Ledj LEDJ255 User Manual - page 5

 LEDJ Intense 19T3 RGB LED Slim Panel 

                                                    Operations

DMX mode:

To access the DMX mode, press the 

“MODE” button on the LED display to show “d001” on the 

LED display. Now press the 

“ENTER” button and use the “UP” and “DOWN” buttons to set the 

desired DMX address setting from 

“d001 - d512”.Once you have selected the desired DMX 

address setting, press the 

“ENTER” button to choose one of the 3, 6, 9 or 11 DMX channel modes 

use the 

“UP” and “DOWN” buttons and press the “ENTER” button to confirm the setting.

Static colour mode

To access the static colour mode, press the 

“MODE” button on the LED display to show “Colt” on 

the LED display. To change the brightness of each colour please see below.

Red Adjustment

To adjust the brightness of the red LEDs, press the 

“MODE” button to show “t255” on the 

display. Now press use the

 “UP” and “DOWN” buttons to adjust the brightness from 000-255.

To confirm your choice, press the 

“ENTER” button.  Note: 000 = off, 255 = full on.

Green Adjustment

To adjust the brightness of the green LEDs, press the 

“MODE” button to show “G255” on the 

display. Now press use the

 “UP” and “DOWN” buttons to adjust the brightness from 000-255.

To confirm your choice, press the 

“ENTER” button. Note: 000 = off, 255 = full on.

Blue Adjustment

To adjust the brightness of the blue LEDs, press the 

“MODE” button to show “B255” on the 

display. Now press use the

 “UP” and “DOWN” buttons to adjust the brightness from 000-255.

To confirm your choice, press the 

“ENTER” button. Note: 000 = off, 255 = full on.

Built-in programme mode

To access the static colour mode, press the 

“MODE” button on the LED display to show “Pr01” 

on the LED display. Now use the 

“UP” and “DOWN” buttons to scroll the built in programmes 

from Pr01 to Pr12.

To change the speed of the selected programme, press the 

“ENTER” button and use the “UP” 

and 

“DOWN” buttons to set the speed from 00 to 99. To add strobe press the “ENTER” button 

again and use the 

“UP” and “DOWN” buttons to set strobe from 00 to 99. To confirm your setting 

press the 

“ENTER” button. Note: 00 = slow, 99 = fast.

In 

“Pr01” you can set a specific static colour. When in Pr01, press the “ENTER” button and use 

the 

“UP” and “DOWN” buttons to scroll through the list of built-in static colours.

0 = White 

1 = Red 

2 = Amber  3 = Spring yellow  4 = Green  5 = Cyan

6 = Blue 

7 = Purple  8 = Pink 

9 = Yellow  Off = Blackout

To add strobe press the 

“ENTER” button again and use the “UP” and “DOWN” buttons to set 

strobe from 00 to 99. To confirm your setting press the 

“ENTER” button. 

Note: 00 = slow, 99 = fast.

Auto run mode

To access the auto run mode, press the 

“MODE” button on the LED display to show “AUTO” on 

the LED display. To change the speed of the auto run, press the 

“ENTER” button and use the 

“UP” and “DOWN” buttons to set the speed from 00 to 99. To add strobe press the “ENTER” 

button again and use the 

“UP” and “DOWN” buttons to set strobe from 00 to 99. To confirm your 

setting press the 

“ENTER” button. Note: 00 = slow, 99 = fast.