1. DL manuals
  2. Legend
  3. Indoor Fireplace
  4. 738BXN (NG)
  5. Installation & Operating Instructions Manual

Legend 738BXN (NG) Installation & Operating Instructions Manual

Summary of 738BXN (NG)

  • Page 1

    L egend installation & operating instructions 4001379-06 ©2010, miles industries ltd. Gravity vent gas insert 738bxn (ng) & 738bxp (lpg) warning: if the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life....

  • Page 2: Do Not Put

    We recommend that our gas hearth products be installed and serviced by professionals who are certified in the united states by nfi (national fireplace institute ® ). Thank you ... For purchasing a valor by miles industries. Your new radiant gas heater is a technical appliance that must be installed ...

  • Page 3

    Safety and warning information...................................................................4 specifications ................................................................................................5 overview ..................................................................................

  • Page 4

    Safety and warning information children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition. Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others...

  • Page 5

    X x safety and warning information ratings model ng lpg gas natural propane altitude (ft.)* 0-4,500 feet* input maximum (btu/h) 24,000 24,000 input minimum (btu/h) 6,500 13,000 manifold pressure (in w.C.) 3.95 9.5 minimum supply pressure (in w.C.) 5.0 11.0 maximum supply pressure (in w.C.) 10.5 14.0...

  • Page 6

    Overview this appliance, as supplied, may only be installed in an existing unaltered, functioning solid-fuel burning fireplace with a working flue and constructed of non-combustible material. This appliance is approved for installation into combustible type construction only when using the 770zck ze...

  • Page 7

    28-5/8” (727 mm) 19-1/2” (495 mm) 12” (305 mm) or 12-5/8” (321 mm) varies with outer trim options 7-7/8” (200 mm) or 8-1/2” (216 mm) varies with outer trim options 20” (508 mm) gas inlet gas connection optional outer trim or surround sold separately x y dimensions cavity check that masonry step does...

  • Page 8

    9” (229 mm) a b do not put furniture or objects within 36” (914 mm) of the front of appliance combustible mantel clearances *measure taken from the underside of the mantel to finished hearth or surface that the unit is sitting on. Finishing materials combustible materials: material such as wood, com...

  • Page 9

    Approved termination required max. 36” offset at 10’-0” min. Vertical 3” liner 3” min. Bend radius m in. 10 f eet (with off set) m in. 8 f eet (without off set) minimum vent liner radius allowable vent configurations minimum vent lengths. For other allowable configurations, refer to the venting tabl...

  • Page 10

    Installation planning installer—read this first 1. You need to know from the homeowner what accessories (surround, door, etc.) will be installed with this fireplace; 2. Unpack the appliance. 3. Check that you have everything. 4. Clean cavity, chimney, ash dumps, clean-outs. 5. Install venting pipe. ...

  • Page 11

    Unpacking the appliance beware of sharp edges! Wear gloves! 1. Unpack the appliance. 2. Unpack any loose items from around the appliance and check against the pack content list provided in the documentation package. 3. Remove the window and set aside in a safe place to avoid damage. 4. Verify that y...

  • Page 12: Option 2B

    Venting installation important: this appliance’s venting system requires room air to be used in the combustion process. 1. Rough-in one 3” diameter vent liner into the existing chimney system from the roof. Be careful not to tear or damage the liner in the process. Leave plenty of liner at the botto...

  • Page 13

    Supply pressure test tapping manifold pressure test tapping supply gas the gas supply inlet connection is a 3/8” npt female connector and is located on the left hand side of the control valve. Use only new black iron or steel pipes or copper tubing if acceptable—check local codes. Note that in usa, ...

  • Page 14

    Thermostat knob gas control knob the pilot burner and electrode unit are at the left end of the burner. Push in the lighting knob and turn it counter-clockwise through the “ign” position to “pilot”. A spark should flash across from the pilot electrode to the pilot burner shield as shown below. Ignit...

  • Page 15

    Receiver gv34 valve push-on connector remote control preparation 1. Connect the wiring harness to the receiver box, by pushing the wire connector on to the receiver circuit board. The plug will only go on one way so please ensure that the wires are pointing up and the slot in the board is in line wi...

  • Page 16

    Ceramic bricks the following guidelines apply for all brick liners. 1. Inside the firebox, on the top of each side, release the screw of the side brick anchors (one per side) just enough to allow them to rotate. 2. Place the rear panel against the back of the firebox, on the ledge at bottom. 3. Rota...

  • Page 17

    Both front logs to rest slightly on the edge of the firebox window frame. 5. Identify the right cross log; it has a hole under on of its end and it is the shortest cross log. Place it on the right pin located on the rear log. Rest its other end in the crook of the front right log. 6. Identify the mi...

  • Page 18

    Bottom of window (wider frame) open open close close ng flashback shield (for lpg only) lpg air shutter slider open close lpg ng air shutter slider & cover window refitting 1. To refit the window, hook its top part to the firebox’s opening frame. Make sure that the wider part of the window frame is ...

  • Page 19

    Packing contents: 1 wall bracket a 2 screws b 1 screw c 2 wall anchor d 1 spacer e (detach before assembly) 1 wall bracket f switch plate alternative 1 alternative 2 alternative 3 remote control handset wall holder installation the remote control kit for this fireplace comes complete with a wall-mou...

  • Page 20

    Bottom of window (wider frame) warranty card at the back of this manual. Read the safety information section on page 4 of this manual. Operating your fireplace for your safety, this appliance is fitted with a flame supervision device which will shut-off the gas supply if, for any reason, the pilot f...

  • Page 21

    Soot or dust can be brushed from the ceramic logs and firebox walls using a soft brush. Dust can also be removed from the burner using a soft brush after removing the ceramic logs. When cleaning, make sure that no particles are brushed into the slots of the burner. Checks a periodic check of the pil...

  • Page 22

    Remote control operation your fireplace remote control helps you get the comfort, convenience and aesthetics you want from your gas fireplace. The remote controls your fireplace in different ways. Important: before you begin, please note that on this system, the settings of time, temperature and aut...

  • Page 23

    Remote control operation setting the flame use this setting when you want a particular flame level. For instance, you want to watch flames burn at their highest level and you don’t mind if the room is too hot. 1. To raise the flame, press and hold the ▲ button until the flame gets to the desired lev...

  • Page 24

    Lighting instructions for your safety read before lighting warning: if you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot, which must be lighted by hand. When lighting the pilot, follow ...

  • Page 25

    Options venting (required) approved venting accessories as per local codes. Inner front (required) see your dealer for your choice of inner fronts. Outer surrounds, trims & frets (optional) see your dealer for your choice of outer surrounds and trims and frets. Optional accessories 770zck—zero clear...

  • Page 26: Lor

    Warranty 1. Extended warranty coverage for a period of up to ten (10) years, miles industries ltd., (the “company”) or its appointed distributor will at its option pay the initial purchaser for the repair of, or will exchange the following parts or components which are found to be defective in mater...

  • Page 27

    Spare parts code description part number 1 exhaust slide assembly 4000127 2 port cover 4001820ah 3 log support 4001841 4 side bricks anchors (2) 4001283 5 top mounting bracket 4000136by 6 side mounting brackets (2) 4000135by 7 window assembly 4001378 8 burner assembly ng 4001180 burner assembly lpg ...

  • Page 28

    Spare parts ng lpg 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 24 27 26 25 30 28 29 49 50 51 52 48 41 42 43 44 45 46 47 12a ng lpg 11a 31 32 33 34 35 36 37 38 39 40 53 18 23 19 20 21 22 17 28.

  • Page 29

    Thank you ... For purchasing a valor by miles industries. Your new radiant gas heater is a technical appliance that must be installed by a qualified dealer. Please circle where appropriate - ask your installer or your dealer if in doubt. The information provided will be used for customer records onl...

  • Page 30

    Tape shut thank you for choosing a valor product postage needed were you given all documentation and manuals for your product? Yes no miles industries ltd. 190 - 2255 dollarton highway north vancouver, bc v7h 3b1 canada fold here online warranty registration at www.Valorfireplaces.Com.