- DL manuals
- Lectrosonics
- Receiver
- M2R
- Instruction Manual
Lectrosonics M2R Instruction Manual
Summary of M2R
Page 1
Digital iem system instruction manual rio rancho, nm, usa www.Lectrosonics.Com fill in for your records: serial number: purchase date:.
Page 2
Duet lectrosonics, inc. 2 system setup procedures summary of steps 1) install receiver batteries and connect power to transmitter. 2) power receiver on with on/off and volume knob. 3) scan for an available frequency on the receiver. 4) power on the transmitter and sync with receiver. 5) enable rf in...
Page 3
Digital iem system rio rancho, nm 3 table of contents system setup procedures .....................................................................................................................................................................2 summary of steps .........................................
Page 4
Duet lectrosonics, inc. 4 duet system overview the m2 duet digital iem system is designed and developed with the professional touring, installation, theater and broadcast customers in mind. Convention- al in-ear wireless monitor systems rely on decades-old technology: fm transmission with multiplexe...
Page 5
Digital iem system rio rancho, nm 5 flexlist™ additionally, the m2r includes a flexlist™ mode, where up to 16 mixes can be accessed by name. This feature enables a monitor engineer to quickly find and listen to any of the performer’s mixes on the stage. A flexlist mix is a profile of a performer’s p...
Page 6
Duet lectrosonics, inc. 6 m2r receiver operation usb port battery compartment door belt clip mounting sockets headphone output ir (infrared) port on/off and volume knob rf link led battery status led.
Page 7
Digital iem system rio rancho, nm 7 battery status led when the battery status led on the keypad glows green the batteries are good. The color changes to red at a midpoint during the runtime. When the led begins to blink red, only a few minutes remain. The exact point at which the led turns red will...
Page 8
Duet lectrosonics, inc. 8 installing batteries power is provided by two aa batteries. The batteries are connected in series by a plate in the battery door. Slide the battery door outward to open it polarity is marked on the rear panel. Polarity markings lcd main window battery life indicator receive...
Page 9
Digital iem system rio rancho, nm 9 navigating the menus from the main window, press menu/sel to enter the menu, then navigate with the up and down arrows to highlight the desired setup item. Press menu/sel to enter the setup screen for that item. Refer to the menu map on the following page. Press m...
Page 10
Duet lectrosonics, inc. 10 m2r lcd menu map the menus presented on the lcd are arranged in a straightforward manner, with those that are likely to be used more often located at the top of the tree. Scan flexlist frequency sel back sel back frequency 548.900 900 sel back vol/bal sel back mixer sel ba...
Page 11
Digital iem system rio rancho, nm 11 menu item descriptions scan use the scan function to identify a usable frequency. The area in red has not been scanned. Allow the scan to continue until the entire band has been scanned. Once a full cycle has been completed, press menu/ select again to pause the ...
Page 12
Duet lectrosonics, inc. 12 flex list flexlist allows the user to set up a list of profiles, by name, to quickly and easily listen to any of the mixes on site individually. Listen - choose a mix from the list and hear what is transmitting add - add a mix to the available flex list (action performed v...
Page 13
Digital iem system rio rancho, nm 13 limiter limiter function allows the user to set volume and dynamic range for headphone use. Gain - the default setting (0) is linear, but if additonal volume is needed, use the up and down arrows to adjust the audio by up to +18 db in 3db steps. Warning: increasi...
Page 14
Duet lectrosonics, inc. 14 lock/unlock the front panel controls can be locked to prevent un- wanted changes. About m2r displays general information about the m2r, including serial number and the versions for both fpga and main firmware running in the receiver. Default returns all settings to the fac...
Page 15
Digital iem system rio rancho, nm 15 m2r accessories 26895 wire belt clip. 21926 usb cable for firmware updates.
Page 16
Duet lectrosonics, inc. 16 m2t transmitter operation usb port antenna jack power inlet menu navigation buttons power switch return to previous screen ir port headphone volume adjustment dante ports ethernet port antenna jack headphone jack reset button m2t front panel m2t back panel menu/select chan...
Page 17
Digital iem system rio rancho, nm 17 operating instructions ir (infrared) port settings, including frequency, name, limiter, mix mode, etc. Can be transferred to and from the m2t transmitter via this port to an ir enabled receiver to simplify setup. Usb port for firmware updates and connection to wi...
Page 18
Duet lectrosonics, inc. 18 m2t lcd menu map rf enable/level rf tuning sync scan sel back sel back sel back sync settings sel back sync flexlist sel back audio level/trim sel back sel back audio input type sel back sel back sel back sel back headphone monitor front panel setup network settings edit n...
Page 19
Digital iem system rio rancho, nm 19 menu item descriptions rf enable/level allows rf transmission to be turned on and off and set rf levels at 10, 25 or 50 mw. Rf tuning allows manual selection of the operating frequency. Sync scan receive frequency scan via ir port or tune transmit- ters manually....
Page 20
Duet lectrosonics, inc. 20 audio input type set independent channels to analog or digital (dante). Note: when selecting a dante input, user must be familiar with the dante controller from audinate. Audio polarity select normal or inverted polarity for each audio channel. Headphone monitor the headph...
Page 21
Digital iem system rio rancho, nm 21 (2) a500ra20 antenna hardware installation unpacking the unit compare the packing list enclosed with the m2t with the original order. Inspect all items for damage. Im- mediately call 1-800-821-1121 to report any items that are missing or damaged. The sooner we ge...
Page 22
Duet lectrosonics, inc. 22 installing two m2ts into a single rack space the m2t transmitter occupies a half rack space, and comes with hardware to mount two (2) m2t receivers into a rack. 1. Remove the trim cap (part #p1330) from both sides of the front panel of the first m2t unit to be rack mounted...
Page 23
Digital iem system rio rancho, nm 23 6. Install the front tie bracket (part #25991) into the open inboard slot in the side of the chassis cover panel with the protruding nuts facing rearward, af- fix with two (2) cap screws (part #28885) provided and firmly tighten with the hex wrench. (see front vi...
Page 24
Duet lectrosonics, inc. 24 m2t accessories dcr15/a4u front mount antenna kit fmakm2t 27080 dante port cover (included with non-dante model) dante 4x4-tm dante card kit (included in dante model) rmpm2t-1 rack kit for mounting one m2t into a single rack space sna600a antenna sna600a accessories: arg 1...
Page 25
Digital iem system rio rancho, nm 25 specifications m2r receiver operating spectrum: 470.100 - 614.375 mhz modulation type: 8psk with forward error correctionoccupied latency: digital source: 1.0 ms over dante network analog source: audio performance: frequency response: 20hz - 15 khz, - 3db thd+n: ...
Page 26
Duet lectrosonics, inc. 26 wireless designer software and usb driver windows installation download the wireless designer software installer from the web sites under the support tab at: http://www.Lectrosonics.Com/us http://www.Lectrosonics.Com/europe/ or use the flash drive supplied with the receive...
Page 27
Digital iem system rio rancho, nm 27 wireless designer software and usb driver software for mac ® os x operating systems installation using only the firefox web browser, open wireless designer. If the firefox silverlight plugin has not been used before you will be prompted to “activate silver- light...
Page 28
Duet lectrosonics, inc. 28 isedc notices: per rss-210 this device operates on a no-protection no-interference basis. Should the user seek to obtain protection from other radio services operating in the same tv bands, a radio licence is required. Please consult industry canada’s document cpc-2-1-28, ...
Page 29
Digital iem system rio rancho, nm 29 service and repair if your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equip- ment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the inter- connecting cable...
Page 30
Duet lectrosonics, inc. 30
Page 31
Digital iem system rio rancho, nm 31.
Page 32: Limited One Year Warranty
Duet lectrosonics, inc. 32 15 december 2017 limited one year warranty the equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged...