- DL manuals
- Lectronics
- Processor
- DM1612F
- Hardware And Software Installation Manual
Lectronics DM1612F Hardware And Software Installation Manual
Summary of DM1612F
Page 1
Dm series digital audio processors models: dm1624f dm1612f dm812 hardware and software installation guide rio rancho, nm, usa www.Lectrosonics.Com fill in for your records: serial number: purchase date:.
Page 2
Dm series installation guide lectrosonics, inc. 2.
Page 3
Dm series installation guide rio rancho, nm 3 important safety instructions this symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure -- voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you...
Page 4
Dm series installation guide lectrosonics, inc. 4 table of contents introduction .............................................................................................................................................. 5 unpacking the unit ..........................................................
Page 5
Dm series installation guide rio rancho, nm 5 introduction the purpose of this guide is to assist in the setup and operation of a typical dm system. This guide assumes familiarity with the dm series digital audio processors, its components and software menus and setup screens. To get the most out of...
Page 6
Dm series installation guide lectrosonics, inc. 6 installing the dm system into a rack the dm1624f and dm1612f occupy two rack spaces. The dm812 occupies a single space. Mount with 4 rack screws using the appropriate mounting holes. It is rec- ommended to use nylon washers to prevent damage to the f...
Page 7
Dm series installation guide rio rancho, nm 7 since the calculated vph is equal to vph from the microphone specification sheet, this is a marginal situ- ation. Microphone number 2: from specification sheet: v ph (min) = 9 v i mic (max.) = 2 ma v ph = 15 v - (1k)(.002a) v ph = 15 v - 2v = 13 v since ...
Page 8
Dm series installation guide lectrosonics, inc. 8 programmable inputs programmable inputs are provided to enable external control over a variety of parameters. Each input can respond to either a contact closure or a continuous voltage. The following illustrates common connections to the programmable...
Page 9
Dm series installation guide rio rancho, nm 9 figuring a unit as a master or a slave can be done using the front panel lcd and controls or the control panel gui interface. Note: in order to use the convenient control panel gui, lecnet2™ must be installed on the attached computer system. (see install...
Page 10
Dm series installation guide lectrosonics, inc. 10 expansion port digital audio network interface interconnection diagram programmable inputs/ outputs 1 - gnd 2 - in 12 3 - in 14 4 - in 16 5 - in 18 6 - in 20 7 - in 22 8 - gnd 9 - out 9 10 - out 11 11- out 13 12 - out 15 13 - gnd 14 - +5v 15 - in 13...
Page 11
Dm series installation guide rio rancho, nm 11 installing lecnet2 ™ software and usb driver lecnet2™ is a graphic user interface (gui) designed to allow easy setup and monitoring of dm compo- nents using windows ® 2000 or xp computer systems. Lecnet2™ includes the necessary control panels to configu...
Page 12
Dm series installation guide lectrosonics, inc. 12 5. When the driver installation is complete, the final page of the wizard appears. Click finish to com- plete the lecnet2™ usb driver installation. Installation additional units (or lecnet 2 ™ devices) the windows xp operating system regards all lec...
Page 13
Dm series installation guide rio rancho, nm 13 usb driver installation (windows 2000) first time installation when a lecnet2™ device is connected to a comptuer system running the windows ® 2000 operating system for the very first time, the windows found new hard- ware wizard automatically opens. Use...
Page 14
Dm series installation guide lectrosonics, inc. 14 initial setup the initial setup of a dm system is a relatively simple three step process: connect the unit to the computer, turn on the computer and select the appropriate control panel, preset the input, matrix and output. This process assumes that...
Page 15
Dm series installation guide rio rancho, nm 15 inputs matrix outputs the dm can be configured in the installation or a configuration file can be created off line in advance. The minimum required setup to pass audio includes: inputs, matrix and outputs. Input and output filters, compressors and delay...
Page 16: Limited One Year Warranty
31 aug 2009 581 laser road ne • rio rancho, nm 87124 usa • www.Lectrosonics.Com (505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.Com limited one year warranty the equipment is warranted for one year from date of purchase against defects in materials or workmanship provided i...