Brushcutter decespugliatrice le25326d le25427d le25517d original instructions istruzioni originali.
Index (gb) indice (it) detailed description of the product……………………………………… 1 technical characteristics……………………………………………………... 1 description of symbols………………………………………………………….. 2 safety instructions……………………………………………………………….. 3 special satety warning………………………………………………………….. 4 assembly…………………………………………………...
1 detailed description of the product 1. Transmission. 2. Throttle trigger. 3. Switch on/off. 4. Safety lever. 5. Ratchet. 6. Starter handle. 7. Choke. 8. Primer. 9. Handlebar. 10. Air filter cover. 11. Fuel cap. 12. Fuel tank. 13. Guard support. 14. Protector. 15. Nylon head. 16. Nylon cutting blad...
2 description of symbols symbols are used in this manual to attract your attention to possible risks. The safety symbols and the explications which accompany them must be perfectly understood. The warning themselves do not prevent the risks and can not be a substitute for proper methods of avoiding ...
3 wear robust footwear when using the device. Wear protective gloves when using the device. 40:1 the part to refuel the “mix gasoline” on fuel tank. Safety instructions this appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or la...
4 - walk, never run. - exercise extreme caution when changing direction on slopes. - do not cutting excessively steep slopes. - use extreme caution when reversing or pulling the appliance towards you. - never operate the appliance with defective guards or shields, or without safety devices. - switch...
5 7. Never touch the spark plug or plug cord while the engine is in operation .Doing so may result in being subjected to an electrical shock . 8. Never touch the muffler, spark plug or other metallic parts of the engine while the engine is in operation or immediately after shutting down the engine. ...
6 3.2 fit the nylon cutting head. Remove another shield after release the nuts as picture showing. Still hold the flange, take the nylon cutting head on the shaft and rotate counter-clockwise, the nylon cutting head is fitted. 3.3 release the nylon cutting head. Use screw driver to hold flange and t...
7 4.2 release blade . Use screw driver to hold flange and release nut, the blade can be took off. Warning! Please make sure the cutting head has been assembled correctly before use! Note : the packaging material is made of recycle materials. Dispose of packaging materials in accordance with regulati...
8 never use oil for 4-cycle engine use or water cooled 2-cycle engine. If can cause spark plug fouling exhaust port blocking or piston ring sticking. Mixed fuels, which have been left unused for a period of one month or more may clog the carburetor or result in the engine failing to operate properly...
9 check the safe condition of the device: - check the device for leaks. - check the device for visual defects. - check that all parts of the device have been securely fitted. - check that all safety devices are in proper condition. Once the machine has been set up properly, start the engine as follo...
10 4. Pull the recoil starter handle 3-5times to start the engine, as following picture. 5. Adjust the choke leverl to b(half open) position. 6. Pull the rope until engine starts 7. When the engine is running and idling. The throttle lever on handle is as below picture. First press the lock off leve...
11 8. If use nylon cutter, before cutting, need bump to feed line on hardness area 9. If meet any problems, press the engine switch "O" , the machine will stop running. If need stop cutting head working, release the throttle lever. 10. If meet any problem, pull the pin of safety belt, then release t...
12 maintenance schedule 12 hours of use 24hours of use 36hours of use air filter clean clean replace spark plug check clean replace expert inspection is required: a) if the brush cutter strikes an object. B) if the motor stops suddenly c) if the blade is bent (do not align!) d) if the gears are dama...
13 down beforehand. Troubleshooting before performing any maintenance or cleaning work, always turn off the engine and wait until the cutter has come to a standstill 1) engine does not run: ---reassemble the blade or nylon cutter. ---check the fuel weather use out or not. 2) engine power drops: ---h...
14 ……………………………………………………………………………………………………………. Conformity declaration the undersigned, hereby certifies that the units described below : brushcutter model le25326d ( pnbc305b-3b ) le25427d ( pnbc415b-3b ) le25517d ( pnbc520b-3 ) power 1,05 1,25 1,45 brand: lea measured sound power level: 96 db (a) gu...
15 descrizione del prodotto 1. Transmissione. 2. Grilletto dell’acceleratore 3. Interuttore on / off. 4. Leva di sicurezza. 5. Bottone blocca acceleratore 6. Maniglia di avviamento. 7. Soffocano dell’aria. 8. Primer. 9. Manubrio. 10. Tappo del filtro dell’aria. 11. Tappo del serbatoio carburante. 12...
16 descrizione dei simboli questo manuale utilizza una serie di simboli per avvertirvi dei possibili rischi. È necessaria un’adeguata comprensione dei simboli di sicurezza e delle spiegazioni correlate. Le stesse avvertenze non prevengono i rischi e non possono sostituire le corrette misure da prend...
17 indossare scarpe solide durante l’uso della macchina. Indossare guanti protettivi durante l’uso della macchina. 40:1 simbolo per il rifornimento con “miscela di benzina” sul serbatoio. Istruzioni di sicurezza questo dispositivo non può essere usato da persone (inclusi i bambini) con ridotte capac...
18 - evitare l’uso sull’erba bagnata, se possibile. - assicurarsi sempre di avere i piedi ben saldi nel caso di pendenze. - camminare, non correre mai. - fare molta attenzione durante i cambi di direzione effettuati in pendenza. - non usare su pendenze estremamente ripide. - fare molta attenzione du...
19 4. Assicurarsi sempre di spegnere il motore se l’erba s’incastra nella lama durante l’uso o se è necessario controllare la macchina o fare rifornimento. 5. Se la lama urta un oggetto, per esempio una pietra, spegnere immediatamente il motore e controllare lo stato della lama, sostituendola se è d...
20 3. Montaggio della testina. 3.1 allentare il bullone. Allineare i due fori della flangia e della protezione, usare una chiave a brugola per tenere ferma la flange, come illustrato nell’immagine sottostante e girare in senso orario la chiave a tubo, rilasciando il bullone. 3.2 montaggio della test...
21 3.3 rimozione della testina in nylon. Utilizzare il cacciavite per tenere la flangia e girare la testina in nylon in senso orario. In questo modo potrà essere rimossa. 4.1 regolare la lama. Tenere la flangia con la chiave esagonale, poi allentare i dadi come nell’immagine sottostante, poi posizio...
22 non utilizzare mai olio per motori a 4 tempi o a 2 tempi con raffreddamento ad acqua. Può causare la formazione d’incrostazioni nel foro di scarico della candela o l’incollaggio delle fasce elastiche. Le miscele non utilizzate per un mese o più possono ostruire il carburatore o causare guasti nel...
23 scarico carburante - tenere un contenitore sotto il bullone di scarico. - svitare e rimuovere il coperchio del serbatoio. - lasciare che il carburante fuoriesca completamente. - avvitare bene manualmente il coperchio del serbatoio. Avviamento non accendere la macchina prima di completare il monta...
24 3. Mettere la leva d’aria nella posizione a (off) 4. Tirare la cordicella dell’avviamento a strappo 3-5 volte per accendere il motore, come nell’immagine sottostante. 5. Regolare la leva’aria nella posizione to b (aperta a metà) . 6. Tirare la cordicella finchè il motore si accende.
25 7. Quando il motore è in funzione a vuoto la leva dell’acceleratore posizionata sulla maniglia dev’essere come nell’immagine sottostante. Premere il pulsante blocca acceleratore e poi la leva dell’acceleratore e la macchina entrerà in funzione. 8. Se si usa la testina in nylon, dura per far avanz...
26 10. Se si riscontra qualche problema, sganciare il moschettone e staccare immediatamente il decespugliatore. 11. Se la macchina è calda, la leva dell’acceleratore può essere regolata nella posizione on all’avviamento della macchina. Manutenzione spegnare sempre il motore prima di effettuare inter...
27 pulizia filtro dell’aria staccare il filtro dell’aria e l’elemente filtrante in spugna. Per evitare la caduta di oggetti dentro il serbatoio dell’aria, rimettere il coperchio. Lavare l’elemento filtrante con acqua calda e sapone, risciacquare e lasciare che si asciughi in modo naturale. Avvertenz...
28 …………………………………………………………………………………………………………… dichiarazione ce di conformitÀ il sottoscritto certifica che i dispositivi descritti di seguito decespugliatrice modello le25326d ( pnbc305b-3b ) le25427d ( pnbc415b-3b ) le25517d ( pnbc520b-3 ) potenza 1,05 1,25 1,45 marca: lea livello di potenza acustic...
9 www.Dunsch.Com.