Legacy Stoves SF250 Tribute Installation And Operator's Manual - page 12
E) Manufactured Chimney Connections - When venting
using a prefabricated chimney, be sure to contact local
building code authorities, and to follow the
manufacturer’s instructions exactly.
Your manufactured chimney may contain more parts
than is shown at right. Include all required items in
your installation. A chimney cap (A) serves to keep rain
and snow from entering the chimney. An approved
Class A chimney (B) is required for the Super Magnam
Stoker. Wall Bands (C) must be deployed for support
per manufacturer’s recommendations. A
manufacturer’s Wall Support Kit (D) will contain
required items for supporting the chimney. Such kits
will cost less than individual items purchased
separately. A Bo,om Cap (E) allows for cleaning.
e
arrow shows the location of the bo,om end cap, but it
is not visible on the drawing. A Finishing Collar (F)
provides inside wall protection. A Wall
imble (G)
provides for required clearance between the chimney
pipe passing through a e Chimney Connector (H) must be approved single wall, or a low clearance pipe, installed with required clearances in place. A Roof Brace (I) is required for chimneys that extend more than a certain distance, as referenced by the manufacturer’s instructions, from the roof. Manufactured chimneys may feature a built in “twist lock” at each joint, but a Joint Band (J) is still normally required to secure pipe at the joint. An approved Chimney Pipe Adapter (K) is required. A Ceiling Support (L) will provide structural support for the chimney and is typically part of a kit that includes items that maintain required clearances to A Storm Collar (M), and Adjustable Flashing (N) prevent water from entering the home by running down the outside of the chimney. Additional items or a kit (O) provide additional mounting support or 3re protection to the roof joists or other roof components. F) Draft Regulation - Barometric Damper Setup A stove and chimney combination that drafts well will occasionally produce more draft than is desired. Excessive draft can lead to over3ring. It will also lead to reduced eNciency, as more heat will end up going up the chimney. A barometric damper is required to limit maximum draft to -.08 column inches. e barometric damper needs to be the same diameter as the stove collar. It is to be installed in the chimney connecting pipe as shown below. U U U US SS SE E E E O O O ON N N NL LL LY Y Y Y T T T TH H H HE E E E M M M MA A A AN N N NU U U UF FF FA A A AC C C CT T T TU U U UR R R RE E E ER R R R’’’’SSSS P P P PA A A AR R R RT T T TS SS S.... D D D DO O O O N N N NO O O OT T T T U U U US SS SE E E E M M M MA A A AK K K KE E E ES SS SH H H HIIIIF FF FT T T T IIIIN N N NS SS ST T T TA A A AL LL LL LL LA A A AT T T TIIIIO O O ON N N N T T T TE E E EC C C CH H H HN N N NIIIIQ Q Q QU U U UE E E ES SS S.... A A A AL LL LL LL L P P P PR R R RE E E EF FF FA A A AB B B BR R R RIIIIC C C CA A A AT T T TE E E ED D D D C C C CH H H HIIIIM M M MN N N NE E E EY Y Y YS SS S M M M MU U U US SS ST T T T B B B BE E E E T T T TE E E ES SS ST T T TE E E ED D D D T T T TO O O O E E E EIIIIT T T TH H H HE E E ER R R R T T T TH H H HE E E E U U U U....SSSS.... O O O OR R R R C C C CA A A AN N N NA A A AD D D DIIIIA A A AN N N N H H H HIIIIG G G GH H H H T T T TE E E EM M M MP P P PE E E ER R R RA A A AT T T TU U U UR R R RE E E E S SS ST T T TA A A AN N N ND D D DA A A AR R R RD D D DS SS S,,,, U U U UL LL L 111100003333 O O O OR R R R U U U UL LL LC C C C SSSS666622229999....