “perm press” key, otherwise press “hi” or “...
Page 30
30 program location 11 (pl11) time for amount to start location to be viewed/changed. Press “perm press” key. Upper display will read “tfas” (time for amount to start) and the lower display will read the actual amount programmed. If no change, press the “perm press” key, otherwise press the “hi temp...
Page 31
31 program location 12 (pl12) amount to start location to be viewed/changed. Press “perm press” key. Display will read “atst,” amount to start for 3-seconds and then time programmed. If no change, press “perm press” key, otherwise press “hi” or “lo” key and then “perm press” key. Summary: the amount...
Page 32
32 location to be viewed/changed. Press “perm press” key. Display will read “afat,” amount for additional time (acon mode only) for 3-seconds and then amount programmed. If no change, press “perm press” key, otherwise press “hi” or “lo” key and then “perm press” key. Program location 13 (pl13) coin ...
Page 33
33 program location 14 (pl14) maximum time for auto dry location to be viewed/changed. Press “perm press” key. Display will read “adrt,” automatic maximum drying time for 3-seconds and then time programmed. If no change, press “perm press” key, otherwise press “hi” or “lo” key and then “perm press” ...
Page 34
34 location to be viewed/changed. Press “perm press” key. Display will read “gdly,” guard delay time for 3-seconds and then time programmed. If no change, press “perm press” key, otherwise press “hi” or “lo” key and then “perm press” key. Program location 15 (pl15) anti-wrinkle timing summary: guard...
Page 35
35 pl16 agt perm press 10 hi temp perm press lo temp refer to programming instructions for instructions on entering program locations. (wait 3-seconds) a 6 ("hold in" to accelerate) ("hold in" to accelerate) lo temp perm press b 65 proceed to next location to be changed to exit program mode, open pr...
Page 36
36 laundrylux 112999-1 factory preset programs/parameters unless otherwise specified at the time of ordering, the phase 5 microprocessor controller (computer) has been preprogrammed by the factory with the following programs/ parameters. Should changes be found necessary, please read this phase 5 co...
Page 37
112999-1 www.Laundrylux.Com 37 there are three l.E.D. Indicators ( “red” lights) located at the lower back side area of the microprocessor controller (computer) which are identified/labeled as “door,” “heat,” and “mtr” (motor). These l.E.D.S indicate that the output s of the microprocessor controlle...
Page 38
Part no. 112999 1 - xx/xx/12.