1. DL manuals
  2. Lazerlogic
  3. Barcode Reader
  4. LL2424
  5. Programme Manual

Lazerlogic LL2424 Programme Manual

Summary of LL2424

  • Page 1

    01256 840927 sales@lazerlogic.Com kensington house, 21 mill road, basingstoke, hampshire rg24 9sn @ innovation by design lazerlogic ll2424 programme manual.

  • Page 2

    2 enter/exit programming mode (☆represents the default value).

  • Page 3: Contents

    3 contents contents .......................................................... 3 introduction .................................................... 4 setup steps ...................................................... 4 system setting ................................................ 5 sleep time selec...

  • Page 4: Introduction

    4 introduction this is an advanced programming guide for omnidirectional laser barcode scanner. If you want to read the detailed user’s manual, please visit the official website to download or contact your dealer for detail. Setup steps in order to change the scanner setting, please follow the steps...

  • Page 5: System Setting

    5 system setting ☆reset (return to factory default) reading of the “reset” barcode label turns all parameters back to default values, and the scanner remains in the last interface set when it is reset. Abort (exit programming mode).

  • Page 6

    6 after the replacement of different types of data lines, please do the following interface settings according to your optional data line. ☆return to pc/at default return to rs-232 default.

  • Page 7

    7 return to usb default return as customer default.

  • Page 8: Sleep Time Selection

    8 save as customer default sleep time selection in this section, user can set both laser and motor to either into sleep mode. The timeout programming labels will allow users to set the different time frame before entering into laser or motor sleep mode. The feature reduces power consumption and prol...

  • Page 9

    9 mode as motor enters sleep mode. Motor sleep mode off motor sleep time 10 minutes.

  • Page 10

    10 ☆motor sleep time 30 minutes laser sleep mode off.

  • Page 11

    11 ☆laser sleep time 10 minutes laser sleep time 30 minutes.

  • Page 12: Same Code Delay Time

    12 same code delay time in order to avoid an unwanted reading the same barcode, the time interval of the same barcode should not set too short. 50ms 200ms.

  • Page 13

    13 ☆300ms 500ms.

  • Page 14: Beeper Sound Selection

    14 infinite beeper sound selection ☆power up tone enable.

  • Page 15: Tone

    15 power up tone disable tone low.

  • Page 16

    16 ☆medium high.

  • Page 17: Duration

    17 silent duration 50ms.

  • Page 18

    18 ☆100ms 200ms.

  • Page 19: Volume

    19 volume low medium.

  • Page 20

    20 ☆high barcode identifier code setting code 39.

  • Page 21

    21 itf 2 of 5 chinese postal code.

  • Page 22

    22 upc-e upc-a.

  • Page 23

    23 ean-13 ean-8.

  • Page 24

    24 codabar code 128.

  • Page 25

    25 code 93 msi.

  • Page 26

    26 rss-14 rss-14 limited.

  • Page 27

    27 rss expanded save setting to confirm.

  • Page 28: Message Terminator

    28 message terminator rs-232 none ☆cr/lf.

  • Page 29

    29 cr tab.

  • Page 30

    30 stx/etx eot.

  • Page 31: Usb Hid & Keyboard Wedge

    31 usb hid & keyboard wedge none ☆enter.

  • Page 32: Baud Rate

    32 tab rs-232c interface configuration baud rate 1200

  • Page 33

    33 2400 4800

  • Page 34

    34 ☆9600 19200

  • Page 35

    35 38400 57600

  • Page 36: Capital Lock

    36 115200 capital lock s hift.

  • Page 37: Function Key Emulation

    37 ☆reset function key emulation enable.

  • Page 38: Data Edit

    38 ☆disable data edit prefix and suffix the prefix and suffix section allows you to append a prefix or suffix to every message. There is no restriction in selecting prefix or suffix characters as far as the sum of the lengths of prefix and suffix is not greater than 10 digits. 1. Scan the “enter/exi...

  • Page 39

    39 2. Select either prefix or suffix that you are going to program by scanning the corresponding label. If you want to add both prefix and suffix, you should operate separately; 3. Scan the characters you want to set as header or trailer from the full ascii. 4. Scan “saving setting to confirm” label...

  • Page 40

    40 suffix save setting to confirm.

  • Page 41

    41 truncate header/trailer character this setting allows you to truncate a number of header or trailer for symbology. As a result, the specific character you select is deleted from the symbology you want. 1. Scan the “enter/exit programming mode” label; 2. Select the “truncate header/ truncate trail...

  • Page 42

    42 truncate trailer save setting to confirm.

  • Page 43: Add Code Length

    43 add code length this setting is used to set whether the barcode length character can be used as header. Enable disable.

  • Page 44: Reading Code Selection

    44 reading code selection ☆code 39 enable code 39 disable.

  • Page 45

    45 codabar enable ☆codabar disable.

  • Page 46

    46 ☆upc/ean/jan enable upc/ean/jan disable (only can’t transmitted but can decode).

  • Page 47

    47 itf 2 of 5 enable ☆itf 2 of 5 disable.

  • Page 48

    48 chinese postal code enable ☆chinese postal code disable.

  • Page 49

    49 ☆code 128 enable code 128 disable.

  • Page 50

    50 code 93 enable ☆code 93 disable.

  • Page 51

    51 ean-128 enable ☆ean-128 disable.

  • Page 52

    52 ean convert to issn/isbn enable ean convert to issn/isbn disable.

  • Page 53

    53 code 32 enable ☆code 32 disable.

  • Page 54

    54 msi enable ☆msi disable.

  • Page 55

    55.