- DL manuals
- Lea
- Brush Cutter
- LE25254BP
- Instruction Manual
Lea LE25254BP Instruction Manual
Summary of LE25254BP
Page 1
Es manual de instrucciones it libretto d’istruzioni en instruction manual pt manual do operador fr manuel d’instructions brushcutter / roÇadeira / le25254bp/le25326bp desbrozador / decespugliatori / dÉbroussailleuse / le25427b / le25517b.
Page 2: Index
2 1. Introduction 4. Machine symbols 5. Machine description 7. Machine usage 9. Trouble shooting 10. Transport 12. Recycling declaration of conformity ce are sure that you will appreciate the quality of the machine and that the machine will help you to carry out its required functions for a long per...
Page 3: 2. Security Measures
3 english to avoid incorrect manipulation of this machine, read the instruction manual before using the machine for the first time. All information included in this manual is relevant and important for your security as well as for the security of other people, animals and objects surrounding you. Sh...
Page 4
4 cover the blade. An appropriate use of the machine the cutting elements. Store the machine well away from children. 2.2.1. Work clothes dress adequately. Do not wear loose clothing or jewels. Maintain your hair, clothes and gloves well away from all moving parts. Use eye and ear protection always ...
Page 5
5 english 2.4. Security when using fuel important: the fuel used is highly inflammable. If the fuel or the machine catch fire, fight the flames with a dry dust fire extinguisher. Always avoid eye contact with the fuel and the oil. If petrol or oil were to come into contact with your eyes, clean thes...
Page 6: 3. Warning Symbols
6 use of the machine. In order to ensure safe operation and maintenance of the machine are the following symbols in the machine. Air positions: this area will be of a diameter of 15 meters from the point in which you are protective steel. Sense of rotation. Never use only fuel or fuel in a bad state...
Page 7: 5. Machine Description
7 english 5.1. Conditions of usage other wooden objects or of any other material. 5.2. Detailed description of the product 1. Transmission. 2. Throttle trigger. 3. Switch starter. 4. Safety lever. 5. Handlebar. 6. Hitch of harness. 7. Air filter cover. 10. Starter handle. 11. Air clutch. 12. Protect...
Page 8
8 5.3. Technical characteristics the technical characteristics can be changed without prior warning. Description brushcutter brand lea model engine cylinder capacity 3 engine speed at idle speed -1 3.000 -1 9.000 capacity of deposit 3 cutting tool blade 254 nylon head 420 blade nylon head Ø 2,5 numb...
Page 9: 6. Start Up Instructions
9 6.1. List of materials this machine includes the following elements that you will find inside the box: 6.2. Mounting the machine 6.2.1. Installation of the handlebar handlebar mounted: handlebar turning possibility: 6.2.2. Installation of transmission 6.2.3. Installation of protector protective su...
Page 10
10 screwdriver through the transmission hole and the notch on the plate. 6.2.4. Description of the cutting attachment 1. Steel disc. 2. 2 wire head. 3. Sheet with notch for coupling the head or disc. 4. Sheet. 5. Protective bell of the disc. 6. Protective hood of the disc. 7. Disc nut. 8. Saucer. 6....
Page 11
11 6.2.7. Harness installation 6.3. Check points before starting do not use this machine if it becomes damaged or wrongly regulated. Use this machine for the purpose for which it was designed. Any other use may be dangerous for the user to the machine and for people, animals and things you may have ...
Page 12
12 6.3.1. Gasoline and oil mix attention: motor fuel is highly flammable. If the fuel or the machine burns, put the fire off with a fire dust extinguisher. Use unleaded fuel of 95 ° and 100% synthetic oil for do not use fuel with ethanol or methanol because will damage the engine. Motor fuel: mix ga...
Page 13: 7. Machine Usage
13 allow the engine to warm up for approximately one 6.4.1. Starting the machine from hot position. 3. Pull the start rope until the machine starts. If the machine does not start after pulling at the rope a few times, please refer to the cold start up section. 6.4.2. Engine stoppage at idle speed fo...
Page 14
14 if you slip or fall stop accelerating and move the clean the work area and eliminate any obstacles that could cause accidents. And remove any objects that could cause the nylon head of the machine to get tangled on. Also remove any parts that the disc could violently hit causing these to move in ...
Page 15: 8. Maintenance and Service
15 not operate the brush cutter in areas with metallic materials. Always use the proper protective equipment. Don’t use this machine in areas where you can’t see properly. 7.2. Cut with the disc and there are no signs of damage or abrasion. Installed in accordance with the instructions and that the ...
Page 16
16 fuel filter end of the suction pipe and can be removed with and cause malfunctions or stop it. With gasoline. Check the spark the most common problems when starting a machine.
Page 17: 9. Trouble Shooting
17 on the symptoms, we provide you with a series of probable causes and the solutions: the compression of the cylinder is normal the spark is fine probable cause corrective action fuel filter is dirty the switch is “off’” properly connected the piston and the rings are worn the cylinder is scratched...
Page 18
18 sympton the machine oscilates the engine overheats the engine does not go round the engine stops or can not stand idle probable cause corrective cause piston used uninterrumped overuse dirty exhaust pipe not correct fuel carburetor dirty air filter dirty fuel filter carburetor incorrectly adjuste...
Page 19: 10. Transport
19 if you are going to transport the machine in a vehicle, machine from sliding or falling over from side to side. It is always neccesary to turn off the motor before transport the machine. Always carry the machine with the motor off, with the machine hanging from the harness and use the blade does ...
Page 20: 13. Warranty
20 13.1. Warranty period - according to the following described terms the purchase date, and it will cover faulty pieces owing to an incorrect manufacture. 13.2. Exclusions the warranty does not cover: - pieces worn out due to wear and tear. - failures that turn out because of an incorrect use of th...
Page 21: Declaration of Conformity Ce
21 hand-held unit fitted with a rotating blade made of metal or plastic intended to cut weeds, brush, small trees and similar vegetation.”, comply with all the requirements stated by the directive 2006/42/ec of the european parliament and of the council of 17 may 2006 on machinery. These tools also ...