Leetek LTK-P1200 User Manual

Page of 8

Download

Print this page

Bookmark us

FM transmitter & Coaster Pager User’s manual

Thank you for purchasing the“ LTK-P1200 transmitter & Guest paging system”.

We are confident our cutting edge products and first rate service will satisfy your needs for years

to come. Please read this these instructions carefully before setting up your Guest Paging system!

EQUIPMENT SETUP

Keypad Sending Unit:

Unwrap all sending unit components. Lock the antenna into the hole in the upper right hand

Corner of the sending unit. Plug the power supply with the large tip into a standard 110 outlet

and plug it into the back of the sending unit. We recommend some type of surge suppressor on

the power supply for protection. Power surges are not covered under system warranty!

Coaster Steup:

Locate the black charging base in a sturdy, out of the way location. Connect the charger bases

together using the included jumper wires. Use the power- suppy with the small tip and plug it

into a standard 100 outlet and into either open plug on the charger base. Be sure to plug the

jumpers & power supply jacks in all the way.

Stack the coasters on the black charging base. The coaster number will always face front and

the red charge indicator light will be on the left.

We recommend that you do not stack coasters more than 15 high.

You should see a red light appear on each coaster. This light indicates proper charging is

taking place.

Coaster Numbers:

On the front of each coaster is your coaster number

*Smps adaptor (Transmitter Use: DC 12V 2.5A) , (Charger Base: DC12V 2.5A)

1 2 3 4 5 6 7 Next › »

Summary of LTK-P1200

Page 1
Fm transmitter & coaster pager user’s manual thank you for purchasing the“ ltk-p1200 transmitter & guest paging system”. We are confident our cutting edge products and first rate service will satisfy your needs for years to come. Please read this these instructions carefully before setting up your g...
Page 2
System configuration your system was set at the factory and will function as soon as it is powered up. Default setup is as follows: out of range alert is off. Coasters are set to vibration & flash when paged. Set time(12:00 am) range test is off this configuration should be satisfactory for most loc...
Page 3
System programming: to enter programming mode, press the “setup” button and enter the password “3690” followed by “enter”. If the password is accepted, the display will show “use * to scroll to menu options”. (use the “ ∗∗∗∗ / menu” key to scroll through the different menu options or press “cancel” ...
Page 4
2. Set the current time • at the “set current time” menu, set the hour then press “enter” key. • set the minutes and press “enter” key. • use the “# /select” key to select am or pm. • after the correct time is set, press the “enter” or “∗∗∗∗ / menu” key to return to the main menu or press the “cance...
Page 5
( coaster pager user’s manual ) handing out the coasters: give the guest a coaster. Note their name and coaster number on the sign out sheet(included). Tell the guest the coaster will signal when their table(or food) is ready. The default page for this system is for the coaster to flash and vibrate ...
Page 6
Auto-locate feature this feature causes all coasters (that are not on the charging stack) to signal at once. This feature is useful when you are closed and would like to locate any misplaced coasters around your restaurant. To locate all coasters, press “1249 – send”. Any coaster not on the charging...
Page 7
Guestcall guest paging system operation 1. When a guest arrives, remove a coaster from the stack. It will alert for 10 seconds while you show them and explain what they will be looking for when they are paged. Write the coaster number next to the person's name on the wait list. 2. When their table b...
Page 8
Leetek warrants this product against any defects that are due to faulty material or workmanship for a one-year period after the original date of consumer purchase. This warranty does not include damage to the product resulting from accident, misuse or improper electrical connection. Power supplies a...